Search Documents

By Lorie M. Dilley

Alaska Village Electric Cooperative (AVEC), an electric utility cooperative providing power to 51 Alaska villages, has made a concerted effort to install wind turbines in the villages they serve in an effort to mitigate the growing costs of electrical power generation. The subsurface soils in several of these villages consist of sands and silts with ground temperatures of between 30°F and 32°F. The presence of warm, degrading permafrost in three of the villages has required innovative foundation designs, including the use of helical piers and piles to support steel and concrete wind turbine foundations. The design of the deep foundations had to account for the effects of degrading permafrost likely resulting from observed climate change patterns. Uplift forces imposed on the foundations were approximately 100 kips per pile. Uplift pile load testing was conducted on the installed piers and piles in order to determine the actual working load that each pier or pile could sustain. In addition, pile driving analyzer testing was conducted on several piles installed in the permafrost and compared to pile load tests. Results indicated that the installed piers and piles achieved the necessary capacity with sufficient factors of safety. Thermosyphons were installed near the foundations in order to limit the effects of climate change on the permafrost. The two to four wind turbines in each of the three villages are currently operational. Refinement of the design based on the pile testing from the first village to the third has decreased the cost of the tower foundations and improved our understanding of designing for warm, degrading permafrost.

Jan 1, 2010

By Mark Spence, Tom Lardner, Matthew Janes

"IntroductionThe design-build method streamlines project delivery through a single contract between the Contract manager and the design-build team. The design-build method places emphasis on collaborative project management between design and construction disciplines to minimize project schedule, reduce costs, encourage balance risk amongst the design-build team. Since 1985, the percentage of nonresidential design and construction projects has increased from 5% to 45%.1A project carried out in Edmonton, Alberta, Canada will be used as an example to illustrate the challenges of the design-build project delivery method and the merits of establishing a GBR. The project involved a complex slope stabilization as part of an extensive freeway widening. At the project location the roadway was being widened within the base of a historic stream valley into a steep slope with a history of a previous slope failure. The slope was to be steepened through the installation of a series of 14 interlocking arc structures constructed half way up the slope. Access and schedule proved critical to the successful completion of the project.Geotechnique and Site HistoryThe geotechnical investigation undertaken for the site included six boreholes drilled at the crest of the slope to depths ranging from 14.5 m to 30.2 m. Laboratory testing of the soil samples included direct shear tests, Atterberg limits and grain size analysis. The geotechnical report also referenced a previous geotechnical investigation that was carried out in response to a failure of the slope in 1971."

Jan 1, 2015

By Leykam Chris J., Jacobs Scott. A.

"Construction of the New NY Bridge over the Hudson River 25 miles north of New York City is one of the largest civil infrastructure projects presently underway in the United States (formerly Tappan Zee Hudson River Crossing). The $3.14 billion Design-Build contract is also the largest ever awarded by the state of New York using an Alternative Project Delivery method, and the first major public project to use Design-Build. The new 3.1 mile long bridge will replace the existing Governor Malcolm Wilson Tappan Zee Bridge with a modern twin crossing featuring: Iconic side by side cable stay main spans; significant deck widths accommodating eight lanes of regular traffic, wide shoulders, and a shared use pedestrian and bike path; foundation with excess capacity to fully support a future rail bridge; more than 1,000 large diameter pipe piles driven in deep glacial deposits; drilled shafts installed through steep blast-rock slopes on the east shore landings. Geotechnical challenges included varied bedrock and glacial till surfaces with steep slopes and depths in excess of 750 ft.The purpose of this paper is to highlight major features of the New NY Bridge project with specific focus on the design and construction of the foundations supporting the approach and main span structures from abutment to abutment, provide background on alternative project delivery in NY, as well as provide an overview of the design-build process as it was applied to foundation delivery.The 3.1 mile Governor Malcolm Wilson Tappan Zee Bridge was constructed across the Hudson River connecting Nyack and Tarrytown (Rockland and Westchester Counties). Construction started in March 1952 and was completed in 1955 for a cost of $81 million. The seven lane crossing first opened to traffic on December 15, 1955 and coincided with the opening of a 28 mile segment of highway I-87 / I-287 between Suffern NY and Yonkers NY. The bridge is part of the extensive 574 mile New York State Thruway road system owned and operated by the New York State Thruway Authority (NYSTA)."

