Search Documents

By W. W. Muir

"The Baker Mine used a 100-ton per day conventional cyanide leach mill located in northern British Columbia. A production decision was made in early 1980 and the mill was on fine in April 1981.Ore reserves had been estimated at 100,000 Ions averaging 0.9 oz gold per ton and 18 oz silver per ton . Mineralization consists of electrum (Au/Ag) and acanthite (Ag2S).This paper will review plant design and focus on some problems associated with start-up and early operation with the intention of assisting other mine operators by indicating potential problem areas.IntroductionThis paper will discuss operating strategies employed at Baker which improved over-all mill performance. Also included are some ideas which could be steps toward a more efficient operation in a similar setting.Actual dore production by mine life was 37,606 oz gold and 742,117 oz silver.Figure 1 illustrates the relative stability attained over the mine life. Metal recoveries for gold and silver were 92% and 85% respectively.Safety at Baker was of prime importance because of its remote location. Baker received the Mine Safety Association ""Small Mines Award "" in two of its three operating years. At shutdown in late 1983 the mill had operated for over 850 days without a lost-time accident."

Jan 1, 1985

By J. M. Paxton, R. L. Roscoe, G. A. McCreary, W. W. Muir, T. J. Drown, D. A. Barr, T. W. Law

"This paper reviews the complete cycle of a small mining operation in a remote section of northern British Columbia, including discovery, exploration, development and production. The discovery of high-grade epithermal gold-silver mineralization occurred in 1969 following a regional geochemical reconnaissance program designed to search for porphyry copper mineralization in the Cassiar-Omineca Mountains. Exploration and development from 1971 to 1979 included geological, geochemical and geophysical surveys; trenching, almost 30 000 feet of surface and underground drilling in about 100 holes and cross-cutting, drifting and raising on the principal goldsilver- bearing vein. This led to the delineation of 100000 tons at an estimated grade of0.9 oz gold per ton and 18 oz silver per [on to an average depth of 120 feet below surface. of a 100-ton per day mining operation employing about 50 personnel with all supporting infrastructure transported to the site by a Hercules aircraft. The operation was subsequently supported by its own Twin Otter aircraft with periodic Hercules campaigns supplying major items including fuel.The mining operation included both open-pit and cut-and-fill methods. The milling operation employed conventional cyanide leach process with cyanide destruction initially by alkali chlorination and subsequently by the Inco SOl /Air process.The fly-in operation, initially structured on a 21-day-in and 7-day-out basis was modified to al-t-day-in and Z-day-out basis with no loss in efficiency and with a significant increase in employee satisfaction. The operation, which earned the B.C. Small Mines Safety A ward in two consecutive years in its Ll-month operating history, emphasized safety and process hazard awareness. Wildlife studies in the environmentally sensitive mine area also showed that industry and wildlife can coexist in harmony.Most importantly, the paper compares the feasibility assumptions with actual operating experience."

Jan 1, 1986

By R. A. Price

The base of the biozone of Olenellus is accepted as the most universally applicable criterion for defining the base of the Cambrian System. The use of this definitive criterion is restricted by important practical considerations. In the southeastern Canadian Cordillera this zone appears to truncate the basal ortho-quartzite of a west to east marine -transgression. This transgression began in Interior British Columbia in the Late Proterozoic and terminated in the region of the present Rockies in the Late Waucobian. Most of the material deposited by the transgressing sea originated in the eastern positive element 'Laurentia' and was transported over the intervening low Proterozoic-Windermere erosion surface. The configuration of the advancing shoreline and the distribution of the sediments were controlled by the tectonic activity of positive elements in northwestern Montana (Montania) and in the Fairmont Hot Springs-Radium area of British Columbia.

