Search Documents

By Harry W. Campbell

In 1986 at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 2 acre North Sisters Rocks Wilderness Study Area (OR-12-8) in order to evaluate its identified mineral resources. The Wilderness Study Area is located in Curry County, Oregon, about 15 miles north from Gold Beach. No mines, prospects, or mining claims were located inside the study area, and no mineral resources were identified. Stone from the study area could be quarried and used for construction purposes; however, two nearby quarries have sufficient stone to satisfy local construction needs. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and mineral resource potential of the North Sisters Rocks WSA (Wilderness Study Area) 1/ at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of investigations will be used to help determine the suitability of the North Sisters Rocks WSA for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1987

By G. B. Atkinson

To develop technology to help assure an ample domestic supply of zinc, the Bureau of Mines is investigating an aqueous chlorine-oxygen leaching process for treating complex sulfide concentrates. This report discusses the purification of aqueous C12-02 leaching solutions by utilizing zinc cementation to remove Cd, Co, Cu, Ni, and Pb. Additional processing of the purified solution is necessary to produce ZnC12 crystals suitable for molten-salt zinc electrowinning cells. The effects of solution temperature, reaction time, zinc dust concentration, ZnCl2 concentration, and degree of agitation on the removal of impurities were investigated for both simulated and actual leaching solutions. Zinc dust addition to a leaching solution at 30° C decreased the Cd, Cu, Ni, and Pb concentrations to acceptable levels of less than 3 mg/1 each. By increasing the solution temperature to 75° C, the cobalt content was decreased to less than 5 mg/l, an acceptable level for producing electrolytic cell-grade ZnC12. Impurity removal rates from ZnCl2 solutions are Pb>Cu=Cd>Ni>>Co. An increase in the solution temperature increases the rate of removal for these metal impurities.

Jan 1, 1982

By John W. Taber

"INTRODUCTION AND SUMMARYDiscovery of these unusual fluorite deposits was brought to the attention of the Bureau of Mines late in 1951, shortly after the first locations were made. A brief investigation of the deposits by the Bureau revealed seven principal outcrops of fluorite in two areas. The smallest outcrop continuously exposes massive fluorite over an area 25 by 55 feet; the largest outcrop is a similar exposure 180 by 240 feet. The deposits, appear to be sharp-walled, low-angle, tabular ore bodies in granite and are at least 10 feet thick.The Bureau investigation of the deposits included bulldozer strip-trenching, drilling and blasting rock cuts, and channel sampling across three of the largest outcrops. This sampling indicated an average grade of 97.2 percent CaFp and 1.44 percent SiO2.Preliminary metallurgical tests on the ore indicate that it can be concentrated to acid-grade specifications by simple gravity methods. One laboratory test recovered 78.4 percent of the fluorite in a product containing 98.7 percent CaF2, 0.25 percent SiO2, and 0.10 percent Fe2O3."

Oct 1, 1952

By H. K. Sacks

The Bureau of Mines has improved a mine dust incombustibles analyzer originally developed at the Bartlesville Energy Research Center (BERC). This analyzer provides quick, accurate analysis of the percentage of incombustible material present in dust samples taken from mine ribs, roof, and floor so that costly overdusting may be eliminated while still maintaining a proper level of incombustibles. The changes being effected on the present design of the BERC model IV rock dust analyzer should simplify its operation and calibration procedures, resulting in increased accuracy.

Jan 1, 1976

By George H. Johnson

An evaluation of the diamond-bit-performance data accumulated from core-drilling cherty limestone and cherty dolomite reveals that the percentage of core recovered and the physical characteristics of the bits and diamonds used are economically significant. One of the established trends, of particular interest to those engaged in diamond drilling, is that bits set with small, low-quality, West African drill bort are the most economical. Detailed analysis of the factors that affect diamond-bit performances, such as diamond size and quality, bit size and type, percentage of core recovered, and the physical characteristics of the bit matrices are assessed in the tables, charts, and discussion.

Jan 1, 1958

By D. E. Wolfson

Destructive distillation (carbonization) was shown to be a feasible method of disposing of scrap tires. The Bureau of Mines conducted tests under a variety of conditions. Solid, liquid, and gaseous products were produced, recovered, and analyzed. The quantities of the various products were shown to be quite dependent on the test temperature. Variability in composition of the liquid and gaseous products with changes in test temperature was also significant.

