Search Documents

By B. K. Mishra, P. Patnaik, B. C. Tripathy, I. N. Bhattacharya

Cobalt is an essential metal considering its numerous industrial applications. The demand for the metal is increasing due to its wide range of use in, for example, rechargeable batteries and as an alloying element in super alloys. Cost effective production of Co is critical. Electrowinning from aqueous sulphate solutions is the preferred technology available for the production of Co. Attempts are being made to produce uniform, smooth and bright deposits of cobalt metal. Use of organic additives in the electrolytic bath improves current efficiency and deposit morphology of the metal. We investigated the effect of quaternary amines TEABr, TPABr and TBABr during cobalt electrowinning from aqueous sulphate solutions. Among the additives studied, TEABr yielded the best results. Smooth and bright deposits of cobalt were obtained at low concentration of TEABr (10 mg/L) maintaining a very high current efficiency of 99.6%. X-ray crystallography indicated that (100) is the most preferred plane of crystal growth.

Jan 1, 2014

By R. F. Robertson

"Adsorption isotherms of hexyl mercaptan vapour on synthetic sphalerite, zinc sulphide and zinc oxide were de-termined with a gravimetric McBain-Baker micro balance incorporated in the B.E.T. apparatus. Isotherms are given for hexyl mercaptan on synthetic sphalerite at 25°C, 0.5°C and 50°C; on zinc sulphide at 25°C and 1.5°C; and on zinc oxide at 25°C. All these isotherms are sigmoidal, with a definite change in slope at or close to the mono-layer. The amount of mercaptan adsorbed below the monolayer increases almost linearly with relative pressure to P/P0 = 0.8.Above this value, the amount adsorbed increases very rapidly with relative pressure. Hysteresis loops appear in the isotherms for all adsorption-desorption cycles. These loops are completely reversible. It is not possible to desorb the mercaptan monolayer from any of the adsorbents, even at elevated temperatures."

Jan 1, 1966

By P. R. Goad

"Kidd Creek is a large volcanogenic base metal sulphide deposit, located near the west end of the Abitibi greenstone belt, 27 km north of Timmins, Ontario. The rhyolite geology is characterized by a NNE-striking and steeply east-dipping package of rhyolite volcaniclastics upon which has been imposed a strong ESE-striking and north-dipping structural fabric . Massive rhyolite units with grey-black. chloritic cores and yellow, sericitic margins intrude as dykes into the stratigraphic footwall and as sills higher in the stratigraphy. Massive rhyolite units positioned near the top of the felsic pile exhibit an extensive marginal development of hydraulic fracturing and are termed crackle-brecciated rhyolite.The stringer sulphide zone is positioned in a lobate blanket of crackle-brecciated rhyolite at the top of the felsic pile. The stringer sulphide zone is characterized by a mature chemical alteration, being specifically depleted in alkalis and enriched in iron-rich chlorite. with accompanying silica, sericite and carbonate alteration. A suite of trace elements characterizes this mature alteration. The massive rhyolite units, which intrude lower in the rhyolite volcaniclastics, exhibit a core of weak chlorite alteration and strong marginal sericite alteration. Tight or unfractured massive rhyolite units are essentially devoid of sulphide mineralization and exhibit a suite of trace elements characteristic of this immature alteration. It is interpreted that the massive rhyolite units intruded into an already evolving system and ""choked-off"" active conduits carrying hydrothermal fluids and subsequently acquired an immature alteration signature. Rhyolite units positioned higher in the pile developed intense hydraulic fracturing and a mature alteration coincident with the formation of the stringer sulphide zone. In summary, a model, based strictly upon the rhyolite geology, is reviewed to assist in the exploration for volcanogenic base metal sulphide deposits."

Jan 1, 1985

By Staff

One hundred thousand miles of flying over the North country without a single air casualty; much of it over virgin territory probably never before visited by white men; some of it over regions that abound with possibilities for minerals; all of it effective, for exploration and the establishment of bases and supply-stations, and for the carrying of men and their tools and provisions- this, briefly, is the record of Northern Aerial Minerals Exploration, Limited, a Canadian company organized Jess than nine months ago, which has been functioning, without interruption, during spring, summer, and now into winter. Our planes have ranged from the Alaskan boundary on the west to the Labrador coast on the east, and from the Transcontinental railway north to the Arctic circle. Our prospectors, carried on trips of hundreds, and occasionally thousands, of miles, have gone over large sections of country which were never before explored, and at the end of the prospecting season the Company finds itself in possession of several groups of important gold claims, which look most promising. In addition to this, we have been in contact with deposits of almost every known mineral.

