Search Documents

By John Durkin

Electromagnetic narrow-band signals were transmitted through the earth at 27 coal mines located throughout the United States. From those Bureau of Mines tests, apparent earth conductivity values were derived based upon a homogeneous half-space model of the earth. The derived conductivity values were found to be inversely proportional to the transmitted frequency and mine depth. A linear regression model relating the logarithm of the conductivity to the mine depth was formulated, and the results indicate that the mine depth can be an adequate predictor of the apparent earth conductivity above coal mines. Apparent earth conductivity was found to decrease with mine depth.

Jan 1, 1984

By Robert C. Bates

This Bureau of Mines report converts published data on the cost of ventilating uranium mines to a common price base and analyzes these data to determine the cost per ton of uranium ore at various levels of radiation exposure control. There appears to be an exponential increase of cost as the radiation level is lowered. The 1967 base costs are extrapolated to present dollars, and some cost comparisons are given for other radiation control measures.

Jan 1, 1981

By J. A. Pile, Virgil Miller, R. G. Peterson, F. B. Petermann

"INTRODUCTION As virtually no published data are available on the sintering of fine, minus-100-mesh, ferrograde manganese ores, it is most opportune to present data on the amenability of various fine ores and mill products to the sintering process. These data cover the sintering or nodulizing of finely crushed, high-grade pyrolusite and rhodochrosite ores, sintering of manganese carbonate flotation concentrate, sintering or nodulizing the calcine from the deleading of a manganese oxide flotation concentrate, and sintering the calcines made in a Herreshoff furnace from the treatment of manganese sulfate products.If finely sized products are to be smelted in the present electric or blast ferromanganese furnaces, they must be sintered or nodulized. The only specification as to the size of the sintered or nodulized product is that it must pass a 6-inch screen and not contain over 1t-1/2 percent minus 20-mesh material. The minimum-maximum size has not been established. Undoubtedly this opti mum size will be set by the ferromanganese industry when ample quantities of manganese oxide sinters have been smelted."

Mar 1, 1942

Reduce potential for steering errors during tramming of articulated vehicles, particularly when the operator is seated to the rear of the machine pivot point and is tramming in reverse. Approach Position-sensing and feedback cylinders were applied to the steering cylinders of two S&S cleanup tractors to cause the steering-control lever to match the orientation of the vehicle sections. The vehicles were tested in two working mines. How It Works A position-sensing cylinder (see Figure 1, Item A) is attached to one of the steering cylinders in the cleanup tractor steering system. As the steering cylinder piston rod is actuated by movement of the control lever, hydraulic oil flows from the position sensing cylinder to the feedbck-cylinder (B), causing the feedback-cylinder piston and rod to move. The outside end of the rod repositions the the steering-control lever until its angular position corresponds to the orientation of the vehicle sections.

Jan 1, 1978

By Richard A. Dick

Eight blasts were fired in a 2-1/2-ft bench in the Stewartville member of the Galena Limestone formation in an aggregate quarry near Stewartville, Minn. The shots were dimensionally proportional to production-size bench blasts and were about 5 to 10 percent of full scale. The effects of site, timing of initiation, and burden-to-spacing ratio were studied in a 2 x 2 x 2 factorial experiment, using three boreholes, caw;, containing a 1/2-in charge diameter of high-density ammonia dynamite, in each blast. Detonation velocity measurements indicated that the dynamite detonated satisfactorily in the 1/2-in charge diameter. The effects of the three experimental variables were analyzed by weight for the percentage of oversized material produced and for size distributions determined by screening the entire muckpiles. The bench faces were painted before each shot in an effort to determine the origin of the oversized material. The square pattern (burden and spacing = 15 in) produced finer overall fragmentation and less oversized material than the rectangular pattern (burden = 15 in; spacing = 22-1/2 in). Sites 1 and 2 were about ft apart. Although site 2 produced slightly better overall fragmentation than site 1, the amounts of oversized material produced showed no significant difference. The timing of initiation (instantaneous or delayed) did not significantly influence the overall fragmentation or the amount of oversized material produced.

