Search Documents

By Christopher A. Jacobs

Project managers aim to maximise the NPV of their projects, but don't always appreciate the relationship between mine throughput, project value and the discount rate being used to evaluate their projects. Rate of production or throughput is perhaps one of the most crucial decisions a project manager must make, but if this choice is made arbitrarily, much effort may be spent on a feasibility study that does not optimise project value. The timing of the study in relation to the stage of exploration is examined and simple techniques are presented that project engineers and managers can use to home in on a production rate which will give their project the greatest chance of success.

May 1, 2006

By E. Nejati, S. Khoshkooei, V. Firouzdor, M. Akbari, F. Khomamizadeh

In this study the effects of Si content on mechanical and thermal fatigue properties of Al-Si casting alloys were investigated. Repeated heating and cooling cycles were applied on the samples at 230°C to develop thermal fatigue cracks. Crack growth mechanisms and microstructural influences were investigated by optical and scanning electron microscopy. Thermal fatigue behaviors were improved successively by increasing of silicon content up to 7wt%. However, addition of more than 9wt% silicon decreased the thermal shock resistance of the alloy. Silicon contents of about 9wt% presented the best mechanical and thermal fatigue resistance in the alloy.

Jan 1, 2006

By J. A. Jr. Carpenter

Expanding world economic prosperity, probable peaking of conventional petroleum production in the coming decades and environmental concerns require efforts to increase the efficiency of, and the development of alternatives to, petroleum-based fuels used in automotive transportation. In January 2002, the U.S. Department of Energy (USDOE) and the U.S. Council for Automotive Research (USCAR) of the "Big Three" traditionally-USA-based automakers, DaimlerChrysler, Ford and General Motors, formed the Freedom Cooperative Automotive Research (FreedomCAR) Partnership to fund high-risk, high-payoff research into advanced automotive technologies with the potential for eventually lowering the USA's nearly complete (95%) dependence on petroleum, 55% imported, for its transportation fuels. FreedomCAR replaced the Partnership for a New Generation of Vehicles (PNGV) which existed from 1993 to 2001. In January 2003, the energy-supply industry joined with the FreedomCAR Partnership forming the FreedomCAR and Fuel Initiative (FC&FI) to develop the technologies needed for the mass production of fuel-cell vehicles using hydrogen as fuel and the infrastructure needed to deliver the hydrogen to the consumer. The goal is to enable the automotive and energy-supply industries to make commercialization decisions in 2015 on large-scale introduction of such vehicles and on developing the infrastructure beginning in 2020. In addition to work on fuel cells and hydrogen infrastructure, the FC&FI conducts research on technologies with the potential for nearer-term energy efficiency and environmental benefits, such as new engine concepts, lightweight materials, and engine-electric hybrid propulsion systems. Lightweighting is seen as crucial for shorter and for longer term benefits because hybrid and fuel-cell powertrains are expected, at least in the early stages of adoption, to be heavier and more costly per unit of power than the standard internal-combustion, gasoline- or diesel-fueled powertrains they replace. Research and development (R&D) on casting of aluminum automotive components were major parts of the PNGV and R&D on casting of magnesium automotive components have been and are so under FreedomCAR. This presentation will review those efforts.

Jan 1, 2006

By J. F. Nie

Mechanical properties of precipitation hardenable magnesium alloys depend critically on the chemistry, structure, morphology, orientation and distribution of strengthening precipitates. It is therefore important to gain an improved understanding of these information and their correlations with mechanical properties. Our recent studies indicate that additions of 1-2 wt% of Zn to a Mg-6wt%Gd alloy result in a substantial enhancement in precipitation hardening and in creep resistance. If the strength and creep resistance of the resulting ternary alloy are to be further enhanced for commercial applications, then a detailed characterisation of the strengthening precipitates in these alloys is required. In the present study, the precipitates formed in a Mg-6Gd-1Zn-0.6Zr (wt%) alloy, peaked aged at 250°C, have been characterised in detail using transmission electron microscopy and 3-dimensional atom probe field-ion microscopy. It is found the peak-aged microstructure contains a dense and uniform distribution of precipitate plates that form on the basal plane of the matrix phase and are typically less than 1 nm in thickness. Detailed analyses of the structure and composition of these basal precipitate plates will be presented and discussed in the context of previous work on other Mg-RE¬Zn alloys of similar compositions.