Jan 1, 2016

By Caciola Jr. Joseph J., Nidal M. AbiSaab

"Thanks in great part to the geology of the New York City Metropolitan area, mini-caissons are a popular choice for deep foundations. These drilled elements are readily available, easy to install with minimal impact on adjacent structures, and can be designed with large compressive and tensile capacities. Despite the frequency with which they are employed, the engineering design community is divided over several of the underlying principles governing the design of mini-caissons. This paper seeks to draw attention to several of these issues in an effort to encourage further research and discussion, namely: (1) how the allowable stresses have changed for the NYC Building Code over time, (2) the inconsistent load transfer mechanisms considered for geotechnical capacity, and (3) the role of the permanent steel casing towards structural capacities of mini-caissons.INTRODUCTIONIn the local construction nomenclature, mini-caissons are drilled deep foundation elements which derive their capacity from a socket in rock. A permanent steel casing (commonly between 7- and 24-inches in diameter) aides the drilling through overburden soils to the top of bedrock. Afterwards, an uncased rock socket is drilled into the bedrock and the inside of the casing and rock socket is inspected by means of portable video equipment. After inspection, the interior of the socket and casing is filled with steel reinforcement and concrete or grout. The casing-soil interface is generally ignored for axial design purposes and the full geotechnical compressive or tensile capacity is assumed to be generated in the rock socket. Figure 1 shows a typical mini-caisson cross section.Mini-caissons have been used for decades in the New York City area for a number of reasons. They have historically been proven to develop high axial capacities in the city’s metamorphic rock (Tamaro et. al. 2000), often exceeding 300- to 500-tons. Additionally, their method of installation (drilling) is generally able to bypass layers of dense Glacial Till, boulders, and manmade fill which would interfere with the installation of other pile types (e.g. driven piles, auger cast piles). Further they are able to extend to depths exceeding 50-ft to reach bedrock underlying a site, making them a useful tool in areas where rock is relatively deep or varied in elevation. Drilled casing installation also results in fewer vibrations and disturbances to adjacent structures and can occur in areas of restricted access (a constant concern for any project in a dense urban environment such as NYC)."

Jan 1, 2016

By Phillip E. Glogowski, N. Catherine Bazan-Arias

Steel foundations can be designed to cross-sectional configurations ranging from triangular and square to other multi-side shapes. Adding lateral extensions (hereby called wings) along the length of the steel stem can increase the foundation’s uplift, torsional and lateral load capacities. DiGioia Gray staff developed a methodology for the optimal design for multi-facetted, winged deep steel foundations. A finite element (FE) model is used to represent the steel components and the nonlinear subsurface behavior. The geometry of the foundation can be complex; thus, an optimal design needs to be fine-tuned to the specific site conditions. We created a pre-processor tool to generate the FE model including varying values for the number and size of wings, depths of embedment, reveal/stickup heights, top plate geometries, and subsurface profiles. The analytical model has been partially validated through full-scale testing and the methodology has been applied to two installed projects to date.

Sep 8, 2021

By Lucie Spencer, Craig Butterworth

"This paper presents the design of a raft enhanced pile group recently constructed for a hotel development in Perth, WA. At the time of construction in 2016 the hotel was the tallest prefabricated hotel in Australia.The structure covers the entire 12 m by 32 m development footprint, located in an inner city environment, and directly surrounded by existing structures. The small site and lack of space required innovative thinking in terms of the substructure design.The ground conditions comprise a layer of medium dense sand underlain by variable layers of stiff clay, silts and sands. Groundwater was around 1.5 m below ground level.The substructure design was carried out on the basis of a raft enhanced pile group. This allowed the use of much shorter piles than a conventional pile solution, thereby permitting the adoption of CFA piling techniques. This also allowed the raft thickness to be reduced to such that the substructure works were maintained above the groundwater level.The design was carried out in general accordance with the Australian Standard AS 2159 and using conventional piled raft design techniques involving iteration between elastic soil settlement software and structural analysis software until spring reactions were obtained with convergence of the two models. Following this springs were introduced to model piles in the structure.Due to the variable nature of the ground and resulting uncertainty in pile base capacity it was not considered appropriate to design the system as a pile assisted raft with piles loaded beyond their ultimate geotechnical design strength. As a result, all piles were designed based on a maximum load maintained within the elastic response region, with the majority of the load taken by the piles. However, the combined capacity of the raft and the piles allowed for a saving in pile lengths and numbers of around 40%, when compared to a conventional pile group designed in accordance with the Australian Standard AS 2159.The raft slab was monitored during construction in order to check the actual displacements against the design displacements. At the end of construction, the settlements were found to be within 2 mm of the design values.INTRODUCTIONThe Wellington Street area of Perth in the CBD is undergoing recent regeneration which includes the King’s Square development, Perth Arena and the Wellington Street Bus Station. The proposed hotel development is close to the recent developments on a Lot previously occupied by a low rise development. Due to the small size and constrained nature of the site, the substructure design for the tower needed to take into account available space and the impact of the works on adjacent properties. This paper presents reasoning for the choice of substructure design, details of the design methodology adopted, results from limited post construction monitoring and potential improvements that could be considered for similar future developments."

