Search Documents

By Stuart Coutts

"This paper presents an overview of the author’s experience related to the assessment of the base capacity of straight shafted and enlarged-base bored piles in sand. A design approach based on CPT qc is described which has been calibrated using a database of load tests. The importance of correct installation techniques with instrumentation are illustrated and a discussion is presented on the current use of high strain dynamic testing to validate compliance with design. An example of a recent project with high quality instrumented load test data illustrates the close match to the proposed best practice approach and also highlights the importance for consideration of the effects of stress relief for deep foundations installed in deep excavations.1 INTRODUCTIONContinuous Flight Auger (CFA) piles are the bored foundation pile of choice for sand deposits across Australia. The evolution of the determination of the base resistance of CFA piles has been shaped by available investigative techniques, calculation methods, and calibration of designs with laboratory and field testing. The Cone Penetration Test (CPT) has been widely used in Western Australia (WA) where the test has been commercially available via multiple contractors for more than 25 years. On the East coast, the adoption of CPT testing has been slower with a transition from traditional Standard Penetration Testing (SPT) still occurring. Dynamic pile load tests are often used to derive parameters. The influence of pile installation on performance is commonly misunderstood and is an important element on any discussion of pile capacity for CFA pile types. The interface between the base of the constructed pile and the in-situ soil has an influence on capacity such that a poorly constructed pile base will have limited (if any) contribution to pile performance within the normal working range, generally within a 10 mm movement. The research presented in this paper pertains to CFA piles (no drilling fluids) and enlarged base piles constructed using CFA techniques under drilling fluids such that clean pile/base interface is targeted. Developments in modern piling equipment and instrumentation allow the pressure and volume of delivered concrete/grout to piles to be accurately monitored at various stages of installation such that repeatable ‘best practice’ can be achieved. The changes in soil conditions that occur due to the disturbance of the install technique are also important.Although the results of this research are likely applicable to bored piles, the interface between the pile and in-situ soil (shaft and base) need to be considered for various installation techniques. The effects of stress relaxation (due to removal of soil above pile base and adjacent shaft), time to concreting, and the zone of disturbed soil around the pile shaft are paramount.2 INSTALLATION CONSIDERATIONS The pile mix (concrete/grout) and interface with the in-situ soil are also an important consideration. For example, coarse grained, poorly graded, dry, clean sand will be partially permeated by most pile mixes; such that the influenced soil will be enhanced and in instances the overall effective pile dimensions increased. Permeation of the disturbed zone of a pile or anchor shaft along with scale effects (Lehane 2009) can have significant effect on shaft capacity and shaft frictions significantly exceeding expected are not uncommon based on ‘theoretical’ dimensions. Advancements in mix technology and mix techniques also have a large influence on the pile/soil interface. The ability of the piling rig and augers to excavate a plumb and gauge hole can also have a large influence on the zone of soil disturbed adjacent the constructed pile with a resulting influence on capacity."

Jan 1, 1900

By Babak Mamaqani, Pirooz Barar

Regional Connector Transit Corridor (RCC) is part of the Los Angeles metro expansion project under construction which adds three new stations into the system. PB&A was responsible for the design of the support of excavation (SOE) systems for two stations, 2nd/Broadway and 2nd/Hope, in RCC. In this paper, challenges and lesson learned from SOE design of 2nd/Broadway station with a main focus on underpinning design are discussed. 2nd/Broadway station required to cut and cover excavation of 500 ft long by almost 100 ft deep, underneath 2nd Street. SOE systems consisting of drilled soldier beams with tiebacks and/or struts. The main challenge in 2nd/Broadway station was to underpin the LA Times building which was partially protruded into the station. A chellenging underpinning system consisted of concrete panels and ground anchors was designed to support the building surcharge and prevent settlement. The underpinning system was designed based on METRO design criteria and the deflection was evaluated by Finite Element Analysis (FEA) program, PLAXIS 2D. A maximum deflection of 0.4 inches was calculated to occur at the top of the underpinning system. Data from settlement and tilt sensors showed minimal movements which aligned with PLAXIS outputs. PROJECT DESCRIPTION The Regional Connector Transit Corridor (RCC) is Los Angeles Metro’s ambitious Light Rail Project. It runs under the City’s main thoroughfares, Flower and 2nd Streets, and when complete will alleviate traffic and parking congestion in downtown Los Angeles. The Regional Connector will connect thousands of residents living in the bedroom communities of the Inland Empire and Long Beach to their jobs Downtown. The rail line will serve 1.9 miles, using the $1.756 Billion budget to construct the underground rail line, including 3 new stations, at 2nd & Hope Street, 2nd & Broadway, and 1st St. & Central Ave (Fig. 1).

