Search Documents

By Mohammad Noaparast, Babak Fotoohi

"Due to certain advantages in (semi-)Autogenous-Ball mill circuits in most of the high-throughput ore grinding units of mineral processing plants, much attention is paid to optimize the mill performance. Despite the maturity of the grinding mill mechanical design, there had been made less attention to the efficiency of the grinding media in the past. In this research, the possibility of establishing a relationship between liner/lifter wear rate and variations in the composition of the iron ore (from Chadormalu mine) is investigated.Measurements and determination of liner/lifter wear rates and patterns concluded in recognition of critical liner segments exposed to much abrasion during the ore grinding. After metallurgical analysis of liner materials and correlation of wear rate with the ore composition, the homogeneity in the metallurgical microstructure of the alloyed steel (such as the uniform distribution and amounts of the constituent phases) was determined as the most influential factor in the response of the liner/lifter to the variations in the ore composition. Magnetite with greater abrasion index than hematite, in finer particles, is responsible for additional abrasion of liners; hematite with greater work index exists in the mill with larger particle sizes, thus it could produce wear on liner parts with less tolerance to impact as is the situation for martensitic steels.INTRODUCTIONThe mineralization in Chadormalu plutonic iron ore deposit is consisted of mostly magnetite, hematite, martite, apatite, quartz and carbonates. The average composition of the ore is presented in Table 1. In the processing circuit, the gyratory crushed ore reduced to 30 cm would finally be the feed to three similar 32’ semi-autogenous mills in parallel processing lines. The pulp in the mill would have the characteristics mentioned in Table 2. The quality of the mill output has its direct effect on the downstream processes either physically or chemically (e.g. in cycloning or flotation respectively). In order to take advantage of optimum performance for these circuits, a close control of the ore grinding conditions is necessary; because any shortages in throughput, liner/lifter damage or changes in ore composition could bring the unexpected casualties. In this work, it has been attempted to find (possibly) a reasonable relationship between variations in ore characteristics together with liner quality and the amount of wear rate in different liner/lifter segments of a semi-autigenous mill. Liner/lifter segments are supplied by three different domestic steel making companies. The alloy structure of the liners/lifters is made up of pearlitic chromoly steel."

Jan 1, 2005

By W. Kempson

"As has been noted on numerous occasions, the vertical shafts being sunk around the world are all tending to get deeper as we seek to take advantage of higher grades of minerals which can sometimes be found at greater depths. One of the challenges with these deeper shafts is the requirement to supply services to the mine’s operations at depth as well as the requirement to dewater the mine. Both the supply of water and the dewatering of mines is generally done using piping. With the greater shaft depths, this piping is now required to contain higher pressures as well as to accommodate changes in temperature resulting from normal mine operations. This paper will discuss the requirements for the design of high pressure piping in deep vertical shafts. The discussion will start with the general definition of the systems and the detailed design requirement. Once this is clearly outlined, we will discuss the options available for fulfilling these requirement as well as the advantages and disadvantages of each of the systems. We will finish with the installation recommendations and provide a basis for the maintenance of these systems. INTRODUCTION Piping in vertical shafts is used to provide a number of services in underground workings. These services vary depending on geographical location and the type of the ore body which is being mined. For example, in the Zambian Copper mines, one of the largest requirements for in shaft piping is for dewatering. Similarly in the Gold deposits in the West Wits basin as well as the deep level Copper deposits in Arizona, one of the largest uses for the piping is the supply of a cooling medium to underground workings to create a safe working environment (this can in the form of water or of glycol depending on the application). In South Africa, systems were installed which used the hydrostatic head which is generated from supplying chilled water to mines whose depths exceeded 2,000 m below surface. This chilled water was supplied as a closed system, allowing for high pressures to be generated which was then used to supply useful work (for example, Rock Drills, Face Cleaning and other ancillary services) whose power was traditionally supplied by compressed air or electricity. This system was initially researched by Chamber of Mine in South Africa. The design pressure range of these systems is 14 MPa to 18 MPa."

