Search Documents

By J. D. Clucas, D. B. Dreisinger

"The Starved Acid Leach Technology (SALT) has been developed by Search Minerals to extract nickel and cobalt VALUES (from nickel laterite ores (saprolites) and Caron plant residues. The technology consists of sulfuric acid atmospheric leaching of the ores or residues followed by neutralization and recovery of nickel and cobalt. The acid addition is carefully controlled to maximize nickel and cobalt extraction while minimizing overall consumption of acid by various gangue reactions. The final recovery processes can be tailored for maximum economic benefit. The use of resin-in-pulp processing is advocated as the most cost effective method for initial recovery of nickel and cobalt from lower grade materials. INTRODUCTIONCommercial processes for laterite ore treatment vary according to laterite type and local conditions. The two general categories of laterite ore are saprolites and limonites.Saprolites are generally treated by pyrometallurgical processes for reduction of nickel to matte or ferro nickel alloys. The high cost of drying, chemical reduction and electric furnace smelting requires that the saprolite grade for economic processing is of the order of 1.8% nickel or higher. There are of course large amounts of saprolite that fall below this “cut-off” grade that are not currently economic.Limonites can be treated by the Caron Process which involves drying of the ore, a reduction roast of the whole ore to reduce nickel and cobalt (and some iron) to the metallic state followed by ammonium – ammonium carbonate solution to leach nickel and cobalt. Nickel and cobalt recovery are low (70-85% for Ni and 20-50% for Co). The Caron plant tailings therefore contain high levels of unrecovered nickel and cobalt. Relatively few plants have used the Caron Process and new installations are not anticipated due to the high energy cost of drying and reduction roasting. Nevertheless, plants in Brazil (Niquelandia), Australia (Yabulu) and Cuba continue to operate.The high pressure acid leach (HPAL) process was pioneered at Moa Bay in Cuba in the 1960’s in the treatment of limonites. In the 1990’s the HPAL process was touted to revolutionize the nickel industry with low capital and operating costs for new installations. Murrin Murrin, Cawse and Bulong in Australia were started and in each case the technical difficulties of operating at extreme temperature and pressure conditions and the challenges in “ramping up” a complex hydrometallurgical facility conspired to cause these plants to fail economically. At present, Cawse and Bulong are closed and Murrin Murrin continues to operate after undergoing a financial restructuring."

Jan 1, 2012

By R. Khanna, K. Hyun Ko, A. J. Berkovich, J. Hook

"The co-pyrolysis of synthetic polymer polyethylene terephthalate (PET) and agricultural wastes (naturally occurring polymer-macadamia nut shell) was investigated in the temperature range 473K to 1273K using a horizontal furnace with an aim to understand their thermal degradation under isothermal conditions. In-depth characterization of pyrolysis residues was carried out using x-ray diffraction (XRD) and solid state nuclear magnetic resonance (NMR) for carbon structure, and through determination of the concentration of unpaired electrons using electron paramagnetic resonance (EPR). In previous studies, it has been found that PET thermally decomposes ~ 650K-700K, releasing (~80 wt % of initial weight) gaseous products due to random chain scission. In the case of macadamia nut shell, three types of byproduct can be obtained from pyrolysis: char, tar and gaseous products. In the co-pyrolysis of macadamia nut shell with PET in 50-50 wt% ratio, total product weight ratio could be modified with the addition of PET acting as a hydrogen source. This is because a recombination of thermal cracking products of cellulose could be suppressed by hydrogen from PET, which will later lead to an enhancement of tar formation. In addition, pyrolysis around 673K is sufficient for bond cleavage to occur in cellulose and lignin leading to the formation of negatively charged activated carbon with high surface area, providing bonding sites for volatiles evolving from PET. Therefore the co-pyrolysis may be able to enhance the product yield (tar/char/solid carbon residue) along with a reduction in the release of gaseous products. During the co-pyrolysis, temperature was found to have a significant influence on the kinetics of thermal degradation and solid residual by-products after co-pyrolysis.INTRODUCTIONPlastics are being used worldwide in a wide range of applications in the modern society; their usage has resulted in increasingly a massive waste problem. The production of most synthetic plastics requires hydrocarbons that are produced from petrochemicals derived from fossil oil and natural gas, a non-renewable source (Speight 2011). Currently, plastic manufacture utilizes ~4% of world oil and gas production, and it is expected to drive further increases in petroleum demand by 1-2% due to their large volume of manufacture (Hopewell, Dvorak et al. 2009). Landfilling and incineration of plastic waste are the two main routes to plastic waste management (Encinar and González 2008). In Australia, only 10% of waste plastics were recycled in 2006 (White and Hyde 2011). This means that large amount of fossil fuels from plastics has either been simply burned for energy recovery or buried in the ground. There is an urgent need for developing alternative avenues for recycling waste plastics. Our group at UNSW has carried out extensive research on the recycling of waste polymers as carbon resource in steelmaking including slag foaming and carbon dissolution from waste plastics into liquid steel at 1600°C; the effect of basic plastic characteristics such as chemical composition, structure, bonding network etc. was examined (Sahajwalla, Rahman et al. 2009)"