Jan 1, 1969

By R. C. Bates

Uranium mine workers? daily exposure to radon daughters was estimated by two methods of sampling, detailed and spot-check. Both methods involve time- weighting measured exposure levels to arrive at an average exposure figure. Random sampling, or sampling without regard for the duration of exposure, has proved inadequate for estimating average exposure levels. During the first phase of the study, the breathing zones of eight workmen in three underground uranium mines were sampled for an entire shift; 20 to 36 radon-daughter samples were collected per man-shift, Analysis of these data indicated that a suitably accurate estimate of the full-shift exposure could be made by time weighting a considerable lesser number of representative radon-daughter samples. This analysis led to the spot-check method of estimating full-shift exposures to radon daughters. Additional detailed studies were made in seven mines to Learn more about the full-shift radon-daughter exposures and to test the spot-check method, In all, 617 radon-daughter samples were taken in 10 underground uranium mines during 26 man-shifts, and the spot-check method was tested 35 times.

Jan 1, 1962

By A. F. Baker

The Bureau of Mines conducted pressure-drop studies in a 4-foot-diameter simulated blast furnace shaft to compare anthracite metallurgical briquets with coke and formcoke. The test materials were used alone, layered, and in mixed burdens of commercial fuel-to-ore ratios. Anthracite briquets had a higher pressure drop per foot than furnace coke, but they had a lower pressure drop per foot than formcoke. This appears to be due to packing and shape, as well as to particle size. The superficial air velocities at which beds of briquets and furnace coke disrupted were about the same. However, if briquets of the shapes and sizes tested are substituted for furnace coke in commercial metallurgical furnaces, higher blowing pressures will be required to deliver comparable amounts of air. Test burdens with more than 5 percent material smaller than 1/4-inch diameter showed significant increases in resistance to airflow.

Jan 1, 1967

By R. M. Santmyers

Thorium and cerium are two of the group of elements known as "rare earth metals," and are obtained from the mineral monazite. Previous to the employment of thorium and cerium in incandescent gas mantles these elements were nothing more than laboratory curiosities, as the rest of the rare-earth metals are to-day. The most important salts of these rare earths are the nitrates. In the manufacture of gas mantles, thorium nitrate is the principal ingredient and forms prom 92 to 99 per cent of the impregnating material; the other 1 or 2 per cent is largely cerium nitrate and is quite as necessary, for without it there would be little luminosity to the mantle when in use. When the mantle is "burned off," the nitrates are changed to oxides. The monazite used as a source of thoria contains from 6 to 9 per cent of thorium oxide (Th02) and 24 to 32 per cent of cerium oxide (Ce203). As only the thoria and a very small hart of the ceria from the monazite could be used in gas-mantle manufacture, for a time the residues consisting mostly of ceria with somewhat smaller quantities of other rare earths found no commercial application. Later, however, they came to be utilized in several ways, the most important being: (1) the manufacture of cored flaming arc carbons, a great, irmprovement over the plain arc carbons used in electric lighting; (2) cerium metal used in the manufacture of pyrophoric or sparking alloys or "flints" for automatic pocket lighters and miners' lamps; and (3) the production of special kinds of optical and art glass.

Jan 1, 1930

By G. R. Fitterer, E. A. Krockenberger, B. E. Sockman, R. B. Meneilly, J. F. Eckel, E. W. Marshall

"Steel manufacturers have noticed a decided tendency on the part of many of their customers to become more exacting in their steel specifications. Under these conditions, the steel must not only meet the specifications of physical properties (tensile strength, reduction of area, elongation, impact strength, grain size, normality, etc.) and the chemical analyses, but must also pass the inspection test of ""cleanliness.""By cleanliness is commonly meant the absence of oxide and sulphide inclusions. Other foreign particles such as furnace or ladle slag, ladle and runner brick, etc., must also be absent. The determination of cleanliness at present is usually made by microscopic inspection or macroetching.The rejection of steel for lack of cleanliness is increasing, out cleanliness is one of the most difficult requirements for the manufacturer to fill. The reason for this is that every steel inspector has a different conception of a. clean steel. A material which does not pass the examination of one inspector way be regarded as entirely satisfactory by the metallurgist of an¬other company. The cause of this confusion and disagreement concerning the definition of a clean or a dirty steel is simply that as yet no standardized procedure for the determination of impurities has been proposed and generally accepted, since many variables are encountered which interfere with the development of a satisfactory method. An idea of the complexity of this situation will be obtained from the following pages.A Survey of Proposed Analytical MethodsAlthough no analytical method has been accepted, many procedures have been proposed, as may be seen in Table 1. Therein are listed 16 of the better-known processes, pith references to the work of their originators, their mechanisms of determination, and their applicabilities. Among these is included the electrolytic method developed by one of the present authors, and some comparison between this and previously proposed procedures may be obtained by a study of the table. It appears that this new method Las many advantages over the others, and this paper presents a critical Study of its value."