Jan 1, 2019

By Norman O. Lotter, Lori Kormos, Greg J. Wilkie, Peter J. Whittaker, Johannes S. Stickling

"Assessment of opportunities to improve mineral processing performance in existing concentrators and in describing undeveloped orebodies is key to improving the business case of a mining company. This assessment has traditionally been performed using the distinct and separate inputs from Mineral Processing and Mineral Science.More recently, Process Mineralogy has been used to integrate these two disciplines. This trend has been driven by the need to develop and process more challenging ore deposits, and has been assisted by the availability of modern automated instruments. Together with the acquisition of a QemSCAN (Quantitative Evaluation of Materials by Scanning Electron Microscope) from CSIRO in Australia, and with the use of a supporting SEM with EDX / WDX capabilities and an XRD, the development of Process Mineralogy at Falconbridge commenced in 1997.The sampling challenges in presenting a QemSCAN with representative sample material at the polished section level are significant, but have been effectively addressed. The full description of this aspect is beyond the scope of this paper.It is shown that, by use of this approach, the set nature of an orebody can be best exploited with selected flowsheet changes in a concentrator which address the generic characteristics of the orebody. In this way, the flowsheet provides a process that more effectively fits the mineral processing requirements of the ore. This leads to clear and tangible improvements in grade and recovery."

Jan 1, 2002

By E. V. Konopleva, H. J. McQueen

Steels in high variety have been providing strength and ductility for more than a century mainly through complex heat treatments following hot shaping. The economical and sustainable goal was a steel with the two operations combined through applying knowledge of dislocations and strengthening mechanisms aided by new mechanical and microstructural techniques. Primary hot reversing-mill rolling produced static recrystallization (SRX) between every pass to significantly finer grain size. Hot torsion showed that with lay-on temperature and rate of reduction suited to gradual precipitation of minor additions of Nb, the austenite grains would become highly pancaked; the existence of very fine subgrains along the grain boundaries (GB) could be deduced from tests on stainless austenite. The HSLA strip had to be water-jet cooled immediately to prevent SRX at austenite GB and ensuring complete transformation to ferrite avoiding grain growth after coiling. Confirmation on old mills and successful product led to the design of more flexible mills for wider range of compositions and products. A significant one was auto bumpers that reduced crash damage. More crack-resisting compositions were developed for strip welding into line pipe for arctic oil transport. Lower metal consumption and easier fabrication has resulted in more sustainable welded bridging.

Jan 1, 2015

By W. J. D. Stone

"For several years, the existence of a deposit of barite (BaS04) near Brookfield, Nova Scotia, has been known. A very large deposit of strontium (SrS04) near Sydney, Cape Breton, is a more recent discovery. Cape Chemical Syndicate has been formed to work the deposits. A five-million-dollar integrated mineral processing and chemical plant is planned for Sydney to produce various compounds of barium and strontium. The mineral processing plant includes the Jones Wet Magnetic Separator and will produce high-purity barite and celestite. These products will be processed further in the fine grinding plant and the chemical plant. The general project is described, covering the deposits, processing and markets."

Jan 1, 1969

By T. Newton, G. A. Bezuidenhout, P. J. Tauetsile, F. Trask

The technology to selectively leach gold, silver and base metals from ores, concentrates, and wastes, using an alkaline glycine solution, has initiated significant interest in using the new technology in various environments such as in-situ, in-place, dump, heap, and vat and agitated tank leaching. It has been shown that glycine acts synergistically with a number of other lixiviants to lower the net consumption of the other lixiviants while allowing low cost glycine solution recovery. Glycine is a non-toxic, stable, environmentally benign reagent that is available in bulk industrial quantities. It has the ability to dissolve most copper oxide and sulfide minerals, as well as native copper, whilst not interacting with acid consuming gangue nor dissolving iron and various or ubiquitous gangue elements. It acts synergistically with small amounts of cyanide to leach gold-copper ores at leach rates higher than either glycine or cyanide on their own, while significantly reducing cyanide consumption and eliminating detoxification requirements. The leaching behaviour of various glycine based systems will be reviewed, followed by the evaluation of the adsorption of gold onto activated carbon. Where the economics merit it, copper can be easily recovered using solvent extraction or sulfide precipitation.