Jan 1, 1929

By Robert B. Parsons

"Two recent decisions by the Canadian courts could reduce the taxes paid by many profitable mines in Canada. At a time when the mining sector is hurting from an ever increasing tax burden and soft prices, the results of two cases are welcome news. Mining companies are well advised to check prior years' tax returns in the context of these developments. IntroductionSince 1976, the income tax legislation has provided a reduced rate of tax for taxpayers engaged in the mining of mineral resources, through the mechanism of the ""resource allowance"". The deduction given for the resource allowance effectively reduces the federal rate of tax by one quarter on resource profits. In general terms, ""resource profits"" are defined to include a taxpayer's income from: the production and processing in Canada of ore to any stage that is not beyond the prime metal stage (or the pellet stage or its equivalent in the case of iron ore); and, royalties computed with reference to the amount of value of production from mining operations in Canada.In computing income from these sources, the taxpayer must deduct expenses that may reasonably be regarded as applicable to those sources, with the exception of expenditures for Canadian exploration and development or financing costs.As a result of the mechanics of the calculation of the resource allowance, one quickly realizes that the lower the expenses deducted from the resource profits, the higher the resource profits and consequently the higher the 25% resource allowance. The impact of the recent court cases is to narrow the range of expenses which are required to be deducted in the determination of the resource profits.The two cases are outlined below."

Jan 1, 1991

By Fan Delian, Ye Jie, Lui Tiebing

The lower and the upper parts of the Doushantuo Fonnation, Hubei Province, China, contain silicate-type K-rich beds (illite and feldspar), and intraclastic phosphorites, as well as Ag-V and V deposits in a "Black Shale Series". The K-rich beds fonned in an anoxic basin whereas the phosphorites fonned in a more oxic and higher energy depositional environment. The Black Shale Series occurs in the lower and upper parts of the Doushantuo Fonnation; that in the upper part consists of black illite shale and dark gray dolostone, and contains Se-rich Ag and V deposits. These deposits are of more industrial significance than the previously discovered Ni-Mo polyelement sulfide deposits which occur in the Lower Cambrian Black Shales Series of South China. Studies of lithotype, sedimentary sequence, and geochemistry of the Doushantuo Fonnation have led to more attention being focused on the uppennost Black Shale Series and its Ag-V and V deposits. There are three ore types: black, Ag-V-rich, illite shale; black, V-rich, illite shale; and dark gray, Ag-Vrich, fmely crystalline dolostone. The first two ore types contain 3070 to 5% Corg and the last, 1.25%. The Ag-bearing minerals are naumannite, argyrodite, aguilarite, acanthite, and native silver that occur as inclusions in pyrite associated with barite. Vanadium substitutes for AI in illite and is also related to organic-matter contents. Because (1) the pre-Sinian Kongling Group contains one to three times greater than the Clark Ag value; (2) black, illite shale has a negative Ce anomaly; and (3) there are large occurrences of black, K-rich, tuffaceous, fme siltstone, the sources of Ag are thought to include subaerial and submarine volcanic materials. It is proposed that Ag, V, and Se were absorbed by clay particles and organic matter during syngenetic deposition in an anoxic environment; Ag subsequently was reconcentrated into sulfides and selenides, whereas V was incorporated structurally into illite during early and late diagenesis. These types of Black Shale Series-hosted Ag-V and V deposits are, therefore, considered to be sedimentary-diagenetic in origin.