Jan 1, 2012

By Dayang Datu Khalil, Charle Amoah, Fred Kock

Abosso Goldfields Limited has been optimizing the comminution circuit at the Damang Mine Operation for the treatment of 100% primary ore. The optimization process started at a base rate of 343 tph when treating primary crushed primary ore, and was increased to above 600 tph with partially crushed primary ore. Abosso Goldfields engaged Orway Mineral Consultants (OMC) to assist with the optimization process in 2009 and the two companies have been working together since, to further refine the process. Continuous improvement was achieved through crushing circuit modifications, changes in operating processes and grinding control system utilization. This paper discusses the improvements developed for the increase in milling capacity and improvements in final product size.

Jan 1, 2012

By Cosmin Carpinisan, Erich J. Hofmann, Stephen J. Hall

"Since presenting a technical paper regarding their unique capabilities in Forged Steel Mill Gearing at the SAG-2006 Conference, Australian heavy engineering company Hofmann Engineering has pioneered a number of new manufacturing processes and design concepts for components of large comminution equipment. These include: 1. Novel design improvements for HPGR Rolls with forged steel tyres and a unique patented tungsten carbide insert designed to improve wear life, enhance autogenous layer build-up, and to reduce breakage & chipping under load. 2. Development of forged fabricated Mill Heads using rolled & welded high-tensile steel plate as alternatives to cast conical mill heads. 3. Insitu Girth Gear measurements for profile and wear via portable 6-axis CMM. 4. Gear and Pinion designs to AGMA-6114 for SAG mills of 38’-40’ diameter to 24MW and for Ball Mills of 26’ diameter to 18MW. The paper presents case studies from the Australian heavy manufacturing facilities of Hofmann Engineering, combined with news of their new gear manufacturing and gearbox overhaul facility in Canada."

Jan 1, 2012

By G. Fuentes, J. Viñals

"The nature and basic kinetics of the hydrothermal reactions of bornite, covellite pyrite and enargite with copper sulfate solutions were investigated, as a previous study on the behavior of the bulk Chilean copper concentrates. The reaction of bornite produced digenite at 160 °C and djurleite above this temperature. Covellite was transformed to digenite at < 200 °C and to chalcocite (Q and M) at > 200 °C. The pyrite reaction was significant at > 200 °C and extensive at 240 °C, enargite reacts only above 240°C and produces digenite. The hydrothermal treatment of Chilean Codelco-type copper concentrates with hydrothermal reactions was similar to those obtained from pure mineral samples.INTRODUCTIONStudies on the hydrothermal enrichment of chalcopyrite concentrates were begun by MacGauley and Roberts (1951), Roberts et al. (1953) and MacGauley and Schaufelberger (1956). In the 1970's these processes were reexamined by McKay et al. (1972), and Johnson and Coltrinari (1976), but it not was until the 1990s when the kinetics, mechanisms and full engineering aspects were studied by Barlett, (1992), Jang and Wadsworth, (1994) and Peterson and Wadsworth (1994). The main objectives were to solve some important problems in the copper pyrometallurgy: The increase of the smelting capacity, the reduction of the iron slag – and associated copper losses – as well as the reduction of sulfur emissions. The present rise in copper demand and price implies the production and subsequent treatment of very impure concentrates. Thus, a significant increase of environmental problems can be expected in the copper pyrometallurgy. The previous purification of concentrates can reduce the processing of wastes containing hazardous heavy metals in the copper refineries and the hydrothermal treatment can be an alternative which combines both enrichment and purification. On the other hand, Chuquicamatatype concentrates (Viñals et al., 2004a) contains digenite (Cu1.8S), pyrite (FeS2), chalcopyrite(CuFeS2), b ornite (Cu5FeS4), covellite (CuS) and sphalerite (ZnS) as the main mineral components, with minor amounts of enargite (Cu3AsS4), galena (PbS) and molybdenite (MoS2)."

