Search Documents

By F. E. Lathe

INTRODUCTION THE present study, based largely upon phase equilibrium diagrams and other theoretical considerations but nevertheless addressed primarily to the practical metallurgist, has been undertaken with a view to discovering what light can be thrown upon the role of alumina in slags. According to Liddell (23), "alumina apparently acts as .a base if much silica is present, as an acid if the silica is low, always as a nuisance." Newton and Wilson (26) state that .alumina "is never added intentionally, as it makes the slag viscous, and is generally an undesirable constituent of slags". Camp and Francis (3) sum up their views by saying, "alumina is seldom used intentionally as a flux, but it is present in nearly all raw material, hence unavoidable". One has only to read The Function of Alumina in Slags, by Henrich (I3), and the very extensive discussion that followed the presentation of his paper, to realize that, before the days of phase equilibrium diagrams, it was a very serious question indeed as to whether alumina should be calculated as a basic, acid, or neutral constituent. Opinions then differed widely, as well they might; today, even though no categorical answer can be given to the question raised, the function of alumina can be at least partly clarified by a study of the fundamental work done by the Geophysical Laboratory in Washington and by certain universities in both America and Europe. It will be a source of gratification to Canadian metallurgists and ceramists to know that work of this type is now under way in the recently organized Physical and Crystal Chemistry Section of the Mines Branch, Ottawa, and that results of practical value have in fact already been obtained.

Jan 1, 1951

By R. C. A. Thurston

INTRODUCTION THE deleterious effect of stress raisers or notches on the resistance to fatigue of machine components, and other parts subjected to repeated dynamic loading, has been well known for many years. Most engineers in the mechanical field have, at one time or another, encountered a shaft which fractured due to a poor transition fillet, a holding-down bolt which failed due to insufficient tightening or inferior thread form, or a fitted member which broke through a combination of fretting corrosion and clamping stresses. All of these are examples of the damaging influence exerted by stress raisers in fatigue. Other common forms of stress raiser which have taken their toll of dynamic components are: keyways, oil holes, splines, quenching oil grinding cracks, tool marks, and sharp changes in section; some are the result of the design, others of poor execution of the design. It is our experience in the Mines Branch1 and I feel sure this will be corroborated by other fatigue investigators, that the majority of failures are due to incorrect design or faulty preparation of the part concerned, rather than to the use of inferior material. Quite frequently, it is true that the operating conditions necessitate the presence of a 'notch', but even in such cases methods are generally available by which its adverse effect on the life of the component can be reduced or annulled. The purpose of this paper is to discuss a few typical stress raisers, and to provide information on various processes for mitigating their effects in fatigue.

Jan 1, 1951

By D. J. MacDonald

UNDERGROUND development at the Lynn Lake property of Sherritt Gordon Mines, Limited, was begun in 1948 with the sinking of the A shaft in the area of the A orebody. By June, 1949, the shaft was completed to a depth of 1,024 feet. Twelve stations were cut, with the bottom level at 992 feet below the collar. Since completion of the shaft, lateral work has been carried out on the 12th level in order to expose the known orebodies and to provide openings from which deeper exploration could be conducted. Dur¬ing the change-over from sinking to lateral work, preliminary diamond drilling was done from the 12th level station to locate the A? ore-body. Later, drilling was carried out from the 5th and 9th level sta-tions, where, also, the outline of the A orebody was established. As the work progressed on the 12th level, and with the commence-ment of drilling below that level, the geological picture was found to be complicated by numerous faults. Instead of operating two drills it became necessary to use at least four. The original plans had provided air sufficient to drive two headings and to operate two diamond drills. The addition of two more air-driven drills resulted in a serious shortage of power.

