Search Documents

By K. J. Heale, G. G. Richards, D. J. Rioux, R. L. Stephens

Slag fuming has remained a key process for the recovery of Zn, Pb, and minor elements in the integrated flow sheet at Teck Cominco's Trail Operations for more than 75 years. Since the start-up of the KIVCETTM process and the #3 slag fuming furnace in 1997, a range of process intensification projects have been completed to improve metals recoveries and throughput based on improved process control, mechanical modifications, and, most recently, the implementation of oxygen enrichment of the blast air. This latter project, initially named 'nitrogen depletion' and now 'nitrogen oxygen performance enhancement' (NOPE), is the primary focus of this paper. NOPE reduces the amount of heat required to heat the inert nitrogen gas, and therefore more of the energy input can be used for reduction. It also frees up boiler capacity because the inert nitrogen gas does not then have to be cooled down. A dynamic METSIMTM model was developed to determine the opportunities to improve the process capacity and heat balance to both assist with justifying the project and to verify the observed furnace behaviour. Several process safety management issues were also addressed and a few key minor mechanical modifications were made to allow the project to proceed to commercial implementation at 25% blast air oxygen enrichment. Short term plant trials have confirmed the model predictions. The first three months of a long term, continuous trial showed a 6% increase in zinc fuming rate from average furnace performance despite the implementation of a KIVCETTM fluxing change to assist with minor element recovery that was expected to negatively impact the zinc fuming rate by 3 to 5%. This encouraging result is also in line with the model predictions.

Jan 1, 2008

By M. Moats, J. A. Gonzalez

A review of operating practices in zinc electrowinning plants is presented in this paper. Surveys were sent to several zinc electrowinning plants and data provided by some of these plants was compiled in a database. Information about anodes and cathodes, electrolyte composition, stripping methods, cells, electrical systems, and additives was compiled and analyzed. From the data analysis, correlations between operating variables are presented. Recent trends in operational practices are also highlighted.

Jan 1, 2008

By F. Habashi

Lead is an ancient metal. The alchemists related it to the planet Saturn. It was largely obtained by smelting galena which generally contains small quantities of silver. That is why the metallurgy of lead was closely related to that of silver and in some cases the ore was treated only for its silver content. It was also known during the Roman time that lead vapors were toxic. Lead has been produced exclusively by pryrometallurgical methods. Lead refining is a complex process because of the presence of deleterious impurities such as arsenic, antimony, and bismuth. In the nineteenth century lead played an important role as a material of construction in the manufacture of sulfuric acid. In the twentieth century tetraethyl lead was used exclusively as an anti-knock reagent. In recent years lead is mainly used for making batteries.

Jan 1, 2008

By P. Henry

Hydrometal provides an adequate technology to reintroduce lost metal units into the industrial cycle, thereby saving resources and energy, while keeping the environment cleaner. Two case studies of our integrated hydrometallurgical recycling facility (Hydrométal) in Belgium are discussed.(I) Recycling of Cu-Co cement generated at the second purification step of zinc sulfate solution. (II) Recycling of lead complex materials from the lead industry.