Jan 1, 2012

By Tom Shumka

All mineral processing facilities that use girth gear driven mills need to inspect the gear teeth on a routine basis, whether it is every six months or every three years. The inspection frequency depends upon gear tooth condition, and the objective is to ensure operational integrity of the gear teeth. Conventional methods such as magnetic particle testing, visual inspection, or dye penetrant examinations rely heavily on interpretation. At best, these techniques can determine whether a defect exists, but are unable to provide information on defect severity. This paper describes the use of combined Eddy Current Array (ECA) and Alternating Current Field Measurement (ACFM) to provide a complete survey of all surface breaking indications on the whole gear tooth depth. This method accurately determines the size, length and depth of any cracks found on the surface.

Jan 1, 2012

By F. Habashi

"While bioleaching of pyrite concentrates has been successfully used in industry to liberate gold from the sulphide matrix for subsequent cyanidation, the same technology cannot be recommended for leaching chalcopyrite concentrates for copper recovery. It will be shown to be uneconomical and cannot compete with pressure leaching technology. Data on the pilot plants that were constructed for this purpose and were shut down will be given.INTRODUCTIONBacterial leaching has been successfully applied for heap leaching of low-grade copper ores (Habashi, 1978, 1999). One of the major operations is that at Bingham in Utah (Figure 1). The leach solution collected at the bottom of the heap is extracted by organic solvents and the strip solution is electrolyzed to get high purity copper. The process was extended to treat auriferous pyrite concentrates to liberate gold and render it amenable to cyanidation by a process known as BIOX (Marsden & House, 2006; Lunt & Briggs, 2005).BIOX plants currently or recently in operation are the following:??Ashanti Goldfields Company, Ghana. Designed with an initial capacity of treating 720 tonnes of concentrate per day, the Sansu plant has since been expanded and currently has four modules processing 960 tonnes per day in all. It is by far the largest biooxidation plant in the world. The capital cost of the plant totalled US $25 million (1994 terms) and the operating cost is currently US $17/tonne milled.??Fairview, South Africa. The plant at the Fairview mine in Barberton, which was the initial pilot plant, has been fully operational since 1986. It was originally designed to treat 10 tonnes/day of concentrate but with the success of the project this has been increased to 55 tonnes per day. With the purchase of Fairview by Avgold’s Eastern Transvaal Consolidated, Avgold concluded a licensing agreement with Gold Fields, formerly known as Gencor, entitling it to use the BIOX technology to treat itsconcentrate.??Saõ Bento, Brazil. A BIOX plant was recently in operation in Brazil at the Saõ Bento Mine where a pressure oxidation circuit is used to treat the refractory flotation concentrate. This plant has confirmed the viability of combining bio-oxidation with pressure oxidation as a cost-effective method ofincreasing capacity at an existing oxidation plant.??Wiluna, Australia. The plant at Wiluna Gold Mine, Western Australia, was commissioned in 1993. Although originally designed to treat 115 tonnes per day of concentrate this has subsequently been increased to 158.??Other plants at Tamboraque in Peru, Harbour Lights and at Youanami in Australia have been commissioned recently."