Jan 1, 1956

Introduction A Hypothetical Scenario: Suppose that your company's research department has developed a new device which represents a significant innovation. You would like to begin selling it as soon as possible. The new device has not been publicly disclosed. You're not sure about what type of intellectual property protection you should be seeking, or when you should be seeking it. As discussed below, assuming that the costs are worth it, a patent application probably should be filed before any public disclosure is made. In general, if you do not file a patent application prior to a public disclosure, you will lose rights. Major Types of Intellectual Property In this paper, intellectual property protection is broadly discussed. Practical steps which can be taken to minimize the possibility of losing intellectual property rights (and maximizing the possibility of benefiting from your company's intellectual property) are outlined at the end of this paper. The issues discussed in this paper are somewhat complex, because a number of outcomes are possible, depending on the facts. It is strongly recommended that you seek legal advice in your jurisdiction in connection with any particular circumstances relating to intellectual property rights. "Intellectual property" refers to a number of different types of rights. The major types of intellectual property are: (i) patents; (ii) trademarks; and (iii) copyright. Trade secrets are also usually considered to be a type of intellectual property, and they are also discussed in this paper because of their importance. In general, each of these types of intellectual property protects different subject matter, although there can be some overlap. Intellectual property rights are generally territorial in nature. The scope of protection of a type of intellectual property in a country (e.g., patent protection) depends on whether the specific national requirements for protection have been met.

Feb 1, 2008

By Robert Drummond

Away back in the eighties of the last century, when Sir Charles, then Doctor, Tupper, was not only a prominent but a dominant figure in the political life of Nova Scotia, his opponents brought the railing accusation against him that he was the foremost of egotists because of his frequent use of the personal pronoun. I heard Tupper speak and had no sympathy with the railers, because I could not well see how the pronoun could be dispensed with without laying himself open to a charge of affectation. I shall make reference in what follows to incidents in which I have taken part, and shall be at no pains to dispense with the pronoun, even though thereby I lay my-self open to the charge of being a pupil of the deceased states-man. EVENTS LEADING UP TO THE ORGANIZATION OF THE PROVINCIAL WORKMEN'S ASSOCIATION The Springhill Mining Company began development work at Springhill in the early seventies of last century. So vigorously was the work prosecuted that in 18 7 4 two slopes, the east and the west, were in active operation, with a considerable. output, the east slope on occasional days producing 800 tons. The President of the Company, the late Senator McFarlane, was a Nova Scotian, the other directors were mainly merchants from St. John, N.B. From the first the enterprise was an .astonishing success, due in the greatest part to its geographical position, and in large part to the untiring vigilance of the directors, a majority of whom visited the collieries at short intervals, thereby keeping the manager, much of the time, on tenter hooks.

Jan 1, 1924

By R. T. Seaman

There are several hydrometallurgical alternative processing options under development for high enargite and arsenic containing copper concentrates ranging from biological, atmospheric, medium temperature oxidation to total oxidative leaching. The most developed of these options is the CESL process boasting pilot campaigns totaling more than 8760 hours of fully integrated continuous operation, as well as, over two thousand batch scale oxidation tests performed on dozens of concentrates for flowsheet development. This paper reports the observed deportment of arsenic under varying arsenic, iron and acid oxidation conditions; it also describes the impact of iron to arsenic ratios and residue recycle on overall arsenic behavior and its stability in residue. INTRODUCTION The CESL Hydrometallurgical Process (CESL) was originally developed to compete with smelting of clean chalcopyrite concentrates. High Treatment Charges and Refining Charges (TC/RCs) combined with premiums on London Metal Exchange (LME) grade copper from onsite refining made treatment of copper concentrates using CESL a viable option at the time. As world demand for copper increased and a subsidized Chinese refining market developed, smelting contracts became more favourable for the miner and focus was placed on modifying the CESL Hydrometallurgical Process to handle concentrates with elevated deleterious elements. Dozens of pilot campaigns processing concentrates containing elevated concentrations of uranium, fluoride, mercury and nickel all led to further developments of the CESL Hydrometallurgical Process. In 2016 a United States patent was granted for a novel modification of the CESL Hydrometallurgical Process for recovery of copper from arsenic-bearing and/or antimony-bearing copper sulphide concentrates, Henry Salomon de Friedberg (2016). To date, over 2000 bench scale tests along with five fully integrated closed loop pilot campaigns, totaling over a year of online operation time, have been conducted processing arsenic bearing copper concentrates. This paper summarizes the observed behavior of arsenic under varying autoclave and process conditions.