Jan 1, 1951

By T. G. Ewart

INTRODUCTION FOR THE purpose of this paper, western bituminous coal is defined as steam coal produced in Alberta and southeastern British Columbia for sale primarily to railways and industries. Before examining present and future markets of this industry, it is proper to review briefly financial and operating conditions within the industry. The report of the Royal Commission on Coal, 1946, supplies financial data from which some conclusions may be drawn. In 1944, the industry as defined above had share capital of $24,886,696. In the fifteen years 1930 to 1944, inclusive, the industry produced: 44,364,211 tons of coal. The profit on this tonnage amounted to $4,678,382.58, which represented 10.6 cents per ton of production. Miscellaneous earnings increased the amount available for dividends to shareholders to a total of $8,487,952.41, which is equal to, 19.1 cents per ton of production. Dividends actually paid in this fifteen-year period amounted to $12,332,040.64, which represented an annual average rate of 3.40 per cent on share capital. It is worthy of note that, in 1944, the net current position of the industry, including investments, was $8,753,874.51. The writer believes that the financial position of the industry with respect to capital, current financial position, and net earnings, has not significantly changed from the fifteen-year period out-lined above. The figures quoted indicate the following situation: (1) The western bituminous coal industry is adequately financed. (2) The industry has followed a conservative dividend policy and has accrued funds for contingencies. (3) The industry has sold its production at very reasonable prices as evidenced by its moderate earnings per ton of production.

Jan 1, 1951

By M. S. Fotheringham

Recognition of the Growing Importance of Iron and Steel Few Canadians have yet become aware that Canada's vast iron ore resources, the greater part of which is only now beginning to be developed, will inevitably have a profound effect on the entire Canadian economy, benefitting in some measure the lives of all Canadians. The great iron mining developments of Ontario, Newfoundland, Quebec, and Labrador are destined to make Canada one of the world's major producers and exporters of this material, on which our industrial civilization is?based. These developments will create new employment, new communities, new transportation facilities, and new investment opportunities. Iron ore is the foundation and the keystone of modern mechanized civilization. The most prosperous nations of the world are the highest per capita consumers of iron and steel, and in these countries the per capita consumption is increasing steadily despite the advent of light metals, plastics, and other competitive materials. Three-quarters of the human race have too little steel -and consequently too little mechanization -to provide for themselves the necessities and comforts of civilized living. Progressively they will demand, and acquire, the machines, the transportation and communication facilities now lacking, and they will win them by making greater use of the world's iron resources. It is the good fortune of this generation that Canada's 'iron age' is just getting well under way.

Jan 1, 1951

By E. J. Burrough

MR. J. J. McIntyre (International Coal & Coke Company, Ltd., and McGi1livray Creek Coal & Coke Company, Ltd., Coleman, Alta): Mr. Burrough's excellent paper, Metallurgical Coals of the Crowsnest Area, seems especially timely now, when the need for developing iron industries in the west, as well as in the east, is receiving so much attention. His -thorough review of the 'coking' industry is an especially valuable contribution, along with which the following brief remarks on coking in the Crowsnest Pass area of British Columbia and Alberta may be in order. When the Crowsnest Pass line of the Canadian Pacific railway was built there were great expectations for the non-ferrous metal industry; quite a number of smelter's were al-ready in operation in British Columbia and the northwestern United States, and further expansion was confidently expected. The suitability of the medium-volatile coking coals of the Pass for making metallurgical coke had been recognized from the time the fields were first explored. By the time the mines were fairly well developed there was already a market to war-rant the building of coking plants, and a common belief that expansion of the market would require a large coking industry. The first coke production was from plants built by the Crowsnest Pass Coal Company, Ltd., at Fernie, B.C. in 1903, and the International Coal and Coke Company, Ltd., at Coleman, Alberta. These plants were followed by others built by the Crowsnest Pass Coal Company, at Michel, B.C., by West Canadian Collieries, Ltd., at Lille, Alberta, and by Leitch Collieries, Ltd., at Passburg Alberta, and by a plant at Hosmer, B.C.