Jan 1, 2008

By L. Parthasarathy, S. K. Pan, M. P. Srivastava

"Total iron ore reserves in India, as reported by the Indian Bureau of mines, are 23.6 billion tons. Hematite iron ore reserves constitute about 45 % of the total reserve. If we go by the National Steel Policy-2005 projections, India’s supply of hematite iron ore would not last more than 40 years. Laboratory investigations were carried out for the development of a process flow sheet for treating low grade as well as Banded Hematite Quartzite (BHQ) iron ore. The purpose of these investigations was to aim for better resource utilization.Beneficiation studies were conducted on samples of low grade and siliceous iron ore from the Dalli mines, a captive mine of the Bhilai Steel Plant and BHQ ore from Southern states of India. The process flowsheet, developed for upgrading of low grade iron ore, incorporates wet screening of the ore at 0.5 mm, followed by grinding of the +0.5 mm fraction to below 0.5 mm. The whole –0.5 mm fraction, after grinding, was treated in a conventional hydro-cyclone and stub cyclone followed by treatment in Wet High Intensity Magnetic Separator (WHIMS). This resulted in a concentrate product having >66% Fe content from a feed containing 55.5% Fe with an iron recovery of 48 %. The process flowsheet developed for treating BHQ ore in the laboratory resulted in an increase in iron grade in the concentrate from 43.4 to 61.3 Fe % with a yield of 51.7 % .INTRODUCTIONThe classification of Indian iron ore resources have been made compatible with United Nations Framework Classification (UNFC), which is more scientific and has been adopted in most countries in the world. Iron ore reserves and resources estimated using the UNFC classification system, as of April 01,2000 are about 12,906 million tons of hematite ore and 10,628 million tons of magnetite ore. The Indian Bureau of Mines (IBM) has given a breakdown of these reserves by designation as either lumps or fines of hematite iron ore (Table 1). The percentage of the reserves reported lumps and fines are 42 and 34% of the total reserves respectively. High grade iron ore is less than 10% of the total reserve."

Jan 1, 2008

By Robert K. Jonas

"Minerals processors can improve production by using the best available control technology to control their operations. Many mines use expert systems that can provide improved results over manual or basic control, but better results can be achieved using multivariable predictive control. Over the past few years, the application of multivariable predictive control has gained acceptance in many mining processes and has recently proven to be suitable for some of the most challenging processes. This advanced control technology has been successfully applied to a wide variety of processes; alumina digestion, ball mills, CCD/thickeners, kilns/calciners/roasters, heat exchangers/evaporators, and more demanding processes like SAG mills and flash smelters.This paper discusses the needs of advance control technologies in the mining industry, including the impact of these technologies on best practices for implementation and long term sustainability. Results of the multivariable predictive control applications in mineral processing are discussed, and in particular the application to the SAG mill. In addition, an example of the benefits improvement that can be achieved with this technology is presented.INTRODUCTIONThere has been a long term perception in the mainstream mineral processing industry that best advanced control solution is an expert system. There a numerous instances of expert systems used for control of SAG mills, as well as kilns or roasters, thickeners and more recently flotation circuits. Many of theses expert systems have been installed by small, independent companies or by OEMs of processing equipment. Undoubtedly these expert systems have provided millions in benefits to the owners of mineral processing plants.It is this author’s proposition that it is a misconception to believe that expert systems are the best solution for mineral processors, and that in many cases the best solution is Multivariable Predictive Control (MPC). Better control and optimal operations can be achieved through the use of MPC. Another important consideration when considering advanced control technologies is the implementation and support effort. These types of applications have been known to deteriorate, even to disuse, when they are not kept up to date with changes to the process or equipment. The audience is invited to listen to discussion and draw their own opinion. The author has been involved in installing control systems for over 20 years, advanced solutions for over 15 years, and has had privilege to consult with many miners concerning the selection and application of advanced controls over the past 6 years."

Jan 1, 2008

By T. Liu, C. Shi, T. Fu, M. Zhong

Water inrush in coal mines is induced by the imbalance of the groundwater flow field and the engineering geo-mechanics field. Therefore, to prevent water inrush it is important to predict the critical hydraulic pressure of water inrush in coal seam floors. This paper will investigate a method for conducting theoretical forecasting of the critical hydraulic pressure of water inrush in coal seam floors by adopting the combination method of a genetic algorithm-neural network. First, the topology structure of a neural network (NN) based on genetic algorithms (GA) will be determined and then the critical pressure of water inrush in a coal seam floor using the chosen NN will be predicted. Finally, theoretical forecasting results will be compared with actual measurement results to determine the feasibility and applicability of this method.