Jan 1, 2019

By David Guy, John Stanbury, Gilbert Tallard

"In 2009, storm surge from Hurricane Sandy inundated the Bay Park Sewage Treatment Plant located at El. +4 to +12 (+1.2 to +3.6 m) in East Rockaway, Long Island, NY. With all systems down, raw sewage water mixed in the floodwaters. A recurrence of such an event being unacceptable, and in view of rising future sea levels, a flood protection project was developed by Nassau County with funding coming in large part from the federally funded Sandy Rescue Fund. Designed by Arcadis/Hazen & Sawyer Engineers J.V., the protection took the form of a perimeter barrier capable of withstanding future storm surge. Due to limitations imposed by property lines and existing facilities, a levee design with three different types of cross section was developed to adapt to each location, adding construction complexity. The Long Island subsurface is characterized by beach sand extending to great depth. The clay required for the core and levee cover therefore had to be brought in from out of state. A thin silty clay layer at El. -23 to -25 (-7.0 to -7.6 m) served as an aquitard. The under-seepage was reduced by a hanging cut-off wall designed as a vibrated beam thin wall and filled with a salt water resistant, low permeability, self-hardening slurry.INTRODUCTIONOn October 29, 2009, Hurricane Sandy hit New York City, with a devastating effect on the region. The low lying Bay Park Sewage Treatment Plant (STP) (Fig. 1) serving Nassau County on Long Island was submerged (Fig. 2). All basements and underground mechanical facilities were flooded (Fig. 3) and millions gallons of effluent were released into the waters of the nearby Hewlett Bay which connects via other small waterways to the Atlantic Ocean."

Jan 1, 2016

By Abid Adekunte

"In recent years, developers have had to deal with complexities associated with numerous cases of deep basement construction in built-up areas. Design and construction of deep excavation support systems in urbanised zones come with many technical challenges. Restricted working spaces often render the use of temporary struts as wall restraint systems unpopular, as working space needs to be maximised. Also, tie-back anchors are often inapplicable due to the existence of adjacent structures. Therefore, developing alternative restraint systems for deep basement structures in builtup areas is becoming increasingly important to the present day basement engineer.This paper is centred on the design, construction and monitoring of enabling works for deep basement structures on three sites in the United Kingdom and Republic of Ireland. Traditional tieback anchorage and propping systems were inapplicable on the sites. As alternatives, separate novel wall restraint systems were developed and adopted, to enable excavation on each of the three sites.Performances of the novel wall restraint systems, as well as the responses of adjacent structures were monitored. Numerical modelling and field monitoring results show the three alternative wall restraint systems to be safe and effective. The paper also highlights the advantages of the novel solutions over conventional methods.INTRODUCTIONRecently, deep basement structures have become popular components of urban building developments. As pointed out by Pearlman et al., 2004, this could be attributed to the inadequacy of surface parking spaces in urbanised zones, while underground parking facilities are also believed to improve both aesthetic and commercial qualities of urban structures.However, while the incorporation of basement structure into new urban development appeals to developers and architects, the engineering design and construction aspects of basement works typically come against a whole lot of complexities and challenges. As highlighted by Wong, 2002, engineering problems associated with basement construction in built-up areas are numerous, some of these include; complicated sub-soil conditions, dealing with excessive active pressures, complex temporary works, proximity of sensitive adjacent structures, high level hazards to construction workmen and surrounding community, inadequate working space, etc."

Jan 1, 2015

By Meeok Kim, Paul Beljan, Gordon Chen

"Clinton combined sewer overflow storage (CSO) facility project developed by the Department of Water Environment Protection of Onondaga County, New York, is to improve sewer facilities and infrastructure in Syracuse, New York. The below grade facility will provide a storage of untreated stormwater during highflow periods to be treated later, thus reducing CSO discharges to Onondaga Creek.The CSO system consists of three parallel storage tunnels and two end chambers (west and east chambers) as main underground structure. The storage tunnels are about 850 ft. long, 55 ft. wide, 24 ft tall and located 20 ft deep below grade. The chambers, include above access and operation structure, are about 40 to 55 ft. deep and approximately 60 to 100 ft. wide.Kiewit Infrastructure and Weidlinger Associates Inc. developed an alternative approach for the tunnels to meet the facility completion schedule, strict design guide lines and quality control as an environmental and water tight concrete structure for the project. The original design anticipated use of a TBM machine to bore three parallel tunnels between two previously constructed chambers.The alternative design used a three barrel culvert cast-in-place structure in a cut and cover excavation supported by a soil bentonite wall. The SOE along the jet grouted bottom seal provided a ground water cut off as well.The SOE system is specially designed to enhance the quality of culvert CIP structure construction by providing enough space for a full height construction. Also it further reduces the construction time by having the less squarefootage of jet grout installation. The design of tunnel systems is accomplished effectively through the utilization of soil structure interaction using a finite element methodIntroductionTo avoid construction of an additional treatment plant to handle increases in combined sewage flows, the Department of Water Environment Protection of Onondaga opted to construct the Clinton combined sewer overflow storage (CSO) facility.The Clinton CSO facility provides an environmental friendly mitigation method for combined sewer overflows on Onondaga lake which is located in northwest of Syracuse."