Jan 1, 1951

By T. B. Williams

A SEARCH of the records indicates that evidences of accumulations of petroleum and natural gas within the boundaries of British Columbia were discovered at approximately the same time as were those of Alberta. They probably would have been developed as soon bad it not been for the fact that they are in such uninhabited parts of the Province. Even today, the seeps of the Flathead area, and the later discovered extensive seeps of the Peace River area, have been seen by very few people. From the geological evidence, there is reason for believing that British Columbia soon will be a petroleum producing Province. Fifty-eight operators, both companies and individuals, are now backing the money and the effort which they have invested with us, for the most part within the last three years, in a belief that this is so. The promulgation of the Petroleum and Natural Gas Act in 1947 marked the beginning of a new phase with regard to the exploration and the development of our petroleum and natural gas resources. Since August 15th, 1947, the date on which the Act came into force, the area under exploration bas increased from a few thousand acres, held by lease under the Goal and Petroleum Act, 1986, to 10,460,115 acres, including all active permits, licences, and leases. In addition there are 192,720 acres under application, bringing the total under issue and application to 10,652,835 acres. The total area is comprised of 105 permits, 20 licences, and 26 leases under the 1986 Act. The permits and licences, which ?represent active exploration and development, are held by a total of 82 companies and 26 individuals.

Jan 1, 1951

By N. W. Hendry

ABSTRACT Exploration by geophysical methods and diamond drilling of an occurrence of chrysotile asbestos, located ten miles east of Matheson, Ontario, was commenced on March 25th, 1949, by the Canadian Johns-Manville Company, Limited. The asbestos is associated with a narrow sill-like body of basic and ultrabasic rocks which strikes northwesterly across portions of Munro and Beatty townships. To date, asbestos zones of commercial interest, many hundreds of feet in length, width, and depth, have been outlined by diamond drilling along a 2-mile length of serpentine. The fractures occupied by the asbestos veins are closely associated with the regional faulting in the area. The mining of the first occurrence, or A orebody, will be by open-pit methods. Milling will commence at a rate of 50 tons an hour. INTRODUCTION OCCURRENCES of chrysotile asbestos in Munro township have been known at least since 1914 and references to them appear in reports published by the Ontario Department of Mines in 1915 (1) and 1919 (2). J. G. Ross (3) in his excellent publication on Chrysotile Asbestos in Canada, mentions an occurrence in Munro township. The area was first mapped in detail by J. Satterly, of the Ontario Department of Mines, in 1944, and brief mention is made of chrysotile asbestos in Satterly's preliminary report (4), which was published the following year.

Jan 1, 1951

By F. Doxey

Introduction Numerous papers have been written dealing with the construction and functions of, and the environmental conditions created by, Diesel locomotives. Therefore, it is not my intention to attempt to deal with these phases of Diesel transportation other than to make reference to them in ?relation to and in connection with actual operation. The rapid expansion of industry during recent years and the necessity of products being made available at competitive prices in home and world markets has made the demand for cheaper coal a very serious factor for the coal industry. This condition has meant each coal producing country looking into ways and means whereby greater productivity and reduction in cost could he achieved. Surveys made show that, in addition to face mechanization, savings, in some cases substantial, can be made in transportation. Ventilation The most efficient mines are in-variably the well ventilated ones, for it is true that, where there is good ventilation, there are usually good roads. These combined factors are very essential where Diesel locomotives are used. Good roadways and track allow speed, and good ventilation dilutes rapidly any disagreeable exhaust gases. Locomotive Development In the older types of auxiliary rope haulage, coal hauled per haul-age hand is usually very low.