Jan 1, 1900

By Gordon Chen

As part of a value engineering envisioned by East Coast Slurry, Weidlinger Associates, Inc. designed a unique elliptical slurry wall cofferdam for construction of the 65 ft. deep MWRA North Dorchester Pump Station. A conventional rectangle cofferdam with multiple levels of bracing would have been time consuming and costly and imposed a significant obstruction to the pump station construction. A circular slurry wall, while eliminating the bracings, conflicted with adjacent structures and required excessive backfilling around the final pump station structure. The ellipse shaped cofferdam fit the needs of the project well; however, it created a significant design challenge without the use of bracings. Unlike a circular cofferdam which primarily only has hoop stresses, the ellipse still has to be designed for horizontal bending moments in each panel because of the non-axial symmetric conditions. The more eccentric the cofferdam shape; the higher the horizontal bending. The challenge was to develop a three dimensional finite element model that could analyze both the hoop stresses and horizontal bending stresses above and below the bottom of excavation induced by soil and water pressure and unbalanced construction surcharge loads. This paper discusses the techniques used to model the soils and structure interactions and results of stresses on this challenging unbraced configuration.

Jan 1, 2010

By Benjamin Jennings, Jason Herron

In the summer of 2016 Xcel Energy experienced a storm event that resulted in the collapse of approximately 8.5 miles of a 345 KV transmission line near Rogers, Minnesota. In design of the new transmission line, Xcel Energy determined that ten tower locations would be replaced with steel H-frame structures supported by helical piles instead of wood H-frame structures supported by driven wooden piles. A steel foundation was proposed for the towers due to time constraints and site conditions unfavorable to large pile driving equipment. Xcel Energy contacted the helical pile manufacturer Hubbell Power Systems, Inc. (HPS) for aid in the design of a complete steel foundation for the structure legs. With the shear, moment, and axial loads provided, the manufacturer used pile group modeling and axial capacity software to design a four helical pile group; and used 3D modeling and finite element software to design a moment resistant grillage to connect to the tower base. The steel grillage utilizes a new moment resistant connection and clamp system to transfer loads from the piles to the grillage. This connection provides a true fixed head condition and reduces lateral deflection issues typical to smaller diameter piles in pinned head connections. The clamp is designed to deform the helical pipe pile shaft and transfer the full axial load of the structure through the mechanical and friction connection. The helical piles and the moment resistant grillage were manufactured with shorter than average lead times and a helical pile installation contractor performed the installation. An expedient plan of install was developed by the contractor that resulted in an average installation rate of one complete set of tower foundations per day. The design of the moment resistant grillage, clamping system, and excellent foundation construction by the contractor provided an expedient and efficient foundation system to be discussed in this paper.

Jan 1, 2017

By David Gatto, Nicolas A. Willig-Friedrich, Jeff A. Segar

"With the increasing demand for electricity, and requirements to generate this power cleanly, more producers are turning towards hydroelectric power. A project in Iowa currently under construction will retrofit an existing Army Corps of Engineers Dam with a hydroelectric generating facility. The design of the intake structure requires the construction of a diaphragm retaining wall. The T-shaped diaphragm wall elements retain an unbalanced fill height up to 21.3 meters (70 feet). The design required a single production element be constructed, tested, and instrumented prior to beginning construction of the rest of the elements. The testing included extensive concrete mix design development, coring, and Cross Hole Sonic Logging. Installed in the other production elements are 10 inclinometers, 4 pressure cells, 4 piezometers, and multiple survey monuments. Some of these instruments require manual readings while most are monitored by an automatic data acquisition system and instantly transferred to a website providing real-time graphical display of the data. This paper will discuss the construction of the diaphragm wall from the contractor’s perspective when working on a site only large enough for two service cranes and a Hydromill excavation unit, without any storage area on the construction pad, describe the testing performed and the quality control procedures employed, and investigate the information gained from the automated instruments providing real time measurement readings.INTRODUCTIONIn 1964 the US Army Corps of Engineers (USACE) constructed a dam by raising the surface grade approximately 34.7 meters (114 feet) above the natural ground line using a combination of fill types. This earthen dam stretched slightly longer than a mile intersecting the flow of the existing Des Moines River. The center of the dam is a concrete spillway consisting of 12 monolith sections. On each end, three of the sections extend 42.6 meters (140 feet) from the spillway to transition from the concrete dam sections to the earthen dam section. Adjacent to these three sections on the East end is where the contractor is actively working, for a private developer under a lease agreement with USACE, on this site to convert it to a Hydroelectric facility licensed for an output of 36.4 megawatts, enough power to meet the needs of about 18,000 homes. To create this, a powerhouse structure, housing two vertical Kaplan turbines is being added to the downstream side of the existing dam. From the power house, two penstock pipes will be cored through the existing concrete monolith sections and connect to the Intake structure on the upstream side of the dam. Protecting and reinforcing the dam adjacent to the intake structure is a new diaphragm wall. This wall is constructed using T-shaped diaphragm elements, acting as a cantilever retaining wall for the intake platform. Figure 1 shows a diagram of the upstream features of the construction."

