Search Documents

By Eric J. Foell

Recognizing that the planned commercial exploitation of polymetallic nodules in the deep sea should be accompanied by environmental studies in order to protect this largest and least understood ecosystem of our planet, the German Ministry for Research and Technology has since 1989 funded a longterm and large-scale disturbance-recolonization (DISCOL) experiment in the abyssal Peru Basin of the equatorial South Pacific Ocean. The circular study site is located at 4150m depths and encompasses about 10km2 of relatively flat, heavily sedimented sea floor with low (< 15%) nodule coverage near an existing German nodule mining exploration license area. The RV SONNE, a large and well-equipped multi-purpose research vessel, served as platform for all environmental cruises conducted to date. The initial DISCOL expedition (SO-61, Feb.-March 1989) was carried out in two legs. During DISCOL 1/1, a study site was selected, a pre-disturbance baseline assessment was undertaken, and sea floor disruption was begun using the "plow-harrow", a uniquely designed disturber device towed repeatedly across the circular study area. During DISCOL 1/2, disturber deployments continued until the device had created 78 criss-crossing and partially overlapping tracks along which nodules were essentially plowed under while sediment from up to 15cm below the seabed had been turned over and exposed at the surface. In addition to the obvious within disturber track impacts, sediment mobilized by plowing drifted off with the prevailing near-bottom current and redeposited downstream, blanketing nearby areas not directly disturbed. Immediately after the disturbance phase, an initial post-impact sampling series was performed. The DISCOL Experimental Area (DEA) was revisited about six months (DISCOL 2, SO-64, Sept. 1989), three years (DISCOL 3, SO-77, Feb. 1992), and seven years (ATESEPP SO-106, Jan.-March 1996) after disturbance to collect further post-impact samples, monitor changes in the benthic community and follow the recolonization process. In addition to benthic community studies, plankton investigations were initiated during the third DISCOL cruise (SO-77) and continued during three further cruises (SO-78, SO-79 and SO-80/2) in 1992.

Jan 1, 1996

By Kristian Drivenes, Steinar L. Ellefmo, Kurt Aasly, Ben Snook, Przemyslaw B. Kowalczuk, Rolf Arne Kleiv

"Since Ellefmo et al. (2014) published resource estimates of undiscovered seafloor massive sulfides (SMS) on the Arctic Mid-Ocean Ridge (AMOR), there has been an increased focus on establishing new knowledge about exploitation technologies for such deposits. This also includes understanding the process mineralogical properties of typical SMS deposits.The part of the AMOR that lies between Jan Mayen and the Svalbard Islands and is located within Norwegian jurisdiction and, as such, investigating the potential for mineral production from hydrothermal vent fields has been seen as strategic. The AMOR has been explored for active hydrothermal vent fields since early 2000s (Pedersen et al., 2010b). One of the active vent fields discovered, Loki´s Castle, is located in the northern part of Mohn´s Ridge. This vent field was first described by Pedersen et al., (2010a) and consists of two mounds, each approximately 100-150 m diameter and 20-30 meters high, hosting several active chimneys, up to 11 m high.Loki´s Castle has been selected as a case site in order to study the properties of typical SMS occurrences with respect to possible future deep-sea mining activities. As part of the MarMine cruise in 2016, the Loki Castle was visited and sampled for e.g. mineral characterization and mineral processing analyses. In total, more than 500 kg rock samples were collected using ROVs, and intended for further research (Ludvigsen et al., 2016). In addition to sampling mineralized rock fragments, survey data like bathymetry, magnetics and Underwater Hyperspectral Imaging (UHI) was collected using Automated Underwater Vehicle (AUV)."

Jan 1, 2017

By William D. Siapno

Mining the deep ocean by the year 2000 may seem far fetched. The year 2000 is but a decade away, a scant 10 years. Remember, the youngsters of today will grow up in a little more than a decade and rebut the wisdom of the ages, especially the traditions of their elders. Rude perhaps, but none the less a fact of life. Ocean mining exhibits many of these same traits. We should all brace ourselves for some rude shifts in our rapidly moving society. Major shifts in economics, politics, and social orders are the rule of the day. Communism is in retreat, our own economic structures chaotic. So in this moment of cataclysmic change, a shift in the international market place of mineral resources should not be a great surprise.

