Search Documents

By R. H. Pemberton

"THE Mattagami district of Quebec has, during the past few years, experienced intense exploration by virtually every mining company operating in Canada. As a result of this activity, a number of well-mineralized zinc-copper bearing bodies have been found, some of which will almost certainly go into production. Much of the area has undergone what is now termed ""Saturation Prospecting"" or intense and detailed geological and geophysical surveying, followed by the drilling of nearly all possible bets. Considering only the airborne geophysical surveying, some blocks of ground have been flown by virtually every geophysical instrument which has to date been installed in an aircraft. A list of these different geophysical instruments would include: l. Fluxgate-type total field magnetometers 2. Vertical field magnetometer ,3. Nuclear-precession magnetometers 4. Single-frequency out-of-phase electromagnetometers 5. Dual-frequency out-of-phase electromagnetometers 6. Horizontal component measuring electromagnetometers 7. In-phase and out-of-phase electromagnetometers8. Dip-angle measuring electromagnetometers."

Jan 1, 1961

By Nathaniel S. Scott

Caland Ore Company Limited, a subsidiary of Inland Steel Company of Chicago, Illinois, leased an iron ore deposit from Steep Rock Iron Mines Limited on January 1, 1953.. This deposit lay underneath a lake and was covered with 161,000,000 cubic yards of Jake bottom material, mainly silt. Removal of this material was done on a contract dredging basis. This contract was divided into a plant phase and an operating phase. The plant phase consisted of supplying two cutter-type suction dredges, each with two booster pumps in the discharge lines. All six pumps were centrifugal, had 36" discharges and were powered by 10,000 horsepower electric motors. Peak demand was 59,157 kilowatts. One hundred and forty miles of steel tower line were built to bring power to the site. The balance of the plant consisted of tugs, 12 miles of discharge line, varying from 36" diameter to 42" diameter and attendant land-based equipment. A number of interesting dams were constructed

Jan 1, 1961

By Kenneth M. Haley

THE development of Reserve Mining Company's pelletizing practices began in 1949 in a pilot plant located at Ashland, Kentucky. Three years later the participating companies -Armco Steel Corporation, Cleveland Cliffs Iron Mining Company and Republic Steel Corporation concluded the work and the small plant was shut down. Oglebay Norton and Company was the operating manager and Armco Steel Corporation furnished labor and services. Arthur G. McKee and Company were the designers and constructors. The equipment flow sheet that was employed in that pilot operation is shown in Figure 1. This was Reserve's first step from the laboratory work per-formed by the Mines Experiment Station of the University of Minnesota in developing a commercial operation. The plant used New York state concentrate, purchased from Jones and Laughlin Steel Corporation's Benson Mine. This concentrate, minus 14 mesh, 64.3 per cent Fe, 5.7 per cent Si02, was processed at Ashland to 80 per cent minus 325 mesh in conventional ball mill, classifier, thickener, filtering

Jan 1, 1961

By Lionel A. York

THE first application of the cementation process took place in the year 1864, according to H. Standish Ball, when a break in the brickwork lining at a depth of 270', in one of the Rhine Preussen pits near Homburg, was sealed by running in milk of cement from the surface by means of a small hand pump. At about the same time Monsieur Portier adopted the method in France for repairing breaks in shaft lining. Figure 1 is descriptive of the Portier system and is of interest when compared with modern practice. During the next thirty years numerous attempts were made to improve the process; the general method used in sinking being to put clown bore holes outside the perimeter of the shaft for the purposes of injection. The cementation process was first recognized as an important as-set to mining in 1896 when Monsieur A. Francois developed his method of boring and injecting inside the shaft below the permanent water level. The Francois cementation process rapidly attained fame on the Continent and many shafts were sunk by its use in France, Belgium and

Jan 1, 1961

By C. H. G. Bushell, G. Brown, C. J. Krauss

1N FLOTATION, copper sulphate is used universally for the activation of sphalerite and marmatite and, to some extent, for the activation of other minerals. The copper activated surface readily adsorbs standard collectors such as the xanthates and dialkyl dithiophosphates whereas untreated zir~ sulphide does not. With the host of reagents available, making a mineral float is seldom difficult. The problem is to achieve selective flotation. In zinc flotation, the great value of copper sulphate results from its ability to activate zinc sulphide preferentially to gangue minerals. At the Sullivan Concentrator of The Consolidated Mining and Smelting Company of Canada Limited, the most abundant gangue mineral in the lead-zinc ore is pyrrhotite, and the zinc mineral is marmatite of somewhat variable zinc to iron ratio. For this Cominco study, selectivity between marmatite and pyrrhotite was therefore the most interesting aspect of copper sulphate activation.