Jan 1, 1992

By Brian Hart, Zhe Chen, Liuyin Xia, Mana Pourdasht, Stamen Dimov

"Gold losses related to carbonaceous matter (CM) during processing are a significant problem in the gold processing industry. Inherent CM in gold ores can behave similarly to activated carbon in its ability to adsorb gold cyanide. This phenomenon is termed preg-robbing as the surface adsorbed gold cannot, for the most part, be recovered. Research has identified that gold adsorption by inherent CM is linked to the specific surface area, pore structure, degree of C disorder and surface functional groups. One of the strategies to inhibit CM preg-robbing prior to leaching is a chemical oxidation; a process linked to modification of the surface functionality. In this study, the variability in gold cyanide adsorption due to oxidation with different reagents has been investigated. Variability in gold cyanide adsorption by CM is examined in relation to structural and surface modifications using TOF-SIMS, XPS and Raman spectroscopy.INTRODUCTION A major obstacle for effective gold recovery during carbon in leach (CIL) or carbon in pulp (CIP) processes carbonaceous gold ores is the presence of carbonaceous matter (c-matter) which has the ability to adsorb, or preg-rob gold from the cyanide leach solution. It can be responsible for poor recoveries as the carbonaceous materials (CMs) within the ore competes with activated carbon used during the leaching and adsorption phase of processing (Cay, 2014). Preg-robbing capacity can vary significantly with mild preg-robbing ores showing absorption capacities of less than 1 g Au/t ore, while severe preg-robbing ores may have CM with the capacity to preg-rob more than 500 g Au/t ore (Dunne, 2007). Research by a number of groups have shown that the degree of C disorder has some influence on the ability of the carbonaceous material to adsorb Au(CN)2- (Miller et al, 2005, Helm et al, 2009, Hart et al, 2010). It is also apparent the adsorption characteristics of carbonaceous material is affected by changes in surface chemistry (Dimov, 2016). Various treatment including; flotation to remove the carbonaceous material (Wills, 2010), addition of surface blinding agents (for example kerosene) to passivate or blanket the carbon surfaces (Dimov, 2016), addition of strong adsorbents (eg. activated carbon or resin) to compete with the carbonaceous material and passivation or surface coating by oxidation (pressure, roasting, chlorination and biological oxidation), have been employed prior to leaching in an attempt to minimize the gold losses (Dunne, 2013)."

Jan 1, 2017

By R. A. S Villegas

The Brazilian government announced in 2007 its plans to reactivate the nuclear program. As a result of this decision, a new nuclear power plant is already being built and there are studies dealing with, among other activities, the building of 4 to 8 new ones until the end of 2030. Such increase on the country?s uranium demand affects INB, the Brazilian state company that?s in charge of uranium supply. This paper describes scenarios predicted to the Brazilian nuclear industry for the next years and the INB plans to meet the country?s needs in terms of uranium exploration and production.

Aug 1, 2010

By Clifford R. Stanley

"Abstract - Reproducible analyses of representative samples for elements affected by the ‘nugget effect’ is vital in mineral exploration and reserve estimation. Unfortunately, a priori knowledge of what size of sample is representative from a mineral deposit or its dispersion train is commonly unavailable. Use of the simple ‘equant grain model’ and the NUGGET computer program facilitates determination of the sampling parameters that will produce appropriate samples for chemical analysis. Based on Poisson statistics, NUGGET can be used to determine: (1) the ‘effective grain size’ of nuggets in a suite of samples, (2) the level of representativity (precision) that samples with specific nugget grain sizes will exhibit, and (3) the sample size required to obtain a specific level of sample representativity. The program determines these sampling parameters for any element in any mineral, including solid solution minerals (e.g., Au, electrum, Pt-Fe alloy, diamond), and allows assumption of a variety of grain shapes (e.g., ellipsoids, cylinders, parallelepipeds, etc.). Furthermore, it outputs the effective number of nuggets expected in a sample of given size and the percentile confidence bounds on any element concentration affected by the nugget effect.Results from the software allow determination of effective sampling and analysis strategies that minimize the nugget effect in geochemical analysis/assaying used in mineral exploration and reserve estimation. This will not only improve confidence in the resulting exploration results or reserve estimate, but will facilitate estimation of the error associated with any subsequent interpretation or reserve figure."

Jan 1, 1998

By F. H. Samuel, J. E. Gruzleski, S. Valtierra, H. W. Doty, N. Andrade

In this work, the age-hardening behavior of cast Al-Si base alloys was investigated. It was found that multiple aging peaks are present in the age-hardening curves of Al-Si-Cu-Mg alloys. TEM observations reveal that the age-hardening behavior is related to the precipitation sequence of the alloy. For the Al-Si-Cu-Mg alloy, the first aging peak is the result from the high-density GP zones, while the subsequent are from metastable phases. The transition from GP zones to metastable phases may be the main reason of the formation of multiple aging peaks.