Jan 1, 1973

By Lawrence G. Houk

Monazite sand is the only commercial source of cerium, other rare-earth metals and thorium. Although used in rather small quantities, it is essential to many industries. The United Unites is entirely dependent upon British India and Brazil for its supplies. Monazite sand or sand imported under the tariff classification for monazite was shipped to the United States in greater quantities, in 1940 than ever before. About 75 percent of our imports was from British India and most of the remainder from Brazil. If need be, Brazilian production can be expanded to supply all of our essential requirements, and the theater of war expands in the Pacific Brazil may supersede India as the principal source. PHYSICAL PROPERTIES The mineral monazite is generally honey yellow or may vary from greenish yellow to clove brown. The grains are small and resinous in luster, and range from subtranslucent to opaque. The specific gravity varies

Jan 1, 1943

By P. H. Floyd

Laboratory test work has shown that the Germania ferberite-scheelite ore can be concentrated to an acceptable grade. A ferberite concentrate assaying 66.9 percent tungstic oxide was made, with a recovery of 75.4 percent. A second concentrate of ferberite and scheelite was made assaying 54.2 percent tungstic oxide. Final beneficiation of combined rougher gravity concentrates was accomplished by roasting, magnetic separation, sulfide flotation, and retabling, to give a final ferberite-scheelite concentrate of 66.2 percent tungstic oxide, with a 91.1-percent recovery. INTRODUCTION This presentation covers the results of laboratory beneficiation tests conducted on tungsten ore from the Germania Consolidated Mines, Inc., by the Bureau of Mines Mineral Dressing Section, Northwest Electrodevelopment Laboratory, Albany, Oreg. This mining property is near Fruitland, on the southern edge of the Spokane Indian Reservation, Stevens County, Wash. The Germania district produced tungsten concentrates before and after World War I; interest is being renewed in the district because of the metal shortage.

Jan 1, 1954

By A. G. Starliper

Laboratory studies were made to produce whiskers of tungsten over a wide range of operating temperatures. Hydrogen reduction of tungsten hexachloride in a vacuum furnace at temperatures from 2,7000 to 3,3000 C yielded a small quantity of tungsten whiskers, provided a low degree of supersaturation was maintained. Direct measurements of 3,000,000 to 4,000,000 psi were obtained for the ultimate tensile strengths of individual whiskers averaging 3 to 4 microns in diameter with average aspect ratios of 1,000. This compares with strengths of 300,000 to 400,000 psi for 13-micron-diameter commercial filaments.

Jan 1, 1968

By J. Burlin Johnson

In small-scale blasting experiments conducted in the Bureau of Mines laboratory, small charges were used to produce craters in blocks of concrete mortar. The results are compared with larger scale experiments of other research workers, and the comparison demonstrates the similarity of the results obtained and indicates that small-scale blasting should be a useful tool for predicting large-scale blasting effects. INTRODUCTION The purpose at this investigation was to conduct blasting experiments in mortar in the laboratory and then, by comparing the results with those from larger scale field blasts in rock to determine to what extent, if any, the laboratory results resemble those in the field. The work described herein was the initial phase of a project aimed at evaluating small-scale blasting as a tool for use in improving blasting techniques. It is evident from the stand-point of control and cost that small-scale blasting would be valuable in the study of rock fragmentation by blasting in mines and quarries, if the extrapolation is valid.

Jan 1, 1962

Provide an instrument for continuous remote monitoring of carbon monoxide concentration in underground mines. Approach A carbon monoxide fixed? point continuous monitor consists of two modules. A line-powered control module is designed to power a remote transducer module; provide continuous readouts, visual and audible alarms, operational checks; and activate fans and equipment shutdown circuits if preset CO concentration levels are exceeded. How It Works The control module must be used in conjunction with a single transducer module. Developed under contract. the control module is a wall-mounted Instrument which contains a readout and alarm capability and power supply

Jan 1, 1981

By R. H. Grau

Researchers from the National Institute for Occupational Safety and Health have demonstrated that mine-wide ventilation in large-opening stone mines can be improved by using low-pressure, high-volume propeller fans and constructing stoppings in key locations to direct and control airflow. In light of these findings, a comparative study was conducted to determine if a portable diesel-powered propeller fan could per-form more efficiently for dust dilution and transport than an axial vane fan for localized ventilation. The objective of this study is to evaluate both fan types for ventilation efficiency at an underground dump/crusher facility in a limestone mine. Results showed an improvement with the propeller fan to dilute both the respirable dust and the respirable silica dust around the dump/crusher facility. Overall, an average reduction of 20% in respirable dust and silica was observed at the dump/crusher location with the propeller fan.

