Search Documents

By Emad Farouz, Ehab S. Shatnawi, Charles Winter

The increasing demand for small deformations and high-capacity drilled shafts without enlarging drilled-shaft diameters has motivated the development and increased use of a base grouting (BG) technique. This technique has been demonstrated to improve drilled-shaft axial capacity, especially for shafts tipped into loose cohesionless soils. To date, there are a couple of documented design methods for estimating the axial geotechnical resistance of base-grouted shafts. However, there is no or lack of research that addresses the lateral response of such shafts. A base-grouted drilled shaft test program was carried out during the design phase of the Wisconsin I-94 Zoo Interchange reconstruction project. The test program included installing and testing one base-grouted shaft and one ungrouted shaft under both lateral and axial loading. Based on test results, it was concluded that the lateral behavior of the BG drilled shaft is significantly stiffer than conventional drilled shaft . Hypothetical method was developed to account for potential increased, however, the method should be verified with more lateral load test.

By Antonio Marinucci, Robin Mao

The new Hangzhou West Railway Station, which is currently in the early stages of construction, will be located in the city of Hangzhou, China. To accomplish the ambitious goals of the project, the construction work and station building was divided into three project areas. The original design utilizes 1,580 drilled shafts with diameters of either 800 mm or 1000 mm (32 or 40 inch) to support the new Station and its various ancillary structures. The drilled shafts will be tipped into the moderately weathered argillaceous siltstone a distance between 5 and 15 m (16.5 and 49 ft), resulting in an effective pile length ranging from 35 to 43 m (115 to 141 ft), respectively. For the first phase, approximately 550 production drilled shafts will be installed. Eight (8) sacrificial drilled shafts each with a diameter of 1000 mm (40 inch) were installed to a depth ranging from 50 to 57 m (164 to 187 ft), and were tested to confirm the design parameters used for the first phase, to evaluate the contractor’s installation means-and-methods, and to provide guidance whether redesign is warranted for the subsequent two phases. Bi-directional static load testing was performed using a donut-shaped Super Cell to apply unidirectional axial loads up to 13,200 kN (2,970 kip). This paper will describe the bi-directional testing and select results obtained therefrom. The axial compressive and uplift resistances determined from the testing verified that the available axial resistance of a single drilled shaft exceeded the minimum design requirements.

By Matthew Runion, Christopher Lawler

The Aeolus – Jim Bridger Transmission Line Project is located in southern Wyoming, home to some of the largest coal seams in the world. Coal seams present unique challenges to underground construction, as they are at high risk of coal-seam fires and do not provide a reliable bearing stratum. Accurate identification of these hazards was essential for reliable design and successful construction of foundations on this project; however, environmental restrictions and other protections created short time frames to access several sites. Coupled with a firm construction deadline, this meant that a comprehensive geotechnical investigation prior to construction would not be possible. This paper presents the project as a case study, and details how an Engineer-Procure-Construct (EPC) contracting format supported by a comprehensive Quality Assurance (QA) program provided a solution to the defined challenges. It describes the initial design process using incomplete geotechnical data and explains how the developed QA program verified design assumptions and reduced geotechnical risk through early identification of geologic conditions during construction. Specific examples will be given, and industry implications will be discussed.

By Clarissa Aguiar, Seok hyeon Chai, Thamer Yacoub, Sina Javankhoshdel

Sheet piles are used as an excavation support for soil retention. They are interlocked systems to form a wall for earth support along with anchors to provide an extra lateral support in excavations. The earth pressure against a sheet pile structure is not unique for each soil, but rather a function of soil-structure system. Movements of the structure with respect to the soil are primary factor in developing the pressure and thus the problem becomes indeterminate. In order to model a sheet pile wall for the analysis, structural element/interface can be used for the sheet pile. However, the use of the structural element with soil model alone is insufficient to simulate this soil-structure system as it fails to capture the slip condition between the sheet pile and the retained soil. In order to capture this slip condition, an interactive element can be used between sheet pile and soil to allow slip to occur. There have been many case studies where this method was used to analyze the response of the retained soil. Numerical studies have shown a good agreement with experimental results, but this stiffness is often not a well-known parameter, due to its complexity in nature of interactive behavior between soil and sheet pile walls. Also, many case studies are carried out with twodimensional analysis of the foundation, where three-dimensional analysis may be more suitable in some practical applications. In this paper, the interactive behavior of the element between sheet pile and soil is investigated with case studies for staged excavation using sheet piles and anchors. Then, investigation of a three-dimensional model is carried out by comparing with two-dimensional analysis.