Jan 1, 2011

By Steven D. Scott

Several polymetallic sulfide deposits (copper, zinc, f lead, silver, f gold) presently exposed at the surface of the ocean floor are of sufficient size and apparent grade that they will someday be seriously considered as mineable resources. Responsible ocean mining may have some real environmental advantages over land mining, although they both share the same downstream problems caused by smelting and refining. The area of disturbance for an ocean mine would be much less than for an equivalent sized deposit on land around which considerable rock has to be excavated in order to get at the ore. Acid mine drainage, a very serious problem in land ming, would not be a concern in the alkaline and oxygen deficient environment of the deep ocean. There would undoubtedly be loss of habitat for some marine organisms but this could be minimized by mining deposits that are no longer hydrothermally active and therefore support little life. The risk of severe corrosion and thermal damage to the mining equipment at hydrothermally active sites would probably preclude their recovery in any event. The scientific community and environmental advocates should take advantage of the long lead time before ocean mining commences to insure that the environmental mistakes of the past, as encountered in some land mining, are not repeated. In order to fully understand and thereby mitigate the consequences of recovering seafloor sulfides, test mining of a small deposit using the German-designed high capacity television grab, preceded and followed by detailed observations of the mining site from a submersible, is proposed.

Jan 1, 1992

By Brian D?Olier

Much of the aggregate that is being exploited at present from these areas is a ?relic? deposit. It was originally eroded from primary source rocks and transported to a depositional centre by processes that are now either greatly reduced in effectiveness or are largely absent at the present time. Following the retreat of the Devensian ice sheet, the subsequent rise of sealevel and the drowning of large areas of the continental shelf along with the lower reaches of many rivers, a fresh sequence of sediment sources, pathways and sinks now exist. Sediment is being eroded from several, pre-existing source areas and transported along different, well - defined pathways to a number of new depositional sinks. Some of the present, licenced, aggregate dredging areas lie close to these sources, pathways and sinks with the consequent dredging activity being perceived by some as interfering with the ?natural process? that links the offshore and the coastal / littoral zones. With this perception in mind, the principal, sources, pathways and sinks between Flamborough Head and Beachy Head will be highlighted and the relationship of dredging activity upon them, evaluated. It will be demonstrated that offshore dredging activity has no effect upon supplies of sediment to coastal beaches.

Jan 1, 2004

By Carlos Almeida, Bruno Matias, Stef Kapuskiak, Eduardo Silva, José Miguel Almeida, Alfredo Martins

Underwater intervention operations have been supported by robotic systems such as remotely operated vehicles (ROV) for a long time. In particular challenging scenarios such as the deep sea, the use of ROV systems for environment awareness is in fact the main tool of choice. With the technical advances in autonomous robotics, there is an increased effort in substitute ROVs whenever possible for autonomous underwater vehicles (AUV). These systems don't have tether and thus provide large advantages from the operations and logistic point of view. However the limited options for underwater communications render them impracticable for many tasks were real time environment awareness and direct human control is needed. Emerging applications in underwater mining, both at sea [1] and in inland flooded mines [2] pose additional requirements in terms of operation support needs and environment restrictions. Two main tasks are to be addressed by assisting robots in these underwater mining operations: providing adequate environment awareness for human operators and obtain precise realtime 3D environment modelling (particularly relevant for the mining planning). The use of ROVs with umbilical cable, has in this case large limitations due to the nature of the mining cutting (performed by dedicated systems) that limit manoeuvrability and pose high risk of cutting the cable or damaging the vehicle. In this paper we present EVA (Exploration VAMOS AUV) an innovative hybrid ROV/AUV system developed for operations support in inland underwater mining operations. This robot is always operated without tether, and the can be used in a wireless ROV tele-operation mode using very short range high bandwidth underwater communication systems and in autonomous AUV mode.