Jan 1, 2012

By J. Dong

"A “green” collector project has been initiated at Vale Base Metals Technology Development to replace xanthate. Bench and miniplant testwork showed comparable metallurgical results between xanthate and DTC (sodium dibutyl dithiocarbamate), a “greener” collector. During the first DTC plant trial, a strong interaction between the process water and DTC negatively impacted the metallurgy. The subsequent investigation showed that the quality of process water including suspended solids and dissolved metal ions had a significant impact on the performance with DTC, while less so with PAX. This paper explains these differences using UV spectrophotometry and batch flotation tests. INTRODUCTIONVale Base Metals is dedicated to sustainable mining and mineral processing. One of the key activities is to find a “greener” collector to replace xanthate (PAX: potassium amyl xanthate), which decomposes during storage and flotation causing CS2 emissions in the work place. As the most promising candidate, DTC (sodium dibutyl dithiocarbamate) was evaluated in the lab and miniplant (Dong & Xu, 2011). Consequently, a plant trial was conducted in the winter of 2010. However, the results were not as good as expected. The subsequent investigation showed that the quality of process water played a significant role in the metallurgical performance with DTC but less so with xanthate.From test work in 1996 and 1997, a series of batch tests were performed at Clarabelle Mill to investigate the winter/summer metallurgical shift with xanthate. As shown in Figure 1, the winter metallurgy was considerably worse than the summer metallurgy (Xu & Wilson, 2000). At 80% pentlandite recovery, the concentrate (Cu+Ni) grade was 21% in the winter and 26% in the summer. At 23% (Cu+Ni) concentrate grade, pentlandite recovery was 85% in the summer and 70% in the winter. In the summer, the process water is much cleaner, with very low concentrations of dissolved metals ions and suspended solids; while in the winter, the water is yellow and cloudy, with much higher suspended solids. Based on these results, it was concluded that the process water in winter has a detrimental impact on metallurgy."

Jan 1, 2012

By D. W. Bennett, J. B. Hadaway

The operation at Phu Kham commenced design and construction in early 2006 and was commissioned in May 2008. This paper will examine and discuss the project from the inception of flow sheet development and equipment selection, equipment design and manufacture, construction, commissioning and ramp up to full production. The paper will touch on the strategies employed to achieve a short schedule and the efficient use of capital, but with the main emphasis on the grinding circuit. Various challenges during the early years of operation will be discussed including the effect of ore characteristics, including competency, on the performance of the grinding circuit. Actions to overcome these challenges and to enhance performance will also be discussed. Finally, current and future plans to improve the performance of the grinding circuit and the overall plant will be summarised.

Jan 1, 2012

By Chao Yang, Liguo Tian, Yan Yang

"The Jinfeng gold mine is one of the three gold mines that Eldorado Gold has in China and it is the second largest gold mine in China. The mine is located in a relatively remote and mountainous area in the southwestern Guizhou province. The orebody is similar to the Carlin type deposit in Nevada. The mill throughput was designed to treat 3,600 tones per day. The ore comes from open pit mining and underground mining, and is fed to one-stage jaw crushing. The crushed ore is stockpiled, reclaimed and then fed to the SABC grinding circuit. After classification with hydrocylones, the ore is floated, and the resultant concentrate is oxidized biologically in a process known as BIOX®. The oxidized concentrate is then washed in a CCD circuit and finally leached with cyanide in a CIL circuit for gold extraction. Jinfeng produces about 180,000 oz of gold per year.This paper introduces operations and modifications of SABC circuit over the past three years, and then describes some technical characteristic of the SAG mill and other circuits in the processing plant.Major modifications and improvements on the SABC circuit are described in the paper, including:1. Impacts of grinding ball and mill liner with respect to material selection, quality, hardness, manufacturing methods, and interactions between mill liner and grinding ball.2. Effect of milling operation parameters on milling efficiency.3. Impacts of SAG mill scats and modifications of grate size to improve mill throughput.4. Design and construction of a pebble crushing system, and recycle the crushed scats to the SAG mill to improve mill throughput.With the above-mentioned modifications, 20% increase over the design in mill throughput has been realized over the past three years, and operating cost has been significantly reduced. However, some issues still remain, and thus process modifications and technical innovations are still needed."