Jan 1, 2019

By H. Tan

The effect of carbonaceous matter on gold extraction was investigated in cyanide systems with pure gold as well as pre-robbing sulfide gold ores. Auger studies demonstrated that the carbonaceous matter preferentially smeared on iron sulfide rather than aluminosilicate surfaces during wet or dry grinding. During mechanically mixed leaching, coating of sulfides and silicates and stripping of carbonaceous matter occurred simultaneously. TEM and XPS studies indicated preferential coating in the form of elemental (graphitic) carbon at the edges and the defect sites of particles. Interestingly, carbonaceous matter extracted from the gold ore was predominantly graphite and not preg-robbing in a solution with a high KCN concentration. However, the carbonaceous coating had a significantly detrimental effect on gold dissolution when gold was pre-ground with the gold ore. Artificial coating on gold surfaces with the natural carbonaceous matter from the ore was also found to substantially retard gold dissolution. With the addition of the natural carbonaceous matter from the gold ore, gold extraction from two non preg-robbing sulfide gold ores was inhibited owing to carbonaceous coating. The presence of carbonaceous matter significantly reduced the current density for gold oxidation and increased the current density for pyrite oxidation. This could explain the fact that carbonaceous coating hindered gold dissolution while enhanced sulfide preg-robbing.

Jan 1, 2005

By M. Fujikawa

The Kamioka Zinc Smelter was converted from the jarosite process to the goethite process in the year 2000. The reasons for the conversion of the process were that the silica content of the raw material increased and the iron content decreased. The silica easily turns to a gel in sulfuric acid solutions and this causes the solid-liquid separation characteristics to deteriorate. The basic behavior of silica in sulfuric acid solution was investigated and it was found that the goethite process is the most suitable to effectively separate and remove silica from solution. Furthermore, Fe has the capability to remove elements such as Ge that have an adverse effect on zinc electrolysis. This means that, when the Fe content of the raw material decreased, the impurity removal capability also decreased and there was a risk of a build-up of impurities in the process. Iron precipitates in many forms in sulfuric acid solutions. The capability to remove elements such as Ge differs depending on the compound precipitated. Goethite has a higher capability than jarosite to remove elements such as Ge. In this report, the results of applying the process established by investigations of the basic behavior of Fe, silica and Ge in the zinc refining plant are presented.

Jan 1, 2006

By N. Gharib, F. Hassani, P. Nekoovaght

"Novel rock breakage techniques are becoming more viable and attractive to industry. Microwave energy, as a thermal energy capable of inducing micro cracks through differential heating (therefore expansion) is a technology gaining considerable attention in mineral processing and ore comminution applications. Recently, the use of microwave radiation has been evaluated as a possible avenue for terrestrial and extra-terrestrial drilling applications as well as full face tunneling or rock breaking machines. As part of an overall research on use of microwave in rock breaking systems, the influence of microwave energy on the mechanical properties of common hard rock types as basalt has been investigated. The results revealed that microwave energy irradiation imposes micro and macro cracks to the surface of the rock being irradiated. In explosive free tunneling applications using TBM, jointed and cracked surface of rock eases the cutting process and increases penetration rate. The experimental setups have been simulated with the help of a multi-physics numerical modeling and the results have been compared with practical experiment. The wave propagation of microwave has been simulated and the distances where the power intensity is higher are identified. Experimental and simulation results underlined the potential impact of the use of microwave energy in underground or surface excavation applications such as mining and tunneling. This will also contribute economically when mine-to-mill operation is fully considered to improve the efficiency of rock crusher stages. INTRODUCTIONDuring hard rock breakage (i.e., separation of a piece of a rock from its parent deposit) in mining and civil applications, the performance of mechanical equipment such as tunnel boring machines (TBMs) is limited by high levels of bit wear and maintenance. Preweakening natural rock prior to breaking it by machine is one approach to lower bit wear and maintenance costs. Some preweakening methods apply heat directly or indirectly. For example, flame torch-assisted TBMs (Lauriello et al., 1974; Resource Technology, 1984) have been deemed economical in terms of equipment, but their feasibility is limited by high fuel consumption. Microwave energy could offer several advantages over the flame torch method: it does not produce emissions or increase fuel consumption (electricity source is available on the machine), and is easy to control (quick power on and off)."