Jan 1, 2008

By R. Matusewicz, A. Kaye

Ausmelt Top Submerged Lancing (TSL) Technology has gained widespread commercial acceptance in non-ferrous applications, including the processing of lead and zinc primary concentrates and secondary (post-consumer) materials. TSL is highly flexible and efficient, and is one of the few technologies which can process primary and secondary feeds, and use varying fuels, to deliver high recoveries and excellent environmental performance. With the recent high value of both lead and zinc, and an escalating awareness of the sustainable use of resources, focus on the processing of secondary feed material sources has surged. Ausmelt Technology has proven to be well suited to the economic recovery of values, with twenty-two (22) Ausmelt furnaces processing lead and zinc bearing feed sources now in operation, under design or construction. This paper describes Ausmelt's progress in the fields of lead and zinc processing, and developments in new processing areas such as EAF dust processing and linking to innovative hydrometallurgical technology. Ausmelt has recently committed to the Whyalla Zinc project as the owner/operator of a facility for the treatment of zinc bearing secondary feeds. This project is due for start up in the first quarter of 2008.

Jan 1, 2008

By John Russell

"Faster, safer, grinding mill relining offers the obvious attractions of reduced mill relining times with the knock-on incentive to reduce all other maintenance down-time, opening the possibility for increased annual plant utilisation.Leading edge liner handler technologies by RME, focused toward even shorter relines for very large SAG and AG mills, have recently split into two quite distinct paths:•,?Single SAG/AG Mill Relining Machines (MRM’s) of very large capacity, such as Newcrest Cadia’s 40’ SAG MRM of 6000 kg capacity and P.T. Freeport’s 38’/34’ SAG MRM of 7250 kg capacity;•,?Twin-machine SAG/AG Mill Relining Systems of moderate to large capacity such as BHP Billiton’s Escondida Laguna Seca 38’ SAG MRM’s, each featuring 4500 kg capacity.RME, its customers noted above and their liner suppliers are providing leadership in this important annual utilisation advance.Once the 24 hour mill shell reline becomes reality, liners designed for maximum profit, not maximum life, albeit exchanged more frequently, become possible too.INTRODUCTIONAt most mineral grinding plants, mill relining activities dictate each maintenance shutdown’s critical path. When annualized, mill relining remains the largest, single influence in defining plant availability.Because of restricted access, both inside and outside the mill, increased application of manual labour has no effect on reducing relining downtime. The only answer for RME has been to develop and apply new relining technologies now known as RME’s Mill Relining System.RME’s primary focus for over twenty years has been the reduction of grinding mill relining times while simultaneously providing a marked improvement in relining safety. Our original (1990) target was to halve traditional (pre-RME) reline times and to eliminate accidents and injury by mechanizing all physical work."

Jan 1, 2008

By K. G. Thorne, M. J. McLeod, D. Hoy

"Throughout the Paleozoic, a variety of gold depositional environments were created in the New Brunswick segment of the northern Appalachians because of the complexity of arc and continental plate collisions and subsequent erosion of the orogen. In southwestern New Brunswick, recent exploration and research has focused on deposits and occurrences that can be broadly classified as intrusion-related, generated by late- to post-orogenic felsic to intermediate plutonic rocks emplaced during the Early to Middle Devonian. This work has led to the establishment of models for gold mineralization and guidelines for exploration in this area, which might also be applicable elsewhere in the southern part of the province and, perhaps, throughout the northern Appalachians. The deposits in the vicinity of Clarence Stream in southwestern New Brunswick exemplify this deposit type, and highlight the emergence of a possible major gold district in the region. Durant le Paléozoïque, une grande variété d’environnements aurifères ont été créés dans le segment néo-brunswickois des Appalaches du nord en raison de la complexité des collisions entre arcs et plaques continentales ainsi que durant l’érosion subséquente de l’orogène. Dans le sud-ouest du Nouveau Brunswick, les travaux d’exploration et de recherche récents se sont tournés vers les gisements et les indices appartenant à la classe des gîtes associés aux intrusions, générés par des roches plutoniques felsiques à intermédiaires tardi- à post-orogéniques mises en place au Dévonien précoce à moyen. Ces travaux ont permis d’établir des modèles de mise en place pour la minéralisation aurifère ainsi que des guides d’exploration pour ce secteur, lesquels pourraient aussi être appliqués ailleurs dans le sud de la province et, possiblement, dans l’ensemble des Appalaches du nord. Les gîtes aux environs de Clarence Stream dans le sud-ouest du Nouveau Brunswick sont un exemple de ce type de gisement, mettant en valeur ce qui pourrait devenir un district aurifère majeur dans la région."

