Search Documents

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of the significant coalbeds of Clarion County, Pa. Of the 15 samples collected, 1 was of metallurgical quality as received, 4 could be sufficiently upgraded to provide acceptable products, and the remaining 10 samples could not be upgraded to metallurgical quality because their sulfur contents could not be lowered to meet the standard. For steam or power generation, 1 sample was of low sulfur content as received, 1 sample could be upgraded to low sulfur content, and 10 samples could be upgraded to medium sulfur content. The original sulfur content of the remaining three samples can be appreciably reduced by removal of the sink 1.58 specific gravity material; however, these coals would be classified as medium sulfur coals both before and after removal of the sink material.

Jan 1, 1968

By F. S. Wartman

This paper gives an account of the production of ductile-grade titanium powder in 100-pound batches by reduction of purified titanic Chloride with magnesium, grinding, leaching, and magnetic-separation of the reaction product. Apparatus, technique, and methods of controlling product quality are described and some data on operating costs are given.

Jan 1, 1949

By A. B. Coates, J. E. Crawshaw

"The use of such methods and apparatus as the Dautriche method and the Mettegang recorder for the determination of the rate of burning of black blasting powder and other strictly burning explosives has been found to give such erratic results that no reliance can be placed on the data thus obtained. Consequently, investigators of those factors which may affect the burning rate, such as size of grain, absolute density, chemical composition, and means of ignition have had to rely mainly on observations made during practical use for determination of the part played by each. Such tests are very difficult of interpretation.The purpose of this paper is to describe a method used by the explosives division of the Bureau of Mines for the investigation of such explosives and to present the results of an investigation using that method.The investigation was concerned with the effect of grain size, initial pressure, and means of ignition on the rate of burning or rate of pressure development of black blasting powder as compared with pellet powder.The Bichel pressure gauge was used for these tests, with the slight modification to the apparatus and method described in U. S. Bureau of Mines Bulletin 15.4 These modifications consisted of reducing the speed of the revolving drum on which the time-pressure record is taken, measuring the speed of the drum by a belt-driven tachometer, and introducing an induction coil in series with the electric squib or electric detonator to mark on the time pressure record the instant at which the squib or detonator was fired."

May 1, 1929

By H. E. Powell

Magnetic susceptibilities were determined by the Bureau of Mines fur 19 cobalt- and nickel-bearing minerals and for a suite for synthetic cobalt-nickel diarsenides analogous to the rammelsbergite and safflorite series. Relations between susceptibility and composition were found to be nonlinear for both impure natural minerals and pure synthetics.

Jan 1, 1967

By J. H. Welsh

This Bureau of Mines report presents guidelines to be considered in the design, installation, and operation of environmental mine monitoring systems in underground coal mines so as to enhance safety in the U.S. mining industry. A review of the current status of mine monitoring in the United States is also provided.

Jan 1, 1987

By D. K. Ingram, P. Jurovcik

The National Institute for Occupational Safety and Health (NIOSH) identified hearing loss as the most common job-related disease in the United States in its 1996 National Occupational Research Agenda. Previous studies by NIOSH have shown that operators of surface drill rigs without cabs are commonly exposed to A-weighted sound levels exceeding 90 dB. During hammer-drilling, A-weighted sound levels exceeding 100 dB were recorded at the operator station. NIOSH collaborated with a local drilling company to design and install a partial cab between the operator and the drill steel in an effort to reduce the sound level at the operator station. Sound level measurements in the field show the partial cab reduces the A-weighted sound level by 5 to 9 dB at the operator’s left ear and 2 to 5 dB at the operator’s right ear while hammer-drilling. This paper briefly discusses the preliminary design of a cab and the testing of materials for construction of the prototype. An explanation of the ideas behind the prototype design and fabrication are covered. Finally, the field test method and results are discussed in detail.1