Jan 1, 2012

By N. Plint, D. Philips, J. Sweet, B. Durant

A pilot scale AG milling campaign was conducted at the AngloAmerican Platinum pilot plant in South Africa. Different blends of hard: soft (silicate: chromite) and coarse: fine particles in the AG mill fresh feed were tested. The effects of multi-component feed on the pilot scale autogenous grinding are presented in this paper, and can be used as a guideline for multi-component feed blends for AG mil

Jan 1, 2012

By G. Belzil, F. Robichaud, M. Fullam

"The Goldex mining and milling complex is operated by Agnico-Eagle Mines Ltd. and is located in the Abitibi greenstone belt of Northwest Quebec, Canada. The mill operates presently at a throughput of 8,250 tpd with gold grade varying between 1.8 and 2.2 g/t. The ore is very high in gravity recoverable gold (GRG) at about 92% and as such a significant emphasis was placed on the gravity circuit. Commercial production started in 2008. Average gold recovery is 93.5% with about 68% of gold recovery coming from the gravity circuit. Over the course of the first several years of production, several gravity audits were carried out. In 2009, a complete gravity audit was completed, including ore, classification, Knelson Concentrators, and the gold room. In 2011, an audit was undertaken of the flotation circuit to determine the efficiency by which GRG is floated. Large samples of flotation feed and tails were collected and process for GRG content. This allowed a link between gravity and overall recovery to be made. This paper presents results of the audits and the development of a model linking gravity and overall gold"

Jan 1, 2012

By M. Härting, D. T. Britton, M. Nzikou Mamboukou

"Copper containing different types of nanocomposites have been characterized for nanolabelling and ID. Three types of the rare earth nanoparticles were used for this study, the oxide and the sulphur compound of the Eu and Tb. Characterization techniques uses SEM, and Raman for morphology, chemical composition, and optical characterization respectively. It has been shown that it is possible to include the rare earth particle in a copper matrix without damaging its physical properties. INTRODUCTIONThe development of new materials, often involves the addition of new properties without changing the beneficial properties of the original material (Chen et al., 2009; Khana et al., 2007; Patil et al., 2008). Nanocomposites are nanostructured materials, whose structural elements including clusters, crystallites or molecules, of dimensions ranging between 1 to 100 nm (Moriarty, 2001), or a composite material where one of the phases is a one, two or three dimensionally nanostructured material (Nanotechnology, 2006; Wang, 2001). Nanocomposite materials research is a fast growing area due to the high demand for materials for specialized applications (Edelstein & Cammarata, 1998), such as biolabelling, magnetic storage media, solar energy transformation (Jisen et al., 2004), and resistance welding applications (Bessergenev et al., 1997; Kwon et al.,2006).The properties of the nanocomposite materials depend not only on the properties of their individual parent materials, but also on their morphology and the interfacial characteristics. Thus, significant efforts have been focused on the control of the nanoscale structures via innovative synthesis approaches. Therefore, novel materials of unique properties may be obtained by combining properties from the parent constituents into a single material (Balan, 2006; Garcia et al., 2009). Possible effects of nanocomposites in the original material may include changes in the mechanical properties such as hardness , wear resistance (Rafaja et al., 1987), and electrical properties (Britton et al., 2003). The inclusion process may therefore be used to tailor materials to have particular mechanical, electrical and optical properties (Das et al., 2009). However, to fully understand the nanocomposite, it is necessary to study the fundamental properties of both the host matrix and the inclusions (Li, 2008)."