Jan 1, 2008

By E. Marcoux, F. Lotfi, A. Belkabir, L. Maacha, A. C. Brown, S. Brunet

"Koudiat Aïcha is a small Zn-Pb-Cu deposit, enclosed in the Visean Sarhlef volcano-sedimentary series of the Moroccan Hercynian Jebilet massif. Base metal mineralization is located between a basal unit consisting of black argillite with arenite intercalations, and an upper unit composed of black argillite with locally fossiliferous calcareous units towards the top. Paraconcordant gabbro sills are present in both the upper and basal units, and the enclosing strata. Three successive phases of deformation linked to regional deformation overprint the volcano-sedimentary rocks and gabbros, as well as the sulfide mineralization.The mineral deposit includes several lenses of massive to semimassive pyrrhotite, 1 to 20 m thick, with a large halo of disseminated sulfide veinlets and sulfide nodules within a zone of intense chlorite alteration in the footwall. The ore mineralogy consists of massive to semimassive pyrrhotite with lesser amounts of sphalerite, chalcopyrite, arsenopyrite, galena, pyrite, and stannite.Lead isotope results (206Pb/204Pb averaging 18.27) suggest that the metals of the Koudiat Aïcha deposit are derived from the volcano-sedimentary host rocks. Sulfur isotopes also indicate a volcano-sedimentary origin, with bacterial reduction of sulfate (d34SCDT = -7.5‰ to -10.5‰). The conditions for sulfide meta-morphic equilibration range from 250° to 330°C (sphalerite and chlorite geothermometers). The gabbroic sills could have been a local heat source for hydrothermal circulation. Based on these geological and mineralogical features, a Besshi-type model seems appropriate for the genesis of the Koudiat Aïcha mineralization.Koudiat Aïcha est un petit dépôt de Zn-Pb-Cu, encaissé dans la série volcano-sédimentaire Viséenne de Sarhlef dans le massif Hercynien de Jebilet au Maroc. La minéralisation en métaux usuels se situe entre une unité basale d’argilite noire interlitée d’arénite et une unité supérieure composée d’argilite noire comprenant localement des calcaires fossilifères près de son sommet. Des sills de gabbro paraconcordants sont présent à la fois dans les unités basale et supérieure, ainsi que dans les strates environnantes. Trois phases de déformation successives associées a la déformation régionale superposent leurs effets sur les roches volcano-sédimentaires, les gabbros, ainsi que la minéralisation sulfurée. Ce gîte comprend plusieurs lentilles de pyrrhotite massive a semimassive de 1 a 20 m d’épaisseur au sein d’un large halo de veinules de sulfures disséminés et en nodules au sein d’une zone intensément chloritisée dans le mur du gisement. Le minerai consiste en pyrrhotite massive à semimassive avec des quantités subordonnées de sphalérite, de chalcopyrite, d’arsénopyrite, de galène, de pyrite, et de stannite. Les résultats de l’analyse des isotopes du plomb (206Pb/204Pb moyen de 18.27) suggèrent que les métaux du gîte Koudiat Aïcha proviennent des roches volcano-sédimentaires encaissantes. Les isotopes du souf¬fre indiquent eux-aussi une origine volcano-sédimentaire, impliquant la réduction bactérienne des sulfates (d34SCDT = -7.5‰ et -10.5‰). L’équilibration métamorphique des sulfures s’est produite entre 250° et 330°C (géothermomètres à sphalérite et chlorite). Les sills de gabbro pourraient avoir été la source de chaleur locale responsable de la circulation hydrothermale. Sur la base de ces caractéristiques géologiques et minéralogiques, il semble approprié d’invoquer un modèle de type pour Besshi pour expliquer la genèse de la minéralisation de Koudiat Aïcha."

