Search Documents

By A. R. Rule

This report describes preliminary studies by the Bureau of Mines to develop a procedure for extracting the fluorine from low-grade fluorspar ores in which the CaF2 particles are finely locked in the calcite matrix. A combination of flotation beneficiation and pyrohydrolysis is applied to recover and to liberate the fluorine. Flotation of a finely locked high-calcite fluorspar ore containing only 11.7 pct CaF2 recovered over 92 pct of the fluorspar at a grade of 51 to 52 pct CaF2. Pyrohydrolysis of the flotation concentrate liberated nearly 90 pct of the fluorine as aqueous HF. By this procedure over 80 pct of the fluorine contained in the original ore was extracted.

Jan 1, 1974

By Robert B. Fisher

[The purpose of this paper is to acquaint manufacturers of various types of asbestos product's, particularly those that specialize in materials used for sound deadening, vibration damping, and filtration, with a recently invested depth deposit of paligorskite, a type of asbestos usually called mountain leather. In the past this mineral has been only a museum curiosity but it possesses characteristics that may adapt it to industrial uses. The deposit is on Lemesurier Island, near this entrance to Glacier Bay, in the northern portion of southeastern Alaska, at approximately latitude 58° 17? N., longitude 1360 05' W. The island is about 4 ½ miles in east- west length and miles in width. The property on which the deposit occurs is owned by the locator Joe Ibach, end it was brought; to the attention of the Bureau of Mines by Col. George B. Norris. A Bureau of Mines engineer, accompanied by the owner and Chris Ellingen, visited the property sand examined the open-cuts from May 7 to 10 in 1944. The purpose of the examination was to determine the approximate extent of the occurrence and to obtain samples of the material for identification end study of its utilization.]

Jan 1, 1945

By Forrest T. Moyer

Injury experience at metal mines and mills (excluding officeworkers) in 1964 was 60 fatal and 3,672 nonfatal disabling work injuries during an exposure time of 149 million man-hours worked. These injuries occurred at a frequency rate of 24.57 per million man-hours and had a severity rate of 3,687 days lost or charged per million man-hours. Employment at 2,363 metal mines and 291 mills, excluding officeworkers, was 68,140 men in 1964. The average number of days worked was 274 The principal cause of fatal injuries at all mines and mills was haulage accidents and in underground mines, only, was falls of ground. The principal cause of nonfatal injuries was handling material accidents. The frequency rate at metal mines and mills in 1964 was slightly below that of 1963, whereas the severity rate was higher. Injury experience at 94 primary nonferrous smelters, refineries, and reduction plants (excluding officeworkers) was 8 fatal and 999 nonfatal disabling work injuries during a worktime of 98 million man-hours worked. The combined injury-frequency rate in 1964 was 10.29 and the injury-severity rate was 1,005. The 36,956 employees worked an average of 329 days during 1964. The principal cause of injuries at these plants was handling material accidents.

Jan 1, 1968

By James W. Ballard

The facts are generally accepted that an atmosphere containing large quantities of any dust is objectionable to breathe and that some dusts are more dangerous than others. Therefore, knowledge of the com-position of dusts is important in evaluating the hazard entailed on exposure. At present, free silica, of which quartz is the most abundant form, is considered one of the most significant dusts, from the standpoint of pneumoconiosis, and one State5/ has established permissible limits of air dustiness on the basis of the free-silica content of rock. The amount 06 free silica in materials used for rock dusting also has been limited.6/ Determination of free silica or quartz, therefore, is important.

Jan 1, 1940

By Charles Findlay, Stephen Krickovic, J. E. Carpetta

As one of its projects for degasification of major panels of coal prior to mining within them, the Bureau of Mines conducted methane emission studies during development of a set of three headings 1,800 feet in a major coal panel (2,700 by 3,500 feet) which had been completely isolated by sets of main headings for 12 months in the Federal No. 2 mine (Pittsburgh coalbed) in northern West Virginia. Similar emission studies were conducted in the development of two sets of main headings in virgin coal areas nearby. Comparing the two sets of data indicated that the isolated coal panel had been degasified by approximately 70 percent.

Jan 1, 1973

By William A. Beck

This report describes the loading and transportation practices employed at the zinc-lead mines of The Eagle-Picher Co., Jo Daviess County, Ill., and Lafayette County, Wis. The report also gives a brief history of the Illinois-Wisconsin zinc-lead district and the operations of the company in the area. The diesel-powered, rubber-tired loading and haulage equipment is described and illustrated from the operational point of view only, and an analysis is made of the materials-handling system without going into health and safety factors. The costs per ton of the various components of mechanical loading, underground haulage, underground crushing, and hoisting for fiscal year 1960 are tabulated.