By Dave Paul

Dam rehabilitation involves a range of design, construction, and operation risks, some of which are not encountered in new dam construction. These risks can have significant impact on project schedule and project budget. Owners, engineers, and contractors need to understand these risks. Existing dams typically were designed in an era of design and construction standards that have been upgraded and changed. Modern standards will impact the construction approach taken and involve understanding the earlier standards. Knowledge of historical standards/practices as well as current design standards and construction methods is valuable for developing and designing rehabilitation components. Construction records and as-built drawings are valuable when they are available. Rehabilitation projects often consist of older projects where as-built documents or construction records are not available. Where these records exist, many (most) times, they do not fully reflect the current conditions within the dam and appurtenant works. leading experienced practitioners to “expect surprises” both during investigation of the existing facility, as well as during construction. “Surprises” should be expected even when historical records of investigations, design and construction are available. Unknowns, be they known unknowns or unknown unknowns, can be planned for by developing an approach for the design and construction process to identify potential issues/problems, or at least alert the designer and contractor of potential issues. A Risk-Based approach applied for the entire life of the rehabilitation project can be used to alert the parties of potential “surprises” and provide direction for mitigating issues as they arise. This type of approach is particularly effective when the process includes senior practitioners with decades of design and construction experience in all aspects of dams. Minimizing impacts created by “surprises”, particularly during construction, can result in an improved project meeting budget and schedule goals and design standards. This paper identifies and categorizes risk types salient to dam construction, reviews the process of risk identification and analysis, discusses guidelines for risk allocation, reviews strategies to mitigate risks, presents several case studies where risk mitigation strategies were employed successfully (or unsuccessfully), and presents lessons learned. The paper concludes with a summary and recommendations for best practices for Project Risk Management and mitigation that can be used by: Owners; Design Engineers; and Construction Managers, in planning, design, pre-construction and construction phases of dam related projects.

By Robert L. Goehring, Fred Munene

This case history for three major additions to a tire manufacturing plant in north Georgia discusses the impact of highly variable Karst (sinkhole) geology on both foundation design and construction. For Phase 3, alternatives were considered for a heavily loaded mixing tower with up to 2,000 kip column loads. A non-traditional approach of using auger cast piles was adopted. To satisfy a risk-averse Owner, a pile load testing program including strain gauges was conducted. One test pile was cored full depth to demonstrate effective bearing on steeply inclined rock. For Phase 4, similar methodology was used at another critical mixing tower structure associated with that phase and the installation procedure was refined to reduce grout take. In Phase 5 construction, another mixing tower and the equipment pits were supported on auger cast piles. After pile installation, a sinkhole opened up between two equipment pits. Remedial grouting was performed. Development also required construction of a R&D building over a 96 inch diameter RCP storm sewer. Auger cast piles were used to support the building to avoid overstressing the existing pipe and risk separating joints. This case history outlines lessons learned while constructing auger cast piles in Karst and proving quality was built into the foundations.

By Travis Coleman, Elvis Ishimwe

Currently, more than 400 drilled shafts have been constructed by various contractors at the I-90/94 and I-290 Jane Byrne (Circle) Interchange, located near downtown Chicago, Illinois. Cross-Hole Sonic Logging (CSL) and Thermal Integrity Profiling (TIP) tests were performed to evaluate the integrity and concrete quality of the drilled shafts installed at this project. For Phase I of the project the shafts were tested using CSL methods, and the shaft integrity was identified by analyzing the First Arrival Time (FAT) and the signal strength (energy) measurements. For the major portion of Phase II, the Illinois Department of Transportation (IDOT) accepted TIP testing as a substitute for CSL at the request of the contractors. The CSL testing results indicated 54 percent of the tested shafts had anomalies, and 78 percent of these anomalies were located within the lower three diameters of the shafts. To date, TIP testing results indicated the shaft integrity was as expected and acceptable for the all 34 tested shafts. A review of the testing results and a discussion of the detected anomalies are presented. In addition, a comparison of both TIP and CSL measurements is presented in this paper.