Jan 1, 2008

By Y. Hayashi, A. Fuwa

To analyze zinc vaporization kinetics of zinc smelting slag in the ISP furnace, reduction reaction rate of zinc oxide from ZnO-FeOx-CaO-SiO2 slag system with CO-CO2-Ar gas mixtures has been measured by a therm o-gravim etric apparatus at various ZnO content, Pco, and temperature. The reduction rate was measured under a chemical reaction control in the initial three minutes where surface zinc content can be assumed constant. Through the reaction rate dependency analysis on ZnO contents, Pco and temperature, discussion has been made on its reaction mechanistic information in terms of rate coefficient, adsorption/desorption mechanism and activation energy.

Jan 1, 2008

By I. Kylmakorpi

In non-ferrous metal smelting, when the concentrate entering the furnace contains high levels of moisture, energy requirement for heating and drying increases and large volumes of exhaust are produced. To solve this problem, rotary dryers and flash dryers using direct heating, and also steam dryers using indirect heating have all been used for drying concentrate. The focus of this paper is to present the development and current applications of the Kumera Rotary steam dryer. The advantages of this technology are numerous, including reduced heating requirements, environmental friendliness, operation reliability and minimum maintenance needs; making it a top choice for drying concentrate.

Jan 1, 2008

By K. G. Thorne, D. R. Lentz, A. F. Park

"The Main zone of the Clarence Stream gold deposit is hosted by a shear zone adjacent to the Saint George batholith in southwestern New Brunswick. The mineralization history relates to progressive deformation in the shear zone and the intrusion of the Magaguadavic granodiorite.Of three phases of deformation that have affected the area (D1-D3), D1 is not observed in the Clarence Stream shear zone. Two suites of igneous rocks intrude the shear zone: post-D2, pre-D3 gabbro; and granitic dikes, which crosscut the gabbros. Granitic dikes show a diverse range of relationships to D3 features, from pre-syn-D3 mylonitic fabrics in transposed and highly deformed enclaves, to nondeformed and entirely discordant dikes (post-D3).A variety of veins occur within this shear zone. Zoisite-bearing and later, crosscutting epidote-bearing veins are preserved as relics in quartz-mylonites, and predate quartz veins that host gold mineralization. The epidote-bearing veins are associated with pseudotachylitic cataclasite dikes, consistent with transient brittle failure during ductile deformation.Deformation relates to right-lateral strike-slip motion across the shear zone, and subhorizontal and near-vertical stretching lineations imply transpression. A late (late- or post-D3) dip-slip phase of motion is also apparent, and cooling followed a metamorphic peak early in D2-D3 history. Deformation of the shear zone, and more localized transient brittle failure, provided the permeability for fluid movement and vein emplacement. This scenario is similar to the findings of other studies, in which geochemical, tracer isotopic, and age-dating (U/Pb, 40Ar/39Ar) results suggest that the adjacent Magaguadavic granodiorite provided heat and metals. La zone principale (Main zone) du gisement d’or de Clarence Stream est encaissée par une zone de cisaillement qui longe le batholite de Saint George dans le sud-ouest du Nouveau Brunswick. L’historique de la mise en place de la minéralisation accorde un rôle important à la déformation progressive dans la zone de cisaillement et à la mise en place de la granodiorite de Magaguadavic.Des trois phases de déformation à avoir affecté la région (D1-D3), les effets de D1 ne sont pas observés dans la zone de cisaillement de Clarence Stream. Deux suites de roches ignées se sont mises en place dans cette zone de cisaillement : un gabbro post D2, pré-D3 et des dykes granitiques qui recoupent le gabbro. Les dykes granitiques montrent une grande diversité de relations avec les structures D3, allant de précoces à synchrones aux fabriques mylonitiques D3 dans des enclaves transportées et fortement déformées à des dykes complètement discordants et non déformés (post-D3).On note diverses veines dans cette zone de cisaillement. Des veines contenant de la zoisite ainsi que des veines d’épidote sécantes plus tardives, lesquelles sont préservées comme reliquats dans les mylonites à quartz et sont plus vieilles que les veines de quartz contenant la minéralisation aurifère. Les veines d’épidote sont associées à des dykes de catacalasite à texture de pseudotachylite, compatibles avec une rupture cassante épisodique durant la déformation ductile.La déformation résulte d’un mouvement décrochant dextre le long de la zone de cisaillement et les linéations d’étirement subhorizontales et quasi-verticales impliquent de la transpression. Une phase tardive (tardi- ou post-D3) de mouvement selon le pendage est aussi apparente, et le refroidissement succède à un pic métamorphique tôt dans l’histoire D2-D3. La déformation de la zone de cisaillement et la rupture cassante épisodique ont fourni la perméabilité nécessaire au mouvement des fluides et à la mise en place des veines. Ce scénario est similaire à celui proposé par d’autres études, dans lesquelles les résultats de géochimie, de traceurs isotopiques et de géochronologie (U/Pb, 40Ar/39Ar) suggèrent que la granodiorite de Magaguadavic avoisinante a fourni la chaleur et les métaux."