May 1, 1933

By Martin H. Stanezyk

The Bureau of Mines investigated leaching of selected copper sulfide minerals and a composite of impure flotation concentrates at elevated temperatures and pressures with ammoniacal solutions. Copper 1 (tractions of 96 percent were obtained by leaching chalcopyrite at 75° C under oxidizing conditions for 60 minutes. An extraction of 99 percent of the copper contained in the composite concentrate was obtained by leaching the product for 90 minutes at 75° C. In tests of bornite, chalcocite, and covellite, 90 to 97 percent of the copper was extracted at 20° C provided an 8-hour reaction period was used. At 75° C essentially complete dissolution of the copper from these three minerals was accomplished in 60 minutes. Additions of ammonium sulfate to the leach solutions were required to obtain high-percentage extractions of the copper from bornite, chalcocite, and covellite. Although ammonium sulfate was not required when digesting chalcopyrite, copper extraction was enhanced and less free ammonia was required when ammonium sulfate was added to the leach pulps. The chemistry of leaching copper minerals was studied. It was C, termined that chalcocite altered to covellite as one step in the dissolution When leaching iron-bearing copper sulfides, hydrated iron oxide formed on the mineral surfaces, indicating that a diffusion process prevailed. No evidence of covellite was detected.

Jan 1, 1966

This Bureau of Mines publication contains five papers pertaining to the effective grounding of mine power systems, as follows: Ground-check monitor types and safety characteristics; ground wire monitors for surface coal mines; ground bed design and measurement; electrical ground rod corrosion; and a continuous ground bed resistance monitor.

Jan 1, 1979

By S. J. Davenport

The increased consumption and importation of fluorspar and cryolite (1)3/ in recent years, and especially the addition of fluorine compounds to drinking water in the United States, have aroused renewed interest in the properties of such compounds and possible health hazards incident to their use. It has been suggested that the issuance of a revision and elaboration of Information Circular 7311, The Hazards of Hydrogen Fluoride Poisoning in the Mineral and Allied Industries, which hay been out of print for some time, would be opportune. Fluorine minerals have been known since the Middle Ages. Fluorine was isolated in 1886 by Moisson (2).

Jan 1, 1954

By L. W. Scott

This report presents an overview of explosionproof (X-P) enclosure research being conducted by the Bureau of Mines, This report emphasizes the increasing importance of research related to the safety con- siderations of X-P enclosures used in underground coal mines. Selected topics are included that summarize results of research in the areas of electrical clearances, reliability of enclosures with windows, safety factors in X-P enclosures, potting materials, performance tests for X-P enclosures, protection against high-voltage explosions, and innovative X-P devices.

Jan 1, 1985

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1978 and 1979 was 8831.8 million and $336.4 million, respectively. In 1978, nearly all commodities registered an increase in production and value; unit value increased for all commodities, with the exception of native asphalt and sand and gravel. Alabama led the Nation in the production of crushed marble and was second in bauxite, third in masonry cement, kaolin, native asphalt, and oyster shell, and fourth in bentonite, dimension marble, fire clay, and scrap mica. Trend; and Developments.-The Alabama State Docks at the Port of Mobile handled more than 10 million tons of bulk material in fiscal year 1978; volume dropped slightly to 9.8 million tons in fiscal 1979. Bulk materials comprise the major activity at the facility, with iron ore and bauxite being two of the major materials handled. The movement of these ores is vital to the operation of many heavy industries in the State.

Jan 1, 1981

By D. Gearhart

Full-scale tests are conducted on mine roof supports using protocols developed by the National Institute for Occupational Safety and Health (NIOSH) using the unique capabilities of the Mine Roof Simulator (MRS). These protocols simulate the loading conditions that the support will be exposed to in an underground mine to determine the performance capabilities and limitations of the support. Some tests are conducted with rigid boundary conditions, creating uniform contact and near ideal axial loading conditions. These tests are used to determine the ultimate performance potential of a support, including the strength, stiffness, and stability. For prop supports where stability is a critical design issue, tests are implemented to induce buckling by a modified end condition, eccentric contact, or biaxial loading. It is important to determine the cpacity of the support design when the support is subjected to unpredictable loading conditions. This paper examines the effect of end conditions and load profiles on prop support performance and applies a new analysis methodology based on eccentric loading to determine a factor of safety for load capacity. Recommendations for installation practices that minimize eccentricity and therefore preserve capacity are also provided.