Jan 1, 1964

By R. H. Jefferson

This Bureau of Mines report describes a series of rapid wet chemical methods for the analysis of blast furnace slags. A "complete" analysis for total iron, manganese, silica, lime (calcium oxide), magnesia (magnesium oxide), sulfur, and mixed oxides (R203) can be routinely performed in less than 3 hours. These methods were employed as the analytical control procedures for the Bureau's experimental blast furnace operations and have been satisfactorily applied to the analysis of other slags and calcareous materials.

Jan 1, 1974

By G. L. Gates

The Bureau of Mines studied the scales formed in producing wells in the Wilmington field, California. The scales were primarily barium sulfate and resulted from the mixing of injected sea water and formation waters; there was excess sulfate in the injection water and the formation waters contained appreciable barium. After breakthrough, the produced brines were supersaturated with barium sulfate. Laboratory tests indicated that barium sulfate precipitated quickly When the supersaturated brines were agitated with crystals of barium sulfate and fairly rapidly when more sulfate solution was added. Precipitation occurred slowly on standing or under nonturbulent conditions. Both the apparent and equilibrium solubilities of barium sulfate in these brines were determined and compared with equilibrium solubilities in distilled water and sodium chloride solutions.

Jan 1, 1965

By K. J. Miller

A laboratory electrophoresis column was designed to separate pyrite from fine coal by utilizing an observed difference in the electrophoretic mobilities of the two materials in water. The apparatus worked well when tested with synthetic mixtures of coal and pyrite, but some modifications in design and procedure were necessary to provide a sharper separation. After these changes were made, the column was tested with a high-pyritic-sulfur raw coal sample. The column successfully fractionated the sample, removing not only the pyritic refuse, but a siliceous refuse as well. The invest ion demonstrated on a laboratory scale that pyrite and other impurities can be separated from fine coal by electrophoresis.

Jan 1, 1970

By N. S. Petersen

As part of the Demand Evaluation Program of the Bureau of Mines to determine future needs for minerals, a study was instituted to develop and describe a methodology for approaching the problem of substitution between mineral commodities and between mineral commodities and other materials. The report comprises three sections: A review of general factors relative to substitution, a case study of the effect of substitution on zinc die-casting markets in recent years, and a general methodology for reviewing materials substitution with specific emphasis derived from reviewing substitution in the domestic zinc die-casting markets.

Jan 1, 1971

By R. T. Johansen

A gradual decrease in injection rates commonly occurs as a water-flooding project becomes older. This decrease can be attributed to changes in reservoir conditions, such as swelling of clay minerals, fillup, or gradual plugging of the sand face. However, a rapid decrease in the rate of injection indicates abnormal behavior and is cause for alarm. Extreme plugging conditions can completely stop injections into a formation. Such behavior in wells was the main concern of the tests described in this report. An accepted method of alleviating this condition is by backflowing input wells - closing the supply lines to the wells and allowing the reservoir pressure to force water back into the wellbore and to the surface. If backflowing is not successful, a string of smaller diameter pipe sometimes is run inside the casing, and the sand face is flushed with a waterspray. More drastic treatment is to inject acid into the wellbore to dissolve extraneous matter, or even part of the reservoir material, in an attempt to restore the permeability of the sand immediately around the wellbore. Any of these procedures can he coordinated with bailing and swabbing of the well for cleanout purposes.

Jan 1, 1957

By B. K. Shibler

During the investigation of the occurrence of manganese deposits in the Western United States, examining engineers of the Bureau of Mines collected 2-ton samples from five manganese properties near Golconda, Nev. Extensive laboratory tests were made to determine the amenability of these ores to standard ore-dressing methods of concentration. The Tom Major property, one of those sampled, is situated 12-1/2 miles south of Golconda, Humboldt County, Nev. The deposit is described as a bed about 5 feet thick in a thinly bedded shale and dolomite formation. The sample tested was obtained from the manganese bed, but the examining engineer reported: "The mining of an appreciable tonnage at reasonable cost would perhaps cut in half the grade represented by the sample."

Jan 1, 1951

By Terry L. Muldoon

The Bureau of Mines conducted an investigation to quantify microphone response variations that could result when the microphone is worn by a worker, as with a personal noise dosimeter, and to suggest an optimum placement and orientation of the microphone for noise exposure measurements. Previous studies have shown no significant variations in a diffuse field. This investigation, therefore, was conducted in the free-field conditions of an anechoic chamber using an anthropometric dummy as a subject, and broad band noise as the acoustic stimulus. This investigation established that, in a free field, the wearer's body does significantly affect microphone response; the response variations are a function of azimuth, and location and orientation of the microphone. Results suggest that locating the microphone on top of the subject's shoulder, oriented parallel to the body axis, should yield data comparable to that obtained using a sound-level meter.