Jan 1, 2008

By K. Sun, S. A. Argyropoulos

The assimilation and the exothermic behavior of Zn-Zr metallic powder compacts into molten aluminum was studied by measuring simultaneously the temperatures inside at the centerline of the compact, at its surface, and inside the molten aluminum bath, as well as the net downward force acting on the compact. In addition, the exothermic behavior of these compacts was also investigated in an argon protected atmosphere. The temperature rise inside the compact increases significantly with the mass ratio of zirconium in the compact and to a lesser degree with the aluminum bath temperature. Experimental results on the recovery of these compacts in molten aluminum will also be presented.

Jan 1, 2008

By S. Kelebek, E. Yalcin

"Two composite samples of a gold-bearing ore from North Western Quebec (Barry Township) were tested to assess their grindability, recovery by flotation and Knelson concentrator as well as extraction using cyanidation.Work index values (BWi) for two composites were found to be 10.4 and 11.0 kWh/tonne, respectively. Flotation tests involved feed samples for which the particle size ranged from a P80 value of 205 ?m to 53 ?m, which resulted in gold recoveries of 91.8% to 95.8% (at gold grades of 130 to 140 g/tonne). Cyanidation tests indicated gold extraction levels ranging from 94.2 to 97.5%. Higher, recoveries were obtained at finer grind sizes and higher cyanide strengths. However, the grind size had a bigger impact on gold leaching. Gold grade and recoveries obtained with the Knelson concentrator device were lower than those obtained by flotation. Mass recoveries to concentrate products strongly depended on the fluidization pressure used. High gold recoveries can be obtained generally at low water pressures of 3 to 4 psi. Higher water pressures produced more selectivity at the expense of higher gold losses.It can be concluded that the gold ore samples tested have good characteristics due to moderate levels of energy requirement, high gold recoveries and extraction rates attainable.INTRODUCTIONBench scale testing of ore samples is an important step in the long series of metallurgical and economic studies involved in bringing new ore bodies into production (Coleman, 1980). Through a laboratory testing program, the behaviour of an ore in a particular process on a larger scale can be established. In an exploratory manner, this testing can be helpful for classification of ores in terms of “good ore” or “problematic ore” by providing preliminary information on recoverability of target minerals. Potential problems if any can be assessed by further investigation of products (e.g., middlings) obtained as a result of testing. A detailed bench scale experimental program in the metallurgical laboratory can also provide the background work for flowsheet development. Depending on the simplicity or complexity of the ore to be tested and type of details required from a testing program, the amount of samples required in the mineral processing laboratory can vary from several kg to more than one hundred kg depending on how detailed the metallurgical testing program is."

Jan 1, 2008

By V. G. Papangelakis, J. E. Dutrizac, G. Azimi

A new model capable of predicting the solubility of calcium sulphate solid phases in zinc sulphate processing solutions from 25 to 95°C was developed. The model uses the Mixed Solvent Electrolyte (MSE) model of the OLI systems software to calculate the mean activity coefficients of the electrolyte species. The model was tested using recently developed experimental measurements. It was shown to predict accurately the solubility behaviour of calcium sulphate in multi-component zinc processing solutions containing ZnSO4, H2SO4, MgSO4, MnSO4, Fe2(SO4)3, Na2SO4 and (NH4)2SO4. The model can also explain the complex effect of coexisting metal sulphates on the solubility of the CaSO4 phases. The model is a practical tool for assessing the process chemistry of a wide variety of complex aqueous processing streams.