Jan 1, 1951

By B. W. Snyder

INTRODUCTORY THE earliest known case of transmission of natural gas by pipe lines was early in the Christian era when the Chinese used bamboo pipes to transport natural gas from surface seepages to heat brine for the recovery of salt. Since that time many materials have been used as conduits-hollow wooden legs, wood stave pipe, day tile, cast iron, and, finally -since about 130 years ago - steel pipe. Even then, this new material came into use rather . slowly for, as recently as 80 years ago, wood pipe was still being used. However, as techniques were developed to take advantage of the properties of steel, this material gradually replaced all ethers for the transportation of gas for longer and longer distances at ever increasing pressures. In 1912, one of the longest pipe lines of its size at that time was built-this was a 16-inch line bringing gas from Bow Island to Calgary, a distance of 170 miles. We have been able to find records of only two ether such lines at that time-one a 185-mile 16-inch line from Vivian, Louisiana, to Little Rock, Arkansas, completed in the summer of 1911, the ether a 280-mile line from West Virginia to Toledo, Ohio. This last ? mentioned line was reported in a magazine article of September, 1912, but no indication was given of its size on completion date. It is apparent, therefore, that modern high pressure transmission of natural gas is a technique less than forty years old.

Jan 1, 1951

By John Lund

INTRODUCTION GOLD-BEARING placers of Alaska and the Yukon Territories are buried under a layer of permanently frozen alluvial overburden, or 'muck', which varies in depth from twenty to one hundred feet. The placers, and the decomposed bedrock layers upon which they are deposited, are also permanently frozen. During the summer, surface muck which is exposed to the sun will thaw, but only to a depth of a few feet. To reach a valuable deposit, the frozen overburden must be either penetrated with shafts, or stripped from the deposit entirely. In either case, before the placer can be mined, it must be thawed. At modern dredging operations, the frozen muck is stripped from the placer by powerful jets of water from hydraulic giants. The placer, and several feet of decomposed bed-rock, are then thawed by forcing water through narrow pipes which have been driven into the deposit. Other methods of thawing frozen placers were used extensively during the early years of the Klondike 'gold rush', but experimentation later proved that creek water at its natural summer temperature was a more effective and economical thawing medium than any other which had been used. EVOLUTION OF COLD WATER THAWING Early prospectors of the far north reached placers by digging shafts through the frozen muck. They then thawed the placer sand and gravel by building wood fires at the bottom of the shafts.

Jan 1, 1951

By W. H. Miller

Introduction In this paper we have endeavoured to present a general description of the electrical applications underground at Copper Mountain, including types of equipment used, problems encountered, and methods by which they were overcome. No attempt has been made to outline in detail the wiring of various circuits. Until recent years, the main use of electrical energy underground at Copper Mountain consisted of direct current for locomotives, trolley systems, .and signal and communication circuits. The prohibitive cost of equipment and distribution systems prevented any extensive use of a.c. beyond that commonly used for essential lighting purposes. However, in 1943 the shortage of manpower and the increased cost of labour and supplies necessitated a general mechanization programme.

Jan 1, 1951

By R. R. Rogers

ABSTRACT The experiments described demonstrate that crude commercial lithium containing in the order of 0.5 per cent sodium can be refined, the resulting metal containing as low as 0.001 per cent sodium. During the process, the metal is vaporized and condensed at a gauge pressure of less than 0.04 micron. Considerable operating data and a detailed description of the experimental equipment are included. INTRODUCTION DUE TO THE unusual properties of lithium metal, its use is likely to increase considerably during the next few years (1, 2). This is of particular interest to Canadians because there are important deposits of lithium-containing minerals, especially spodumene, in Canada and it is hoped that lithium compounds and lithium metal will be produced from these deposits in the fairly near future. In order to assist in the development of this industry, the Mines Branch of the Department of Mines and Technical Surveys has initiated a programme of research in lithium metallurgy. In 1948, a paper (4) was published on methods of producing lithium metal and its alloys. Data on the corrosion resistance of some lithium alloys were included. In 1949, a paper (3) was published which showed that the addition of a small percentage of lithium to zinc anodes used for cathodic protection will improve their usefulness under certain circumstances.