Jan 1, 2016

By Fabio Santillán, Mario Mauro, Raffaella Granata

"This paper presents the utilization of slurry walls methods for the recent remediation of three high hazard active dams in the United States. Tuttle Creek Dam, located in Manhattan, KS, required seismic retrofit. To this extent, transverse shear walls were installed on the downstream slope using self-hardening slurry (SHS) to reinforce the liquefiable foundation soils. Herbert Hoover Dike, located around Lake Okeechobee, FL, is subject to potential failure because of internal erosion, piping and slope instability at high water levels. The innovative use of the hydromill equipment with SHS allowed the successful construction of the cutoff wall through heterogeneous soils and rock. At Bolivar Dam, located in Bolivar, OH, under-seepage negatively affects the structural stability of the dam, and a partial seepage barrier wall is required through the upstream slope of the dam. In this case, the Contractor selected the plastic concrete seepage barrier, excavated by a combination of clamshell and hydromill equipment. The main features of the three projects are summarized in Table 1. IntroductionTuttle Creek Dam was constructed by the U.S. Army Corp of Engineers (USACE) on the Big Blue River in North-East Kansas in the 1950s for flood control. Tuttle Creek Dam is a zoned earthfill embankment, 7,500 ft long and about 137 ft high with a crest width of 50 ft (Fig. 1). It is located in an area of moderate seismicity associated with an old continental rift zone located just to the east of the dam. The USACE, under the Dam Safety and Assurance Program, determined the need for remediation. Site investigations and geotechnical analyses identified the upper alluvial foundation sands as being susceptible to liquefaction when subjected to the Maximum Credible Earthquake.In 2005, USACE awarded a construction-manager-at-risk/early Contractor involvement contract. The USACE and the Contractor closely cooperated to identify the most effective technologies, materials and configurations to be used in the remediation. The original remediation design required both the upstream and downstream slope stabilization of liquefiable foundation. Results of refined seismic deformation analyses revealed that the stabilization of the downstream slope and toe was needed to protect the downstream seepage control system and to provide assurance that a liquefaction-induced flow slide would not occur (Stark et al., 2012)."

Jan 1, 2016

By Juan M. Pestana, Jeremy M. Gasser, Cuneyt Gokmen, Paul J. Sabatini, William Tanner, Daniel J. Woeste

An access pathway and working platform were designed and constructed for equipment access for a Deep Soil Mixing (DSM) pilot study over a coal combustion residual (CCR) surface impoundment (SI). The DSM pilot study was conducted to evaluate slurry mix designs and construction techniques for installing DSM columns up to 95 feet deep. Two-dimensional (2-D) limit equilibrium and 2-D finite element analyses were used to evaluate multiple failure mechanisms including: (i) bearing capacity, (ii) punching shear of mixed ground and underlying CCR, (iii) effect of fluidized DSM columns on working platform stability, and (iv) liquefaction. The analysis results were used to design ground improvement required to increase bearing capacity and stability of the CCR under the proposed equipment access route. A long-reach excavator was used to perform shallow bucket mixing and walk onto the CCR SI atop previously mixed cells following a minimum cure time and acceptance of quality control test results. Prior to mobilizing the DSM rig, a static load test was conducted to evaluate performance of the working platform. Both the access pathway and working platform demonstrated acceptable performance under the design loads during the DSM pilot study. This case study emphasizes the economic and safety benefits that can be realized by appropriately designing critical temporary work items such as access pathways and working platforms in difficult ground conditions. INTRODUCTION A Deep Soil Mixing (DSM) pilot study was conducted at a coal combustion residual (CCR) surface impoundment (SI) to evaluate slurry mix designs and construction techniques for closure design of the SI (Site). Sluicing of CCR at the facility ceased and closure will be initiated based on requirements in the final United States Environmental Protection Agency (USEPA) Rule for Disposal of Coal Combustion Residuals from Electric Utilities, 40 CFR 257, effective October 19, 2015. The proposed closure approach involves constructing a DSM containment structure (DSM Wall) to separate the SI into two areas: (i) a closure by removal area; and (ii) a consolidate and cap-in-place area. The proposed DSM Wall would retain the CCR within the consolidated closure footprint and provide a barrier between the two areas of the SI. The predominant CCR in the SI where the pilot study was conducted were fly ash and bottom ash. CCR materials in surface impoundments are generally soft and saturated as a result of being sluiced into place and can present stability and safety challenges when performing earthwork activities.