Jan 1, 2017

By P. K. Kaiser, C. D. Martin, F. Amann

"This article focuses on the uniaxial compressive strength (UCS) of homogeneous and heterogeneous rocks. Critical factors impacting the UCS of rocks are reviewed and then separate assessments of UCS data from homogeneous and heterogeneous rocks are presented. The variability (coefficient of variation) of UCS test results for homogeneous rocks is found to be generally <25% while for heterogeneous rocks the variability is >35%. Failure mode variation is found to be the cause of the variability of UCS test results in heterogeneous rocks. Empirical engineering design methods that use UCS as an input parameter are discussed and suggestions are provided for selecting appropriate UCS values.INTRODUCTIONThe UCS is one of the most commonly used rock engineering parameters whether for rock mass classification or for strength determination. The mean UCS and its variability are often assumed to represent a reliable rock material property. For the reasons discussed in this article, UCS is rarely representative of the intact rock UCS. The UCS test simply records the collapse load during uniaxial loading of a cylindrical specimen. As suggested by many, the UCS is an index rather than a unique engineering parameter. The UCS is thus a proxy for rock strength which depends on the loading rate (e.g., Bieniawski 1967), specimen geometry (e.g., Hudson et al., 1971), specimen size (e.g., Bieniawski 1968), and many other factors. Furthermore, the UCS is not the same as the Hoek-Brown strength criterion parameter sci.There are differences in opinion on what is commonly considered to be ‘intact rock’. When sampling ‘intact’ pieces of core from drillholes crossing blocks of rock bound by block forming discontinuities, samples will be ‘intact’ but some samples will be veined, others will be damaged, and others will be neither. According to Hoek (1983), intact rock pieces are “the unfractured blocks occurring between structural discontinuities in a typical rock mass” and the sci parameter for intact rock is determined using the fitting procedure proposed by Hoek and Brown (1997) based on the data requirements outlined by Hoek (1983). Studies (e.g., Bewick and Kaiser 2014; Kaiser and Kim 2014) have shown that independently determined UCS and sci values for the same rock type are not equivalent. Thus, UCS data cannot be used as a replacement for sci."

Jan 1, 2015

By L. Nutter, J. Clancy

"Barite is used extensively by the oil and gas well-drilling industry as a weighting agent. It is particularly well suited for drilling mud because of its qualities; it is non-abrasive, heavy, virtually inert chemically, easy to handle and inexpensive compared to other available heavy materials. Increased deep well drilling in Western Canada, and especially in the Arctic regions, could dramatically affect the demand for barite through this decade. Known deposits in northeast British Columbia are possible sources of incremental barite supplies, should the situation develop.IntroductionThe purpose of this report is to examine the opportunities for expanding barite production in British Columbia. Of primary interest will be the relationship between the projected future levels of production and consumption of barite in Western Canada and the extent to which increased domestic production could replace the need for imports in filling any expected supply shortages.After a brief overview of the nature and uses of barite and some of the relevant features of the barite supply industry, the discussion will turn to the supply gap in the Canadian market and the possibilities for import substitution.OverviewBarite is an industrial mineral which is used in large quantities by the oil and gas well-drilling industry. It is often an important component of drilling mud, a fluid circulated continuously in the well during the drilling process to lubricate and cool the drilling apparatus and to contain the high oil and gas pressures found at depth. Barite (BaSO4) is particularly well suited as a weighting agent for drilling mud because it is a heavy (specific gravity to 4.5) inert mineral which is inexpensive in relation to other materials having a high specific gravity. In the on-site use of drilling mud, ground barite is combined with numerous other solid ingredients and chemicals in the form of a slurry. Other advantages of barite include cleanliness, ease in handling and its non-abrasive character (hardness of 3-3.5)."