Jan 1, 1961

By G. A. Gross

DURING the past 5 years a large amount of money and effort has been expended in exploration of iron-formations and in testing their suitability for beneficiation. Beds of ferruginous material are numerous and widely distributed in the Precambrian rocks of Canada and practically all of the known iron ranges or belts have been examined to a limited degree at least in an effort to evaluate their potential as sources of iron ore. A number of favorable beds have been selected for mining on completion of surface sampling, diamond drilling, extensive metallurgical testing and economic studies, and many other ranges are being studied. There are still a great many iron-formations that have not been evaluated by modern concentration methods and their regional extent is not fully known. The iron-formations are easily located by airborne or ground magnetic surveys but the main task in finding a mineable ore-body of this type amounts to locating a bed sufficiently large for mining which consists of material that can be concentrated economically by modern beneficiating methods. The ease with which an iron-formation can be concentrated to give a marketable ore depends primarily

Jan 1, 1961

By H. W. Fleming

In 1955, the results of a regional, geological interpretation of the northern portion of New Brunswick were used as a basis for selecting, for intensive exploration, three areas in which structural and stratigraphic conditions were believed to be favourable. Airborne electromagnetic work, in one of these areas, provided the justification for acquiring the Murray group. Even though the initial results were discouraging, this geological interpretation, combined with the fortuitous discovery of cop• per-bearing float, was sufficient reason for carrying out further work using geochemical methods. This work finally resulted in the discovery of the Murray massive-sulphide deposit, after about eighteen months of coordinated exploration on the property. While this deposit is a typical New Brunswick-type base-metal occurrence, extensive leaching has produced a fossil gossan that rendered it an elusive target for exploration techniques of limited penetration Full credit for localizing the target area is given to the geochemical techniques, but geophysical surveys were needed to provide the necessary

Jan 1, 1961

By R M. Ennis, J. C. Botham

This paper is one of a series pre-pared to study the role of fuels and reductants in metallurgical processes, especially from the viewpoint of Canadian requirements. The object of these studies is to provide a reason-ably authoritative interpretation on the interrelation of fuels in light of the considerable changes that have taken place in the Canadian energy field during the past few years. Previous papers in this group have dealt with the problem generally, and specifically in terms of the development of the iron and steel industry of Western Canada. These latter papers, presented at the Symposium on Iron and Steel in Western Canada held in Edmonton, Alberta, on September 8-9, 1959, surveyed the ferrous processes of interest for use in Wes tern Canada, especially with regard to solid fuel requirements. At that time it was evident that there was a need for a similar study of the fuels aspect of the non-ferrous metals industry.

Jan 1, 1961

By R. M. Porter

PILLAR extraction at the Sullivan Mine bas been in progress for over twenty-five years and bas .involved progressively larger pillars. The largest pillar blasted to date exceeds one million tons and is described in this paper. This blast is believed to be one of the largest to take place entirely under-ground. The Sullivan Mine, owned by The Consolidated Mining and Smelting Company of Canada Limited, is located in the southeastern corner of British Columbia on the east flank of the Purcell range overlooking the twenty-mile wide Rocky Mountain Trench (Figure 1). The orebody is a bedded replacement deposit in argillites, varying in thickness up to 300 feet, but averaging about 80 feet. Above the 3900 Level, the dip varies from nearly horizontal to 40 degrees; be-low the 3900 Level it varies from 45 to 20 degrees (Figure 2). Pillar extraction follows a plan of retreating outward from caved areas. The size of each blast is determined by the effect which the removal of support

Jan 1, 1961

By M. H. Cullender

THE determination of the flow characteristics of gas wells depends upon the analysis of pressure data obtained under shut-in conditions and under one or more known flow conditions. These data are commonly referred to as back-pres-sure test data, and I know you are all familiar with the back-pressure equation where, Q rate of flow, Mcfd @ standard conditions C coefficient of the back-pres-sure curve P 1 formation pressure, psia P • sand face flowing pressure, psia P2 (psia)2/1000 n exponent of the back-pres-sure curve Figure 1 is a graphical presentation of the back-pressure equation; the coefficient is the rate of flow at a difference in squared pressures of 1, in this case 2250 Mcfd, and the exponent defines the manner in which the rate of flow changes with a change in the difference in squared pressures. In Figure 1, the exponent of the back-pressure curve is 0.554 which means that for a 10-fold change in the difference in squared pressures, there will be a 3.58-fold (10 raised to the 0.554 power) change in the rate of flow.