Jan 1, 2015

By Timothy C. Siegel, Derrick Dasenbrock, Rich Lamb, Paul J. Axtell

"The axial resistance provided by deep foundations may be divided into two components: side resistance and tip resistance. The direction that the side resistance acts depends on the relative movement between the deep foundation and the adjacent soil. That is, when the foundation moves downward relative to the soil, then the side resistance is positive and acts upward. Conversely, when the soil moves downward relative to the foundation the side resistance is negative and acts downward. Research supports that both positive side resistance and negative skin friction develop in essentially all deep foundations. The side resistance distribution is a function of the soil strength and stiffness, the applied top loads, and whether the top load is sustained, transient, or a combination of sustained and transient loads. Consideration of drag load and downdrag has become more convoluted with implementation of geotechnical aspects into the AASHTO LRFD Bridge Design Specifications and its use of load and resistance factors. This paper examines the current AASHTO Specifications and presents an alternative design approach for drag load and downdrag using the LRFD framework. The alternative design approach is illustrated by two examples involving drag load and downdrag.IntroductionThe axial resistance provided by deep foundations may be divided into two components: side resistance and tip resistance. The direction that the side resistance acts depends on the relative movement between the deep foundation and the adjacent soil. That is, when the foundation moves downward relative to the soil, then the side resistance is positive and acts upward. Conversely, when the soil moves downward relative to the foundation the side resistance is negative and acts downward. Research supports that both positive side resistance and negative skin friction develop in essentially all deep foundations. The side resistance distribution is a function of the soil strength and stiffness, the applied top load, and whether the top load is sustained, transient, or a combination of sustained and transient.Consideration of drag load and downdrag has become more convoluted with implementation of geotechnical aspects into the LRFD Bridge Design Specifications and its use of load and resistance factors. This paper examines current LRFD design specifications and presents an alternative design approach for drag load and alternative design approach is applied to several examples where drag load and/or downdrag may control design."

Jan 1, 2015

By Abid O. Adekunte, David Greentree, David Hilton

"The construction industry is witnessing an upsurge in demand by property developers to have basements incorporated into their residential and commercial development schemes. This is attributable to perceived improvement to aesthetic and commercial values of buildings by underground space, amongst property owners. This trend is compelling more owners of buildings with no basements to explore the possibility of creating underground additional space beneath their existing buildings. The creation of a basement beneath an existing building entails the installation of a reinforced concrete (RC) underpinning system, temporary works, bulk excavation to basement formation level and construction of the basement structure, with associated aesthetic finishes.The L-shaped segmental RC underpins are a common system of choice for such underpinning works. They are multi-functional; providing vertical support to the existing superstructure, providing lateral support to earth and groundwater, supporting temporary and permanent surcharge loads from adjacent structures and services, whilst also forming part of the basement slab. This paper focuses on the first function of the Lshaped RC underpins; capacity under vertical compressive loading from the superstructure. The most common industry approach for the prediction of vertical capacities of L-shaped underpins is the oldfashioned Meyerhof’s (1953, 1963) effective width method, which is based on the traditional bearing capacity theory, whilst accounting for correction factors for eccentricity and foundation depth.The traditional bearing capacity formula is surrounded by a significant degree of uncertainty; estimates are highly user-dependent, as capacity prediction is sensitive to the chosen angle of shearing resistance (?), while there are difficulties in accurately measuring the in-situ ??value of cohesionless soils. In addition, the effective width approach has been shown to be very conservative by many research workers. The segmental RC underpins presented in this paper have been designed with an alternative less conservative method, which involves the use of a recently proposed consistent work-hardening plasticity model calibrated with field-based tests on footings of various aspect ratios and relative embedment in sand. The paper highlights the principles behind underpinning works for urban basement construction, the design of L-shaped RC underpins with the recently proposed plasticity model and the advantages of the method over traditional bearing capacity solutions and pre-existing plasticity models."

Jan 1, 2016

By Yazen Khasawneh, Osvaldo P. M. Vitali, Mohammad Nassim

The demand for renewable energy is growing as the conventional energy resources are becoming more limited and we are more conscious about the negative impact of conventional energy sources on the environment. Wind turbines technology is evolving in a fast pace, the towers are becoming taller, and the rotors are getting larger. The challenge is to maintain the Levelized Cost of Electricity (LCOE) as low as possible to ensure a sustainable and an economically feasible energy supply. Thus, the foundation systems for wind turbines should evolve to meet the increasing load demand, while reducing the LCOE. In this paper, an innovative foundation system for onshore wind turbines is presented. The new foundation system is the conventional P&H tensionless pier foundation (PHTP) with a reinforced concrete collar at the top of the pier. 3D FEM modeling was conducted to assess the benefits achieved by adding a collar at the top of the PHTP foundation. The numerical results show a significant performance enhancement of the proposed foundation system over the conventional PHTP foundation. The enhanced foundation system also has an economical advantage because the depth of the pier can be greatly reduced while maintaining a superior performance.