By Richard Schmidt, Lijun Deng, Mohamed Abdelaziz, Weidong Li

Helical piles are widely used as a foundation supporting a variety of different structures. Understanding the axial behaviour of helical piles is required to confirm the engineering design. Helical pile research is often conducted in the field, but this method can be prohibitively expensive in some cases. Geotechnical centrifuge modeling offers an alternative method for the helical pile research and practice. A series of axial load tests of helical piles installed into cohesive soils were conducted on the geotechnical centrifuge at the University of Alberta. The objective was to investigate the effects of inter-helix spacing and soil strength on the axial behaviour of helical piles. Four types of aluminum model helical piles including one single-helix pile and three double-helix piles with various inter-helix spacing ratios were tested. Both compressive and tensile loading tests were conducted. All model piles were instrumented with multiple strain gauge stations. The clay had an undrained shear strength of approximately 50 kPa and 120 kPa. The test results indicate that there is a transitional failure mode between the two widely recognized failure modes, i.e., individual plate bearing and cylindrical shearing. The shaft adhesion was significantly reduced by the helix. Axial capacities were comparable to the field test results.

By Hubert Law, Amin Rahmani

This paper evaluates the effects of pile diameter on the initial modulus of subgrade reaction and proposes modifications to the subgrade reaction moduli that are commonly used in the current state of practice based on American Petroleum Institute (API) guidelines. Three-dimensional continuum finite element model of a soil-pile system is simulated under monotonic lateral loadings to develop benchmark data. The benchmark data, which includes small (0.5 ft) to large (10 ft) diameter pile responses, is used to estimate the initial modulus of subgrade reaction for each of the considered pile sizes. The study shows that the subgrade reaction moduli provided by API may underestimate the actual soil stiffness at the soil-pile interface for large diameter piles and may overestimate it for piles smaller than a certain diameter. A simple equation is proposed herein to adequately estimate the initial modulus of subgrade reaction for all pile diameter ranges. The proposed equation is validated by the measurements of full-scale field tests.

By Steve Davidow, Scott Tunison

As the demand for electric power grows and generation facilities are constructed in more remote areas, the industry faces an increasing number of foundation construction challenges. The importance of quality geotechnical information prior to construction is accentuated by the linear nature of the projects and the potential for drastic changes from one end to the other, but is often difficult or unfeasible to obtain. Alignments are crossing remote, rugged and/or environmentally protected terrain, and completing a comprehensive geotechnical program is made challenging from an access or economic standpoint, or both. In these situations, the industry needs a flexible foundation alternative. This paper will present micropiles as that alternative and demonstrate how the implementation of micropile foundations mitigated these challenges on the Koolau-Wailupe 46 kV Circuits in Oahu, Hawaii, which involved rugged, steep slopes and helicopter construction methods. It will detail the selection of micropiles over other foundation options, micropile and steel pile cap design methodologies, foundation construction, and quality control. Special attention will be given to the unique geology in the area, and why precise identification of saprolite and basalt layers was integral to the successful performance of the foundations. The intention is to communicate the benefits of a flexible solution based on continuous collaboration between design and construction.

By Waddah Akili

The demand on pile installation in the offshore of the Arabian Gulf has, over the last two decades, experienced unprecedented boom, triggered by the construction of platforms, to help facilitate the production and transport of oil and gas. Available borehole data show that ground conditions for pile installation in the offshore is highly variable, resulting in misassessment of insitu conditions, leading to a huge discrepancy between ultimate pile capacities, based on design, and actual capacities after installation. The paper makes use of pile installation records derived from several platforms in the offshore of the state of Qatar, the Gulf Region. More specifically, the paper evaluates “as–installed” ultimate capacities and safety factors, recommends remedial installation procedures, and proposes a means for determining pile acceptability for piles meeting refusal short of design penetration. The paper offers what is believed to be relevant recommendations to guide the design and installation of future offshore structures; enabling the geotechnical community in the Region to solve their current offshore pile installation problems and gain an added margin of confidence regarding the ultimate capacity of installed piles.

By Chetan D. Savani, Mike K. Muchard

The necessity to evaluate undocumented foundation lengths is essential in assessing the useable life, need for scour protection, retrofitting, or full reuse of existing bridge foundations. For this purpose, Parallel Seismic Testing (PST) has the best accuracy and is applicable to the widest range of foundation configurations used in bridge construction of any test method. Although not limited to bridges, PST case studies are presented involving two bridges. To preface the case study discussions, an overview of the PST method is given along with its results and analysis thereof. In one of the cases, we were afforded the rare opportunity to see the existing piles being extracted long after the PST testing program was completed. The resulting Class A prediction reaffirms the accuracy of the method. Versatility of the PST method is also exemplified in the two cases presented, where unique situations from complex foundation systems were overcome by analysis to provide successful results.