Jan 1, 1973

By Jueun Lee, Jong-Hwa Yoon, K. Rider, Bernard J. Martin

Whole body vibration is known to affect movement accuracy [1], however little is known about changes in the organization of movement and movement strategies used to limit the influences of perturbations. The specific aim of this work is to analyze the motion and coordination of upper body segments of seated operators performing reaching tasks under whole-body sinusoidal vibration exposure and simulated vehicle ride motion. The long-term objective is to model reach coordination and predict the dynamic behavior of the upper body motion under vehicle vibration exposure. Method The reach task consisted of pointing with the right hand index finger to targets located on touch screens placed in front of the subject, 45° overhead and 90° to the right in the mockup cabin of an HMMWV placed on a 6 DOF ride motion simulator. The task was performed under stable (no vibration) and vibration (sinusoidal vibration or simulated ride motion) conditions. A motion capture system was used to record kinematic data of reflective markers to recreate body link trajectories. Joint angles (torso, shoulder and elbow; Figure 1) were then computed using quaternions. Coordination between body links was defined as a) the joints angle-versus-angle relationships between the upper arm and lower arm, and b) the joint motion onset relationships between torso, upper arm and lower arm in the time domain. Results Angle–versus-angle relationships. The relationship between upper arm vs. lower arm angle and torso vs. upper arm angle for a far forward reaching movement in the stable (solid lines) and vibration conditions (dotted lines) are illustrated in Figure 2. Fig 2A compares the control condition with a 4 Hz lateral vibration while Fig 2B compares the control condition with a 6 Hz vertical vibration. It appears that under vibration exposure the reduced upper arm extension is compensated by an increase in torso flexion. This effect is seen in the last phase of the movements (encircled areas). In addition, the lower arm extension is delayed under 6 Hz vertical vibration (Fig 2B left panel). Time of joint motion onset. The timing relationship between torso, upper arm and lower arm is largely a function of the target to be reached. Examples of delays between body links are illustrated in Figure 3. The control condition is compared to a 6 Hz vertical vibration for three

Jan 6, 2006

By E. F. Ferrell

The Bureau of Mines, U.S. Department of the Interior, studied the use of manganese sea nodules for catalytic oxidation in air of 1 pct carbon monoxide, 1 pct propane, and 1 pct methane. Catalysts were prepared from both Pacific Ocean and Atlantic Ocean nodules and compared with a platinum catalyst using a fixed-bed, steady-state microreactor with gas chromatographic analysis. Combustion temperatures with manganese nodules were 50° to 100° C lower than those with the platinum catalyst. Ion-exchange addition of rare-earth promotors to the nodule catalyst decreased combustion temperatures an additional 5° to 45° C.

Jan 1, 1978

By Harold Bailie

The purpose of this Bureau of Mines report is to furnish information on mining practices applied to flat-bedded fluorspar deposits in southern Illinois. It presents new and improved operating procedures and specialized techniques applicable to deposits of this type. All of the operating mines of the Ozark-Mahoning Co. in this area have been opened by vertical shafts which connect with levels consisting of haul-age ways, stopes, and loading stations. The stoping practice used locally called room and pillar, is open stoping with pillars left at different distances and diameters. To facilitate haulage and drainage, the mines are worked from openings turned off the main haulage drift on a grade to conform with the dip of the ore beds. The ore is predominantly fluorspar with smaller amounts of galena and sphalerite that contain traces of cadmium and germanium. The principal gangue minerals are limestone, calcite, shale, barite, and sandstone. The rock hardness ranges from relatively soft shale to hard, abrasive sandstone.

Jan 1, 1960

By R. D. Saltsman

Under contract with the Federal Bureau of Mines, Bituminous Coal Research, Inc., performed a statistical study to find less expensive and time-consuming methods of monitoring the noncombustible content of coal mine dust. Calculations based on thermodynamic considerations verified the reasonableness of Federal rock-dusting requirements. The results of extensive sampling in southwestern Pennsylvania mines indicated that, at the 95-percent confidence level, the present system of sampling at 200-foot intervals may be replaced by sampling at 500-foot intervals, and that a 1-inch scoop floor sampler may replace the standard 6-inch scoop for floor sampling. Further field testing is recommended.