Sep 8, 2021

By Stefan Swartling, Rudy Lyon, Donald A. Bruce

"Since their first production application in Sweden in 1995, water-powered, down-thehole hammers (WDTH) have been used throughout the world in many different drilling applications, total lines, over 25 million lineal meters of drill hole. This paper reviews the history and principles of down-the-hole drilling (DTH) in general with both air and water, before focusing on the details of WDTH hammers. A summary of the numerous and considerable advantages of WDTH drilling is provided, with particular emphasis on their superior productivity, smaller deviation, applicability in sensitive/urban conditions, environmental protection and much reduced energy requirements.HISTORICAL PERSPECTIVE ON PRODUCTION DRILLING METHODSAir-flushed drilling with top hammers began in the mining industry in Sweden in 1873, while down-the-hole (DTH) drills, again with air flush (and activation) became operational in 1950. During that same time interval, Simon Ingersoll had patented the first steam-powered, top hammer rock drill to provide higher productivity in blast hole drilling. It is well known that water, as an activating, flushing and cooling medium, has many significant advantages over the use of air. However, it was not until 1973 that top hammer systems (either air or hydraulically activated) for larger rigs were adapted to the use of water flush, typically via “under the head” swivels.The concept of a water-powered, down-the-hammer (WDTH) had been explored prior to G. Drill acquiring the original patent from Atlas Copco in 1988. LKAB, a huge underground mining company owned by the Swedish Government and providing about 90% of the European Union’s iron ore, purchased G. Drill in 1991 and encouraged the commercial development of the WDTH. The first full-scale WDTH production works were carried out for LKAB in 1995, since when over 25 million lineal meters of drilling have been recorded in both underground and surface applications.In 2001, G-Drill was renamed Wassara, which today still holds the worldwide patents for WDTH technology. Regarding North American usage, the first significant application was by Advanced Construction Techniques (ACT) Ltd. during the test grouting program conducted for the U.S. Army Corps of Engineers at McCook Reservoir, Chicago, in 2002. Since then, WDTH has become the tool of choice for specialty drilling and grouting contractors on dams and other major structures throughout the U.S."

Jan 1, 2015

By Abhijit Saha

"The stone columns improve the performance of foundations on soft and loose soil due to the ability of composite ground to sustain increased structural loads under reduced settlements. The interaction between the two basic elements: the ambient subsoil and installed column, present a complexity of behaviour, both in terms of applied stresses and resulting strains. Moreover, as the same is provided in-group in a regular array beneath foundations, the performance of an individual column is likely to be influenced by the presence of neighbouring columns. The present paper addresses this very issue. Analysis of reported field hydro-test data of large diameter oil storage tanks in soft ground in reference to some existing theories led to the development of the stone-column ‘group efficiency factor’. In order that such factor is of general use, it was felt necessary to examine the applicability of the factor to different sizes of groups under varied subsoil conditions. With this in view, some model test results reported in literature of single and group of columns have been analysed and in the process an explicit relationship regarding the stone-column ‘groupeffect’ could be established.INTRODUCTIONThe field application of the stone column technology has gained momentum than the intricate design methodology due to its simplicity in installation and intuitive performance. The ground improvement is due to the complex interaction within the ‘unit-cell’ comprised of the installed column in ambient ground under sustained vertical stress; in association with the interdependence of problem geometry and material properties of the two different soils-one 'native' and the other 'back-filled'. The beneficial effects are increased load capacity, reduction in total and differential settlements, minimization of post construction settlements effected by accelerating consolidation, reduced risk of soil liquefaction, aiding in improvement of slope stability of embankments and natural slopes and effecting changes in the dynamic response. The ‘unit-cell’ concept of a tributary soil cylinder encapsulating an installed column with some reasonable assumptions and boundary conditions (Aboshi et al, 1979; Balaam & Booker, 1981; Van Impe & De Beer, 1983; Priebe, 1976; Saha & De, 1994; Saha; 2005, 2006, 2007, 2011, Saha & Das; 2007) deals with the load-settlement behaviour of the composite system. The present investigation is based on published field data from literature & validated with experimental study reported in literature. The study addresses the effect of group interaction of stone columns beneath a large area loading on ground settlement. The hydrotest load-settlement data of 12 large diameter oil storage tanks founded on stone column reinforced soil at Haldia1 and Kandla2 refinery sites in India; reported by Som (1997), has been analysed to quantify the group efficiency. The results as obtained are compared with experimental study on 2, 3 and 4 stone column groups at different spacing-diameter ratios in soft clay3 reported by Rao et al (1997) to validate the above analysis. A unique relationship between the column spacing and group efficiency has been obtained."

