Search Documents

By Fred N. Kissell, Andrew B. Cecala

In This Chapter [Where methane is emitted at longwall faces Where methane accumulates at longwall faces Using the modified shearer-clearer to eliminate ventilation eddy zones Using a walkway curtain to reduce methane buildup during the headgate cutout Control of frictional ignitions and The best location for the methane monitor] The methane released along a longwall face represents only 10%–20% of the total methane emitted from the entire longwall panel. Nevertheless, in very gassy coal seams, this methane released at the face can pose a problem because the shearer is a ready ignition source. Preventing methane ignitions at longwall faces requires four actions. The first is to provide better ventilation around the shearer to eliminate the ventilation eddy zones at the drums where methane builds up. These eddy zones are eliminated by mounting additional water sprays on the shearer to direct air into them. The second action to prevent methane ignitions is to install a water spray behind each cutter bit and regularly replace worn bits. Water sprays behind each cutter bit act to quench the hot metal streak that follows a worn bit when it strikes rock. The third is to ensure that no ventilation eddy zones are inadvertently created by poor placement of water sprays. The fourth is to ensure that the methane monitor on the shearer is in the best location to detect methane accumulations. ADDRESSING METHANE ACCUMULATIONS AT LONGWALL FACES3 Cecala et al. [1985a, 1989] and Denk and Wirth [1991] studied methane emission and ventilation patterns at longwall faces to find where methane accumulations are most likely. Although not always the case, the major source of methane at longwall faces is usually the breakage of coal by the shearer. Stress-related fracturing of the coal seam at the face, called bumps or bounces, can cause the release of additional gas (Figure 4–1).

Jan 6, 2006

By David C. Byrne

PURPOSE: Evaluate practical technological advances in hearing protective devices for use in different mining environments. RESEARCH SUMMARY: Previous NIOSH research shows that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals. Also, miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and sex. As described in the National Occupational Research Agenda, problems created by occupational hearing loss include (1) the reduced quality of life due to social isolation and unrelenting tinnitus, (2) impaired communication with family members, the public, and coworkers,(3) a diminished ability to monitor the work environment (e.g., warning signals, equipment sounds, etc.), (4) lost productivity and increased accidents resulting from impaired communication and isolation, and (5) expenses for workers’ compensation and hearing aids. Although the elimination of hazardous noise is the ideal long-term solution to the noise problem, miners will likely need to rely on personal hearing protection in certain situations for quite some time. However, it is well known that noise attenuation provided by hearing protectors as they are worn during everyday use in the workplace is usually worse than when tested under laboratory conditions. Additionally, workers may refuse to wear their hearing protection for any number of reasons. Therefore, this project was initiated to evaluate practical technological advances in hearing protectors, with an emphasis toward optimizing the balance between effectiveness, comfort, overprotection, and communication ability. Currently, the necessary in-house laboratory facilities and research techniques are being finalized. Individual experiments are planned that involve analysis of new hearing protector technology under both laboratory and field conditions. The laboratory components are to consist of con-trolled studies using human subjects and/or an anthropometrically correct artificial test fixture to evaluate the adequacy/effectiveness of various hearing protective devices. Field studies are planned to determine the actual usefulness and practicality of the hearing protectors as used in diferent mining environments. Recommendations can then be offered to the mining community regarding correct earplug/earmuff usage that maximizes recognition of hazard/warning sounds while adequately protecting the miners’ hearing.

Jan 12, 2000

By C. Golumbic

Most early research on solvent extraction of coal has been concerned with the molecular structure of coal. Although rush work is continuing, practical aspects of the subject also are being emphasized. For example, development of the Pott-Broche extraction process resulted from the discovery of very efficient solvents for the pressure-extraction of coal. Recently, Orchin and Storch reported the use of even more efficient solvents under similar conditions. In addition to the discovery of more effective solvents, the possibility of efficient extraction at atmospheric pressure is obviously of practical interest. H. J. Rose observed that phenanthrene at its atmospheric boiling point readily dispersed 80 percent or more of Pittsburgh-bed bituminous coal. This fact served as the starting point of the present investigation, ill which determination of the chemical specificity of this solvent and the chemical nature of the resulting extracts was undertaken. This paper represents a progress report of the results obtained to date.