Jan 1, 2006

By M. Kolahdoozan, H. Noori

"Molybdenite flotation at the Sarcheshmeh Copper Complex has been studied as a function of pulp potential controlled using two types of sodium sulfide (mineral and chemical origin). Air and either plant or laboratory nitrogen was used as a flotation carrier. Potential measurements were taken in the rougher cells as it was proved to be vital for molybdenite flotation. Flotation test with reducing potentials between -525 and -575 mv gave the highest molybdenum recovery (93%) and the lowest copper recovery of between 4 to 15% can be achieved. These potentials did not change considerably by adding increasing amounts of sodium sulfide. At more oxidizing potentials, i.e. more than -450 mv, the recovery of copper increases while the recovery of Molybdenite drops.INTRODUCTIONThe average copper ore feed grade to the Sarcheshmeh flotation circuit is typically set at about 1.2% Cu. to be delivered to processing unit is set at 1.2%. There is no control of molybdenum (Mo) which usually varies between 0.01 and 0.04%. During concentration, a Cu-Mo concentrate is produced by one stage of roughing, one stage of scavenging and two stages of cleaning. Final concentrate contains 0.5% of Mo and 32% of Cu while the particle size is 90% under 42 microns (325 mesh). Because of the high grade of Mo in this concentrate and economic interests, a molybdenite flotation circuit plant was built in 1984. This plant was designed to treat 1432 tons of Cu-Mo concentrate (on dry basis) and consists of one stage of roughing followed by seven stages of cleaning. After dewatering the concentrate contains 53.7% Mo which is dried and shipped overseas.The majority of molybdenite production worldwide comes as byproduct of copper porphyry ores. The Mo grade typically varies between 0.01 and 0.06% and accompanies chalcopyrite and chalcocite. Due to the hydrophobic nature of molybdenite, it can be floated along with copper sulfides. Thus the overall concentrate of Cu and Mo contains 0.2-1% of molybdenum as well as 20-42% of copper. To separate the Mo, Cu and Fe minerals, depressants are used. The most important of which are sodium sulfide, sodium hydrosulfide, Anomal D, sodium cyanide, ferropottasium and ferro-cyanide. The first three regeants have been extensively used for successfully treating porphyry ores [1]. In the molybdenum plant of the Sarcheshmeh Copper Complex only sodium sulfide has been used to date."

Jan 1, 2006

By L. I. Kiss, S. Perron, S. Poncsák, A. Perron

Aluminium industry has an increasing interest in the diminution of the energy consumption of the Hall-Heroult process by the reduction of the anode bottom covering with gas. Electrically isolating carbon-dioxide bubbles, produced at the anode, increase the ohmic resistance of the cell. As the gas production rate is determined by the applied current density, anode covering can be decreased only by a faster evacuation of the gas from the inter-electrode space. Among others, the inclination and curvature of the anode bottom promotes the release of the bubbles and thus decreases the mean value of the covering. Indeed, anode, insert in the molten cryolite bath has a square shape with horizontal bottom. However, inhomogeneous anode consumption, electro-erosion, bath circulation and the inclination of the bath-metal interface modify this shape gradually during electrolysis. Anode bottoms become inclined with rounded comers. This concentrates the gas generation to the center zone of the anode. As the bubble layer cannot be observed directly because of the hostile environment and the opacity of the bath, real scale air-water systems are used to study the impact of the anode geometry on the anode covering and the bubble induced flow. However, the physical properties of such a system are different than that we can found in the real cells. A simulator using the Lagrangian description of the bubble layer has been built and presented in earlier papers. This tool was used to investigate the effect of the anode inclination on gas covering and bath velocity, for both C02-cryolite and air-water system. Results obtained for the second system were compared to experimental data .