By J. D. Davis

THE carbonizing properties of one medium- and and five low-volatile coals from West Virginia and one high-volatile A and two medium-volatile coals from Pennsylvania were determined by 800° and 900° C. BM-AGA carbonization tests and expansion tests in the sole-heated oven. Plastic properties of the coals and the yields and quality of their cokes and other carbonization products were determined. The low-volatile coals comprised a mine and a coke-plant sample of Pocahontas No. 6-bed coal from the. Black Eagle No. 1 mine, Wyoming County, W. Va.; a mine sample of Pocahontas No. 6 bed from the Louisville mine, Mercer County, W. Va. ; Davy Sewell bed was sampled at the Twin Branch mine, McDowell County, W. Va.; and Fire Creek bed was sampled at the Dunedin No. 1 mine, Raleigh County, W. Va. The medium-volatile coals were from the Fire Creek bed, Laurel Creek mine, Greenbrier County, W. Va.; Lower Kittanning bed, Springfield No. 4 mine, Cambria County, Pa.; and Upper Kittanning bed, Springfield No. 6 mine, Clearfield County, Pa. The high-volatile A coal represented the Upper and Lower Freeport beds, Kent Nos. 1 and 2 mines, Indiana County, Pa. In addition to the coals listed, high-volatile A coal from the Pittsburgh bed, Warden mine, Allegheny County, Pa., a standard blending coal, was used in blends in this investigation.

Jan 1, 1950

By F. N. Kissell, J. Kohler

Proper measurement of dust particle concentration is a critical step toward the elimination of dust-related occupational disease. This paper examines the development of dust sampling methods in U.S. coal mines, with emphasis on the benefits of personal sampling and on recent developments that permit real- time assessment of dust exposure.

By J. B. Gayle

Although heated circuits frequently have been employed in the conditioning stases of certain flotation processes, particularly the flotation of fluorite, the control of temperature is not generally considered economically feasible for the flotation of coal. This viewpoint, although widely held, can neither be substantiated nor refuted by reference to published data. Some evidence is available, however, that temperature is an important variable in the floatability of coal as well as other minerals. For example, Gayle and Swelley4 found that contact angles for coal and related substances were definitely dependent on temperature. Bailey and Whalan5 showed that changes in pulp temperature may exert a pronounced influence on recoveries of coal in batch flotation tests. The present laboratory-scale investigation was undertaken to obtain information about the effects of changes in pulp temperature on coal flotation recovery and also on the selectivity of separation possible using different reagents. The results indicated that flotation recoveries were markedly affected by temperature variations when certain reagents, particularly simple aliphatic alcohols, were used. For other reagents, particularly kerosine, flotation recoveries were substantially independent of variations in pulp temperature. Release-analysis results indicated that temperature variations did not greatly affect the selectivity of separation possible with the reagents tested.

Jan 1, 1961

By Guy A. Johnson

Despite the use of warning alarms to alert miners to the backward movement of large mining equipment, miners still are injured too frequently in backup accidents. Currently approved backup alarm technology consists of continuous sounding alarm systems. New technology has developed a warning system that initiates an alarm only if there is an object close behind the vehicle. This advancement eliminates constant exposure to the alarm because a warning is given only in case of a potential collision. Adoption of this development can improve safety and reduce damage, especially for front-end loaders (FEL's). It will also eliminate a source of nuisance noise in urban and residential areas. This Bureau of Mines report describes the general characteristics of infrared (IR) light, ultrasonic wave, and Doppler radar technology as used for backup alarms, and reviews the testing of the most promising detection devices.

Jan 1, 1986

By John W. Thatcher

A demountable X-ray tube vacuum spectrograph was designed by the Bureau of Mines for the determination of long-wavelength X-ray spectra from the light elements. This instrument was operated for both secondary and combined primary-secondary excitation of the aluminum K-series. There was an increased analytical sensitivity for elements in period 3, and an indication that with improved X-ray tubes or direct election excitation of the sample, X-ray determination of elements in period 2 is also possible.

Jan 1, 1965

By R. V. Lundquist

Past reports by the Bureau of Mines have described the extraction of alumina from numerous aluminum silicate materials by the lime-soda sinter process. The results from pilot-plant investigations of six materials, with alumina-to-silica mole ratios from 0.3 to 8.7, indicated a relationship between the alumina-silica ratios and the processing characteristics of the sinter. A series of laboratory tests was conducted to define this relationship. Sinter and leach tests determined that an alumina-to-silica mole ratio of 0.90 or greater resulted in the best alumina and soda recoveries while leaving the leach slurries practically free from any tendency toward gelation. The widely different chemical and mineralogic properties of the various aluminous materials used in compounding the mixes had no perceptible effect on the leaching characteristics of the sinter. The blending of low-cost, high-alumina materials with aluminum silicate materials to give an alumina-to-silica mole ratio of 0.90 or greater would improve alumina and soda extraction and minimize operating problems in the lime-soda sinter process.