Jan 1, 2015

By J. E. Dutrizac, Alba Sunyer

The factors affecting the precipitation of arsenic-free alunite (KAl3(SO4)2(OH)6) were investigated in a series of laboratory experiments. Although the amount of alunite precipitated increased with increasing retention time, temperature, solution pH and the concentrations of Al(SO4)1.5 or K2SO4, the composition of the products remained nearly constant. The preferred conditions identified for the precipitation of arsenic-free alunite were then used to assess the behaviour As(III) and As(V) during alunite precipitation at 98°C. Increasing additions of As(III), as NaAsO2 or As2O3, resulted in a slight increase in the amount of precipitate formed at pH 2.80. However, X-ray diffraction analysis showed all the precipitates to be alunite, and <0.2% As(III) was detected in the products. In contrast, increasing additions of As(V), as KH2AsO4 or As2O5, resulted in significant increases in the amount of precipitate formed at pH 2.80 or 3.00. Furthermore, the arsenate (AsO43-) contents of the precipitates increased up to 15%, and the sulphate contents decreased, as the As(V) concentration of the synthesis solution increased from 0 to 9 g/L. X-ray diffraction analysis of the products detected only alunite, but there was a progressive expansion of the alunite cell with increasing arsenate content. The implication is that arsenate substitutes for sulphate in the alunite structure. Preliminary observations on the environmental stability of the arsenate-bearing alunite using the TCLP protocol gave solubilities <0.4 mg/L from a precipitate containing 8.5% AsO4 and 7.8 mg/L from a product containing 19.5% AsO4. Thus, it appears that alunites containing less than -10% AsO4 would be an acceptable vehicle for the disposal of arsenic from hydrometallurgical processing solutions.

Jan 1, 2011

By L. V. Volkov

The equilibrium of the CuO-Cu20-Cu+-Cu2+ system with various chloride ion concentrations in solution in the presence or absence of an oxidant was investigated. It is shown, that, regardless of the presence or absence of chloride ions or oxidant (oxygen) in the system, the process can be divided into three stages, which are characterized by differing rates and mechanisms of metallic copper cementation and cuprite precipitation and, hence, lead to differing rates of the dissolution of nickel into solution. The effect of the concentrations of chloride ion and oxidant on the phases in the process residues is also discussed. The addition of an oxidant increases the amount of cuprite (Cu20) in the leach residue. With increasing chloride ion concentrations, the rate of copper cementation increases, even without an oxidant in solution. The results of these laboratory experiments and the mechanisms developed are consistent with analysis of samples of industrial cement copper obtained from the Severonickel Combine.