Jan 1, 1950

By H. W. Kilau

Thermodynamic calculations indicate that an electrochemical cell might serve as an analytical device for determining the composition of high-purity metals. An equation, readily derived, for the cell voltage, E, is as follows: [E I RT In F NFe unknown sample T of L NFe standard] The cell, however, must come to equilibrium, must be reversible, and must have no thermal effects or complicating side reactions whose magnitude is indeterminable. This Bureau of Mines investigation explores the feasibility of an electrochemical technique for the analysis of high-purity iron. Experiments were conducted using room-temperature aqueous cells and high-temperature molten salt cells. The room-temperature cells proved to be irreversible. The high-temperature cells utilizing FeCl2 and a eutectic mixture of KC1-LiCl were reversible, but did not attain a constant voltage necessary for analytical considerations.

Jan 1, 1963

By James P. Bennett

The U.S. Bureau of Mines investigated the role of imported natural flake graphites in dolomite-carbon refractories used in steelmaking processes and evaluated carbon fibers as a potential substitute. Varying quantities (1.5-30 pct) of natural flake graphite and carbon fibers were added to test samples. The effect of the additions on modulus of rupture (75°-2,750° F), deformation under load (2,750° F), and air-slag-metal resistance (3,000° F) was studied. Carbon purity of natural flake graphite additions did not influence hot strength, deformation under load, or air-slag-metal resistance. When the quantity of 90-pct-carbon graphite addition varied between o and 30 wt pct, hot strength was highest, deformation under load lowest, and air-slag-metal wear the least at 10 wt pct. As test temperature increased from 500° to 2,750° F, the hot strength difference became less. Carbon fiber additions were limited to 1.5 pct in dolomite-carbon brick. At this level, physical properties were generally comparable to those obtained with natural flake graphite, but were below values obtained with 10-pet-f1ake graphite additions. Carbon fibers are not considered a satisfactory substitute for natural flake graphite.

Jan 1, 1989

By Robert S. Warfield

The Bureau of Mines investigated a geologically favorable area in the Beluga River coalfield in south-central Alaska to determine if there were sufficient minable coal reserves for onsite utilization to meet the projected thermal power needs of the Anchorage area. A program of diamond core drilling and sampling delimited a shallow saucerlike structure estimated to contain indicated reserves of more than 20 million tons of subbitminous coal in a seam over 50 feet thick that could be mined by opencut methods. A large sample of fresh coal was taken across the full width of the seam for washability studies. This sample, with 4 volume-percent of clay partings eliminated, contained 24.4 percent moisture and 16.8 percent ash and had a calorific value of 7,162 Btu per pound. The studies indicated that mechanical cleaning would be of doubtful value.

Jan 1, 1963

By Arthur E. Goddard

Radio propagation measurements were conducted in a coal mine at UHF (200 to 1000 MHz) and VLF (1 to 50 kHz) to characterize the transmission loss of intra-mine paths. The basic experimental parameters included frequency, polarization, path orientation and distance. Further tests evaluated the performance of roof-bolt vs. loop antennas at VLF and parasitic reflectors at UHF. Measurement results are summarized in a series of transmission loss curves. Examples are presented to show the use of these curves in predicting the performance of radio communication systems in mines.

Jan 1, 1973

Construction workers may be exposed to hazardous dust containing crystalline silica during site preparation when drilling systems are used. The National Institute for Occupational Safety and Health (NIOSH) found that drill dust could be decreased by using wet or dry dust reduction engineering controls, enclosed cabs, and implementing a dust control program.