Jan 1, 1982

By Howard Keele

"The Whitewood Mine near Edmonton, Alberta, is owned by TransAlta Utilities Corporation and operated by Manalta Coal Ltd. Approximately 2 million tonnes of sub-bituminous coal is supplied annually to the Wabamun Generating Plant. A high water table, high groundwater pressure, and structural folds contribute to stability problems in the fine-grained overburden. Significant increases in coal recovery have been achieved in recent years through improvements in water management and mining methods. Agricultural capability of the post-mining landscape has also been improved following the completion of mining/ reclamation activities. Introduction The Whitewood Mine, located to the north of Lake Wabamun and seventy kilometres west of Edmonton, Alberta, is owned by TransAlta Utilities Corporation and operated by Manalta Coal Ltd. Figure 1 shows the location of the Whitewood Mine with respect to the city of Edmonton. The mine presently supplies two million tonnes annually of sub-bituminous ""C"" coal to the 582-megawatt Wabamun Generating Plant located adjacent to the mine. The area is characterized by a high water table-, rolling coal seams and an overburden that consists of muskeg, clay and various sedimentary layers of sand, gravel and fine-grained sandstone. These distinctive characteristics require careful attention in order to not only meet the coal delivery requirements of the Wabamun Generating Plant but also to do so economically. Historical Background A small-scale underground coal mine was opened in the Wabamun area in 1910 by the Conner Coal Mining Co. Ltd. Underground operations were continued by several operators until 1948 when the Alberta Coal Co. Ltd. opened a strip mine which was subsequently taken over by the Alberta Southern Coal Co. Ltd. in 1951. The small-scale strip opera"

Jan 1, 1985

By Jiwen Zhang

Abstract Due to the blocking nature at the crusher station, straightforward application of queuing theory cannot give realistic results on the performance of a shovel-truck-crusher system. A new queuing network-based model has been developed in which, the crusher station is formulated into an open queuing network and the whole shovel-truck-crusher system into a closed queuing network with the crusher station as a special server. To fully account for the influence of blocking, Monte Carlo simulation is first used to obtain the performance parameters of the open queuing network for the crusher station. The closed queuing network for the entire system is solved by applying the Extended Summation Method (ESUM), in which the crusher server is described by the simulation results. The model has been applied to the Yuanbaoshan open-pit coal mine to analyze its shovel-truck-crusher system and to improve its efficiency. Results indicate that the blocking at the crusher is an important factor affecting the crusher output and in turn the efficiency of the whole system, and prove that the model can realistically describe the behavior of such systems.

Oct 1, 2009

By K. M. Tait, M. M. McDonald

"An overview of the status of the development and application of Integrated Gasification Combined Cycle (IOCC) power generation is presented. Current projects in North America, Europe and Japan are described, together with the status of plans to apply the technology in Canada. A brief review of the technology is presented, including promising coproduction cycles and hybrid gasification fluid bed processes. The ability of the process to be modified for CO2 to be extracted for enhanced oil recovery or disposal is addressed. The environmental impact of IGCC technology is compared to those of other power generation technologies IntroductionDefinition and HistoryIntegrated Gasification Combined Cycle (IGCC) technology is a concept which has been around for about 50 years but has been generating increasing interest in the last 10 to 15 years. This paper focusses on coal as the feedstock for gasification. Other feedstocks used in gasification systems have included oil, biomass, tires and petroleum coke. IGCC technology integrates coal gasification with generation of electricity by means of a combined cycle system which fires the produced gas in the gas turbine. Figure 1 shows the basic components of an IGCC system which are the gasifier, the gas cleanup system and sulphur recovery plant, the gas turbine/generator set, the heat recovery steam generator (HRSG) and the steam turbine/generator set. The benefits of an IGCC system over a conventional Rankine Cycle pulverized coal (RCPC) fired system for the generation of electricity from coal are that the IGCC system has potential to have higher efficiency and lower emissions of NO., SO and CO2 per unit of power produced than the corresponding RCPC system."

Jan 1, 1994

By J. A. McCamley

Gypsum scrap generated from wallboard manufacturing, construction and deconstruction activities in North America, Europe and Japan is a recognized environmental problem. Landfill disposal of this gypsum scrap is problematic, with deposits often creating hydrogen sulphide emissions and metallic sulphide groundwater leachates. Of these regions, Europe is the most advanced in dealing with the issue having enacted legislation, which will come into effect in July 2005 that will strongly encourage gypsum recycling throughout the EU. An estimated 10% to 17% of all gypsum used in the wallboard industry becomes recyclable scrap, which represents approximately 1% of the total waste stream in North America. In the United States, 2.5 to 4.5 Mt of gypsum scrap is generated each year; the volume is similar in Europe (the percentage of total tonnage is less because of the higher use of brick and concrete). The Greater Vancouver region of British Columbia has banned gypsum from its landfills, and as a result, all gypsum scrap is now recycled. New West Gypsum Recycling, a Canadian firm, uses its proprietary technology to process large quantities of gypsum scrap that is reincorporated into new wallboard, at percentages ranging up to 25%. The operation of New West Gypsum Recycling Inc. of Langley, Vancouver is examined as a case study and recommendations are provided as to how other urban regions can implement similar gypsum scrap recycling programs.