Jan 1, 2018

An extensive ferromanganese nodule field south of New Zealand (Fig. 1) has existed beneath the flow of the Deep Western Boundary Current (DWBC) and Antarctic Circumpolar Current (ACC) for at least the past 15 m.y. West of 174°E, between 59°S and 48°S, the field is 300-500 km wide, but east of 174°E, where current flow impinges on the eastern slope of the Campbell Plateau, the field narrows from ca. 200 km at 55°S to ca. 120 km at 51°S. This narrowing coincides with deflection of current flow eastwards, and consequent reduction in bottom-current velocity and eddy kinetic energy. Based on sea floor photographs, dredge samples and 3.5 kHz profile data, six distinct seafloor substrates are delineated, forming broadly parallel zones eastwards from the lowermost Campbell Slope (Fig. 2).

Jan 1, 2003

By Peter Halbach

Hydrothermal activity is well known from many locations on most mid-ocean ridges, however no hydrothermally mineralized area had yet been found at the ultraslow spreading southwest Indian Ridge up to October 98 when the Japanese RV Yokosuka with the submersible Shinkai 6500 investigated this area. A massive sulfide field was discovered near 27º51S / 63º56 E in the 11th segment west of the Rodriguez Triple Junction. The Free University of Berlin had joined this cruise and taken over the responsibility for the study of the respective sulfide mineralizations. Hydrothermal minerals were sampled during two dives at water depth of about 2940 m close to the summit of an axial volcanic ridge called Mount Jourdanne. There massive sulfides occur on the seafloor as small smooth mounds with an average area of about 5 m2. Their surfaces are weathered and have a reddish to brownish colour. In addition to these mound-like structures, small tube-like chimneys were observed. These chimneys rise approximately 30 to 40 cm above the floor and are less than 10 cm in diameter. No indications of hydrothermal fauna could be detected. All the hydrothermal features are spatially related to faults and smaller fissures controlled by an E-W trending graben system crossing the summit region of the submarine volcano. Such tectonized areas are generally considered to be ideal for hydrothermal activity because they may have both a magmatic heat source in the deeper underground and pathways for fluid circulation, respectively.

Jan 1, 2001

By Odyssey Marine Exploration

Odyssey is a world leader in marine exploration and has undertaken expeditions in varying environments throughout the world addressing many commercial and regulatory demands. Odyssey works in a variety of settings such as shallow coastal territorial waters, abyssal plains in exclusive economic zones, and high seas in international waters on projects involving mineral exploration, environmental analysis, oceanographic survey, and recovery operations. Odyssey Marine Exploration (Odyssey) excels in adaptively managing programs from initial concept through realization of commercial goals while successfully satisfying the regulatory and engineering demands of deep sea projects. This poster presentation reveals best practices throughout a project life cycle and presents case studies in areas including but not limited to: • Research practices to identify and define valuable subsea resources • Project planning and licensing to achieve project goals and meet regulatory requirements • Optimizing offshore operations to achieve desired results • Designing projects to support processing and commercial programs

Jan 1, 2018

By Sang Bum Chi

In order to better predict and manage benthic disturbance by deep seabed manganese nodules mining, we needed to conduct a benthic disturbance experiment at the selected area, which has a similar environmental condition as the preservation reference area. Therefore, we have performed environmental baseline studies from 2003--not only to select the benthic environmental impact testing site but, also to detect any environmental changes before and after mining activity. Since then, a large dataset of various parameters ranging from physical (e.g. temperature, salinity, current, weather), chemical (e.g. dissolved oxygen, nutrients, dissolved and particulate organic carbon), biological (e.g. bacteria, plankton, benthos), geological (e.g. Mn-nodule abundance, sediment shear strength) and others (e.g. bathymetric profile and slope, mass flux) have been accumulated. Using this dataset, descriptive statistics and cross-correlations were performed to select the benthic environmental impact testing site. Outcome of this analysis suggests that the potential benthic impact testing site would be a rectangular-shape area (10 km × 10 km) and located at 10°27&apos;~10°33&apos;N, 131°53&apos;~131°58&apos;W, which is latitudinally the same as the preservation reference area.