By C. J. Chindgren

Upgrading of commercial red cake and recovery of vanadium oxide from uranium-vanadium mill solutions were investigated by the Bureau of Mines. Alternative procedures potentially useful for manufacture of high-quality vanadium oxide at the mill site were explored and developed. The simplest and best procedure for converting commercial red cake containing about 10 percent combined sodium and potassium oxides (Na20) (K20) into a 98- to 99-percent vanadium pentoxide (V205 product appeared to be a metathesis in an ammoniacal solution of ammonium sulfate. Molybdenum, as well as the alkali metal oxides, was removed from the red cake by this procedure at a modest expenditure of labor and reagents. When preparing vanadium oxide of higher grade, it was necessary to dissolve the red cake and reprecipitate the vanadium as ammonium metavanadate. Calcination at 450° C, decomposed the metavanadate and yielded oxide of about 99.5 percent V205. By recyrstallizing the metavanadate before decomposition, an oxide product approaching 99.9-percent purity was obtained.

Jan 1, 1962

By R. M. Gooding

This paper presents a short history of the production of mineral-energy fuels and energy from waterpower in the United States, with brief discussions of the utilization of each of the fuels and hydropower, and a look at fuels competition and interchangeability. Basic data, in figures and tables, are brought together in this publication for the production of coal in the United States from 1800 to 1960, for crude petroleum, natural gas liquids, and natural gas from 1859 to 1960, and for hydropower since 1900. Production for each segment of the fuels complex in the principal producing States from 1946 to 1960 is shown. Data are not included for consumption as such or for imports and exports.

Jan 1, 1963

By C. Melvin Lepper

To provide the U.S. mining and energy industries with information in the selection of seismic detectors for high-resolution applications, the Bureau of Mines evaluated 35 velocity detectors (geophones) and 9 accelerometers. It was found that velocity detectors with natural frequencies from 10 to 100 Hz were effective for seismic studies in the 5-to 600-Hz spectrum and that accelerometers were most effective in the 100-to 1,000-Hz range. Although the accelerometers described in this report performed about equally with the better velocity detectors tested, the accelerometers showed higher output voltage levels at higher frequencies, which is an advantage. It is important that a seismic detector and its intended purpose be matched properly to achieve the intended results in high-resolution applications. There are many factors that could affect proper matching, thus careful selection of the best detector for a particular application must be exercised.

Jan 1, 1981

"A coordinated, integrated research effort aimed at studying the scientific, engineering and medical aspects of the respirable dust problem is underway in the areas of dust generation, dust dispersion and dilution, dust characterization, interaction of dust and lungs, and relationship of seam characteristics to dust generation and mobility. (FIGURE 24) The Center's research program explores these concerns with the objective of refining existing strategies and developing new respirable dust control techniques that are consistent with the dust-lung interaction processes that lead to mine worker disability. The fundamental aspects of this work are applicable to the control of respirable dust problems in both hard rock mines and coal mines and to other dusts such as diesel-generated.Research projects in the Generic Mineral Technology Center for Respirable Dust have effected several improved methods for the preparation and characterization of the dusts needed by these projects. Superior procedures for generating ""standard"" dust samples have been developed and are in regular use in the laboratory. Questions raised during the course of some projects regarding ""stale"" versus ""fresh"" dust have led to the development of sampling techniques where the dust is directly collected in a surfactant. MSHA and CANMET have requested and received information on Center generated software. An equipment manufacturer, TSI, Inc., requesting input on modifying the inlet of an aerosol sampler has been assisted as a result of research that was conducted at the University of Minnesota.The objectives, scope and progress of all the research projects in the Center, in the form of abstracts and reports, have been detailed in Volume 1 of this series. Research papers written by the principle investigators and resulting from the findings of projects (FIGURE 25) and which are funded by U.S. Bureau of Mines grant number G1135142 have been published in Volumes 3 through 6 and Volume 8 of this series. Volume 2 relates the cooperation and interaction of the U.S. Bureau of Mines and the Generic Mineral Technology Center for Respirable Dust in research on the problem of respirable dust in the mineral industries."

Aug 31, 1989