Jan 1, 2019

By Takefumi Takuma, Tsunenobu Nozaki, Masashi Nagano

Using sheet piles and pipe piles for permanent earth retaining is one of the most economical methods for constructing basement walls since they can also work as temporary shoring during construction. A major mixed-use redevelopment project in the UK, encompassing two to three large city blocks, utilized both sheet and pipe pile walls for a two-level subterranean parking structure. The 290m (950ft) x 100m (330ft) basement’s steel walls were designed to temporarily support excavation during construction and eventually to become a load carrying permanent structure in order to expedite the construction process and to achieve cost reduction. Two types of press-in piling machines, one for sheet piles and the other for pipe piles, were used for the job because of their abilities to press in sheet and pipe piles within tight tolerances for finished walls, for difficult installation conditions with very hard soil, and for its very low noise and practically zero-vibration operation; an essential factor for the job in close proximity to other businesses and residents. BACKGROUND Steel sheet pile and pipe piles have been used for many purposes including earth retaining. They are produced at steel mills and spirally welded at a fabrication yard to their corresponding specifications under strict quality control measures. Therefore, they can form highly reliable walls to its design capacity with proper installations. Their advantages as underground walls are:  They can form a high level of water cut-off function with their interlocks sealed by welding or with hydrophilic materials. See Figure 1 for a few examples for a sheet pile application.  They can carry vertical loading in addition to horizontal load and bending moment.  They can be a self-standing and temporary/permanent wall with flexible design and construction processes; bottom-up, top-down or hybrid sequences can be chosen per the project’s needs.  They can form a thinner wall than other wall types, creating larger inner space. See Figure 2.

Jan 1, 2019

By Nasr Sheta

"After Hurricane Sandy, the stability of an earth slope in the Atlantic Highlands, New Jersey in the United States was deteriorating due to slumping soils and erosion from flooding. A slope stability evaluation indicated the slope did not satisfy the requirements of the local building code. A triple-tier, pile-supported and mechanically stabilized earth wall was designed and constructed to stabilize the slope. The construction was planned from a 3-m-wide roadway and, because of rough terrain and limited work space at the site, a cast-in-place drilled-pile construction was deemed impractical due to slow pile production. An alternative procedure was utilized by pre-drilling holes, and installing precast tip-and-shaft-grouted (PCTSG) piles, which extended to competent soils to improve slope stability. A grade beam, connecting the PCTSG piles along with soldier beams and concrete lagging were used to form the lowest tier of the slope stabilization, while the middle and higher tiers were built as mechanically stabilized earth. The stability of the proposed stabilization was analyzed using 2-D non-linear finite elements. After construction, monitoring of the wall continued for about 8 months to check its performance, and indicated lateral and vertical wall movements were less than 25 mm and 6 mm, respectively, indicating effective slope stabilization.INTRODUCTIONStabilizing earth slopes using piles to connect near-surface unstable soils to underlying stable ground masses has been investigated by many researchers, who presented various approaches to evaluate the contribution of the pile system towards improving the stability of the slope. Some of these approaches consider the piles as structural elements receiving forces from the upper sliding ground mass and transmitting these forces to the underlying stable one. The force from the top sliding mass is applied at between one third and one half of the pile embedment into the top sliding mass, Anagnostopoulos et al. (1990), Fukuoka (1977) and Matsui et al. (1988). The point of application of the sliding force was explored based on successful case histories while addressing the safety factors for both geotechnical and structural design, Vessely A. et al. (2007). The development of numerical analysis techniques utilizing the method of finite elements (FE) also enabled better analysis and design of slopes stabilized using piles. A FE-based approach was successfully utilized to design slope stabilization with target safety factor based on the shear and bending demands and the spacing of the piles, Pradel D. et al. (2010).After Hurricane Sandy in October 2012, the stability of many properties constructed atop earth slopes located along the coast of the Atlantic Ocean has become a concern due to storm-induced erosion. This paper presents the analysis, design and construction of a hybrid slope stabilization system utilized at one of these storm-impacted properties, which is located in the Atlantic Highlands, New Jersey in the United States. The subject property consisted of a two-story residential dwelling and a parking structure, and was built on top of an about 8-m-high earth slope having crest at about elevation 10 m (el 10) and toe at about el 2."