By Adrian J. Mathias

This report presents the results of an investigation of a mine production-scheduling model and a critical path analysis for long-range mine planning. An example is given to illustrate how these techniques might be used to plan long-range development and production scheduling for a large underground mine. The model, based on estimated ore block grades and tonnages, and on designed mine development layout, simulates mining of ore blocks in a sequence necessary to fulfill mill requirements for ore tonnage and grade evaluation within pre-established system restrictions. Simulated production schedules are obtained as output from the model. These production schedules are then incorporated into a critical path analysis to determine the sequence for the long-range development work so as to fulfill the production schedules and thereby meet the ore grade and tonnage requirements of the mill.

Jan 1, 1967

By T. E. Gray

This report describes the preparation characteristics of the three significant coal beds in Greene County, Pa. It is one of a series planned to determine which coals are suitable for the production of metallurgical coke, either as mined or after beneficiation. Over 12.5 million tons of coal was produced in Greene County in 1956, of which approximately 10 million tons was cleaned mechanically in 8 cleaning plants. The Bureau of Mines has estimated that 3.5 billion tons of recoverable coal remained in the county as of January 1, 1954.

Jan 1, 1958

By Robert Stefanko

Transients are results of sudden changes which take place in power systems and can be created by the opening and closing of switches and circuit breakers or the occurrence of a fault anywhere in the complex. Transients are of short duration, and the time during which they occur is an extremely small percentage of the total operating time. However, it is during these short periods that the greatest electrical stresses occur, mainly due to excessive currents or voltages. In extreme cases, system parts are damaged, and equipment failure follows. Safety can be further compromised because anomalous voltages can exist at machine frames. For several years, the electric utilities have been well aware of the serious nature of transients on their systems, but problems firmly believed to directly result from these phenomena are just now becoming apparent to the coal mining industry. The situation became discernible after the underground introduction of high voltage distribution systems (along with vacuum circuit breakers) and sensitive solid state electronic apparatus. In order to protect against such transients, knowledge about their characteristics and origin must be obtained.

Jan 1, 1974

By d&apos, Kathleen J. Amico

THIS summary appears in Minerals Yearbook volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U.S mineral production also is included.

Jan 1, 1964

By John P. McDonnell

Cable supports offer several advantages over traditional secondary support methods by enhancing stress redistribution to pillars and gob areas, minimizing or eliminating timbers and cribs that reduce ventilation, eradicating material-handling injuries related to placement of crib supports, and providing a cost-effective alternative to secondary support. The U.S. Bureau of Mines, in researching alternatives to traditional roof support methods, designed and installed high-strength cable supports to improve the stability of longwall gate road and bleeder entries in a Western U.S. coal mine. With the cooperation of industry, methods were developed to install cable supports in a tailgate and bleeder entry test area using traditional resin cartridges. Resin-grouted cable bolts were also installed and evaluated in additional longwall gate road and bleeder entry systems at the study mine. The cable-bolted areas successfully maintained roof support throughout the tailgate and bleeder entries. Cable supports replaced wood cribbing as secondary support in the bleeder entry system and minimized the use of cribbing in the longwall tailgate entries. This report describes the theory, application, and advantages of cable supports and presents mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 2010

By M. E. Volin

The Buckeye manganese deposits are in Stanislaus County, Calif., about 33 miles south of Tracy. From 1917 to 1919 the deposits produced 13,370 tons of ore reported to average 46 percent manganese and 14 percent silica. The deposits are confined to two areas of' development, known as the north mine workings and the south mine workings, about 700 feet apart horizontally. Mineralization occurs chiefly as rhodochrosite and psilomelane interbedded in cherts of the Franciscan formation. As a part of the Bureau of Mines program of investigation and development of domestic mineral deposits, a development project was started November 25, 1940, and completed June 27, 1941. The Federal Geological Survey cooperated by mapping the topography and geology and logging the drill cores. The program included road and. trail building, trenching, underground excavation, diamond drilling, and sampling. The following pages mention the location, brief the history, and note the physical .features of' the district. Mine workings are sketched, the deposit is described, and the plan of the project is noted. The work performed by the Bureau of Mines is explained in the concluding pages with a summary of the drill-hole logs.