Jan 1, 2015

By Kamil Nuzha, Jianchao Li, Bashar S. Qubain

"The Philadelphia Water Department is rehabilitating Belmont Raw Water Basin. As part of this work, a 500-ft long, temporary cofferdam was designed to retain 35 ft of combined water and soil at the western half during the reconstruction of the eastern half. A cofferdam that comprises two integral rows of sheet piles was selected to take advantage of the soil’s weight between the sheet piles for increased stability. To fine tune the design, a geotechnical investigation was carried out to verify the subsurface conditions and, in particular, the top of rock variations along the centerline of the cofferdam. A detailed finite element analysis was performed based on the subsurface findings and incorporating the construction sequence to evaluate the behavior of the cofferdam at the following stages: installation of tie rods to connect to the two rows of sheet piles; partial excavation and installation of tiebacks; complete excavation of the east basin, and demolition of the cofferdam. Inclinometers and survey markers were installed every 100 ft along the cofferdam and were monitored throughout construction. The deformation measurements were in good agreement with the finite element results.INTRODUCTIONThe Philadelphia Water Department (PWD) Belmont Raw Water Basin is located at the intersection of City Line and Belmont Avenues in Philadelphia, PA. The facility actually contains two raw water basins, east and west, separated by an earthen dividing dike. Water leakage at the bottom of the basins and through the dividing dike together with increasing demand for a larger storage capacity dictated the replacement of the wide earthen dike with new narrower concrete structure. The temporary cofferdam was designed for a two-year period to facilitate excavation support, water cutoff, removal of the existing earthen dike and replacing it with a new concrete dike. During this construction sequence, the water level in the west basin had to be maintained at or near its full capacity.Various excavation support systems were considered for this project prior to the selection of a double wall sheet pile cofferdam. Fig. 1 shows a plan view of the cofferdam and the new dividing dike. A typical cross section of the two structures is shown in Fig. 2. Double row sheet pile walls are commonly used as both temporary and permanent retaining systems in open water applications such as construction works, quaywalls, breakwaters and revetments for storing industrial waste as indicated by Ohori, et al. (1984), Ohori et al. (1988), and Khan, et al. (2001). There are many advantages to double row sheet pile systems as recognized by Ohori, et al. (1984; 1988): (1) It can be installed and removed in the presence of water easily and quickly; (2) it provides stability with small width to height ratio, utilizing the existing soils between the installed sheet pile rows; and (3) it serves well as a means for water cutoff. These advantages meet the specific project requirements."

Jan 1, 2016

By Michael Oakland

This paper will discuss the design analysis of sheet pile cofferdams for static and dynamic blast loads. Following construction of the new Willis Avenue Bridge across the East River between Brooklyn and Manhattan, in-river piers No. 9 and No. 10 from the former bridge were demolished, partially by explosive charges. The blast at Pier 10 was conducted first and though the demolition charge was relatively small, it gave confidence that the sheeting could be designed to resist the blast load. This paper primarily summarizes our analysis and performance of a sheet pile cofferdam at Pier 9 used to withstand the larger blast loads, contain the blast debris, and allow excavation of the pier below the existing river bed mudline. The program NLFlex was used to predict stresses and deformations of the cofferdams under dynamic blast loads, using simplified equations to estimate the underwater blast pressures. Specifically, the analysis focused on the stresses in the struts, waler beam, sheet pile interlocks and connection of the sheeting to the waler beam. Design included allowing plastic deformations and limited rupture of the sheet pile interlocks under the blast loading. Comparisons are made between stresses assessed by the dynamic finite element modeling and empirical relationships used within the industry. The performance of the system after the actual blast is discussed as well as details of the performance of welded vs. bolted connections within the system.

By Jamey Rosen, Georgette Hlepas

Verticality data collected from panel and pile elements of seepage barrier walls describe the shape and position of those elements in three dimensions. These data are used to determine if a barrier wall is constructed as designed and if it meets the owner specifications with respect to tolerance (i.e., if each element is sufficiently close to vertical) and overlap (i.e., do adjacent elements overlap sufficiently to prevent leakage). Contractors use verticality data to confirm that their work matches the design, and owners use verticality data to verify the contractor’s work and confirm that specified criteria were met. Project Information Management Systems (PIMS) technology has been applied to the management, visualization, and analysis of verticality data. This paper will provide examples of how contractors and owners have used a PIMS to compile and synthesize data collected during excavations (e.g., from Cutter Soil Mixer and Hydromill drill rig telemetry), and from measurements of completed excavations (e.g., using the Koden ultrasonic tool), and used those data to model excavation geometry. We will present case studies of using these models to estimate backfill placement volumes, and to evaluate the verticality tolerance and overlap between elements.