Jan 1, 1951

By L. O. Cooper

IN THE operation of most mines, hoisting ropes, made of steel, play a very important part in the conveying of men and material between surface and the underground workings. It is obvious that, in order to maintain a maximum degree of safety, certain restrictions must be placed on the loads that may be carried by hoisting ropes, as well as on other factors that may affect the life of the rope. It is the purpose of this paper to suggest ?a new method of defining the necessary restrictions. The three main stresses in a hoisting rope are the static stress, bending stress, and dynamic stress. Crushing stresses, which are also present, are largely indeterminate and may best be allowed for by proper grooving of drum and sheaves, by adequate inspection of cross-over points, and by limiting the number of layers on the drum. They will, therefore, not be considered in this analysis. In the ?recent Ontario regulations, the limiting conditions for the main stresses are specified separately. The static stress is limited by setting a minimum static safety factor of 5.0 The dynamic stresses are allowed for by specifying a minimum capacity factor of 8.5, which has the effect of increasing the safety factor required at smaller depths in a uniform manner. The bending stresses are limited by calling for a drum-dia./rope-dia. ratio of at least 60 for ropes up to 1 inch in diameter and 80 for ropes greater than 1 inch in diameter. One disadvantage of this method is that the controls are too rigid and do not allow the operator sufficient freedom of action within safe limits.

Jan 1, 1951

By Evans B. Mayo

ABSTRACT Orange Footwall 'sill' is locally concordant locally discordant, with the structure of its sedimentary walls. The sediments were folded in two directions. Folds, following both these directions, are preserved in the concordant portion of the 'sill'. It seems, therefore, that the porphyry has replaced the sediments, thus preserving within itself their structure. During replacement, the nascent porphyry may have been much weaker than its walls. Accordingly, under directed pressure, the porphyry could have flowed locally, disarranging the replaced structures within it and developing a flow structure discordant with the folds in the sediments. Some such action may account for the discordant parts of the 'sill'. INTRODUCTION The senior author has seen certain granitoid massifs that have an internal structure vastly different from, and discordant with, the structures in their wall rocks. It seems that? such massifs have moved independently of their surroundings. Yet, a structure section elsewhere in the same mountain range may reveal granitic rocks with internal structures that appear to continue the structure of the invaded rocks. In such a case, it is at least thinkable that the granite has replaced the older sediments or volcanic rocks. In February, 1950, the writers mapped, on 15 level of the Nickel Plate mine, near Hedley, B.C., a diorite or gabbro porphyry 'sill' that, in one cross-cut (1503), appeared to be quite concordant with the wall-rock structures, whereas in another cross-cut ( 1500) about 100 feet to the south, the same porphyry was discordant (see Figure 1).

Jan 1, 1951

By J. A. Harle

Introduction When considering power in Alberta, there automatically come to mind ideas of either hydro or thermal generation, leaving in one's thought an uncertainty as to which one would propose. There is frequently an obvious source of power in some locations on our fastflowing rivers, the major possibilities being described in the report on Surface Water Supply and Water Power of Alberta issued by the Alberta Government in 1948, but it must be realised when reading that report that the sites so described will require extensive geological and other surveys before they can be exploited, and account must be taken also of the transmission distances involved in each instance. From a conservation point of view, where water power can be economically developed and power transmitted to the load centres, this should be done, and our thermal resources should be husbanded for our coming generations, especially if our water resources are falling owing to glacial shrinkage.

Jan 1, 1951

By E. J. Burrough

Coal Reserves The Crowsnest Pass coal fields form part of a greater area which comprises the Inner Foothills belt of the Alberta coal fields and the southeastern coal fields of British Columbia. The most valuable and most extensive reserves of the bituminous coals of Canada are concentrated in this?area, of which the Crowsnest Pass fields form an important part. The extent of these coal reserves together with those of the rest of Canada were recently studied by the Geological Survey of Canada for the Royal Commission on Coal of 1946 (1). Quotin from the report, it is of interest to note that, prior to this work, the most widely known, and in fact the only Canadian-wide estimates of, coal reserves of Canada available to the Commission were those prepared by Dr. Dowling in 1913 (2). At that time it was estimated that Canada's reserves of coal were over twelve hundred billion tons. The more recent estimates of mineable coal for the whole of Canada are of the order of 10 per cent of that figure and are reported. as 99 billion tons, which is further reduced to 40 billion tons on the basis of the estimation of recoverable coal. This considerable divergence in estimated reserves is explained in part by the big difference in the bases of measurements. For example, in the original report, seams of one foot occurring at a depth of 4,000 feet were included in the estimates.