Jan 1, 2012

By J. Drozdiak

In this paper we present the results of preliminary investigations into the applicability of new laboratory scale tests for the prediction of operating gap and specific throughput in high pressure grinding rolls (HPGR). The work is a part of the CAMIRO HPGR research program being conducted at the University of British Columbia, which aims to develop a suite of small-scale tests and procedures for the selection and sizing of HPGRs. A focus of the presented study is to test sample types in terms of their terra-mechanics based characteristics and relate them to specific throughput and gap results from pilot HPGR testing on the same samples.

Jan 1, 2012

By S. Esfahani, M. Barati, Y. Kauwachi

"Heat recovery from slag has gained attention due to its high potential in lowering energy intensity of metal extraction processes. A direct method to recover the thermal energy of slag is to use countercurrent air flow that extracts the heat from falling droplets. Often, the solidified slag is aimed to be used as a substitute for Portland cement, thus high cooling rates are required to form an amorphous slag with sufficiently strong hydaulicity. Rapid cooling however involves using large gas flow rates that in turn lower the thermal efficiency of the process. This article presents a mathematical model that was developed to determine the optimum conditions in the heat recovery process and to investigate the effect of the air flow and granule diameter on the cooling rate of the droplets as well as the thermal efficiency of the heat recovery system. INTRODUCTIONMetallurgical slags are the largest by-product of high temperature materials refining and extraction processes. The total amount of metallurgical slag produced in the year 2008 has been estimated at up to 422 million tonnes containing up to 222 TWh/y (Barati and Esfahani, 2011) of thermal energy. Over the past four decades attempts have been made to recover this substantial amount of energy as heat, electricity, or fuel, while none of the proposed method has been commercialized yet.During slow cooling the slag tends to crystallize the constituents (CaO, SiO2, Al2O3, etc.) into a hard, heavy solid. In the past, over 90% (Bengt, 1983) of the molten waste was discharged onto heaps and allowed to cool slowly, then crushed and used in road construction or land filling or as coarse aggregate for concrete. However, later it was found if cooled rapidly, the slag can be used as a substitute for Portland cement. As a result, processes such as wet granulation were created in which molten slag is fragmented with water, forming amorphous (glassy) phases. Despite its effectiveness in producing a suitable material, heat would not be recovered through this process. Thus, dry granulation was introduced in 1930’s and was developed further in 1970 – 1980’s."

Jan 1, 2012

By K. Sawamukai, S. Ogasawara, D. Umenai, T. Tsuruta

"Removal of cobalt, strontium or cesium ion from the aqueous solution containing each metal ion only using microorganism was examined. Arthrobacter nicotianae which had a high ability to remove cationic metal ion was used for the removal of each metal. The removal of cobalt, strontium or cesium using A. nicotianae cells was affected by the solution pH, concentration of metal ion, and cell amount. The effects of above mentioned factors on the removal of each metal and time course of strontium from the solution containing each metal only using A. nicotianae cells were reported in this paper. INTRODUCTIONRadioactive elements, such as cesium, iodine, strontium, plutonium, barium, cobalt, lanthanum, yttrium, and tellurium, were detected around Fukushima Daiichi nuclear power plant, which was damaged by the magnitude 9.0 earthquake and the tsunami followed.The removal of radioactive elements from contaminated sources is a worthwhile subject to investigatein terms of environmental control. Research efforts have been especially concentrated on studying microorganisms that remove uranium including bacteria (Andres et al, 1993, Hu et al, 1996, Marques et al, 1991, Strandberg et al, 1981), actinomycetes (Byerley et al, 1987, Friiss and Myers-Keith, 1986, Golab et al, 1991), fungi (Byerley et al, 1987, Galun et al, 1983a, Galun et al, 1983b,Tsezos and Volesky, 1981, White and Gadds, 1990) and yeasts (Strandberg et al, 1981, Schmate II et al, 1978).We have investigated removal and recovery of uranium from aqueous systems using microorganisms isolated from uranium mines. We identified some strains of bacteria with extremely high uranium removing abilities (Sakaguchi et al, 1996), and thus, the microbial biomass may be considered as an adsorbing agent for the removal and recovery of uranium and heavy metals present in aqueous systems around Fukushima Daiichi nuclear power plant.In the present study, we screened various species and strains of bacteria, actinomycetes, fungi, and yeasts for their ability to adsorb uranium (Tsuruta, 2002). Basic features affecting uranium adsorption?co-existing cations and anions, cell amounts, pH, and the adsorption time course?by Arthrobacter nicotianae cells, which adsorbed the largest amount of uranium, were also investigated. In addition, we examined the removal of an other actinoid element, thorium ion, which may be present with uranium in refining effluents.In this paper, the removal of cobalt, strontium, or cesium from the solution containing each metal ion using A. nicotianae cells is discussed."