Sep 8, 2021

By Mohammed Faizal, Abdelmalek Bouazza

"The operation of ground source heat pumps combined with foundation piles can have an effect on the thermal behaviour of the pile and the surrounding soil. This paper presents the effects of continuous heating, continuous cooling, and alternate heating and cooling operations on ground and pile temperatures as well as the thermo-mechanical behaviour of a field scale energy pile. The effect of pile operation on the ground temperatures is highest near the pile and reduces with increasing radial distance. The results of the present studies generally showed that the thermal elasticity of the pile is not affected.INTRODUCTIONGeothermal energy piles are foundation piles used as underground heat exchangers to maintain thermal comfort in buildings, via the use of ground source heat pumps (GSHPs). Ground source heat pumps are more economical and environmental friendly compared to conventional heat pumps. Energy piles can be combined with supplemental surface heaters or coolers, known as hybrid systems, for forcefully recharging the ground during non-operational times of the GSHP. Alternative heating and cooling of the GSHP improves geothermal energy usage and alleviates heat build-up in the ground and provides a balance of ground temperatures around the heat exchanger (Jalaluddin and Miyara, 2012).The temperatures induced in the piles during GSHP operation can lead to a complex response of thermal strains and stresses in the pile concrete. An assessment of the thermo-mechanical response of energy piles for various thermal loads may assist engineers in the design process. Furthermore, an assessment of ground temperatures will also highlight any potential thermal interactions with other energy piles in actual building operations.At present, the thermal strain and stress distribution in field scale energy piles has mostly been studied for continuous operation (Laloui et al., 2006; Bourne-Webb et al., 2009; McCartney and Murphy, 2012; Akrouch et al., 2014; Mimouni, 2014; Murphy and McCartney, 2014; Murphy et al., 2014; Wang et al., 2015). These studies have contributed considerably to the understanding of the axial thermal strain and stress distributions in the piles and have shown that pile thermal behaviour is mostly thermo-elastic without inducing major structural concerns.The present paper adds to the current knowledge by assessing the pile thermo-mechanical and ground thermal response for continuous and alternating thermal loads of a field scale energy pile. The operation modes studied are 24 hours continuous cooling (Faizal et al., 2015), 24 hours continuous heating, (Wang et al., 2015) and alternate heating and cooling operation (Faizal and Bouazza, 2016). The forced ground thermal recharging is done during the non-operating times of the cooling unit, simulating a solar hybrid GSHP system for a scheduled intermittent mode of operation."

Jan 1, 1900

By John P. Turner, Benjamin J. Turner

"Non-destructive testing and evaluation (NDT/NDE) methods have become standard tools as part of the post-construction quality assurance of drilled shaft foundations. In responding to anomalies, foundation designers, owners, and contractors face a number of choices, including: (i) acceptance of a shaft with known anomalies, (ii) further investigations of integrity (e.g., concrete coring), (iii) repair schemes, and (iv) reject and replace. To assist in selecting the best option, analyses are often performed that involve assessing the structural performance of reinforced concrete shafts that may include defective concrete or voids. Currently, the analytical tools for predicting the flexural strength and stiffness of drilled shafts with defective concrete located in discrete regions of the cross section are limited. This paper presents a robust moment-curvature analysis tool for drilled shafts based on the fiber-element discretization method. The tool allows for consideration of anomalous or defective concrete regions in the shape and location that they are believed to exist in the shaft while considering explicitly the nonlinear material behavior of the intact regions based on expected material properties. A case study is used to illustrate the practical application of the analysis to drilled shaft projects.INTRODUCTIONImperfections such as defective concrete or accidental eccentricity of reinforcing cages are an inherent part of the drilled shaft construction process that will occur occasionally even when construction best-practices are followed. Petek et al. (2002), O’Neill and Sarhan (2004), Poulos (2005), and others have described the effects that construction defects can have on the axial and lateral performance of drilled shafts. Our industry has seen rapid progress in recent years in the development and improvement of tools for detecting drilled shaft anomalies, such as gamma-gamma and crosshole-sonic logging, sonic-echo testing, thermal integrity profiling, and even visual inspection with invasive video cameras. Nonetheless, in most cases the wealth of data from these tests is used by foundation engineers to make a fairly “black or white” decision—should the defects be repaired, or should the shaft be rejected? A third option that is not typically considered is to directly analyze the section, including anomalies, and compare the reduced strength and/or ductility to the actual project demands. This option takes full advantage of the data collected during integrity testing, and may provide a justifiable means for avoiding further construction costs and delays, whether for repair or replacement."

Jan 1, 2016

By Arjan Jovani, Arjan Beqiraj, Përparim Alikaj, Altin Karriqi

"Koman dam is one of most important high dams in Drin River Cascade. Safety of these dam is very important not only in power production but also in social and environmental aspects connected with vital activity of local people living in downstream of Drini River and in economic development of the country. In December 2014, during the rehabilitation works on some protection measures at the downstream dam toe, a considerable amount of water leakage emerged from the dam toe. This was noticed even before, but its amount and physical-chemical properties were not evaluated. In order to study the origin and flow direction of this water leakage, KESH sh.a. (Albanian Power Corporation) realized Geophysical and Hydro chemical surveys, turbidity and flow measurements and respective analyses of them. Geophysical survey consist in Apparent Resistivity surveys and Self Potential survey. The survey was done in 3 lines using Resistivity “Real Section” technique. Results are plotted in Sections and plan maps of resistivity and SP parameter. There are defined possible leakage areas and the main flow directions are defined. Also, there is done a hydro chemical analyse. Nine water samples were taken from the different places as Komani lake, service galleries of dam, dam toe and two karst springs which were analysed for both physical-chemical parameters and isotopic composition of O-18 and D. The attained analytical data found that water from the dam toe leakages shows the same chemical signature and isotopic composition of O-18 and D as the water from the lake, thus confirming the hydraulic connection between them.Also, There is done the analyse of water leakage turbidity and amount of this leakage"