Jan 1, 2008

By Todd Smith, Brigitte Lacouture, Greg Anderson, David Lin

"The lead and zinc flotation circuits at Red Dog Mine are preceded by a preflotation circuit which recovers naturally-floating organic carbon contained in the ore. Organic carbon is a potential contaminant in the lead concentrate and is detrimental to lead-zinc selectivity. Prior to 2007, the Red Dog preflotation circuit consisted of a single stage bank of tank cells which floated the organic carbon. The preflotation concentrate was discarded directly to tailings, however, this stream contained significant amounts of lead and zinc. Zinc loss to preflotation ranged from 2% to 6%, relative to the zinc in the mill feed and was proportional to the amount of organic carbon in the ore. The main mechanism of the zinc loss was entrainment.Pilot plant and modeling testwork were conducted to examine the use of a Jameson Cell to clean the preflotation concentrate. Results indicated that up to 90% of the zinc deporting to preflotation concentrate could be returned to the flotation circuit for recovery. The installation of a 5.4 m Ø Jameson Cell with 18 downcomers was initiated in June 2006. The new preflotation cleaning circuit was commissioned in March 2007. Conservatively, preflotation cleaning has resulted in zinc and lead absolute recovery gains of 1.0% and 1.5%, respectively. The $9.1M project has a payback period of approximately 1 year at current metal prices.INTRODUCTIONRed Dog Preflotation CircuitRed Dog Mine is located above the Arctic Circle in northwest Alaska. It is the world’s largest zinc concentrate producer with a production rate of more than 1.0M t/yr. Red Dog is operated by Teck Cominco Alaska Incorporated under an operating agreement with the Northwest Alaska Native Association (NANA). Due to the remote location of the mine, it is accessible only by air, or seasonally, by ocean-going barges.The Red Dog deposit is a rich sedimentary exhalative (sedex) zinc-lead-silver deposit. The major sulphides, in decreasing order of abundance, are sphalerite, pyrite, galena and marcasite. Due to the complex nature of the ore body, run-of-mine ore is blended in stockpiles before being crushed and processed through the concentrator. The average mill feed grade for 2006 was 6.1% lead, 20.6% zinc, 8.0% iron and 0.67 % organic carbon."