Jan 1, 1970

Locating subsurface conductive solutions is important for many applications, including in situ mining and environmental protection. Drilling boreholes for sampling is expensive and can increase contamination by mixing water from different aquifers. Various noninvasive geophysical methods are available, but previous comparisons were hampered by different methods being used at different sites or at different times. The U.S. Bureau of Mines (USBM) compared methods at one site using the same conductive solution to improve the reliability of the comparisons. Locating deep (> 100 m) solutions is most difficult, SO the USBM selected methods applicable for such depths. Objective Improve the ability to locate subsurface conductive solutions by evaluating and comparing applicable geophysical methods. Approach The experiment was performed cooperatively with other agencies to increase the number of methods studied. The USBM, the University of Arizona, Sandia National Laboratories, and Zonge Engineering and Research, Inc., conducted cooperative field tests of six electromagnetic (EM) geophysical methods to compare their effectiveness in detecting salt water brine of conductivity 3.6 S/m collecting at the water table, 157 m subsurface. The brine was injected through two boreholes. The test site was the University's San Xavier experimental mine near Tucson, AZ. Geophysical surveys using surface and surface-borehole, time-domain electromagnetics (TEM); surface controlled-source audiofrequency magnetotellurics (CSAMT); surface magnetic field ellipticity, surface-borehole, frequency-domain electromagnetics (FEM); and crosshole FEM were conducted before and during brine injection. A total of 110,000 I. of brine was injected over one week, but the effective target volume of brine was much smaller because of mixing with ground water and dispersion.

Jan 1, 1994

The Bahamas Oil Refining Co. (BORCO) refinery in Freeport continued to operate at less than half its full 500,000-barrel-per-day capacity. Although owned through subsidiaries by the Carey Energy Corp (65%) and Standard Oil Co. of California (35%), BORCO is ineligible for participation in the Crude Oil Entitlements Program granted to companies operating within the United States proper or its territories. Like some other Caribbean refineries, BORCO has suffered a loss of normal market outlet due to the wt advantage afforded U.S. refineries by the Entitlements Program. Saudi Arabia, Nigeria, and Libya are the major suppliers of crude for the refinery. Its principal products, motor spirits, aviation fuel, distillate fuels, and residual fuel oils, were marketed in the United States and Puerto Rim. The Government-owned Bahamas Development Corp. and Burmah Oil Co. Ltd., held discussions pertaining to a renegotiation of Burmah Oil's management contract for the Grand Bahama Oil Transshipment terminal. The desired contract modifications were not made public but financial problems have plagued the terminal and its operation since construction started in 1972.

Jan 1, 1981

By E. L. Garton

[The oil-producing district, "Southern Oklahoma," is generally considered to be that part of the: State lying; southwest of the Arbuckle Mountains. It includes six counties: Carter, Cotton, Garvin, Jefferson, Kiowa, and Stephens. At present cost of the oil is produced from formations of Pennsylvania age. The individual crude oils resemble those produced in other parts of the State, except that the sulfur content is rather high. This report is a continuation of a study of Oklahoma crude oils3/ being made, by the Bureau of Mines, Petroleum Experiment Station, Bartlesville, Okla. in cooperation with the State of Oklahoma. Analyses are given of 27 samples obtained from 21 fields in the southern part of the State, end the physical and chemical characteristics of these crude oils are discussed briefly. Analyses of crude oils from other Oklahoma areas and publications in which these analyses may be found are listed in tables 2 and 3.]