Jan 1, 1961

By J. S. Kirkaldy, W. J. Slater, G. R. Mason

Activation analysis for copper and manganese in 10 mg samples machined from aluminum-base diffusion couples has been used in the study of ternary diffusion in the Al-Cu-Mn system. The accuracy, economy and convenience of the method are considered to be very competitive with other methods for analysis of such small samples. Neutron-activated aluminum-zinc alloys in the range from 10 per cent to 100 per cent zinc have been equilibrated with a known volume and the vapors subsequently condensed and collected. The vapor pressures relative to pure zinc (the thermodynamic activities) have been determined at 550°C' by recording the relative count of /'-rays from zn65 in the collected samples. The method is a sensitive one, although subject to serious obstacles to experimental accuracy.

Jan 1, 1961

By J. D. Corbett

The spatial coincidence of the seven anomalies is obvious, even though the self-potential is offset northward. Because the ratio, as an indicator of conductivity, is a relative estimate at best, concise interpretation is limited in almost every instance to the location of a conductor or conductor axis. When related to the initial phase of an exploration program, magnitudes and ratios similar to those obtained from any one of the methods described, would be sufficiently attractive to warrant further investigation. The compilation shown is an empirical comparison of actual field results and no emphasis has intentionally been placed on the relative merits of one method in respect to another. Too many additional factors, i.e., size, depth and conductivity of overburden, etc., that cannot unequivocally be answered, enter into such a comparison before a relative evaluation can be made.

Jan 1, 1961

By D W. MacFadgen

THE operating advantages of the longwall retreating system of mining, as opposed to longwall advancing, have been well known for many years. Although retreat walls have been successfully worked in the past in some of the collieries of the Dominion Steel and Coal Corporation in the Sydney, Picton and Cumberland areas, the adoption of longwaIl retreating as the general sys-tem of mining has not been attractive in the Sydney field, due to the time and expenditures required to drive roadways to the boundary. In addition. difficulties in maintaining effective ventilation on the faces, especially under conditions of low barometer, have made the operators in the field hesitant to adopt this as the general system of mining. The development of a machine capable of rapid entry drivage has made possible the driving of the necessary road ways to the boundary at a moderate cost, completely changing the picture and making a retreat system more attractive.

Jan 1, 1961

By M. E. Charles

The use of water flowing as a lower layer to reduce pressure gradients in petroleum pipelines was investigated using 17.5 deg. A.P.I. Lloydminster crude oil in a 1-inch laboratory pipe-line and a 21h-inch field pipeline. The method was found to be very effective in reducing the pressure gradient below that for the oil flowing alone. The factor by which the pres-sure gradient was reduced varied with the percentage of water added, and in general exceeded 10 for water contents ranging from 40 to 60 per cent. Within this range of water content the pressure gradient reduction factor was independent of the oil flow rate.

Jan 1, 1960

By Norman R. Paterson

"Under certain conditions useful gravity information of a reconnaissance nature can be obtained with-out measuring elevations by spirit level surveys on the ground. Gravity surveys can become part of a practical exploration program where high cost and slow progress previously hindered their utility. The advantages of the new elevation procedures are realized mainly in remote areas, in areas where ground transportation is slow and difficult and on surveys where the station spacing is large in comparison with the distance of the average optimum level shot. To utilize the advantages, transportation by helicopter or light plane is usually necessary. Methods of obtaining elevation control without leveling include: barometric altimeter survey; photogram-metric -APR spot determinations; methods involving the measurement of gravity gradients. The accuracies of these methods have been tested and compared with the normal accuracy of level surveys. It is felt that each method has its place in reconnaissance gravity work, particularly in the open areas of Northern Canada."