Jan 1, 2008

By M. Abzalov

"Control of analytical data quality is usually referred to in the mining industry as Quality Assurance and Quality Control (QAQC), and involves the monitoring of sample quality and quantification of analytical accuracy and precision. QAQC procedures normally involve using sample duplicates and specially prepared standards whose grade is known. Numerous case studies indicate that reliable control of sample precision is achieved by using approximately 5% to 10% of field duplicates and 3% to 5% of pulp duplicates. These duplicate samples should be prepared and analyzed in the primary laboratory.Bias in the analytical results can be identified by inclusion of 3% to 5% of the standard in each sample batch. Several different standards are used, with values spanning the practical range of grades in the actual samples. A blank (a sample in which the concentration of metal of interest is below detection limit) should also be included. Standard samples alone cannot identify biases introduced during sample preparation, and therefore approximately 5% of the duplicate samples (coarse rejects and pulp) should be processed and assayed at another, external, reputable laboratory.This paper discusses techniques used for estimation of errors in precision and accuracy, and overviews diagnostic tools. It is shown that one of the most commonly used methods, the Thompson-Howarth technique, produces consistently lower results than other methods. These results reflect the nature of this method, which relies on the assumption of a normally distributed error, and thus produces biased results when errors have a skewed distribution. This study concurs with the suggestion of Stanley and Lawie (2007: Exploration and Mining Geology, v. 16, p. 265-274) to use the average coefficient of variation (CVAVR(%)) as the universal measure of relative precision error in mine geology applications: Le contrôle de la qualité des données analytiques est habituellement désigné sous l’appellation d’Assurance et Contrôle de la Qualité (ACQ), elle implique le suivi de la qualité des échan¬tillons et la quantification de la reproductibilité et la précision analytiques. Les procédures des pro¬grammes d’ACQ impliquent habituellement l’usage de duplicata et de standards analytiques dont la teneur est connue. Plusieurs études de cas indiquent qu’une bonne fiabilité du contrôle de la précision des échantillons est atteinte par l’usage de 5% à 10% de doublons sur le terrain et de 3% à 5% de doublons de pulpe. Ces duplicata devraient être préparés et analysés au laboratoire principal.Un biais des résultats analytiques peut être identifié par l’inclusion de 3% à 5% d’échantillons standard dans chaque envoi d’échantillons. Plusieurs standards sont utilisés, avec des valeurs couvrant l’étendue des teneurs habituellement rencontrées dans des échantillons réels. Un blanc (un échantillon dans lequel la concentration d’un métal donné est sous la limite de détection) devrait aussi être inclus. L’emploi exclusif d’échantillons standards ne permet pas l’identification de biais résultant de la préparation des échantillons, de telle sorte qu’environ 5% des duplicata (rejets grossiers et pulpes) devrait être traités a un autre laboratoire indépendant et fiable.Cet article passe en revue les techniques utilisées pour évaluer l’erreur liée à la précision et a la reproductibilité, et effectue aussi un survol de divers outils diagnostiques. Il ressort de cet examen qu’une des techniques les plus fréquemment utilisées, la méthode Thompson-Howarth, fournit des estimés systémati¬quement inférieurs à ceux provenant des autres méthodes. Ces résultats sont un reflet de la nature de cette méthode, laquelle assume une distribution normale de l’erreur, biaisant ainsi les résultats lorsque l’erreur présente une distribution asymétrique. La présente étude recommande de privilégier l’usage du coefficient moyen de variation (CVAVR(%)) en tant que mesure universelle de la précision relative de l’erreu"

Jan 1, 2008

By Augustine O. Orumwense, Micheline Boisclair

"The use of stirred mill to complement tumbling mills in grinding fine grained minerals is increasingly becoming an attractive processing option. Parameters such as agitation speed, grinding media type and size, feed pulp density, and grinding time were studied in order to elucidate their impact on stirred milling. Test results showed that the parameters have a profound effect on stirred mill efficiency and operating cost. A comparative test with a tumbling ball mill was also made and the specific energies of both mills in fine grinding were analyzed. A difference of over 40% in energy savings particularly when the product size is smaller than 20 µm was obtained with the stirred mill.INTRODUCTIONIn industrial processes where very fine and ultrafine particles are required such as in chemical, ink, food, paint and lacquer, pulp and paper, plastics, pharmaceutical, metallurgical and ceramic industries, the use of stirred mills for grinding is well established. Mineral processing plants are gradually shifting focus to the use of stirred mills for fine grinding and /or regrinding purposes as the target liberation size gets very small. A number of plants processing finely/sparsely disseminated ores are known to have adopted stirred milling technology for their fine grinding needs (Enderle et al., 1997; Harbort et al., 1999; Gao et al., 2000; Davey, 2003 & 2006; Pease et al., 2006).There are different kinds/designs of stirred mills available on the market but, all can be divided into two sub groups namely fluidized and non-fluidized types. The non-fluidized stirred mills consist of Tower mill, Vertimill, Sala agitated mill (SAM), and ANI-Metprotech (SVM). These mills are characterized by their low-speed and the use of fairly coarse grinding media size, 3 – 20 mm. Hence, they are mostly suitable for relatively coarse grinding application. The fluidized type includes the Isamill, Netzsch mill and Stirred mill detritor (SMD). These mills have a characteristic high agitator speed, use fine grinding media size of 0.5 – 5 mm, and are employed in very fine grinding operations. The superior fine grinding capability of stirred mills is attributable to two main process parameters, which are the use of fine grinding media and a high mill speed."

Jan 1, 2008