Jan 1, 2006

By S. Yue, P. Vo, M. Jahazi

The flow behaviour and microstructure development of a near-alpha titanium alloy during beta working has been investigated. Typical cogging conditions were simulated through compression testing of IMI834 at temperatures of 1025°C-1100°C, strain rates of 0.01 s-1 - 1 s-1 and post-deformation heat treatments up to 4h. Using a synthesis of available literature models, a finite element model has been developed and validated through quantitative measures of flow stress-strain data and beta grain characteristics. Flow behaviour was analyzed through a self-consistent method while the microstructure development was considered with regard to the kinetics of beta recrystallization. Deformation at beta or high alpha/beta working temperatures (T>l025°C) produced minor flow softening with complete grain refinement achieved through metadynamic recrystallization.

Jan 1, 2006

By A. F. Abd El-Rehim

The behavior of both transient and steady state creep of Al-4.5 wt% Cu and Al-4.5 wt% Cu-0.1 wt% In alloys was investigated using a constant stress where torsional oscillations of different frequencies and shear strain amplitudes were operated at various working temperatures. An augment in both transient and steady state creep rates was observed by increasing both frequency and shear strain amplitude of the applied oscillations. The mean values of the activation energy of both alloys for both creep stages were found to be equal to that quoted for dislocation intersection mechanism.

Jan 1, 2006

By P. Mengé

The covering of a hydraulically filled goethite pond is discussed from a geotechnical point of view. The characteristics of the goethite were defined in order to allow a detailed study of the procedure for the construction of the cover on top of the soft material and a verification of the stability of the cover and side slopes after construction. These characteristics and the main results of the studies are given, as well as the experiences and observations made during the execution of the work. Finally, the monitoring plan, during and after construction, is also discussed and some results are given. The 'Design and Construct' contract form was used to allow the contractor to choose the optimum and most economical method to realize the closing of the pond, based on his experience with similar projects. The works were carried out between mid 2003 and the end of 2004. The paper will, amongst others, discuss the special method of working that had to be developed to allow the covering of the whole pond in a relatively short time period, without soil improvement methods such as vertical drains or stabilization by in situ treatment. Fill material was used to establish a platform on top of the soft material so that the cover liner and finishing layer could be installed on top of the fill layer. The 'floating roof' principle was used; subsidences were allowed to occur during the installation of the impermeable top liner and soil cover.

Jan 1, 2006

By J. Marks

The measurement of greenhouse gas (GHG) emissions from primary aluminium production and inventory of these emissions of carbon dioxide and PF Cs have become an important issue for primary aluminium producers. Most global producers have either voluntary emission goals or emissions limits established through national regulatory requirements. International good practices for inventory of these emissions for national governments are established through the Intergovernmental Panel on Climate Change (IPCC). The current good practices, last updated in 2000, are being revised and are expected to be adopted by governments in the spring of 2006. There are a number of changes expected in the guidance that will impact how facilities account for their GHG emissions. This paper describes the changes to the guidance and the implications of these changes for aluminium producers.

Jan 1, 2006

By J. Dufour

Although the recovery of nitric and hydrofluoric acids from stainless steel pickle liquors has been solved by several methods, such as solvent extraction, acid retardation, evaporation or pyrohydrolysis, metals (mainly iron, chromium and nickel) are usually obtained as a waste or by-product that has to be disposed. Alternatively, the treatment requires a high liquor flow to be economical, as is the case for pyrohydrolysis. A new process has been developed for metals recovery, that produces metal oxides with a low fluoride content. This new technique is based on a selective precipitation mechanism, which produces nickel hydroxide with a purity of 90%, separate from a mixture of iron and chromium oxides and hydroxides suitable for recycling. The reaction mechanism is based on the precipitation of fluoride compounds of iron and chromium, K2FeF5 and CrF3. For this purpose, free fluoride must be added as potassium fluoride. Also, solid fluoride compounds are hydrolysed, releasing free fluoride. A part of the fluoride is recycled to the selective precipitation operation and the remainder is fed to the acid recovery stage. Nickel does not react in this operation; it remains in solution giving a high separation yield.