Jan 1, 2012

By M. Maeda, H. Sasaki

"Precious metals such as platinum, palladium, and rhodium are commonly used for automotive catalyst converters. To recover these metals with lower environmental load and cost, exposure to zinc vapor was proposed as a pretreatment prior to acid leaching. Alloying with zinc is expected to enhance dissolution of precious metals and reduce the amount of toxic chemical agents required for the leaching. This study examined the effect of the alloying pretreatment using model catalysts. Catalysts were immersed in leaching solutions for a predefined time with or without zinc vapor pretreatment, and the amount of dissolved metals was then evaluated. INTRODUCTIONAutomotive catalysts account for large portions of the world consumption of platinum (Pt), palladium (Pd), and rhodium (Rh) (Butler, J., 2011). Because of their limited production and high prices, recovery of the precious metals from spent catalysts is obviously an important issue. A representative structure of an automotive catalytic converter can be described as a monolithic ceramic support with a honeycomb structure which is coated with porous oxides such as those of aluminum (Al2O3), cerium (CeO2), and zirconium (ZrO2) (Heck & Farrauto, 2001; Matsumoto & Shinjoh, 2007). Small particles of precious metals, originally several nanometers or less, adhere to the oxides.Typical recovery processes for precious metals from scraps are shown in Figure 1 (a)-(c) (Habashi, 1997; Yoo, 1998; Shibata & Okuda, 2002). Precious metals can be recovered by using non-ferrous smelters as Figure 1 (a) shows. Smelted along with metals such as copper (Cu), precious metals and ceramics in the scraps are absorbed into the metal phase and slag phase, respectively. Because the metals separate from Cu as anode slime in successive electro-refining, such a process can recover precious metals as co-products of Cu. However, in order to prevent negative effects on the principal process, a specialized procedure is needed. Figure 1 (b) is a specialized approach in which scraps are melted at elevated temperature with Cu called the Rose process. Here Cu works as a collector metal, and the absorbed precious metals are then concentrated by oxidation of Cu. Such a process can separate precious metals from ceramics constituting catalyst converters. Smelting at high temperature, however, requires extensive equipment as well as a high amount of energy. On the other hand, hydrometallurgical processes may be effective to separate precious metals from ceramics into an aqueous solution, because chemical agents can act on these metals selectively (Figure 1 (c)). Leaching of precious metals, however, requires strong acid and oxidizing agents because of their corrosion resistance; this makes liquid waste disposal and the large environmental load controversial. To solve the problem, a metal vapor pretreatment was proposed (Okabe, Yamamoto, Kayanuma, & Maeda, 2003a, 2003b; Kayanuma, Okabe, Mitsuda, & Maeda., 2004; Kayanuma, Okabe, & Maeda, 2004; Itoh, Kayanuma, Miyake, Kimura, & Maeda, 2005). A flow diagram of the process using zinc (Zn) vapor is shown by Fig. 1(d). Exposed to Zn vapor, precious metals are expected to form alloys which dissolve more easily than pure precious metals, thus reducing the use of chemical agents and environmental load involved with successive leaching. In previous research (Sasaki, Miyaki, & Maeda, 2010; Sasaki & Maeda, 2010, 2012), dissolutions of precious metal alloys formed by Zn vapor treatment were examined in hydrochloric acid (HCl) using an electrochemical method, and it was confirmed that these metals dissolved at higher rates from the alloys than from their pure states (Figure 2). In this study, the availability of the alloying pretreatment was demonstrated by testing on model catalysts in leaching solutions."