Jan 1, 1900

By Fei-chiu Huang

A 17-acre landslide occurred in February 2001, on a slope below Via Bellota in the City of San Clemente, California. Three homes were destroyed and many others placed in jeopardy. The landslide, involving portions of five separate developments, continued to move significantly in the years following. Litigation ensued among the affected parties, and investigations continued through 2007. A mediated repair resolution was ultimately reached among the parties. The agreed upon repair consists of a multi-million dollar stabilization program that included grading, drainage, and structural systems. Part of the construction cost was offset by creating 4 new ocean view custom lots and 20 new mobile home lots. The landslide repair and slope stabilization design involved removal and replacement of portions of the landslide debris and construction of buttress and stabilization fills as well as installation of 74 shear pins in two rows. The shear pins were designed as 4-foot diameter by 50 feet in length and incorporated continuous W30x211 wide flange steel. The shear pins were designed to be installed 25 feet above the slide plane and 25 feet below the slide plane at each location. Construction of the 74 shear pins was initiated in 2008 and completed in 2009. Four-foot diameter holes were drilled by utilizing a truck-mounted, flight-auger-style drilling rig with a 4-foot diameter solid-flight auger. Prior to the installation of the shear pins, an engineering geologist downhole logged strategically selected holes to further evaluate the actual slide plane elevations. The wide flange steel shear pins were then lowered to the desired elevations and encased within 4,500 psi, Type V, 0.45 maximum water/cement ratio concrete. Inclinometers installed within four pin shafts and behind the pin rows indicated performance in accordance with the design. Slight to non-perceivable shear displacement was measured which mobilized the intended capacity at the monitored shear pins. No excessive slope movement was detected at any of the inclinometer locations during or after the construction period. Actual shear displacement of the steel wide flange elements was less than the movement anticipated before shear pin installation.

Jan 1, 2010

By James M. Tantalla, Dwight Metcalf, Roderic A. Ellman Jr.

"The construction of a new low head hydro-electric plant at the Cannelton Lock and Dam required the design and construction of a cofferdam to accommodate a deep excavation extending approximately 150 feet below the Ohio River levels. The new plant, which generates about 390 GWh of electricity annually, is owned by American Municipal Power (AMP). A specialist team was assembled to design and construct the cofferdam, marine dike and CB slurry wall that helped make the project successful and on time for project delivery.Because the new plant diverts water from the locks and dam through a powerhouse to generate power, it would need to be partially in the river to operate properly. To accomplish this, approximately 250,000 square feet of land was reclaimed from the river by construction of a marine dike. The dike, combined with the design and construction of a 150 foot deep cement bentonite (CB) cutoff wall enabled construction of the new plant in the dry. Extensive dewatering analyses were performed using Modflow to evaluate pumping requirements and the number of wells needed to maintain ground water at required levels within the side slopes and final subgrade. A monitoring program consisting of inclinometers, piezometers and movement monitoring points were used to monitor cofferdam stability and performance throughout construction. Detailed two and three dimensional stability analyses that included a parametric study of fluctuating river levels and slurry unit weight were performed to ensure stability and suitable low permeability of the trench during cut-off wall excavation both on land and in the marine dike. The wall was constructed with both a hydromill excavating primary panels and a clamshell following behind to construct secondary panels. Data acquisition systems onboard the excavating equipment allowed for detailed confirmation of the continuity of the wall at each interface between panels. Another challenging aspect was the CB mix design for the trench. The cofferdam required the construction of a 1,300-foot long marine dike downstream of the existing dam up to 100 feet tall founded on existing river sediment to enclose the site and cut-off the seepage into the excavation from the river. Marine dike construction utilized vibro-compaction to pre-densify granular fills placed underwater through which the CB trench extended."