Jan 1, 2006

By N. Schreithofer

The deposition of octadecylamine (ODA) at the KCI crystal/NaCI-KCI brine interface was investigated using atomic force microscopy (AFM). The AFM images of freshly cleaved KCI specimens immersed in KCI-NaCI saturated brine at room temperature reveal disappearance with time of the atomic steps and formation of cubic NaC1 crystals. These crystals were found to form when the specimen was withdrawn from the saturated solution. Depending on the way of contacting the specimens with the octadecylamine dispersion, the AFM images show huge differences in the deposition patterns of ODA on KCI crystals. Adequate dispersion was found to help the formation of quite even ODA coverage. The coverage was several monolayers thicker when air/brine/solid contact took place, suggesting that in the potash flotation the collector is likely to be carried to the solid surfaces by air bubbles. The presence of methyl-isobutyl carbinol (M IBC) enhanced the dispersion of ODA in brine, thus helping the spreading of the surfactant on the KCI crystal surface.

Jan 1, 2006

By E. A. Roux

As the first mine-to-metal zinc operation utilising atmospheric leaching, solvent extraction and electrowinning, Skorpion Zinc faces unique challenges and opportunities. One of these challenges is found in the solvent extraction circuit, in which di-ethylhexyl phosphoric acid (D2EHPA) is used as the organic extractant. Although D2EHPA is an excellent extractant for zinc, it suffers from the co-extraction of ferric iron, which is produced during leaching and by the corrosion of the grinding media. This situation is partially mitigated by iron precipitation in the neutralisation step prior to solvent extraction. Unfortunately, some ferric iron still reports to the solvent extraction process. This leads to a slow build up of iron in the organic phase. Chemical stripping is used to maintain the Fe concentration at an acceptable level. In this paper, the efficiency of the iron removal process is discussed.

Jan 1, 2006

By I. Lackey

In 2004, Zinifex Budel Zink commenced testing with the objective to increase the precipitation of aluminium in the iron purification stage of its hydrometallurgical zinc circuit, without the use of expensive reagents. Findings from the literature applied to the leach circuit at Zinifex Budel Zink demonstrated that aluminium removal from the leach circuit could be increased by lowering the ferric concentration and acidity in the vessels where jarosite precipitation occurs. An associated increase in copper precipitation was mitigated by limiting the extent to which the ferric concentration was lowered in the vessels where jarosite forms and lowering the ratio of copper to aluminium in the solutions entering these vessels.

Jan 1, 2006

By D. M. Muir

The mineralogy of residues formed during the pressure acid leaching of arid region nickel laterite ore varies according to the salinity of the process water, alkali cation additives and the overall acid loading. In fresh water, hematite is the main iron-bearing leach residue component, together with amorphous silica and hydronium or sodium alunite/jarosite [(H3O,Na)(Fe,Al)3(SO4)2(OH)6]. As the process water salinity increases, or as NH4+ or K salts are added, alunite/jarosite is the kinetically favoured iron-bearing phase accompanied by an increase in acid consumption. The alunite/jarosite appears as two XRD distinct phases with different Fe:Al molar ratios. In weakly saline water, iron-rich alunite/jarosite slowly transforms to hematite and an aluminium-rich alunite/jarosite together with the release of acid. The addition of potassium salts forms a more stable alunite/jarosite whilst the addition of ammonium salts leads to greater transformation of alunite/jarosite at 250°C. Weakly saline process water gives enhanced nickel recoveries, whilst strongly saline process water gives lower nickel recoveries but higher soluble iron because of chloro-complexation. SEM and microprobe analysis shows very little nickel is associated with the alunite/jarosite and hematite phases. Nickel losses to the residues are attributed to adsorption on amorphous silica and to a lesser extent on alunite/jarosite.