Jan 1, 2016

By M. Hesham El Naggar, Mehdi Heidari

"Equivalent fixed-base cantilever model is a common approach for performance base seismic design of bridge structures supported by extended pile-shaft. In this method, global displacement ductility factor is related to local curvature ductility demand by assuming a concentrated plastic hinge at location of maximum bending moment. Equivalent plastic hinge length is one of the key parameters that should be assumed accurately in kinematic expression of the cantilever model. Although, some expressions have proposed to estimate the length of the in-ground plastic hinge; however, these relations yield differing results. In this paper, a general expression is derived based on the concept of distributed plasticity to predict the plastic region of yielded piles in clay and sand. A length modification factor is defined to relate the equivalent length of plastic hinge to the real plastic zone. Then, results from nonlinear pushover analyses are used to propose an equation for the modification factor as a function of displacement ductility factor.IntroductionDuring severe earthquake events, development of the plastic hinge in pile foundation below ground level is inevitable for bridge structures supported on extended pile-shafts. A common approach for seismic design of the yielding pile-shafts is to replace the pile-soil system by an equivalent fixed-base cantilever assuming the equivalent system has the same global response as that of the pile-shaft (Budek et al. 2000; Chai 2002). In this method, plastic curvature is concentrated at the center of the equivalent plastic hinge below ground surface. Prior knowledge of plastic-hinge length is essential for proper assessment of assess plastic displacement at the top of the pile-shaft. Unfortunately, existing recommendations for estimating plastichinge length are largely incomplete and/or inadequate.During the last two decades, several relationships have proposed for evaluating the equivalent plastic hinge length, Lp, based on experimental and numerical studies. Budek et al. (2000) conducted numerical modeling to calculate the plastic-hinge length of piles embedded in cohesionless soil. They found that the plastichinge length varies linearly with both soil stiffness and aboveground height, e. Chai and Hutchinson (2002) conducted full-scale experimental tests on reinforced concrete piles in sand. They reported that Lp depends primarily on the aboveground height of the pile, neither sensitive to the soil stiffness nor to the value of displacement ductility factor. They stated that the equivalent plastic hinge length is relatively independent of the displacement ductility factor and is not very sensitive to the change in soil density. On the contrary, Goel (2014) and Liu et al. (2016) conducted nonlinear numerical analyses which revealed that Lp changes with the displacement ductility factor and even suggested that using different values of Lp for different seismic design levels is essential for a reliable estimation of the ductility capacity."

Jan 1, 2017

By Abhijit Saha

"Two analytical closed-form elastic-rigid-plastic solution methods to predict the rigid foundation behaviour on stone-column reinforced soil are compared, both of which takes into account the stone material yield within the host soil according to stress-dilatancy theory. These are the mechanistic methods developed by the author (2004, 2005) [that presently incorporates the dilatancy angle as per Schanz and Vermeer (1996)] and that developed by Pulko and Majes (2006), that takes into account the column yield as per Rowe dilatancy theory. Since optimal design of stone column necessitates optimum stress concentration on column, which is generally composed of dense gravel with/or without sand, the vertical stress on granular column is often close to its peak strength and the material dilates. To arrive at closed-form analytic solution to this complex soil-stone column interaction problem, some common assumptions like axi-symmetric soilstone column ‘unit-cell’, elastic host soil and rigid-plastic Mohr-Coulomb stone column material are combined with equilibrium and kinematic conditions. The results reflect the beneficial effect of dilatancy within the optimal range or techno-economic domain of area-ratio. The settlement predictions are compared with other analytical methods available in literature as well as with measured settlement reduction of stonecolumn reinforced ground at different subsoil conditions around the globe reported in literature.INTRODUCTIONStone columns or granular piles are frequently used in stabilization of soft clays, silts and loose silty-sands with large amount of fines. The majority of analytical methods assume infinitely wide loaded area with end-bearing columns having constant diameter and spacing that approximate to axi-symmetric conditions, and the approach is known as ‘unit-cell concept’. Several analytical solutions are available, and many of them (Aboshi et al; 1979, Balaam & Booker; 1981) are based on elastic approach considering the stonecolumn and surrounding soil as elastic materials. However, elastic methods give the ratio between the vertical stress in the column to soil (stress concentration factor) approximately equal to the ratio of constrained modulus of both materials. This ratio was found to be considerably higher than measured in the field and it is believed that elastic methods may overestimate the effects of stone columns on settlement reduction (Barksdale & Bachus, 1983). The elastic and elasto-plastic solutions presented by Balaam and Booker (1981, 1985) indicate that the problem can be idealized by assuming that the stone column is in a triaxial state and possibly yielding, such that there is no shear stress at the stone-soil interface and no yielding in the soil. Similar assumptions of stone column to be in a state of limiting equilibrium and under a triaxial stress state are considered in other methods also (Priebe; 1976, Van Impe & De Beer; 1983, Van Impe & Madhav; 1992, Saha & De; 1994, Saha; 2004, 2005, Pulko & Majes; 2006). In majority of the methods it is assumed that under load the stone-column yields at constant volume. However, the last three cases cited consider another parameter; the dilation of stone column. In Van Impe and Madhav’s (1992) and author’s (2004, 2005) method, the dilation is taken into account through the final value of the volumetric strain of column, whereas Pulko & Majes (2006) considered the stone column as Mohr-Coulomb rigid-plastic; dilating at yield in line with Rowe (1962) dilatancy theory."