Jan 1, 2004

By G. D. Garland

The influence of natural electric currents, induced in the earth by changes in the earth's magnetic field, on the electric logging of boreholes has not always been recognized. Measurements made with fixed electrodes of changes in the vertical potential gradient in a hole near Calmar, Alberta, have indicated the effect of earth currents related to magnetic disturbances. It is found that appreciable errors in self-potential logging could arise during periods of magnetic storms, but the precise pat-tern of disturbance in any area seems to depend on the local structural conditions. As the amplitude of the natural earth currents increases toward the auroral zone, it is suggested that periods of magnetic disturbance be avoided, if possible, when electric logs are taken in the northern part of the western sedimentary basin. NATURAL electrical currents flow continuously near the surface of the earth, apparently as a result of electromagnetic induction

Jan 1, 1962

By M. Leroux, C. J. Martin, S. R. Rao, J. A. Finch

"The effect of nitrogen on the flotation separation of sulphides from complex ores from Brunswick Mining and Smelting (New Brunswick) and Mattabi Mines (Ontario) was investigated. The most significant finding was enhanced pyrite floatability after as little as 3 minutes nitrogen conditioning. This was used in a novel sphalerite/pyrite separation process developed on the Brunswick ore. After aeration and Cu/Pb bulk flotation in air using xanthate the slurry was nitrogen conditioned, xanthate added and the pyrite floated in nitrogen. As an example up to 70% pyrite recovery with about 20% sphalerite recovery was achieved. Sphalerite was recovered from the pyrite tailings and the pyrite concentrate by copper-activation, raising the pH to 10 and floating in air. About 65-70% recovery at 35-40% Zn grade was achieved compared to 25% Zn grade by the conventional route. The process offers a promising alternative to current practice which seeks to depress pyrite at all stages. A possible mechanism of the effect of nitrogen is presented. INTRODUCTIONUse of gases other than air in froth flotation has been reported from time to time. [Podobnik and Shirley, 1982; Lin and Metzer, 1975]. Of all the gases, nitrogen would appear to hold the greatest practical promise because of its easy availability and chemical inertness. It is used in froth flotation in chalcopyrite-molybdenite separation [Redfearn, 1983]. The use of nitrogen in polysulphide chalcopyrite. this case is mainly to reduce the oxidation of a compound (Nokes reagent) used as a depressant for There is no reported use of nitrogen in the flotation of other sulphide minerals."

Jan 1, 1988

By J. A. Finch, G. Labonté

"A long-standing objective has been to obtain interpretable measurements of the oxidation-reduction potential in mineral slurries. For this purpose several sensing electrodes (black platinum wire, platinum foil and spiral, gold foil and spiral, and sulphide minerals such as chalcopyrite and galena) were investigated to determine their response to the presence of sulphide minerals in the pulp, and to the addition of reagents commonly used in flotation. The observed discrepancies between the electrodes may be explained using a combination of the classical mixed potential model for complex solutions and the probability of contact between the mineral particles and the sensing electrode. It is shown from laboratory testwork that gold spirals are preferred over platinum electrodes. Finally, some of the practical aspects of using the electrochemical measurements in a plant environment are discussed.IntroductonThe interpretation of flotation of sulphide minerals in terms of electrochemical (electron transfer) processes has brought new possibilities for process control of selective flotation. Investigations on massive and compacted particulate bed electrodes have shown that the flotation of a given mineral in the presence of a collector can be controlled by the potential induced on the mineral surface. Also, phenomena such as collector less (self-induced) flotation, activation by heavy metal ions, and natural selectivity sustained by galvanic coupling during flotation might also be controlled by electrochemical means.The technique for measuring electrochemical potential in slurries is an adaptation of that used for solutions. The measurement of the oxidation-reduction potential of a solution (ORP , Redox, Eh) is usually carried out by immersing a noble metal electrode (platinum, gold or silver) and a non-polarizable reference electrode: Standard Hydrogen Electrode (SHE), Standard Calomel Electrode (SCE), or silver/silver chloride (Ag/AgCl) in the solution. (The abbreviation Eh implies the SHE is the reference electrode.) The potential difference between the two electrodes is measured using a high impedance electrometer. ASTM standard D 1498-76 (revised 1981)(1) covers the practical details of such measurements; however, it does not deal with their meaning either in complex solutions or in mineral slurries ."