Jan 1, 2006

By C. Taschereau, G. A. Vickell, A. R. Laplante

Evidence in support of an iron-gold corrosion cell during the high-temperature/highpressure elution of loaded carbon is presented herein including, but not limited to, its discovery, mode of genesis, and confirmatory laboratory testwork. A discussion of metallurgical and economic impacts, remedial investigations, plant design considerations, and future work including mitigative possibilities is presented.

Jan 1, 2006

By D. Markwart, B. Volk

Anode effects are a phenomenon of the aluminium electrolysis process which produce potent greenhouse gases called PFCs (CF4, C2F6). With concerns surrounding global warming, and increasing regulation of GHG emissions, anode effects have become a significant sustainability issue for aluminium producers. In modem smelters, sophisticated computer control and automated alumina feeding systems allow for very tight control of the alumina concentration in the electrolyte and thus very low anode effect frequencies. Older smelters, however, do not have these systems and must either invest heavily to obtain them, or find other, innovative ways to reduce anode effect frequency. This paper will present the integrated approach to anode effect reduction used in the Vertical Stud Soderberg (VSS) potlines at Kitimat Works. Through an innovative combination of simplified signal analysis, modified alumina feed control logic, anode effect prediction, and anode effect prevention using a pager based communication system, Kitimat W arks has been able to make significant reductions to its anode effect frequency.

Jan 1, 2006

By C. Liu

Zeta potentials and settling rates of an oil sands tailings sample taken from Syncrude Canada Ltd's Aurora Stacker Pilot Operation were studied. Two clay minerals, kaolinite and illite, were also studied since these are the major constituent minerals in the fine oil sands tailings. Process water, decanted water as well as distilled water were used. It was observed that the zeta potentials of the tailings solids showed maximum negative values in process water at pH 8-10, which coincides with the pH of commercial hot water bitumen extraction process. The settling rates of the tailings sample were very low, at 0.008 m/hr in decanted water and 0.04 m/hr in process water. The rates were increased to 1.0 m/hr in decanted water and 0.13 m/hr in process water at an addition of 50 g/t Ciba AF1235. Although the settling rate was higher the supernatant was cloudier in decanted water than in process water. Further increase in the dosages of Ciba AF1235 did not increase the settling rates in decanted water but gradually increased it in process water, reaching 0.46 m/hr at 100 g/t. The results indicated that lower concentrations of Ca2+ and Mg2 (in decanted water) benefited settling rates but did not benefit supernatant clarity. Test results also indicated that Ciba AF1235 caused selective flocculation of the tailings sample, since the top sediments had higher illite and lower quartz contents than the bottom sediments.

Jan 1, 2006

By A. Zarei-Hanzaki, S. M. Fatemi-Varzaneh, M. Haghshenas

The microstructure in modified semi-solid ALTHIX (A356) alloy consists of aAl phase with Al/Si eutectic structure. Silicon phase in eutectic structure is coral like with fine fibers. The lack of good ductility in this alloy is related to the presence of silicon fibers. Accordingly many investigations have been recently conducted to modify the Si morphology through Thermomechanical processing on this alloy. In the present work an ALTHIX (A356) alloy was deformed at 450°C, 500°C and 540°C through different strain rates. Consequently the silicon fibers were broken into small particles. The results indicated that the Si particles may coarsen according to Ostwald ripening mechanism at 540°C deformed by rate of0.0005 sec-1 & 0.0001 sec-1-

Jan 1, 2006

By S. B. Kang

Magnesium has poor ductility at temperatures lower than 225°C and, as a result, Mg alloy sheets are produced via fairly complex thermomechanical processes consisting of numerous sequential steps of hot (warm) rolling with low reduction and intermediate recrystallization annealing operations. In context of the present study, a simple technology for the fabrication of magnesium sheets by hot (warm) rolling was applied to various magnesium alloys. The misch metal addition in those AZ alloys was done to evaluate the deformation behavior. Tensile tests were carried out for those AZ alloys after applying different heat treatments. The precipitation of ß phase (Mg17Al12 phase) induced different microstructures with various cooling method from solution treatment temperature, and also with various annealing treatment temperatures.

Jan 1, 2006