By Andrew Pontecorvo, Steven Lowe, David Sposito

Buildings with large height-to-width ratios require foundations with significant uplift resistance. This paper presents a case study of the permanent rock tiedowns installed for One Manhattan West, a sixty-seven-story office building in midtown Manhattan. Site access and schedule dictated the size of the equipment for installing the tiedowns would be limited to drilling a 16 inch (406 mm) diameter hole. A three bar configuration of 3 inch (76 mm) diameter high strength threaded bars was chosen to develop an allowable capacity of 923 tons (4060 kN) per tiedown. Although the quality of the rock at the site was generally high, a challenging geologic condition emerged during the installation of one of the tiedowns requiring a creative installation procedure. Although the three bar configuration performed relatively well there are challenges with loading and testing this bar arrangement. Unlike single bar tiedowns that are typically tested with a high success rate, testing of a multiple bar system can result in some unsatisfactory results. This may be attributed to the installation challenges, difficulty loading each bar uniformly and/or the method of monitoring the test. Understanding the complexities is necessary to improve the testing results and achieve similar reliabilities of single bar systems.

By Terence Ma, Seok hyeon Chai, Jeff Lam, Thamer Yacoub, Brigid Cami, Sina Javankhoshdel

The Limit Equilibrium (LE) analysis of pile-supported geotechnical structures normally assumes a constant shear force for the pile instead of considering the non-linear capacity of the pile which is related to the pile displacement. In this study, a 3D Limit Equilibrium analysis is carried out for a landslide model supported with piles by considering the constant and non-linear capacity of the pile which is computed using a separate Finite Element (FE) algorithm. The depth of the pile, soil layering, and the pile properties are used with an assumed maximum displacement to compute the geotechnical non-linear capacity of the pile. In this study, the results of the initial unreinforced 3D LE model was first compared to the 3D FE analysis results. Then, the pile pattern was applied to the failure region in the 3D LE model, and then the factor of safety was recomputed. The results of the constant shear piles were compared to the model with the non-linear piles.

Sep 8, 2021

By Michael Frawley, Deana Ruud, Jessica Turner

Technology is allowing for new ways to mitigate risk associated with subsurface exploration and unanticipated subsurface conditions during construction. Unanticipated subsurface conditions have the potential to force delays and cost overruns on even the best-managed and well-executed projects. For more than a century, geotechnical professionals have documented the location and conditions encountered in hundreds of thousands of subsurface borings. Utilizing processes for compiling and managing data, owners can streamline site selection and receive access to a conceptual geotechnical model before field exploration takes place. Digitizing historical subsurface information allows for creation of an interactive, web-based platform combining publicly available information and culminating with the opinion of a local, experienced geotechnical engineer. This connectivity aids in the reduction of risks associated with unknown conditions on prospective project sites. Through this conceptual project study, we demonstrate how a project owner would be able to use a comprehensive desktop study to review the expected conditions prior to making a purchasing decision. Following the purchase, the expected conditions would be confirmed through traditional methods, confirming potentially problematic site conditions and the associated risks. INTRODUCTION Preliminary project planning is often based on assumptions made by the design team with regards to site suitability. After due diligence, site development is traditionally initiated by the owner or the owner’s representative when engaging a geotechnical engineer to perform a thorough subsurface exploration at a site. The data generated by the geotechnical engineer’s analysis of the site is required to design foundations, pavements and earth retaining structures and move the project from concept into design. This necessary, subsurface exploration can be time consuming, intrusive, and require significant resources, often when resources during construction seasons when resources are most limited. By leveraging historical data generated from previous subsurface exploration, a more thorough analysis of project risk can be developed prior to mobilizing a drill rig. Ultimately, preliminary budgets and designs are more accurate and geotechnical field exploration is more strategic. The geotechnical engineer’s role transforms from raw exploration and analysis to confirmation of anticipated conditions.