Jan 1, 2007

By S. Banisi, J. Marois, A. R. Laplante

"This paper compares the behaviour of gold and ore in the grinding circuit of Hemlo Mines Ltd. Particular attention is given to grinding kinetics, classification behaviour, and liberation. For grinding kinetics, laboratory grinding of gold flakes and silica, 840 µm to 1200 µm in size (14/20 mesh), was also performed to provide a standard for comparison and to study in a controlled environment the mechanisms of breakage, folding , smearing and impacting.Grinding kinetics were characterized at laboratory scale with breakage and selection functions. The breakage function showed that 75% of gold disappearing from the 840 µm to 1200 µm class reported to the 600 µm to 840 µm; this figure is much higher than for silica (46%) or most other minerals, and implies that comparatively fewer fine fragments are produced from the breakage of gold flakes, on account of gold&apos;s malleability. The selection function of silica was four times that of gold. At plant scale, the ratio of the selection function of ore and gold increased from 6 for at 50 urn to JOO pm to 20 at 500 um to 1000µm.Observation of original flakes and their fragments with the scanning electron microscope showed that the main mechanism of ""grinding"" from the 840 µm to 1200 µm to the 600 µm to 840 µm class was folding rather than actual breakage. This was confirmed by a measure of individual flake weight. The postulated breakage cycle is that relatively globular flakes become increasingly serrated through grinding; they can then regain their original shape through folding and reflattening into cylindrical and spherical shapes, as the majority does; however, some fragments will at this point undergo actual breakage. Photograhic evidence is presented to support the proposed mechanisms.Smearing of gold unto silica was observed when silica was ground after a gold, and embedding of silica into gold flakes when gold was ground after a silica. Both mechanisms occur whenever gold and harder minerals are jointly ground, and result in ""unliberation"" of gold. It is postulated that smearing of gold onto other minerals plays an important role in explaining how gravity recovery can increase over-all gold metallurgy, especially when used ahead of flotation.Classification of gold in the primary hydro cyclones takes place at a much finer cut-size than ore, 20 µm vs 57 µm. This and the slower grinding kinetics result in high gold circulating loads in the primary loop, 6700%, and a gold content in the primary cyclone underflow (PCUF) is twenty-four times that of the ore. The gold size distribution for primary cyclone overflow is much finer than that of the ore, although they are essentially similar in the PCUF.Liberation, or more accurately ""gravity recoverability"", was assessed with a 7.5 cm (3 in.) Knelson concentrator. It varied between the thirties for the primary mill discharge and two cyclone overflows, to highs of 89% and 92% for the PCUF and secondary mill discharge."

Jan 1, 1991

By S. Banisi, J. Marois, A. R. Laplante

"This paper compares the behaviour of gold and ore in the grinding circuit of Hemlo Gold Ltd. Particular attention is given to grinding kinetics, classification behaviour, and liberation. For grinding kinetics, laboratory grinding of gold flakes and silica, 840-1200 um in size (14/20 mesh), was also performed to provide a standard for comparison and to study in a controlled environment the mechanisms of breakage, folding, smearing and impacting.Grinding kinetics were characterized at laboratory scale with breakage and selection functions. The breakage function showed that 75% of gold disappearing from the 840-1200 um class reported to the 600-840 um; this figure is much higher than for silica ( 46%) or most other minerals, and implies that comparatively fewer fine fragments are produced from the breakage of gold flakes, on account of gold's malleability. The selection function of silica was four times that of gold. At plant scale, the ratio of the selection function of ore and gold increased from 6 for at 50-100 um to 20 at 500-1000 um.Observation of original flakes and their fragments with the scanning electron microscope showed that the main mechanism of ""grinding"" from the 840-1200 um to the 600-840 um class was folding rather than actual breakage. This was confirmed by a measure of individual flake weight. The postulated breakage cycle is that relatively globular flakes become increasingly serrated through grinding; they can then regain their original shape through folding and reflattening into cylindrical and spherical shapes, as the majority does; however, some fragments will at this point undergo actual breakage. Photographic evidence is presented to support the proposed mechanisms.Smearing of gold unto silica was observed when silica was ground after a gold, and embedding of silica into gold flakes when gold was ground after a silica. Both mechanisms occur whenever gold and harder minerals are jointly ground, and result in ""unliberation"" of gold. It is postulated that smearing of gold onto other minerals plays an important role in explaining how gravity recovery can increase overall gold metallurgy, especially when used ahead of flotation.Classification of gold in the primary hydrocyclones takes place at a much finer cut-size than ore, 20 vs. 57 um. This and the slower grinding kinetics result in high gold circulating loads in the primary loop, 6700%, and a gold content in the primary cyclone underflow (PCUF) is twenty four times that of the ore. The gold size distribution for primary cyclone overflow is much finer than that of the ore, although they are essentially similar in the PCUF.Liberation, or more accurately ""gravity recoverability"", was assessed with a 7.5 cm (3"") Knelson concentrator. It varied between the thirties for the primary mill discharge and two cyclone overflows, to highs of 89 to 92% for the PCUF and secondary mill discharge, 89 and 92%, respectfully."