Jan 1, 2006

By J. G. Henning

Following completion of planned mining operations at the Goldcorp Dome Open Pit Mine, a high-grade Shaft Pillar located in the pit highwall was recovered. Mining of this Shaft pillar faced numerous rock engineering design and implementation challenges due to its remote position on the highwall and the presence of mine workings within the wall. The case example presented in this paper discusses the geotechnical investigation performed at the site, novel measures undertaken for installation of ground support required for rockmass reinforcement and for worker protection, as well as operational challenges to successful mining of the Shaft Pillar.

May 1, 2009

By Y. Wang, J. D. Miller, C. L. Lin, Virginia Tech

Conventional flotation machines are typically limited to a particle topsize of 150-200 microns due to inherent constraints created by the pulp and froth phases. To overcome these limitations, a novel fluidized-bed flotation system called the HydroFloatTM Separator has been developed specifically for the purpose of floating coarse particles containing only small amounts of exposed hydrophobic minerals. Over the last decade, this technology has been successfully applied to industrial minerals with several full-scale units installed to recover particles up to and exceeding 3,000 microns diameter. More recently, sulfidebased test work has shown that this novel device is also capable of recovering metalliferous values at a grind size that is much coarser than currently used in industrial concentrators. In the current study, high resolution X-ray microtomography (HRXMT) was used to experimentally compare the degree of exposed grain surface area necessary to recover coarse particles using the HydroFloatTM technology to that attainable using a traditional mechanical flotation cell. The data indicate that exposed grain surface area is a critical factor for coarse particle flotation. For the gold-bearing sulfide ore examined in this study, the HRXMT data suggest that near complete recoveries of coarse (850x500 µm) multiphase particles containing as little as 1% exposed grain surface area were realistically attainable using the HydroFloatTM technology. As such, this new technology may offer a unique opportunity for increasing concentrator capacity by increasing the primary grind size needed for rougher/scavenger separations.

Jan 1, 2016

By A. Y. Senchenko, Y. V. Kulikov

"In recent decades HPGR technology has proven itself in comminution circuits of mining plants. High technical and economic performance, lower specific energy consumption and reliability of HPGR equipment makes it an efficient alternative to conventional circuits using stage crushing and rod/ball milling, as well as to AG/SAG circuits. However, despite all the advantages of this technology the correct selection of key and auxiliary equipment is very important since errors at testing and design stages may lead to discrediting of the whole concept of HPGR application. There is a great variety of possible circuit configurations using HPGR, e.g. with circulation of edge product, with crushing of the whole discharge and circulation of screen oversize, successive two-stage crushing, etc. Each type of minerals will require its own optimal crushing circuit. In this context the testing methodology for selection of an optimal configuration becomes of prime importance. It is common knowledge that the best simulation of material crushing and softening within a HPGR can be obtained only in the course of a large-scale pilot test. The main approaches applied to this kind of testworks are described in this article. Special aspects of HPGR technology design and industrial operation are revealed as well. Some operational issues of HPGR equipment and of circuit as a whole were detected. They are related to regions specifics, plants location, and other factors. Process solutions proposed to deal with these issues are also indicated in the article. INTRODUCTIONDesign and construction of the processing plants involving High Pressure Grinding Rolls (HPGR) technology becomes more and more common in mining as this technology has specific technical and economic advantages against the circuits with autogenous/semiautogenous mills (AG/SAG) and other circuits. The main advantage of the technology is low energy consumption and low operation costs respectively. The presence of microcracks and increased content of fine size fractions in the crushed product contribute to reduction of energy required for further ball grinding. Besides, HPGR technology applies a special wear resistant liner that enables significant reduction of operation costs of grinding media and liner comparing with AG/SAG circuits."