Jan 1, 1975

By T. Bieniawski

"INTRODUCTION The Congress theme ""Improvement of Mine Productivity and Overall Economics by Modern Technology"" is probably beat: addressed by the subtheme allocated to this Plenary Session. It is appropriate that .Theme 1 emphasizes the simple point that effective use of geotechnical information is the key to improving mine productivity. In essence, this means that: (1) geological and geomechanics, (rock mechanics) data must be collected in sufficient quantity and of high quality; (ii) data interpretation must be performed specifically for purposes of engineering design; (iii) innovative design approaches should be used to bring about Improvements in productivity and safety.While, each of these three aspects .may: seem obvious to any mining engineer it is a fact that the above sequence is seldom followed and as a result, mining engineering not infrequently lags, behind other branches of engineering when it comes to design creativity, efficiency and safety.. . After all, mining is still-one of the most hazardous occupations and we are gathered here to discuss, at the highest world professional forum, how to use more effectively the modern technology. This however, does not mean that mining engineers are less capable than other engineers or that their achievements are any lesser; far from it! Mining engineers are the cream of the engineering society on whose efforts depends the welfare of mankind. Moreover, they have produced minerals and coal evergrowing quantities against evergrowing difficulties. Yet, we must and can become even better because we are not making full use of the modern technology and rock mechanics knowledge already at our disposal, and. we are not being innovative enough to the full extent of .our capabilities."

Jan 1, 1989

By Lisa Steiner, Robin Burgess-Limerick

In 2004, underground coal mines in the United States reported 3,405 injuries to the U.S. Mine Safety and Health Administration (MSHA). Of these, 17 percent were associated with the use of bolting machines, 8 percent with continuous miners, and 4 percent each with scoop/load-haul-dump (LHD), shuttle cars and personnel transport. Analysis of the injury narratives identified five hazards that required attention. They are rock falling from supported roof inadvertent or incorrect operation of bolting machine controls, handling continuous miner cable, collisions while driving underground vehicles and driving or traveling in underground vehicles on rough roadways. The rate of lost-time injuries has steadily decreased during the past 10 years (from more than 10 per 100 FTE in 1995, to six in 2004). However, underground coal mining remains a hazardous industry. One of the contributors to this elevated injury risk is working with or near underground coal mining equipment. Roof bolting machines and continuous miners have been consistently identified as high risk equipment. They account for approximately 24 percent of all injuries to underground coal miners (Sanders and Shaw, 1989). LHD's, shuttle cars and personnel transports are also associated with injuries in underground coal mines (Burgess-Limerick, 2005). Conventional analyses of injury statistics typically provide tables detailing the breakdown of injuries by body part nature of injury or mechanism of injury. Such analyses are worthwhile and may be helpful in tracking broad trends over time. Further information is available in the narrative text field completed for each injury reported. The detail contained in these narratives varies. However, they generally provide some insight into the causes of the injury, such as the activity being performed at the tune of

By Yumi Nakashima, Setsuo Maeda

Vibration magnitude and frequency of the z-axis vehicle seat are time-variant, which are influenced by not only vehicle vibration characteristics themselves but also road surfaces, speeds and the human body. There is little in the current reporting about evaluating and analyzing automobile seat vibration that focuses on the time-variant. Yaguchi et al.1 has proposed a method to evaluate automobile seat vibration that is based on judgments using a subjective mental state. Their method focuses on the time-variant magnitude of the peak frequency on a power spectrum density. However, their method has no consideration of all the frequency contents of the discomfort, nor comparison between different peak frequency vibrations. Suzuki2 has emphasized that the vehicle vibration should be judged by a series of vibration stimuli to evaluate, because the vehicle vibration is time-variant, which isn’t a matter of the relationship between a single vibration stimulus and a subjective response. He clarified that the human sensation to the vehicle vibration discomfort changes every moment showing the relationship between the frequency-weighted r.m.s. acceleration calculated every 5 seconds and the category judgment to vehicle vibration discomfort every 5 seconds. However, his study doesn’t show what parameter connects to the subjective final judgment to vehicle vibration. Therefore, we applied the method similar to ISO100563 considering the time-variant to the vehicle seat z-axis vibration evaluation. The new method for the vehicle seat vibration considering the time-variant was examined on the hypothesis that the final subjective evaluation must be conducted from the judgment summarizing a series of vibration stimuli. Methods The vibration bench system, which reproduces the movement of a vehicle floor, was used for the experiment with the single-axis (vertical direction) four-post road simulator system, which is usually used for a car, as shown in Fig.1. The experiment was done on the right side of the vibration bench using the floor vibration which was 5.5 minutes, 0.822 m/sec2 (Wk) over the range 0.5-20Hz with 4 male subjects (age ave21.5, SD0.5, weight ave75kg, SD7.91kg, height ave166.8cm, SD5.2cm) and 4 suspension seats. As Fig.2 shows, subjects evaluated the degree of discomfort every 5 seconds to each seat vibration measuring the seat z-axis vibration acceleration. [ ]

Jan 6, 2006