Jan 1, 1991

By C. E. Ells

Current knowledge of the behaviour of inert gases in metals is reviewed, with particular emphasis given to the phenomenon of the growth of gas-filled bubbles.

Jan 1, 1960

By Takao Oishi, Go Ohara, Toru Kitazaki, Masahiro Tanaka

"The High Pressure Acid Leach (HPAL) plant for nickel-cobalt mixed sulphide production at Coral Bay Nickel Corporation (CBNC) in the Philippines has been in operation since 2005 with a capacity of 10,000 t/year of nickel. Subsequent to the commissioning of the second plant in 2008, the production capacity increased to 22,000 t/year of nickel (Llerin et al., 2011). CBNC’s annual nickel production reached more than 24,000 tons of nickel in 2014. The concepts to achieve this capacity are the high availability and the reciprocally flexible operation of both plants. The availability depends on some factors, such as the control of impurities in the process and the equipment condition, to mention a few. In the HPAL process, it is not only the autoclave operating conditions that affect nickel extraction but also the impurities in the ore greatly influence it. The major element in the ore is iron and most of this iron is precipitated as Fe2O3, while the rest remains as Fe2+ or Fe3+ sulphate in solution. These ions in solution reduce the availability, so it is important to control the formation of iron ions by controlling the impurities in feed ore as well as the HPAL conditions. This paper presents the general HPAL process and the behaviour of impurities, focusing on iron behaviour in the HPAL process.INTRODUCTIONCoral Bay Nickel Corporation ProfileCoral Bay Nickel Corporation (CBNC) was founded on April 2002, as a joint venture of four companies; namely, Mitsui Corporation (18%), Sojitz Corporation (18%), Nickel Asia Corporation (10%) and Sumitomo Metal Mining Corporation (SMM) with a controlling stake of 54%. Aside from its capital share, Nickel Asia Corporation also supplies the ore and limestone for the High Pressure Acid Leach (HPAL) plant located in Rio Tuba, Philippines, as shown in Figure 1 (Tsuchida, 2008). The objective of the CBNC project is to produce 22,000 t/year (original design) of nickel and 1,500 t/year of cobalt, as sulphide, by the treatment of nickel laterite ore which is a low grade nickel oxide ore in the Philippines (Mines and Geosciences Bureau, 2014). The sulphide product has been exported as a raw material to the SMM Nickel Refinery in Japan for 30 years. The product of this plant, a mixed (Ni/Co) sulphide, is shipped to the SMM’s Nickel Refinery in Niihama, Japan. SMM Corporation provides the technology and management personnel to the plant. SMM Corporation also supplies the sulphuric acid, which is the main reagent for the HPAL process."

Jan 1, 2016

By J. E. Dutrizac, J. M. Zinck

Ferrihydrite is often the initial precipitate resulting from the rapid neutralization of Fe(III) sulphate solutions, and it seems to be a major constituent of zinc plant neutral leach residues. The most important parameters affecting ferrihydrite precipitaton are temperature, solution pH and the neutralization rate. Low temperatures and rapid neutralization rates yield poorly filterable ferrihydrite, whereas higher temperatures and slower neutralization rates produce readily filterable precipitates; in all instances, however, the precipitates are two-line ferrihydrite. Significant amounts of Zn are incorporated in the ferrihydrite precipitates, and the Zn contents increase with increasing Zn concentration, pH or temperature. Generally, the sulphate contents of the precipitates decrease as the Zn contents increase, and this may indicate that the Zn is adsorbed on the ferrihydrite. Discrete Zn phases were not detected. Neither Cd nor Tl is precipitated with ferrihydrite, although thallium jarosite co-precipitates with ferrihydrite at high Tl concentrations and elevated temperatures. Virtually all of the Sn added to the solution precipitates with the ferrihydrite, but the tin is believed to be present as intimately admixed amorphous SnO2.nH2O. Although selenite extensively precipitates with the ferrihydrite, selenate remains mostly in solution, likely because of the close similarity of the SeO4 2- ion to the SO4 2- ion which is present in high concentrations and saturates the available sites for anion adsorption.