Jan 1, 1949

By E. D. Gardner

"The Bureau of Mines has studied blasting practices in metal mines of the Southwest. The investigation of blasting drift rounds showed among other results, that cut-holes in ground difficult to break could be chambered to advantage under some conditions.In open--cut mines, chambering nearly all holes before blasting is the common practice. Two or more free faces are generally maintained in this type of work, and the amount of explosive necessary to break any bench or bank can usually be estimated from the yardage to be moved. However, in blasting drift or tunnel rounds only one free face is available before the cut-holes are shot, and the quantity of explosive required is generally ascertained best by trial.In addition to being the most difficult to break, the cut-holes are the most important of a drift round. When the cut-holes ""break bottom"" less work is required of the other holes, and a full break of the round is generally obtained. In ground difficult to blast, extra care and expense are justified to insure that the cut-holes ""break bottom.""At many mines the work is so organized that all blasting is done at the end of the shift, and a decided advantage would have to be gained to make chambering of the cut-holes economical. Also, in many mines blasting during the shift would not be practical. One or two holes could probably be drilled during the time necessary to do the chambering. However, under certain special conditions, such as in small operations or those where ""leasers"" or contractors are working, drill holes could be chambered should there be an advantage in doing so. Moreover, in some mines it might be practical to chamber the cut-holes at the lunch hour. In ordinary rounds the cut-holes are generally drilled by noon. It would not be necessary to tear down the drill or remove tools from the face to do this work of chambering."

Feb 1, 1928

By E. J. Gleim

A list of permissible mine equipment, tested and approved previous to January 1, 1942, was published In Bureau of Mines Information Circular 7207.3/ The present list covers additional equipment approved during the calendar year 1942. The items have been numbered to indicate the order in which each type of machine or device was approved in its particular classification. Thus, Information Circular 7207 gives four air compressors on the Bureau's active list, and the present circular gives the fifth to be approved. Items 90 and 94 under Loading; Machines land Conveyors also appear in Information Circular 7207. These numbers are repeated hero to show that approval was granted during 1942 for additional voltages on machines previously listed one voltage only. Equipment listed in these circulars is approved by the Bureau of Mines only when found upon inspection and test to comply with minimum standards of safety as outlined in schedules prepared on the basis of many years of experience in dealing with safety problems of the coal-mining industry. The use of such equipment in mines known to be gassy, as well as in those which may become so, is earnestly recommended in the interests of safety. This circular is published so that the industry may be kept informed as to the many types of machines, devices, and lamps that arc available for reducing explosion and other hazards incidental to coal mining. The present paper and Information Circular 7207 together give the complete list of all available permissible .Mine equipment.

Jan 1, 1943

By R. V. Ramani, J. M. Mutmansky, J. Qin, J. Organiscak, R. Bhaskar

"The results of a two—year research study into the relationship between quartz dust levels in host material and in respirable dust in continuous mining sections are presented in this paper. The experimental design and sampling procedures for underground data collection are outlined. The sample analysis procedures for quartz determination, the ¬analysis results and conclusions of the study are discussed.The results of the study indicate that the quartz contents of the airborne dusts are generally higher than those in the host material and bulk samples; and the quartz content increases with decreasing size of the airborne dust. The source for quartz appears to be the roof and the floor materials rather than the coal seam itself. It also appears that the material containing quartz may be breaking into a different size distribution than coal.INTRODUCTION Without doubt, the potential for permanent and severe health damage exists due to respirable dust in the work environment. The attention directed at the reduction of respirable airborne dust to levels below those specified in the law and the achievements to date in meeting these standards are but a reflection of the recognition by many parties government, industry, and labor - of this potential and the need to reduce it.The ambient dust standard in underground U.S. coal mines (2 mg/s3) has a qualifier (Code of Federal Regulations, Title 30, Part 71.101) to determine an applicable dust standard when a respirable dust sample contains more than 5% quartz. This standard is frequently referred to as the ""reduced standard."" The reasoning behind the reduced standard is the relative toxicity of the quartz dust compared to that of pure coal dust. As the quartz levels in samples increase, the applicable standards become more stringent and maintaining the workings in compliance becomes increasingly difficult.The number of underground work locations operating under the reduced standards has shown a dramatic increase since 1980 (Figure 1). For comparison purposes, there were no mining entities operating on reduced standards prior to 1977. The emergence of this problem, which affects the health and safety standards on one hand and creates severe compliance problems on the other, has been rapid."

Jan 1, 1990