Jan 1, 2011

By Kiseong Hyeong

The Intertropical Convergence Zone (ITCZ), where the southeast and northeast trade winds converge, is the effective climatological barrier that separates the southern and northern hemispheres in terms of dust budget. Asian and N. American dusts dominate in the Pacific north of the ITCZ, while Central and S. American dust prevails south of the ITCZ. In order to understand the nature of latitudinal and depth-related variations of mineral composition in terms of position relative to the ITCZ, deep-sea core sediments were collected from 9°N to 17°N at a 2° intervals along the 131.5°W meridian and analyzed for mineral composition. The amount of illite in surface sediments decreases gradually from 65% at 17°N to 31% at 9°N. In contrast, smectite increases from 11% to 56% southward. The observed mineralogical variation toward the ITCZ is attributed to the increased supply of volcaniclastic material transported via the southeast trade winds from the Central and South America source regions. Smectite-illite transition, a phenomenon that the amount of smectite increases over illite, occurs at around 10°N, the northern margin of the ITCZ. This result indicates that the change in latitudinal position of the ITCZ in the geological past could be recorded by the smectite-illite transition in deep-sea cores. The cores studied show down-core variation of mineral composition from illite-rich at the surface to a smectite-rich clay suit at depths, similar to the latitudinal variation. The smectite-illite transitions observed in these cores are likely the records of changes in latitudinal position of the ITCZ. The depth and age of the smectite-illite transition is getting shallower and younger towards the equator, implying that the ITCZ was located farther north during late Tertiary and has shifted southward to the present position of 5°N~10°N.

Jan 1, 2004

By Alexander Malahoff

An international research team working through the Hawai?i Undersea Research Laboratory (HURL) undertook a bold challenge to explore the chemistry, geology, mineral formation and superheated hydrothermal vents of the Kermadec Island Arc. With the mothership, R/V Ka?imikai-o-Kanaloa, scientists from six research institutions explored the active submarine volcanoes stretching over a line of volcanoes 1,000 miles long between Samoa and New Zealand. The expedition left Hawaii on the 18th of March 2005 and returned on the 5th of August having covered a distance of 10,000 miles between Hawaii and New Zealand. Scientists from the USA, New Zealand and Germany used the HURL submersibles, Pisces IV and Pisces V, as well as the remotely-operated vehicle RCV-150, aboard the R/V Ka?imikai-o-Kanaloa to dive into active volcanoes to water depths of 2,000 meters. Scientists from New Zealand, the USA and Germany conducted 41 dives on the previously unexplored (from manned submersibles) submarine volcanoes. Ten active volcanoes were explored during this time. Hundreds of specimens of new and unusual marine life, water chemistry, extremophile microorganisms, mineral formations and volcanic rocks were collected during this expedition with the two submersibles and the ROV. Bizarre natural events, such as the oozing of hot liquid sulfur from the ocean floor onto the skids of the submersible were observed. Carbon dioxide gas was observed profusely streaming into the seawater from the volcanoes, making these one of the greatest contributions to hot house gasses entering the atmosphere.

Jan 1, 2005

By M. E. Williamson

A seafloor based robotic drilling system is being developed for the National Institute of Ocean Technology in Chennai, India to support a National initiative for marine methane hydrate research. The system will be capable of core sampling to 150m below the seafloor in 3000m of water under telemetric control of an operator onboard a research vessel at the surface. Unlike previous robotic drilling systems, this unit (designated the ACS) will use wireline methodology to reduce the number of tool handling operations required to complete the borehole (conventional rod drilling requires 2025 tool handling operations to complete a 100m hole, while wireline requires only 48 operations to reach the same depth).

By Hal Palmer

A number of Articles contained in the United Nations Convention on the Law of the Sea III (UNCLOS) bear directly on legal issues related to the recovery of mineral deposits on the ocean floor. Mineral resources of the continental margin other than oil, gas and hydrates include, sand, gravel, shell, coral, gemstones and phosphorite. Jurisdiction over the exploration and exploitation of these deposits is determined either by the Territorial Sea claims of a coastal state or their recognized sovereign rights in the Exclusive Economic Zone (EEZ). At least 33 coastal states have the right under Article 76 (Continental Shelf regime) to claim seabed jurisdiction beyond 200 nautical miles (EEZ limit). In addition, several states have "Pioneer Investor" status with regard to seabed resources in international waters (The Area). A global maritime boundary database (GMBD) has been developed as a basic resource identifying the current claims of coastal states. It provides detailed information on existing boundaries and limits determined by the UNCLOS accords or by multi-lateral agreements which affect mineral exploration and exploitation. This paper will describe the GMBD and its construction and maintenance.