Jan 1, 1998

By I. E. Puddington, F. W. Meadus

The beneficiation of barite in mill tailings using an agglomeration technique has been demonstrated. Barite was selectively absorbed from a conditioned aqueous slurry into a collector oil by mechanically mixing slurry and oil. The resulting oil-bonded barite-containing agglomerate was washed, to remove gangue material, and further mechanically contacted with dilute H2SO4 This treatment resulted in the transfer of barite into the aqueous phase. Grades as high as '97% BaSO4, with recoveries of 80%, have been obtained using this technique.

Jan 1, 1973

By P. R. A. Andrews

"Garnet occurs in schists and gneisses in all provinces of Canada, all mainly in Quebec and Ontario. There is currently a renewed interest in exploration for economic sources of garnet for abrasive applications because of the inherent dangers from exposure to ground silica from sandblasting operations.High-quality garnet is used for lapping and grinding of glass and ceramics; for coated and bonded products such as sandpaper and cloth; and abrasive wheels for grinding and finishing various metals, woods, rubber and plastics. Low-quality garnet is used for cleaning and conditioning aluminum and other soft mewls, particularly by aircraft manufactures. Garnet may be added to grouting cements for oil-well drilling applications, and it has also been used for low- to medium-level radiation shielding. Garnet has been studied extensively by CANMET and its predecessor, Mines Branch, between 1917 and 1990. Twenty-nine studies relating 10 various aspects of beneficiation are presented and a review of the more important studies is presented. The information includes mineralogy, beneficiation methods, product sizes and analyses."

Jan 1, 1995

By P. R. A. Andrews

"Graphite is one of the most versatile of non-metallic minerals because of its diversified properties, for example: it is unctuous; it marks readily; burns slowly; is almost chemically inert; is flexible over a large temperature range; is a good conductor of heat and electricity; is hydrophobic; has a negative temperature coefficient of resistivity; has excellent weathering properties; tends to emulsify with water-in-oil; is readily soluble in iron; and after oxidative treatment, can exfoliate like vermiculite. These properties give rise to its major uses in lubrication, refractories, marking instruments, electrical products and paints.Flake graphite is the variety which commonly occurs in Canada; the provinces of Ontario and Quebec contain the deposits of economic significance, although graphite occurs in other provinces. The beneficiation of graphite has been the subject of many investigations at CANMET, thus reflecting graphite &apos;s importance as an industrial mineral. Thirty-eight studies relating to various aspects of beneficiation were conducted between 1918and 1989anda review of some of the more important studies is presented. The information includes mineralogy, beneficiation methods and results; flotation parameters and reagent concentration data are presented in tabular form. By so arranging the principal data, the research worker and production metallurgist will be assisted in the evaluation of graphite ores from a variety of origins."

Jan 1, 1992

By P. R. A. Andrews

"The sillimanite group minerals, kyanite, sillimanite and andalusite are identified as alumino-silicate minerals with the common chemical composition AIP3.Si02&apos; so that each possesses similar physical properties. Kyanite is the most abundant mineral and mainly occurs in Quebec, Ontario and British Columbia; sillimanite occurs in Ontario and Manitoba; and andalusite in Nova Scotia. The main use for the sillimanite-group minerals is in refractory applications for the production of refractory bricks and shapes. In refractory applications, the main performance criterion is the relative percentage of mullite formed within the material during firing. This phase gives a greater degree of resistance to creep deformation and slag attack, and improves the ability of the refractory to withstand high temperatures under load. The beneficiation of refractory silicate minerals has been the subject of many investigations at CANMET, and the former Mines Branch. Eighteen kyanite, two sillimanite, and three andalusite evaluation studies were conducted between 1933 and 1987. A review of some of the more important studies is presented, which includes information concerning mineralogy, beneficiation methods and flotation data."

Jan 1, 1995