Jan 1, 2016

By G. Zárate, G. Tapia

Anglo American Chile has been doing copper concentrate leaching studies at the laboratory and small pilot plant scale since 1992. Among the processes evaluated are bacterial leaching and pressure leaching using Mantos Blancos, Salobo Project and Quellaveco Project concentrates. Late in the nineties, it was decided to focus the research on pressure leaching, either medium or total pressure oxidation. Preliminary scouting tests were run with Mantos Blancos concentrate samples during 2000, which were repeated during 2003 together with samples of Los Bronces and El Soldado concentrates, in order to define the most suitable concentrate for running a pilot plant campaign at AARL, which was carried out in two campaigns, a first one from November 2003 through January 2004 and a second one during April 2004. Mantos Blancos was the selected concentrate and the laboratory and pilot plant results are discussed in this paper together with some preliminary economic estimates.

Jan 1, 2004

By R. Yost

"This paper describes a case study that illustrates how detailed geological engineering results were communicated to address a range of stability challenges in a producing mining environment. Instead of using standard geological engineering terminology, findings and recommendations were communicated as mine design options and mining responses to accommodate possible slope instabilities and associated risk. The resulting medium- to long-range mine plan integrated the potential slope instabilities and associated mining responses to provide a higher probability of planned resource extraction. It also reduced the potential for long-lasting production and processing delays.RÉSUMÉ Cet article décrit une étude de cas illustrant l’intérêt de la communication de résultats détaillés de géologie appliquée pour résoudre un éventail de difficultés relatives à la stabilité dans un environnement minier en production. Plutôt que d’utiliser une terminologie classique de géologie appliquée, les résultats et les recommandations ont été communiqués sous forme d’options pour la conception d’une mine et de réponses dans le contexte minier permettant de surmonter les éventuelles instabilités des pentes et les risques associés. Le plan de mine sur le moyen à long terme qui a résulté intégrait les instabilités potentielles des pentes ainsi que les réponses connexes dans le contexte minier afin de renforcer la probabilité de l’extraction des ressources prévue. Il réduisait également la possibilité de retards durables dans la production et le traitement.INTRODUCTIONSlope failures in an active mining operation are unscheduled but expected events, in the sense that the geotechnical design often assumes the potential for slope failure but cannot predict exactly when a failure will occur. Unfortunately, the geotechnical engineering cycle—characterization, slope design, displacement monitoring, instability management, and failure remediation—that is necessary to manage slope-failure risk is not always well known or understood outside the geotechnical engineering profession. The first introduction many personnel have to geotechnical engineering is when a slope failure starts to develop and appears to threaten the safety and livelihood of their workplace.At that point, the task of communicating the risk management of slope failure falls to the geotechnical engineer, who must summarize analytical methodology, design concepts, monitoring trends, and analysis results, frequently to an audience with limited exposure to the geotechnical field. All too often, the response has been to present a risk-management plan in the vernacular of geological engineering— using terms such as factor of safety (FOS), pore-pressure reduction, and slope unloading—instead of expressing the problem and solution in more readily understood mine production terms."

Jan 1, 2017

By G. Dörsam, M. Spreij, S. J. Van der Wal, A. P. Schmidt

The transfer of hot metal desulphurising from the torpedo cars to the hot metal ladles at the IJmuiden BOS plant no.2 caused a decrease in ladle lining life from 680 to 470 heats. Changing the desulphurising agent CaC2 for CaO during a trial period, for environmental reasons, led to a further decrease in refractory life. Availability of the ladles became critical and the major reasons for the low life were identified. Solving one of them, temperature, quickly resulted in restoration of the original lives. However, re- introduction of the new desulphurising agent on 50% of the heats again resulted in a decrease, this time from 700 to 550 heats. In order to be prepared for the full introduction of the new agent, thorough investigation of worn linings was conducted, revealing the major (chemical) wear mechanisms. With these findings, a new design for the hot metal ladle is proposed.

Jan 1, 2004

By A. M. Childs, R. F. Mather, K. R. Rawling

"The challenges encountered in the design and construction of mines and their process facilities today are becoming more intense and the engineering more competitive. The need to incorporate new techno1ogy to compensate for ever rising costs is always present, but its application in the harsh environment of Northern Canada increasingly requires the inclusion of new proven methods and innovative approaches to arrive at economically attractive projects.This paper deals with the development of the process design for the Cullaton Lake Gold Mine in the Northwest Territories. Particular emphasis is given to the interaction of the imposed construction and testwork schedules, and their effect on certain process decisions.The challenge that faced the project team may be defined by the following factors:1. A schedule which required that metallurgical testing, engineering, and procurement and delivery of all equipment and construction supplies should be complete within a period of ten months.2. Transportation of all personnel, equipment and supplies to the site by airlift, as no road was available or affordable.3. A six week period when transportation to the site was impossible.4. The extremes of temperature beyond the tree line in the Northwest Territories.5. A complete lack of infrastructure in the area."