Jan 1, 2000

By James M. Franklin

Research on modern hydrothermal systems provides quantitative measures of the processes of formation of hydrothermal fluids and of precipitation mechanisms from them. Studies of ancient deposits provide new information regarding volcanological processes that are related to the deposits, as well as data on their spatial and temporal compositional variations. Mew exploration guidelines result from both aspects of research. The most fundamental requirement for large metalliferous hydrothermal systems is an abundant heat supply for the upper two kilometers of the crust. This heat may come from a focused heal source (shallow-level subvolcanic intrusion), but ambient heat also may have provided enough energy for the reactions necessary to effect leaching of metals, especially where heat flow is particularly high (i.e. very large or high-temperature magmatic source, such as ultramafic environments). For most VMS systems, the majority of the metals were derived through leaching from footwall strata; in addition interstratal fluids may enter subvolcanic intrusions during episodes of magma a chamber "cracking," engendering some &apos;?magmatic" component in the hydrothermal system. Direct contributions of metalliferous magmatic fluid also may be significant from arc-related or back-arc felsic or alkalis systems. These latter contributions may form exceptionally high - grade portions in some deposits. Subvolcanic intrusions, which are excellent indicators of high heat flow and may have been the direct driving mechanisms for some stems undergo two stages of alteration: On intrusion emplacernent. fluids may rapidly enter and react with their mesostatic portions, evident in the sills in the Middle Valley. High temperature interactions caused albitization and destruction of oxides and sulfides, releasing metals. During terminal hydrothermal stages, the metalliferous fluid collapsed into the intrusions, forming disseminated and vein sulfides.

Jan 1, 1998

By J. A. Jankowski

The situation in the raw material market has brought into consideration the commercial exploitation of the mineral deposits on the deep sea bed and in particular the manganese nodules. They occur generally in depths of 4000-5000 m, partially covered or buried in bottom sediments. The deposits and their potential recovery have been intensively explored and researched during the past twenty years (Bischoff 1979, Halbach 1988, Padan 1990). Although the present market situation limits the rentability of deep sea mining on an industrial scale, the mining technology is being further developed in many countries. The stagnation phase in the deep mining issue allows sufficient time for conducting research on the precautionary protection of the deep sea environment and for consultation in the development of technologies with the least possible impact on it. The subject has gained in importance since autumn 1994, when the United Nations International Law of the Sea was signed. This also regulates human activities in international waters from the environmental point of view. As fields tests have shown in the past, even with the most modern technologies, mining of the manganese nodules will inevitably be accompanied by a resuspension of some bottom sediments. The generated sediment plumes will be further transported with the ocean currents and in the worst case form stable turbidity layers in different depths (Ozturgut 1981a, Baturin 1991). One of the problems of the environmental impact assessment is the estimation of the plume persistence before it eventually dilutes to approximately the ambient concentration level or settles at the bottom (Lavelle 1981a, Lavelle 1981b, Lavelle 1982, Thiel 1991a, Thiel 1991b). The aim of the research is to develop a numerical sediment transport model in connection with potential manganese nodule mining in a reference area located in the southeastern equatorial Pacific Ocean off Peru (Peru Basin, Discol Experimental Area). In this region, a German mining claim is registered and interdisciplinary field works of the TUSCH (German: TiefseeUmweltSCHutz, deep sea environmental protection) research group are carried out in order to obtain the required scientific background for evaluating of the deep sea mining impacts and to provide the necessary supporting data for the modelling (Thiel 1991a, Thiel 1991h).