Jan 1, 1941

By Jeanne A. Zimmer, Charles D. Taylor, Edward D. Thimons

Strategies for monitoring methane levels during roof bolting in an extended cut entry were evaluated. Testing was conducted at the Pittsburgh Research Laboratory’s methane test gallery. Operating conditions were varied and methane releases at the face and drill holes were simulated. Methane readings were taken at the face, and at locations outby the face. Results show that, when the major source of methane was at the drill holes, the highest methane readings were at locations on or 6.1 m (20ft) inby the bolting machine. Methods for selecting better outby sampling locations, when the majority of the methane is released at the face, are examined. During roof bolting it is easier to sample at these outby locations rather than at the face. Further testing is needed to determine what relationship exists between methane concentrations at the outby locations and at the source of the methane release.

By M. R. Yenchek

The U.S. Bureau of Mines has determined a method for calculating coal mine portable power cable thermal life for a specified temperature loading. This work was the culmination of a multifaceted research project involving (1) accelerated life tests of insulation and jacket materials and (2) steady-state and cyclical loading of cables. Composite Arrhenius curves were derived for common insulation and jacket materials to identify the key cable quality that precipitates thermal failure. Plots of temperature rise versus current for popular cable sizes were then referenced to develop a correspondence between cable life, based upon thermal degradation and current loading. Predictions of cable thermal life were made through integration over variable load cycles and, consequently variable operating temperatures. This procedure may have utility for both the U.S. Mine Safety and Health Administration and mining machine designers in determining the appropriate cable size for new equipment.

Jan 1, 1991

By John Furness Park

This paper, which describes the mining methods and practices at the Jarbidge mines of the Elkoro Mines Co., is one of a series of papers being issued by the United States Bureau of Mines on mining methods and costs in various districts throughout the United States. LOCATION AND HISTORY The Elkoro Mines Co.'s property is located at Jarbidge in the northeast corner of the State of Nevada (fig. 1). The camp is 9 miles south of the Idaho line; the nearest railroad point is 70 miles to the northeast at Rogerson, Idaho. A road leading to the south and connecting with Deeth, Nev., is passable during the summer months; the heavy snowfall which generally takes place early in the winter usually closes the road until the first of July.

Jan 1, 1931

By Frank E. Cash

The Bureau of Mines in its safety work has for a number of years advocated and recommended the use of permissible portable electric cap lamps for use in all mines. In the course of time required for the evolution from an unsatisfactory to an efficient and safe light, but encouraging increase in their use has been experienced in Alabama. As early as 1916, small installations of these safer lamps were made or an experimental basis by several operating companies, and the first complete mine installation eras made at the Virginia mine of the Gulf States Steel Co., July 1, 1918. From the experiments in 1316 and the complete equipment of the first mine in 1918 gradual progress has been made until there are now 30 installations with 10 operating companies; as a result 20 mines have been put entirely and 5 partly on, closed lights, and 3 companies equip their engineering departments; two installations of closed lights are maintained by other companies for emergency use. One of the mines partly on the electric cap lamp is an ore mine - the only one in Alabama (and one of the very few in the United States) that uses closed lights. ACKNOWLEDGEMENTS The full cooperation of operating officials, lapmen, and lamp representatives was given in the collection of the data in this report, and is hereby acknowledged.

Jan 1, 1928

By D. N. Nilsen

The U.S. Bureau of Mines investigated the use of unsupported liquid emulsion membranes (LEM's) for the extraction of copper from relatively dilute aqueous solutions (=0.3 and 2.5 g/L Cu), The performance characteristics of the three main unit operations of an LEM circuit (emulsion generation, metal extraction, and emulsion breaking) were assessed in laboratory-scale batch tests. In single-stage extraction tests using 2.5-g/L Cu feed solution, emulsion membranes extracted up to 94 pct of the copper from solutions without pH adjustment and 99.7 pct when the pH was maintained at about 2.5. Simulated two-stage crosscurrent and countercurrent circuits extracted all but 3 and 4 ppm of the original copper content, respectively. Extraction data from solutions containing mixtures of metals indicated a strong preference for Cu2+ extraction when oxime-type extractants were used in the LEM; however, some coextraction of Fe 3+ and Zn2+ was experienced. An electrostatic coalescer was used to break the copper-loaded emulsions for separation of the component phases. Up to 96 pct of the contained stripping solution (internal solution) containing the extracted copper was separated from the organic phase of the emulsion membrane. The recovered organic phase was recycled without apparent problems.

Jan 1, 2010