Jan 1, 2012

By A. L. Hinde, H. Dong, J. T. Kalala

"The High Pressure Grinding Roll (HPGR) is gaining acceptance in the mineral processing industry and has become a competitive technology in reducing the specific energy consumption in Mineral processing plants. The amount of samples required for HPGR amenability testwork and HPGR wear tests is usually high and often cannot be available at early stage of projects were only a few drill cores are available.Although HPGR was initiated from small scale piston die compression tests, the development of small scale piston die test to predict the performance of HPGR has been slow.The objectives of this paper was to present the designs, operating procedure of piston-die press and operating conditions which have resulted in similar particle size distribution obtained from a piston die test and HPGR Labwal unit starting from the same feed size distribution. Testwork were conducted using a 2 MN piston-die press and a Labwal HPGR unit on major South African ore types, viz, gold, platinum and iron ores. The results obtained show that piston-die test can generate data to predict energy consumption, product size distribution, and even to evaluate the edge effect."

Jan 1, 2012

By K. S. Raja, B. Pesic, S. Kshetri

"We investigated the electrochemical corrosion behavior of commercial permanent magnetic material (NdFeB alloy) in 0.1 M NaH2PO4 solution (pH:4.75) containing 0 – 1000 ppm of chloride at room temperature (298 K). The material was evaluated in magnetized and demagnetized condition with different surface preparations such as: Ni-Cu-Ni coated, uncoated (bare), and anodized (in fluoride containing ethylene glycol at 60 V for 15 minutes to form a thick nanoporous oxide surface). The nickel coated magnetic sample showed reasonable pitting corrosion resistance up to 100 ppm chloride addition. The uncoated samples showed passivity in chloride free phosphate solution. Chloride additions caused pitting and the pitting protection potential was equal to the corrosion potential with 100 ppm chloride addition. Demagnetization did not alter the electrochemical polarization. However, the passive film formed on the magnetic sample showed higher charge carrier density than the film formed on the demagnetized sample. INTRODUCTIONSintered NdFeB permanent magnets exhibit excellent magnetic properties such as large energy product [(BH)max > 450 kJ/m3], high saturation magnetization (1.6 Tesla), and high coercivity (1.2 – 2.08 x 106 A/m) (Sugimoto, 2011). However, the NdFeB magnets are prone to corrosion attack because of the presence of Nd-rich intermetallic phases, such as Nd4Fe (Jurczyk & Jakubowicz, 2000). Nd-rich and B-rich intermetallic phases are distributed in a matrix of Nd2Fe14B tetragonal ferromagnetic compound in a permanent magnet. Generally, several types of Nd-rich phases are present in the magnet with Fe:Nd ratios ranging from 1:1.2 to 1:7. The volume fractions of Nd-rich and B-rich (Nd1+xFe4B4 type) phases are about 10% and 7% respectively (Li, Ma, Li, & Wang, 2011) . Among these intermetallic phases, Nd-rich phase has the most active electrochemical potential. Therefore, dissolution of this phase occurs in preference to other phases by galvanic corrosion when exposed to moisture. Since Nd-rich phases are present at the grain boundaries of the Nd2Fe14B matrix, corrosion leads to disintegration of the magnet."

Jan 1, 2012

By Tom Shumka

All mineral processing facilities that use girth gear driven mills need to inspect the gear teeth on a routine basis, whether it is every six months or every three years. The inspection frequency depends upon gear tooth condition, and the objective is to ensure operational integrity of the gear teeth. Conventional methods such as magnetic particle testing, visual inspection, or dye penetrant examinations rely heavily on interpretation. At best, these techniques can determine whether a defect exists, but are unable to provide information on defect severity. This paper describes the use of combined Eddy Current Array (ECA) and Alternating Current Field Measurement (ACFM) to provide a complete survey of all surface breaking indications on the whole gear tooth depth. This method accurately determines the size, length and depth of any cracks found on the surface.

Jan 1, 2012