Jan 1, 2019

By David R. Sutfin, Joseph Lodde

110 N. Carpenter is new commercial building located in the West Loop neighborhood of Chicago, Illinois. The new home to the McDonalds Corporation work headquarters, accelerated project delivery methods were essential to meet the scheduling demands for this project along with other projects slated to start in the region. As such top-down construction methods were utilized to allow for above and below grade construction to proceed in parallel in lieu of more conventional bottom-up construction methods, thus compressing the project schedule. To achieve this plan, perimeter secant pile walls were constructed in conjunction with interior columns/drilled shafts and a shear wall core constructed from inside a temporary cofferdam. The use of secant pile walls allowed for efficient accommodation of a variety of loading conditions including: exterior curtain walls loads, perimeter column loads, tower crane foundation loads, and in-plane shear loads. Furthermore, this system allowed for efficient and fluid operation of equipment on site in order to accommodate the 90-day window allotted for initial foundation construction. INTRODUCTION 110 N. Carpenter is a recently-constructed 9-story commercial building located on the old Harpo Studios property in the West Loop neighborhood of Chicago, IL. The construction of this 55,750m2 (600,000 ft2) structure is significant to the continued commercial development of Chicago as nearly 46,450m2 (500,000 ft2) of the building houses the new world headquarters for the McDonald’s Corporation, which had moved from Chicago to the suburb of Oak Brook in 1971. McDonald’s recommitment to this urban environment is not only a reinvention of the long-established fast food giant but the anchor for a broader redevelopment of the West Loop neighborhood. Since the opening of this building was seen by the developer, the City of Chicago and others as a key to future local projects, innovative solutions were required to showcase forward-thinking design as well as expedite the construction process. The final result of the design/planning process is a structure consisting of nine levels of above-grade commercial space and two levels of below-grade parking, providing approximately 300 parking spaces. The above-grade structure consists of a reinforced concrete flat plate system, including two-way slabs, columns, and two core/shear wall systems for lateral support. With an average depth of 7m (23ft), the below-grade structure consists of interior components similar to the above-grade structure (structural slabs, columns, shear walls) but includes a perimeter secant pile wall that was designed to support lateral earth pressures; vertical forces from the exterior curtain walls, perimeter columns, and the construction tower cranes; and in-plane lateral forces to reduce the demand on and quantity of interior shear walls. The use of a secant pile wall is a key component to the project because it accommodated the use of top-down construction methods to accelerate the construction schedule.

Jan 1, 2019

By Patrick J. Hannigan, Seth Robertson, Frank Rausche, Rozbeh B. Moghaddam

The Top-Loaded Bi-Directional Test (“TLBT”) and the conventional Bi-Directional Load Test (“BDLT”) are full-scale load tests where loads are applied bi-directionally to the foundation element. The BDLT uses an embedded loading source consisting of a jack assembly with one or multiple hydraulic jacks located between two steel bearing plates. As the jack(s) within the jack assembly is/are pressurized, the plates receive the load from the jack(s) and transfer these loads to the foundation element. In the case of the TLBT, the loads are also applied bi-directionally to the foundation element. However, in the TLBT case, the loading source is located above the foundation head. With the TLBT’s non-embedded and reusable load assembly, the loads are applied to the foundation using the steel shaft bearing and base bearing plates cast within the foundation. These plates are connected to the load assembly at the foundation head via Grade 75 or Grade 150, threaded, steel bars. This paper presents comparison results from a full-scale load test performed by both bi-directional load testing methods on adjacent test shafts. Details regarding subsurface conditions as well as test shaft construction and installation are included for the comparison tests. Test results and corresponding analyses are presented and discussed in detail.

Sep 8, 2021

By Patrick J. Hannigan, Frank Rausche, Rozbeh B. Moghaddam

The Top-Loaded Bi-Directional Test (“TLBT”) is a new method to apply bi-directional loads to a deep foundation element with the loading source located above the foundation head. In the TLBT reusable load assembly, loads are applied to the foundation using the R-System which consists of two stacked steel plates located at the geotechnical resistance balance point or at the foundation base connected to the load assembly via vertical elements. The top plate or the Shaft Bearing Plate (“SBP”) will transfer loads to the foundation upper portion, and the bottom plate or the Base Bearing Plate (“BBP”) will transfer loads to the foundation lower portion as well as the foundation base. At the surface, above the foundation head, a hydraulic jack is located between a Top Load Assembly (“TLA”), and the Bottom Load Assembly (“BLA”). The TLA and BLA are connected to vertical elements which are consequently connected to the R-system. As the jack is pressurized and expanded at the surface, the R-System plates are separated, and the foundation is bidirectionally loaded. This paper presents a brief description of the conventional Bi-Directional Load Test (“BDLT”) including benefits and limitations followed by the TLBT method introduction including its benefits and advantages over other testing methods.