Jan 1, 2009

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute, and the Bureau of Mines of the United States Department of the Interior. This paper is a continuation of a series made in cooperation with the Coordinating Fuel Research (CFR) Committee of the Coordinating Research Council (CRC), Inc. The first of this series of reports presented data on motor gasolines sold during the winter of 1935-36, and succeeding reports described motor gasolines sold during the summers and winters to and including the summer of 1941. No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-43, the semiannual reports were resumed

Jan 1, 1948

By A. Renton Amell

The rate of dissolution of U02 was measured in acid solutions similar to those used for in situ leaching, with S04 of 10-1.82 to 10-4 M, Fe(III) of 10-2 to 10-4 M and pH's of 1.1 to 2.3. The dependence of dissolution rate on pH was small and inconsistent, probably reflecting the combined effects of a very weakly polar oxidizing complex, probably FeSO4+, and a nearly neutral U02 surface. Differences in the state of the U02 surface may explain this variability as well as contrasts between these results and results reported in other work. Changing either S04 or Fe(III) concentrations significantly affects dissolution rates. Increasing low sulfate concentrations in solutions containing 10 2 M Fe(III) at pH 2 results in formation of FeSO4+. In such solutions, rates increased with (S04)/(Fe(III)) up to 1:30, thereby indicating that the oxidation of U02 by FeSO4 is more rapid than by Fe3+. However, the dissolution rate decreased at higher (SO4)/ (Fe(III)), due either to sorption of SO42- on the UO2 surface or to formation of other less reactive sulfate complexes such as Fe(S04)2 or FeHSO4+ However, Fe(III) concentration is the dominant factor in determining solution rates. The rate was directly proportional to ferric iron concentration, indicating that the rate-determining step of the dissolution reaction is a single-electron oxidation by a ferric complex. Dissolution rates were lower in solutions of 0.1 and 1.0% H202 (0.029 and 0.29 M) than at similar concentrations of ferric iron because of formation of an insoluble surface coating of uranium peroxide, UO4?4H20. This phase may limit the value of hydrogen peroxide as an oxidant in lixiviants, not only by its very low solubility, but perhaps also by filling pores and reducing permeability in the ore body.

Jan 1, 1978

By Ralph B. Youtz

This paper describing mining methods at, the Eighty-Five mine of the Calumet and Arizona Mining Co., Valedon, N. Mex., is one of a series being prepared by the United States Bureau of Mines on mining methods, practices, and costs in the various mining districts in the United States. The Eighty-Five mine is in southwestern New Mexico, 3 miles southwest of Lordsburg, Hidalgo County (see fig. 1). The mine produces normally 7,000 to 8,000 tons per. month of silicious copper-gold-silver ore, and employs approximately 200 men underground and 40 on-the surface. Mining is done by shrinkage and cut-and-fill methods.

Jan 1, 1931

By Larry R. Wilson

The development effort described herein was directed toward the design and development of a flexible communication system to provide two-way section communications between any telephone on an MCM-101 telephone FDM exchange and a miner provided with a uhf walkie-talkie transceiver. The system also provides normal communication between miners within a working section through the uhf coupler interface repeater.

Jan 1, 1976

By J. C. Edwards

Fire experiments were conducted in the Safety Research Coal Mine (SRCM) at the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, with coal, diesel-fuel, electrical-cable, conveyor-belt, and metal-cutting fire sources to determine the response of fire sensors to products-of-combustion (POC). Metal oxide semiconductor (MOS) and smoke fire sensors demonstrated an earlier fire detection capability than a CO sensor. This capability was of particular significance for a conveyor-belt fire in which the optical visibility was reduced to 1.52 m with an increase in CO of less than 2 ppm at a distance of 148 m from the fire. Application of a neural-network program to the sensor responses from each type of fire source resulted in correct classifications of coal, diesel-fuel, cable, belt, and metal-cutting combustion with a mean of 96% of the test data correctly classified.