Jan 1, 1960

By J. Olaf Sund

"THE November issue of the Bulletin carried in it ""Origin of the New Bruns1viclc Gypsum Deposits"" by J. Olaf Sund. This paper was a digested account of a Master's thesis at the University of New Brunswick which was a very useful compendium of information of gyp-sum in New Brunswick. It was a warded the President' s Gold .Medal and the First Prize in the Graduates' Section of the Students' Essay Competition. The present writer presents his congratulations to the winner of the competition. At the same time he must comment on the use of certain terms and on certain conclusions presented in the paper.The term ""unconformable"" has been used in several places in the paper to describe the relationship of gypsum to anhydrite in various deposits in New Brunswick in a sense which is quite alien to the accepted meaning. It has long been known tl1at the gypsum at the surface or near the surface in deposits in the Atlantic Provinces has come from hydration of anhydrite by surface and ground waters. The gyp-sum must be looked upon then as an alteration or even a weathering product. It cannot in this sense be called ""unconformable"" and thus arguments using the word in the accepted sense are invalid."

Jan 1, 1960

By G. Bridgstock, S. S. Forbes, E. M. Elkin

"OPERATIONS at Canadian Cop-per Refiners Limited, since the refinery was established in 1931, have been described in previous papers ( 1,2). Since then the refinery has treated the entire copper output of Noranda Mines Limited and Hudson Bay Mining & Smelting Company Limited. With the commencement of production in 1956 at Gaspe Copper Mines Limited, this copper has also been refined. From the start of operations to the end of 1958, the following had been refined: copper, silver, gold, selenium and tellurium.Construction of new buildings and additions to other buildings have been needed to handle increased receipts. The refining capacity has been increased from 112,000 tons of copper per year to a total of 236,000 tons per year.The refinery is located at Mont-real East, Quebec, close to railway and highway facilities. Incoming materials and shipments, with some small exceptions, are handled by rail. Some finished products are sl1ipped by industrial flatcar to the adjoining plants of Canada Wire & Cable Company Limited and Noranda Copper & Brass Limited."

Jan 1, 1960

By R. M. Lauer

OVER THE YEARS concentration of the Sullivan ore has become progressively more difficult as the ore has become increasingly refractory. The introduction of new reagents and changes in the flow of the concentrator have been and continue to be necessary in order to maintain and improve the efficiency of metal extraction. Prior to the completion of the pilot mill in 1957 ail new ideas were developed in laboratory equipment. If these were found to be promising, there was no alternative but to introduce them directly to the main mill flow in one step. When a major change was involved there was always the possibility of serious losses while the mill was being adjusted to the changed conditions. It proved difficult to determine whether these losses were the result of the changed procedure or of failure to adjust the flow to a change in the condition of the ore during the test. The pilot mill has provided a valuable intermediate step between the laboratory and the mill. It avoids the losses which occurred when unsuccessful full-scale tests were attempted, and conversely it provides assurance that full-scale flow changes can be made without serious hazard.

Jan 1, 1960

By William D. Macdonald

The Upper Devonian Kettle Point black shale of southern Ontario is poorly exposed. Structural maps pre-pared from the data of numerous wells show that the upper surface of the formation has low regular relief, and that the lower surface reflects domes in the Middle Devonian and also local subsidence of the Devonian rocks due to solution of salt in the Silurian Salina Formation. The appearance of minor amounts. of marcasite, pyrite, and calcite, m that order, as interpreted from the evidence of concretions from the type locality at Kettle Point is thought to have been influenced by a rise m the pH within anaerobic sediments preceding compaction.

Jan 1, 1960

By C. Stamberg, W. McGuire, R. C. Carlson, L. W. Vollmer

"The selection of materials and pre-cautionary measures for handling natural gas and condensate containing aqueous hydrogen sulphide are presented. Based on the results of a pilot production test and laboratory studies, together with several years . of operating experience, it was found that the behaviour of materials in sour gas environments can be predicted sufficiently accurately for engineering purposes.The selection of proper materials is essential for preventing sulphide-stress cracking. Where high strength materials are not required, low car-bon steel is used. Components requiring high tensile strength and hardness characteristics should be made from K-monel or properly heat-treated carbon-manganese-molybden-um and AISI 4140 steels. Welded connections are a potential source of sulphide-stress cracking. Consequently high quality welding and strict inspection are suggested as the most economical precautionary measures available.A maintenance program based,. where possible, on visual inspection of equipment and/or test spools located at strategic points should be used to follow weight loss and putting corrosion in sour gas environments. If severe weight loss or pitting corrosion is encountered, inhibitors have been found to be an effective deter-rent."

Jan 1, 1960