Jan 1, 2016

By Robert Bachus, Nikolaos Machairasm, Allen Cadden

Data Interchange for Geotechnical and Geoenvironmental Specialists (DIGGS) is a data transfer standard that is gaining widespread acceptance in the geotechnical and geoenvironmental communities. Originally developed using funding from the Federal Highway Administration (FHWA) to efficiently capture data related to geotechnical boring logs, cone penetration test (CPT) soundings, and lab testing results, the data transfer protocol is rapidly gaining traction. It has been shown to have beneficial impacts in other allied areas where disparate parties (i.e., consultants, contractors, vendors, etc.) routinely publish/submit data as part of project deliverables. The historic problem is that many of these submissions use paper copies (i.e., .pdf images) to transmit valuable data for the project… data that may extend beyond the “technical” aspects of the project (e.g., equipment operating conditions, construction production rates, project costs, etc.). These data could be used by multiple parties to assess project performance and safety, as well as to track productivity, etc. Currently, in the limited situations when actual data are compiled and transmitted, the data often are submitted as an author-specific (and often proprietary) software application and must then be re-entered into other software applications (e.g., analysis software, database, etc.) for use beyond simple data collection. An initiative undertaken by the Geo-Institute (G-I) of the American Society of Civil Engineers (ASCE) focuses on exploiting the full potential of DIGGS to geoprofessionals both within and outside of the transportation community. The deep foundations industry represents one community that could benefit significantly from using DIGGS. Data of interest to DFI members include production records, quality assurance information (e.g., verticality and alignment, concrete strength), and, importantly, load test results. When adopting DIGGS, users need not modify how they capture data, but rather will use DIGGS as a vehicle to transfer data to other applications in a standard format where it can be shared, used, stored, and retrieved. This paper and associated presentation will describe DIGGS and demonstrate how DIGGS can be used effectively within the deep foundations community.

Jan 1, 2019

By N. Schmitz

This paper explains how new digital solutions improve reverse circulation drilling operations. Upgrading field-proven reverse circulation drilling (RCD) rigs with new digital technologies enables semiautomated drilling, with upgrade options for fully automated & remote drilling. Key elements of the improvements are electrically controlled valve systems, process instrumentations, a state of the art machine controller and drilling operation via a touch control panel. Automation of core processes, such as adding drill pipes, reduces set-up times, increases machine uptime for drilling and as a result efficiency. While drilling, sensors provide continuous feedback, which is used to automatically adjust e.g. the weight on bit to the optimum; resulting in an increased rate of penetration and less wear and tear. While in the past hydraulic power packs (HPU) have typically been operated at a constant high-performance level with related high fuel consumption, a new interface between the machine controller and the power unit regulates the HPU performance exactly according to the actual drilling operation needs. This leads to significant fuel consumption reduction. The safety benefits of the digital improvements are the ability to remotely operate the rig in challenging site conditions via a mobile operator panel.

Sep 8, 2021

By Massimo Poggio, Gabriele Balconi, Andrea M. R. Pettinaroli, Mario Ruggiero, Riccardo Castellanza

Grouting technologies are ground treatment techniques used for modifying the behaviour of a mass of soil or rock by injecting a mixture. The sleeved port pipes (also called Tube A Manchette) are highly diffused for grouting treatment of coarse soils and fissured rocks. This paper describes a combination of jet grouting and rock grouting with MPSP (multiple packer sleeve pipe) technique that has been used to realize waterproof curtains under fluvial structures for a cascade hydro-power plant. This is composed by five mini hydro-power plants, placed along the Iskar River, in Bulgaria, and composed by a penstock followed by the power house, a spillway, and an earth dam containing the reservoir. The geology of the site is characterized by an upper alluvial deposit lying over the bedrock. In each site, similar treatments were carried out: an impervious curtain along the plant section, obtained by executing jet-grouting columns in the surficial alluvial layers and grouting the underlying fractured rock by means of port pipes. The temporary embankment, built during the works for protecting each site from the possible river floods, has been waterproofed and stabilized by reinforced jet-grouting columns. The grouting processes have been controlled and monitored by a computerized system. INTRODUCTION The Iskar river cascade hydropower plant is situated northern of Sofia, Bulgaria, and it is composed by nine plants. Actually five of them have been built and produce energy. Each plant is composed by a penstock followed by the turbine building, a spillway, and an earth dam that contains the reservoir. The Iskar rivers runs in a narrow valley characterized by diorite or diabase rocks, with an upper deposit of alluvial soil, composed mainly by gravel and sand. Each plant requires an impervious curtain under the structures and in correspondence of the earth dam: this has been obtained by means of a jet grouting treatment of the alluvial coarse soil, and a grouting treatment with cement mixtures of the underlying rock using the MPSP technology. During the construction of the structures, the site has been shielded from the river water by a temporary earth embankment that has been statically improved and waterproofed by jet grouting columns reinforced with steel tubes; this allowed to work without interruption even in case of flood of the Iskar river.