Jan 1, 1995

By E. Moriguchi, K. Tamaki, A. Okuda, K. Iizasa, C. Honsho

The northern Izu-Ogasawara Arc is characterized by an abundant distribution of submarine calderas along the volcanic front to the back-arc rift zones. In many of these calderas hydrothermal activities are observed. Among these calderas, hydrothermal ore deposits with economically feasible quality and amounts are hosted at two calderas, the Myojin Knoll Caldera and Beyonnaise Knoll Caldera. We conducted two research cruises in 2005 and 2006 to investigate further hydrothermal activities and ore deposits in these calderas and to complete the geological and geophysical mapping in the area. We discovered a strong signature of hydrothermal activity in the Myojin-sho Caldera using AUV capabilities. Newly obtained geological and geophysical data clarified the relationship between back-arc rifting tectonics and hydrothermal activities in the area. Five calderas (two of them newly found) and numerous (>200) volcanoes are mapped in the area. Complete SeaBeam coverage showed a distinct feature of the back-arc rifting activity and its relationship to the submarine calderas on the volcanic front. The back-arc rift zones composed of four segments separated by E-W trending volcanic ridges. Three of the calderas are located in the rift zone and are heavily deformed by the rift normal faulting that typically trend NNW-SSE. As the Beyonnaise Caldera is located in a swarm of faulting zones at the eastern end of the back-arc rift, the formation of the hydrothermal ore deposits found in the Beyonnaise Caldera are apparently affected by these faulting activities. Newly found submarine calderas are located in the rifting zone and are heavily faulted.

Sep 24, 2006

By Georgy Cherkashov

Shallow-water formation of marine ferromanganese nodules as well as their deep-water analogues is found throughout the global ocean. The Baltic Sea is a key province for the shallow-water type of marine minerals. The following main distribution areas of Fe-Mn nodules have so far been discovered in the Baltic Sea: the Gulf of Bothnia, the Gulf of Riga, Central Baltic area (Gdansk- Klaipeda) and the Gulf of Finland. The last area (Gulf of Finland/Finnish Bay) is the best studied from all aspects including geological prospecting and environmental assessment.

Sep 14, 2011

By Randolph A. Koski

Recent investigations located at least six major massive sulfide deposits (dimensions measured in tens to hundreds of meters) within a 50-km-long segment of Escanaba Trough, the sediment-covered axial valley of southern Gorda Ridge. The sediment fill is intercalated silt and sand turbidites and hemipelagic mud with a maximum thickness of 500 m. Several volcanic edifices, spaced at approximately 15-km intervals along the ridge axis, penetrate and locally breach the sediment. The largest sulfide deposits form mounds and ridges on the steep flanks of structurally unstable sediment-capped blocks that have been uplifted above the volcanic edifices; both sediment and sulfide deposits are undergoing rapid erosion and redeposition. Although hydrothermal activity appears to be absent at most sulfide fields, 220°C fluids are discharging from the tops of sulfide mounds near 41°00&apos;N lat, 127°31&apos;W long. Recent pillow lavas and sheetflows erupted onto the sediment-covered sea floor less than 500 m away from the active vent field. The massive sulfide deposits have compositional characteristics that differ from deposits formed on sediment-free spreading axes. The Escanaba Trough deposits include Fe- and Cu-rich, Zn- and Pb-poor massive sulfide mounds, polymetal (Zn-Fe-Pb-Cu-As-Ag-Sb-Sn) sulfide vent structures, abundant barite-rich chimneys, crusts, and sinter cones, and thermogenic petroleum in the sulfide and sediment. Sulfate-rich crusts have high Au values ranging between 2 and 10 ppm. The unusual mineral assemblage at Escanaba Trough

Jan 1, 1989

By Raymond A. Binns

In this first sub-seafloor examination of an active hydrothermal system hosted by felsic volcanic rocks at a convergent plate margin, we drilled 13 holes altogether, achieving deep cored penetrations at two sites. Our aims were (1) to delineate the lateral and vertical variability in mineralisation and alteration patterns below the PACMANUS hydrothermal site near the 1650-1700 m-deep crest of Pual Ridge in the eastern Manus back-arc basin, so as to understand links between volcanological, structural and hydrothermal phenomena, and (2) to establish the nature and extent of microbial activity within the system. Technological innovations vital to success included our precise location of holes on small targets with drill-stem video, the use of a new hard-rock re-entry strategy, and deployment of casing with a new hammer drill. Other technical achievements were the first ODP application of an advanced diamond coring system, and the first direct comparison in a hardrock environment between structural images obtained by wireline methods and by logging-while-drilling (resistivity-at-bit).

Jan 1, 2002