Jan 1, 2000

By Richard L. Sayrs

"The Stiner zinc prospect near the north boundary of Union Tennessee, and the Bunch Hollow property 5 miles northeast in Claiborne County, Tennessee, were diamond-drilled by the Bureau of Mines during the period .September 1, 1944, to February 22, 1945. Seventeen holes totaling 5,687 feet were completed, 13 of which, totaling, 5.083 feet, were on the Stiner property and the remainder, totaling 604 feet, at Bunch Hollow.The Stiner prospect is about 1 mile east of the old workings known as ""New Prospect"" or ""Lead Mine Bend."" The Federal Geological Survey made a study' of the area early in 1944. The prospect was first visited in August 1944 by Bureau of' Mines engineers3/ accompanied by members of the Federal Geological Survey.4/ The locality is reached by traveling State Road 33 north-about 9 miles from Maynardsville, Tenn., thence northwest about 7 miles by an improved county road that leads to the mine (fig. 1). The tract comprises an area of about 181 acres held by G. S. Stiner of Sharps Chapel, Tenn.; it is now under option to the Universal-Exploration Co. of Jefferson City, Tenn.The Bunch Hollow property, about 5 miles northeast of the Stiller prospect, was also studied by the Federal Geological Survey previous to being;Visited by Bureau of Mines engineers in August 1944. It is reached by traveling north from Maynardsville, Tenn., on State Road 33 about 13 miles, thence northwest by county road 6 miles to the property (fig. 1). The last 3 miles of the county road are in poor repair but are passable during the entire year. The property comprises an area of approximately 300 acres and is held by the imperial Mining Co., Pressman's Home, Tenn.Few reliable data are available as to the history of the Stiner prospects themselves. However, the New Prospect mine, 1 mile west, has had a colorful past, This mine was opened in 1883 and was worked intermittently until 1918, by which time more than 65,000 tons of concentrates had been shipped. No further work was done until 1942, when the mine pillars were robbed and 1,900 tons of ore averaging 25 percent zinc was shipped to the New Jersey Zinc Co., Austinville, Va."

Apr 1, 1946

By F. S. Crawford

"After many years of safety activity in the United States in one form or another it becomes increasingly evident to those in contact with safety work that to achieve continuous good results in accident prevention there must be an aggressive organization behind the safety movement at each mine with fairly definite plan and policy. A study of the methods used by various companies and the results they have attained will be of value to the common cause of safety promotion.A study has been made of the safety records of the Menominee iron range in the Lake Superior district, and of data from the county mine inspector's report. Several companies on this iron range that have attained a certain measure of success in their work of accident prevention have given data, and a summary of their safety methods is presented.The Menominee iron range of Michigan lies in the southern portion of the upper peninsula of Michigan, bordering on Wisconsin. It consists of two main. divisions--the West Menominee Range, situated in Iron County in the vicinity of Iron River and Crystal Palls, and the East Menominee range situated in Dickinson County in the neighborhood or iron Mountain, Mich. The mines about Iron River and Crystal Falls are peculiarly subject to fires in a carbonaceous, sulphur-bearing black slate which appears in the footwall. This gives considerable trouble because fires in this material start from spontaneous heating. The methods of mining are top slicing and open stoping, working on benches along the sides of the stopes. The character of the ground varies from medium Soft ore to relatively hard ore which permits open stoping. Approximately one-third of the operating mines are equipped with a fan for main mechanical ventilation. The remainder are ventilated by natural draft. The East Menominee range is the older, top slicing having been used there for a number of years, and the timber mats have boon well developed. In common with all districts, some companies pay more attention to safety than others, although, those which do riot have the best records do pay some attention to safety.During the past three years the annual production per man employed has remained about constant, but in many mines a general decrease is shown in the accident record. The variation in the results attained can be ascribed mainly to the earnestness with which accident-prevention work is pursued, essentially regardless of the method of mining used. This is shown to be generally true, because the record indicates a steady decrease in one mine with an active safety department, while in adjoining mines with the same kind of ground and method of mining but where not such intensive attention has been paid to safety work, the accident record is high."