Jan 1, 2019

By Sumantra Sengupta

"Northeast Frontier Railway (NF Railway) intends to connect Imphal, the capital of Manipur (bordering Myanmar) with Assam by railway link. They have planned a 125km long railway line that passes through steep rolling hills of Patkai region, eastern trail of Himalaya, and as a result large number of tunnels and bridges need to be designed. While the high mountains are penetrated by tunnel, the deep gorges between the mountain ridges are connected by tall bridges. The tallest of such bridges connects a gorge at about 140m above its bed level with an overall length about 700m at rail level. In all, five such bridges with tall piers are now under construction. With extensive study on possible alternate arrangement of the bridges considering the effect of high seismicity of the area, moderately to highly weathered siltstone/ sandstone as ground bed material, slope of the hills etc it was decided that bridge will be founded on 1.5m diameter bored cast in situ piles with length varying from 20m to 30m depending on the location. The substructures are RCC hollow pier and superstructures are steel open web through type girder of 103.5m span. Considering absence of any major construction work in the vicinity, it was decided that prior to design work, Site-specific spectrum study will be carried out and design will be carried out considering the varying stiffness of the tall piers, each of different height. Interesting results were obtained regarding behavior of piles under lateral loads generated by high seismic conditions. The paper discusses in detail the design of Pile foundations and the effect of bed material along the steep slope on which the piles are being constructed.INTRODUCTIONIndian Railway has undertaken the construction work of connecting the North-Eastern states of India through railway line. The major stretches of the area passes through hilly terrain and as a result the line passes through tunnels and bridges in succession. The tall mountains are being penetrated with tunnels and immediate after deep gorges are crossed with high level bridges. The entire area is under high seismically active zone. The bed material below the ground level of the sloped hill is 4 to 10 meter of mixed soil of sand, gravel, pebbles etc underlain by moderately to highly weathered sandstone, siltstone at the higher level and moderately weathered sandstone, siltstone at lower level. Considering all the aspects like constructability, maintainability, geological and geotechnical aspect, seismicity, stability, safety, functional aspect and cost it was finally decided that the bridges will be simply supported structure with open web through type steel superstructure of maximum span 103.5m and hollow cylindrical discretely varying RCC substructure with 1.5m diameter group of piles as foundation. The paper discusses on the design aspect of the pile foundation in the rocky strata in the hill slope. The codes and standards that have been followed for design are IRS (Indian Railway Standard), IS (Indian Standard), IRC (Indian Road Congress), AREMA (American Railway Engineering and Maintenance-of-way Association), UIC (International Union of Railway) provisions."

Jan 1, 2015

By Jamey B. Rosen

As Project Information Management Systems (PIMS) technologies develop, the range of projects to which one can apply these technologies grows while the cost to apply them shrinks. In recent years, technologies previously limited to large “megaprojects” (e.g., major dam rehabilitations) owned by major entities (e.g., the United States Army Corps of Engineers) with large budgets have been applied to smaller projects with less stringent specifications and more modest budgets. This paper will describe applications of PIMS technologies to small projects with limited budgets, including examples from levee construction, small-scale grout curtain installation, and diaphragm and secant pile cut-off walls. We will include a demonstration of how PIMS technologies can effectively analyze verticality data from koden and hydromill data streams to automatically generate models and as-built drawings showing overlap and deviation along the depth of the foundation. INTRODUCTION This paper discusses the application of Project Information Management Systems (PIMS) technologies to geo-foundations projects, with a focus on technologies and examples that are in a lower cost range. PIMS technologies allow contractors and other stakeholders to perform efficient quality control on their data, generate quick or automatic reports and as-built drawings, perform analyses to better understand their construction, and ultimately use their data to increase the quality of their construction. As PIMS technologies are relatively new to the deep foundations industry, and owner specifications on their use are generally viewed as complex and limited to large scale projects, PIMS technologies are frequently viewed as an expensive component that is beyond the scope of a smaller or simpler project. However, the same principles and techniques generally associated with large projects can be applied to projects at smaller scale. Furthermore, as these technologies develop both in the deep foundations and other industries, the cost of application is decreasing quickly making them even more affordable for smaller projects. The remainder of this paper provides some justification for applying PIMS technologies, describes some scalable data management concepts and workflows and then provides some examples of “low cost” applications of these technologies.

Jan 1, 2019