Jan 1, 1988

The topic of the relationships between energy and particle size has had two very active periods -the first in the early thirties, when the relative merits of Rittinger&apos;s and Kick&apos;s proposals were vigorously debated; the second in the early fifties, when Bond&apos;s Third Theory was published. This second stage has produced several contributions that have provided a clearer picture of energy /size correlations in comminution. Derivations of a general relationship have been made from single-fracture experiments and from the rate of comminution, and both methods arrive at an equation of the type E = AK-11? The constant A in the equation may be regarded as a grindability parameter. In some respects, an understanding of the phenomena associated with comminution is still lacking, and research in this field should therefore be expanded. T HE SEARCH for a relationship between the energy consumed in comminution and the size of the broken product has been long and varied, and many

Jan 1, 1964

By D. R. Schmitt, Q. Jia, R. Kofman

"Tests were carried out on clear glass blocks containing borehole aligned with and at an angle to applied principal stress states in order to study the growth of drilling induced tensile fractures. The samples were illuminated such that photoelastic fringes could be video recorded during the measurements; this was useful in assessing states of stress and in determining fracture initiation. Axial drilling induced fractures were observed at the azimuths of the applied uniaxial stress as would be expected from the concentrated stresses. En echelon fractures were observed from the borehole deviated at 45° to the direction of the compression. These preliminary and currently qualitative results show that glass blocks serve as a useful test medium for studies of stress concentration and drilling induced fracture creation. INTRODUCTIONWith the increasing exploitation of unconventional oil/gas reservoirs using deviated drilling in recent years, the effects of the in-situ stress on the success of energy production have become more critical than ever before. Knowledge of the state of stress in the earth enables us to determine well trajectories, well locations, hydraulic fracturing design and production rates, but knowing the crustal stress is always challenging. Strictly, it can only be obtained to varying quantitative degrees by accessing the earth through drilling. Failure of the rock at the borehole wall produces borehole breakouts (e.g., Bell & Gough, 1979; Haimson & Herrick, 1986; Zoback et al., 1985) and drilling-induced tensile fractures (DITF) (e.g., Aadnoy, 1990; Aadnoy & Bell, 1998; Barton et al., 1997; Brudy & Zoback, 1999; Davatzes & Hickman, 2010; Peska & Zoback, 1995). Thus, it is important to understand the failure mechanism of the rock in the vicinity of the borehole. A number of closed-form expressions have been developed that allow the stress concentrations to be calculated in the vicinity of a borehole including Kirsch’s (1898) 2-D plane strain solution and 3D formulae for elastically isotropic (Hiramatsu and Oka, 1962) and anisotropic (Lekhnitskii, 1981; Amadei, 1983) continua. These solutions have been applied in numerous studies (e.g., Ong, 1994; Ong & Roegiers, 1996; Vahid & Ghassemi, 2011; Jia & Schmitt, 2014; Ito et al., 2001) to analyze the failure mechanisms of drilling-induced tensile fractures (DITF) on the borehole wall."