Oct 1, 1931

By W. A. Selvig

"The purpose of the investigation described herein was to determine how closely different laboratories can check one another in making determinations of fusibility of coal ash with the De Graaf electric coal-ash fusion furnace: how well duplicate determinations by the same laboratory will check, and how the results with the De Graaf furnace compare with those of the standard gas-furnace method of the American Society for Testing Materials.4Thanks are due the following laboratories who cooperated in this study by making fusibility tests with the Do Graaf electric coal-ash fusion apparatus: J. J. Brennan, testing engineer, Northern States Power Co.; R. E. Gilmore, superintendent, Fuel Research Laboratories, Canadian Department of Mines A. T. Leavitt, president, and W. Mueller, chief chemist, Hamilton By-product Coke Ovens. Ltd.; Edgar Stansfield, chief chemical engineer, Scientific and Industrial Research Council of Alberta. Canada; and H. S. Vassar, laboratory engineer, Public Service Electric and Gas Co.The ash-fusibility determinations by the standard gas-furnace method were made in the Coal Analysis Laboratory of the Bureau of Mines at Pittsburgh under the direction of H. M. Cooper, associate chemist. The investigation was made at the suggestion of A. C. Fieldner, chief engineer, Experiment Stations Division of the Bureau of Mines.Routine determinations of the fusibility of coal ash are made in the laboratories of the United States Bureau of Mines by the gas-furnace method. This method was standardized after considerable experimentation5 on the nature of the fusion of coal ash and the various factors which affect its determination. The method was subsequently adopted by the American Society for Testing Materials as one of its standard tests."

Jun 1, 1930

By James F. Devine

This Bureau of Mines report describes tests conducted at three sites to determine if, and to what extent, a vertical presplit fracture plane placed between a blast point and detection point will reduce vibration levels. Statistical analyses indicate that the presplit fracture plane did not reduce the vibration level.

Jan 1, 1965

By Douglas Talley

This report describes a 4-inch diameter borehole probe which contains a low light level TV camera, magnetic compass, light illumination source, bottom/water detector sensor and a pointing angle sensor. The camera viewing angle is at a right angle to the probe's body. All data from the sensor is multiplexed into the closed circuit camera video for transmission on a single 50 ohm coaxial cable to a surface control unit. Likewise control of the probe's power, zoom lens, focus, panning and aperture is accomplished via a down-link multiplexed on the same cable.

Jan 1, 1984

By J. E. Spurr

"Zinc Industry in BelgiumBy March F. Chase, Consulting Metallurgist, Bureau of MinesBelgium for many years was the principal spelter producing country of the world. Gradually its production was surpassed by that of Germany, and Germany in turn lost first place by the production in the 77ti.tad States. For the ten years previous to 1914, 21.6 per cent of the world's spelter was produced in Belgium. Of this production approximately 40 per cent was exported. A large percentage of the balance was rolled and of the shoots thus produced a considerable quantity was also exported.From an economic standpoint even before the war, the Belgian industry was in a unique, if not praoarious, position. Dependent upon foreign countries for ore and foreign markets for sale of products, smeltor was at a distinct disadvantage when compared with some of those of other localities. These disadvantages were partly offset by cheap coal and labor and by whatever there is of value in experience and what we may term for want of a better expression smelting tradition. However intangible this latter may be, it did have and has today an influence on commercial operations.One must not overlook the effect it will have on the revival of the industry. It may not be the determining factor but the fact that for so many years this industry flourished in Belgium, and played such an important role in the industrial life of the country will decide many operators to attempt to re-establish their operations.In 1913 the Belgian spelter plants produced 204,220 long tons of spelter or approximately 20 per cent of the world's production. During this year 500,000 to of ore were treated. The actual value of all of the products derived from treating sine ore amounted to 225 million frames."

May 1, 1919

By D. G. Kesterke

Research was conducted to determine the feasibility of extracting elemental oxygen from silicate-bearing melts by high-temperature electrolysis. The method was based on a modification of existing processes for electrowinning metals from their oxides dissolved in molten halide systems. Electrolyses were performed at temperatures ranging from 1,050° to 1,250° C in boron nitride cells that incorporated a silicon carbide cathode and an iridium anode. The electrolytes contained volcanic scoria as the oxygen source, plus mixtures of BaF2 and LiF as fluxing agents. Cell gases containing almost 14 volume-percent oxygen were obtained. The average anode current efficiency for several experiments of extended duration was calculated to be 55 percent. Cell design and operating conditions are described, and some of the problems associated with the process are discussed.

Jan 1, 1971