Jan 1, 1983

By D. E. Smith, M. K. Murthy

"The commercial potential of a silica-kaolin deposit that occurs on the banks of and close to the Missinaibi River in the District of Cochrane, Ontario, is under evaluation by Algocen Mines Limited. The geological features of the deposit, as well as its probable origin, are described. Mineralogical analysis of the deposit samples indicates that the principal minerals are quartz and kaolinite clay; it is estimated that about 20 per cent of the deposit is kaolin clay. The impurity minerals present are: a slightly magnetic Fe-Ti oxide mineral, goethite, muscovite mica, tour-maline, staurolite, anatase and zircon. Laboratory research studies are in progress to develop and evaluate suit-able methods for the separation of silica sand from kaolin. Results to date indicate that good-quality silica sand with an Fe,03 content in the range of 0.012 to 0.025 per cent can be produced. It appears that the clay portion can also be beneficiated to yield products meeting commercial requirements. It has been possible to beneficiate a portion of theetlay to obtain the particle size distribution now specified by industry. However, research is continuing to develop suitable separation and beneficiation methods which can produce kaolin clay meeting all the commercial requirements."

Jan 1, 1970

By J. Beland

The Rimouski-Matapedia region is along the southwestern extension of the central Siluro-Devonian synclinorium of Gaspe Peninsula. As in Gaspe about 30,000 feet of Siluro-Devonian strata rest on a "basement" of tightly folded Ordovician rocks. The central synclinorium is divided up into two northeasterly trending belts each of which is characterized by distinctive lithologies and patterns of folding. The northwestern belt is gently to moderately folded and includes lithologies which point to a stable environment. The southeastern belt on the other hand is tightly folded and the lithologies indicate a less stable environment. A marked angular unconformity separates the basement from the Siluro-Devonian cover near the north-western margin of the northwestern belt. At the southeastern margin of the southeastern belt the relationship of cover to basement has not been as-certained because of a fault. The northwestern belt has several features significant in the search for petroleum; the Silurian strata are exposed in broad open anticlines

Jan 1, 1962

By V. ?. Chanturiya, I. Zh. Bunin, M. V. Ryazantseva

"Surface changes in naturally occurring metal sulfides (pyrite, arsenopyrite, sphalerite, chalcopyrite, galena, and molybdenite) due to treatments from high-power electromagnetic pulses (HPEMP) at varying times were studied using X-ray photoelectron spectroscopy. Analysis of the obtained results revealed common patterns and differences in surface transformations. The transformations were found to include two main stages. The first stage was observed at low treatment intensities (up to n ~103 pulses). At this stage, formation and accumulation in the surface layer of the nonstoichiometric sulfide phase, oxides and hydroxides, as well as elemental (polysulfide) sulfur and/or metastable sulfur species (thiosulfate, sulfite) was observed. The second stage (N = 3·103 pulses) is characterized by thermal removal of sulfur species and renewal of the mineral surface (sulfidization).It was found that the chemical changes of the sulfur on the surface layer of pyrite, arsenopyrite, chalcopyrite included accumulation/formation of S0 (Sn 2-) at the first stage of the transformation, followed by its removal. An increase in the surface concentration of elemental sulfur for pyrite and chalcopyrite was 10–12% while arsenopyrite was approximately 5%. A more complicated chemical change was observed for sphalerite and galena, that included formation/accumulation of metastable sulfur species (thiosulfate, sulfate) at the initial stage (up to 103 pulses) and during longer treatment times, the sulphur is reduced back to its initial state (sulfide or disulfide). The increased concentration of S0 sulfur, compared to the original sample, was only 3% in galena and sphalerite.The application of HPEMP treatment to improve flotation selectivity is supported by singlemineral flotation tests. Changes in flotability as a result of HPEMP treatment are principally explained by surface phase changes that resulted in higher adsorption activity."

Jan 1, 2016