Jan 1, 2015

By Chu E. Ho, Paul Napoli

A new waterfront park was developed on Long Island in close proximity to the East River and Newtown Creek. The existing ground consisted of fill over soft organic clay, medium dense silty sand, glacial till and schist bedrock. The ground was initially raised to preload the underlying soft soils to stabilize the ground in preparation for site development. The ground was subsequently cut down to temporary grades for installation of foundation piles for the overlook structures and construction of reinforced concrete cantilever retaining walls forming pathways located adjacent to the water bodies. The retaining walls were located in two rows at different elevations along the sides of a steep embankment. Where the pathways converge, some of the walls were too close to each other, and were redesigned as a combined U-wall with a common base slab. The individual retaining walls were designed for adequate bearing, sliding and overturning resistance. Ground anchors were installed to enhance global stability of the retaining walls. This paper presents the design considerations for the retaining walls for various loading conditions, and evaluation of the trial and proof tests for the anchors. INTRODUCTION The New York City Master Plan included the transformation of an approximately 30-acre parcel of land in Long Island City, Queens, New York from a former manufacturing zone into a residential, commercial and recreational zone for middle-income community. The site was located at Hunters Point South along the eastern shoreline of the East River and Newtown Creek (Figure 1). The development included low to high- rise residential buildings, a public school, and retail structures. Open spaces were provided along the East River and Newtown Creek waterfronts in the form of a continuous park providing for recreational and community-related activities. Waterfront structures included small park buildings, walkways and viewing platforms. The shoreline was surrounded by revetments as part of the flood mitigation strategy. The project involved extensive site re-grading and several retaining walls were constructed. The earthwork volume amounted to approximately 47,000 cubic yard of imported fill and 93,000 cubic yard of cut. The exposed height of the retaining walls ranged from 3 to 15 feet. This paper focuses on the design and construction of the retaining walls for the project.

Jan 1, 2019

By Gang Guo, Zhong Liu

"In response to an increasing demand of anchored structures for underground space and transportation infrastructure in China, an innovative underreamed ground anchorage system was created. The novel anchorage system has provided more efficient functions with higher capacity at lower cost, because of the enlarged cylindrical body (known as ECB) sealed in capsule at bottom of anchorage. This paper presents the detailed structure of innovative anchorage system and its special features. To investigate the bearing mechanism of new anchorage, we evaluate its performance and failure mode based on the experimental results, and also indicate its strain-hardening load-displacement relationship. Unlike the shaft anchorages, it is identified no overall failure to be found in soil surrounding the underreamed anchorage. More importantly, the anchorage capacity is governed by the base resistance, which takes more than 80% of total pullout capacity resulting from the contribution of ECB. Finally a case history of anti-floating project introduces the new combined construction approach and procedure, which has provided the contribution to the quality control and cost efficiency.INTRODUCTION AND BACKGROUNDThe construction boom over two decades in China has resulted in an increasing demand for underground space and slope stability. The infrastructures market requires the more efficient anchorage systems for retaining structures, resisting uplift forces and slope protection. The major concern focuses on gaining higher capacity and lower cost resulted from perfecting anchorage systems. There are three main anchorage systems designed to achieve the above objectives: ? single bore multiple anchorage system (Barley 1997), ? regroutable anchorage system (Smoltczyk 1991), ? underreamed anchorage systems (Xanthakos 1991). Generally, the concept ? comparing with the other two, can be more competitive due to its distinct advantages. To improve the performance and durability of ground anchorages under the complex geological conditions and diversified engineering requirements, a number of different underreamed anchorage technologies had been used, which included cone - shape anchorage described by Liao, Wu and Shu (1997) in Taiwan, Soilex anchorage developed in Sweden (Massarsch et al. 1997), Soletanche anchorage proposed in France, blasting anchorage used in Czechoslovakia (Hobst and Zajic 1986), jet-grouting anchorage innovated in Europe (Anon 1988), as well as deep mixing anchorage created in Japan (Cheng et al. 2000).The underreamed anchorage systems have the remarkable advantages compared to the shaft anchorage system. However, there are also some weaknesses inherent in the underreamed systems. For instance, the mechanical underreamed anchorage is unsuitable in sand or waterbearing ground, because the enlarged hole is easy to collapse, and it is hard to ensure the quality of anchorages. On the other hand, relying on the blasting in deep hole, the geometrical space and dimension of enlarged hole is uncontrollable, meanwhile, the continuous blasting operations may easily cause the serious ground deformation and the negative effects to the completed anchorages."

Jan 1, 1900