Jan 1, 2015

By Z. Y. Ma, H. Y. Yang

The process of microwave-ultrasound assisted leaching of valuable metals from copper anode slime was proposed in this paper. Design of experiments has been used to study the effect of the main leaching parameters, such as microwave power, ultrasound power and reaction time. The central composite design (CCD) was used to predict the maximum leaching efficiency of copper, tellurium and selenium. The experimental data obtained were fitted to a second-order polynomial equation, and they also were analyzed by analysis of variance (ANOVA). The 3-D response surface plots and the contour plots were applied to determine the optimal conditions. The optimum conditions of microwave-ultrasound assisted leaching process were: microwave power 834W, ultrasonic power 638W and reaction time 403s. Under these conditions, the experimental leaching efficiency of copper, tellurium and selenium were 98.88±0.56% 98.96±0.78% and 98.57±0.67%, respectively, which agreed well with the predicted values.

Jan 1, 2014

By MacKenzie Dickson

"INTRODUCTIONGold is found in many natural states, native nuggets, loose grain in river sands, veins in rock, as well as associated with sulphides, oxides, etc., disseminated more or less minutely.Its high value in recent years has spawned new technologies to win values from sources once considered too lean for commercial recovery. Cyanide leaching from fine milled ore or tailings, from upstream recovery operations, coupled with adsorption onto relatively coarse granules of activated carbon, concentrate the gold enough to be converted to bullion by time-honoured methods.The carbon granules are fragile. Size degradation in handling must be minimized not only to prevent loss of gold on fine fragments of carbon that could pass with the barren tailings, but to maintain adsorption efficiency. Besides, the granulated carbon itself is costly. Circular Vibroscreens are winning acceptance for dewatering carbon granules thanks to their gentle yet effective performance in gold recovery systems around the world. The system at Equity Silver is illustrative.BackgroundEquity Silver Mines Ltd., Houston, British Columbia, first began production in September 1980. In 1984, a feasibility study showed that additional gold and silver could be economically recovered through cyanide leaching of the flotation tailing.Although the carbon-in-pulp (ClP) or carbon-in-leach (CIL) process is commonly used for extracting precious metals from slurries, the use of circular vibrating screens, and Vibroscreens in particular, for the carbon circuit is an innovation that cuts costs.Rectangular vibrating screens have been the conventional separation mechanism of choice across North America. In contrast, the use of Vibroscreens has been proven to be less costly for the initial purchase and installation. Also, these circular vibrating screens require less power and less space. A description of Equity Silver Mines&apos; process shows how these screens have been successfully integrated into the system."

Jan 1, 1989

By Amyn S. Dahya, David J. King

"The object of the paper is to discuss the developments in Carbon-In-Pulp (C.I.P.) technology for gold recovery. The CIP process is comprised of four major operations:(a) adsorption of precious metals onto activated carbon;(b) elution (stripping) of precious metals from the loaded carbon;(c) electrowinning of the precious metals from the concentrated eluate;(d) regeneration of the eluted carbon before recycle to the adsorption process.A detailed review of the technological developments in each of the above operations is presented together with a brief theoretical background of the underlying processes. The advantages and disadvantages of the CIP process are discussed in comparison with conventional zinc precipitation. IntroductionThe carbon-in-pulp (CIP) process involves the use of activated carbon for treatment of pulps containing dissolved precious metals, and provide s an alternative to the conventional gold recover y processes using filtration or counter-current decantation in conjunction with the Merrill-Crowe zinc precipitation process. The commercial application o f the CIP process in gold processing technology is a fairly recent development and it is of growing importance around the world.The fact that activated carbon ha s the property of adsorbing precious metals from solution was first published in 1847. In the following years , a great deal of work was carried out to develop an over-all recover y process using carbon, but all attempts were uneconomical because the loaded carbon had to be smelted to recover the gold.It was not until 1950 that Zadra, at the United States Bureau of Mines Research Centre in Reno, Nevada, developed a technique for stripping the loaded carbon using sodium sulphite-sodium hydroxide mixtures and then recovering the gold from the stripping solution by electrolysis. However, this process was not effective for stripping silver and further testwork was carried out on alternative stripping techniques. In 1952, Zadra published a paper describing the use of a hot sodium hydroxide- sodium cyanide stripping technique, which was effective in stripping both gold and silver. This paper included a description and flowsheet for the CIP process which is essentially the same as we know it today. This technique was used in the first major CIP plant, constructed and commissioned in 1973 by Hornestake Gold Mining Company. Since then there have been numerous CIP plants built in the U.S A., South Africa and Australia."

Jan 1, 1983