Jan 1, 1951

By J. E. Hawley

Abstract Spectrographic methods for the analysis of minor constituents such as platinum-group metals, gold, silver, and silica in palladium and platinum refinery sponge are described. These involve the conversion of the sponge metals to the black form by reduction with high purity aluminum filings in either acid or alkaline media. Standards of known composition are prepared in the same manner from either refinery or spectrographically standardized sponge metals. Samples of the black metals are mounted in pellet form and a multisource spark discharge used for excitation. The range of concentrations of impurities studied are those common to refinery samples. Excellent reproducibility of intensity ratios using major constituents as internal standards, is demonstrated and two methods have noted by which the accuracy of the procedures are shown to be of the order of 3 per cent, on the basis of synthetic preparations. Introduction During the past two years an investigation has been carried out in the Spectrographic Laboratory, Queen's University, to determine the suitability of modern spectrographic techniques for the precise analysis of the platinum-group metals palladium, platinum, rhodium, iridium, and ruthenium in the form of refinery sponge analyzing about 99 per cent of the major constituent.

Jan 1, 1951

By A. G. Lylie

Introduction At the Britannia Mining and Smelting Company's mill, the equivalent of 2,500 to 2,800 pounds of copper sulphate crystals per day is made from copper which is precipitated from the mine-water. This copper sulphate is used in the mill for the recovery of sphalerite by2 flotation. From 1932 until 1936 it was produced by exposing the precipitate to air for thirty days and then dissolving the oxidized copper with dilute sulphuric acid. In 1936, the flotation of sphalerite was discontinued and, when it was resumed in 1947, steps were taken to try to improve the former method. The present paper outlines the way in which this was done, and describes the plant and procedure by which copper sulphate is now being made, and by means of which an appreciable saving is being effected. Aboratory Tests The previous work had established that the precipitate, which consists mainly of metallic copper, must be oxidized before the copper would dissolve in dilute sulphuric acid. Various methods for oxidizing it were tried but in the early laboratory work the only suitable one found was to heat the precipitate to 600°C. and hold it at this temperature for two hours. When this was done, approximately 90 per cent of the copper became soluble in .acid. This percentage was considered satisfactory for practical purposes, but the cost of roasting was prohibitive because only a small amount of roasted precipitate was required each day.

Jan 1, 1951

By J. C. Heaslip

Introduction The greatest single advance in rock drilling practice since the advent of percussion drills was the introduction of tungsten carbide tipped rock drill?bits. The evolution of rock drills has been a long and highly diversified effort which has culminated in the highly refined ?drilling machines we know today, but because of the spectacular possibilities shown by ?detachable bits, and especially those with tungsten carbide inserts, there is little doubt that the cutting face of .the drilling unit has in recent days stolen the spotlight of rock drilling research and commanded the major attention of the rock drilling fraternity. "Solid" Steels Until about twenty years ago, all rock was drilled with a one-piece rod with a bit forged on one end. In the early years of the art of rock drilling, there was tried every conceivable pattern of :bit from the single-edge chisel to elaborate geometric 'designs. In the end, it was found that a 4-point bit with two sharpened cutting edges crossing each other at right angles would serve best for most rock drilling requirements. For some years thereafter, the main concern of drill manufacturers was .to obtain the best possible steel for drill rods. This was not accomplished as easily as might be thought. The cutting end had to be such that it could be hardened sufficiently to do its work without premature dulling and yet not so brittle as to shatter under the multiple impacts.

Jan 1, 1951