Sep 8, 2021

By Andreas Andenæs, Arne Schram Simonsen

"AbstractThe Tresfjord bridge is with its variety in foundation concepts and difficult soil conditions one of the most geotechnically challenging projects in Norway at the time. The project comprises design of large concrete caissons, steel core piles through large rock fills, and closed end steel pipe piles in up to 40m water depth driven in very hard moraine. Test piling has also been conducted to check feasibility of the concept, and PDA measurements have been used to verify sufficient capacity of piles. FactsThe Tresfjord bridge is part of the new export road from Ålesund to Åndalsnes on the North-West coast of Norway built by the Norwegian Road Administration. The bridge will reduce travel time with about 30 min between the cities, see Figure 1. The bridge is planned to open summer 2015.The Bridge crosses the Tresfjord and will be 1290 m long. The bridge is built as a free cantilever bridge and will be resting on a total of 20 nos. of foundations, where two are abutments resting on steel core piles, three are casted directly on bed rock and 13 are foundations resting on steel pipe piles. The last two foundations holding the main span will be concrete caissons resting on bed rock and moraine. Figure 2 shows a 3D model of how the finished bridge will look. Multiconsult AS is responsible for design and pile supervision , while the Joint-Venture Bilfinger-Tresfjordbridge ANS is responsible contractor.Soil ConditionsPercussion soundings and sampling together with coring have been performed in the individual foundations using a small geotechnical equipped vessel. Acoustic and refraction seismic profiling have also been carried out to tie in the layers between the boreholes.The soil conditions are varying over the length, but are in general dominated by a soft top layer (2-4 m) of sediments over very hard moraine with occasionally large boulders. Piles in the two foundations closest to shore on the western side of the bridge are piled to bed rock with penetrations up to about 27 m in soil.Water depth varies from about 10 to 40 m for the piled foundations. Figure 3 show how the topography of the seabed varies over the bridges length."

Jan 1, 2014

By Maurizio Siepi, Paul van Horn, John Coupland, Julian Crawley

"TTMJ is the acronym for the Slurry (Diaphragm) Wall Tension Track Milled Joint currently in development as part of the European Union's innovative and far-reaching Horizon 2020 initiative (FTI Pilot-2015-1 720579). The TTMJ Project has been specifically set up to deliver this versatile new step-forward in Slurry Wall technology. The TTMJ System is protected by patent in Europe and the USA, and is currently under development by a consortium comprising Trevi SpA (Italy), Arup (Netherlands) and CCMJ Systems (UK). The principles of the TTMJ System together with the installation process are herein described in general terms. The system is still under development with field trials scheduled for early 2018, so some of the detail will not be disclosed at this stage. It is the intention of the Authors that the results of these field trials and a more complete description of the System will be presented in a paper we intend to submit for the DFI/EFFC International Conference on Deep Foundations and Ground Improvement to be held in Rome, Italy in June 2018. The final section of this paper explains how the TTMJ system can be applied to a common application of slurry wall construction; deep circular or multi-cell shafts. The system can be used to construct shafts more easily and at less cost than current methods. It also allows shafts with smaller internal dimensions to be constructed than is currently practical.INTRODUCTIONCCMJ Systems (UK) realised that an innovative new approach to forming joints in both Slurry (Diaphragm) Walls and Secant Pile Walls would provide greatly improved joint integrity to greater depths, to the overallbenefit of retaining wall quality, across the world-wide foundations industry.In particular this new system is designed to:??Increase the effective depth range of Slurry Walls (especially walls excavated by grab) and Secant Walls??Remove the requirement for Stop-ends or Joint Formers??Allow for a Shear Key at the joint??Allow for a Water Stop to be installed at the joint??Permit Continuous Reinforcement across the joint??Optimise Reinforcement Density and hence Concrete Flow??Facilitate joints in corner panels eliminating the need for “L” shaped cages and reducing largesingle-pour concrete volumes and slurry storage capacity requirements.??Enable the construction of smaller-dimensioned square and circular deep shafts (especially useful for city-centre sites) than is possible with current methods.CCMJ Systems approached other industry specialists with a view to forming a development team to explore the possibilities for this new technique."

Jan 1, 2017