Search Documents

By B. S. Kim, Y. D. Kim, T. S. Kim, T. B. Kim, H. J. Chae

"The Nd-Fe-B scrap was placed in Fe crucible with pure Mg in an Ar atmosphere, and the scraps were melted using an induction heating method. The effects of experimental parameters such as melting temperature (range of 993K to 1073K) and holding time (15min-600min) on the ability of extraction were investigated. The microstructure and diffusion layers were analyzed by Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS), and the constituent phases were characterized using XRay Diffraction (XRD). Diffusion of Nd through the Nd-Fe-B scrap into liquid Mg was described, and the diffusion coefficient of Nd in liquid Mg was estimated.INTRODUCTIONNd-Fe-B magnets are usually produced either from comminuted melt-spun ribbons as bonded magnets or hot pressed bulk magnets, or by sintering in conjunction with prior green compaction in an applied magnetic field (Sagawa et al., 1984). These magnets have been widely used for various electromechanical and electronic devices such as voice coil motors (VCMs) and magnetic resonance imaging (MRI) (Samardzija et al., 2012; Matsuura et al., 2006). The production of the Nd-Fe-B magnets is increasing by about 20% per year because of their excellent magnetic properties. However, the expansion of Nd-Fe-B magnet market induced a concern for the scarcity of Nd at the aspect of natural resource. Therefore, the development of an effective recycling process for Nd-Fe-B magnet scraps is an extremely important issue from the viewpoint of resource and energy conservation. Several recycling processes for the Nd-Fe-B magnets have been proposed (Uda et al., 2002; Lyman et al., 1993]. It has been reported that the best separation of rare-earths from the Nd-Fe-B magnets is obtained by sulfuric acid dissolution followed by precipitation of recyclable rare-earth salts. However, this process can make a large amount of waste water including dangerous solutions. Recently, (Xu et al., 2000) have reported a technique to extract Nd from 18Nd-72.4Fe-0.9B-1.82Pr-5.3Dy (wt.%) magnet scrap by using liquid metal extraction (LME) processing. However, these techniques seemed to be difficult for application, because the scraps consist of an infinitesimal amount of other minor elements (Pr, Dy, Cu, Al and Tb), and these minor elements can make a new intermetallic compounds with Mg. Also, some oxides or the plated Ni metal can be preventable to reaction between solid-liquid (S/L) interfaces. For these reasons, the substantive reaction mechanism between Mg and Nd-Fe-B scrap is not clear. In this study, the simple composition of 33Nd-66Fe-1B (wt.%) magnet scraps were prepared using an induction melting process. The effects of the experimental parameter on the diffusion properties between Mg and scraps were investigated to determine whether these methods could be used in industrial application in a liquid metal extraction (LME) process."

Jan 1, 2012

By C. -K. Fang, T. H. Chuang

"Temperature effects on the erosion of the 6063 aluminum alloy were investigated. Erosion experiments were performed by sandblasting silicon carbide particles of 80 grit size. The target volume loss, and worn depths of the eroded material were investigated at different temperatures. It was found that the temperature had only a minor impact on the peak attack angle. The effect of temperature on erosion damage depended on the relative humidity (RH) of the environment. IntroductionThe synergy of wind and sand or dust may result in the erosion of materials. However, the severity of erosion damage in different areas and in different seasons might be varied, depending on environmental variables such as temperature and humidity. As a result, determining the effect of environmental variables on erosion damage is important in selecting or ranking materials for their suitable applications in diverse areas.The relationship between erosion wastage and temperature is governed by many factors including temperature dependent properties of the material (strength, ductility, toughness, and dynamic hardness, etc.), mechanical erosion characteristics, the rate of oxidation, and the mechanical properties of oxides. Although the effect of temperature on erosion has been studied for engineering materials (Smeltzer et al., 1970; Gat and Tabakoff, 1978; 1980; Levy et al., 1986; Levy and Man, 1986; Chinnadurai and Bahadur, 1995; Howard and Ball, 1997; Colclough and Yeomans, 1997; Suckling and Allen, 1997), published literature dealing with aluminum alloy is rather limited."

Jan 1, 2000

By S. Fahland, P. Vogel

"The Gorleben salt dome has been investigated since 1979 for its suitability as a repository for the disposal of high-level radioactive wastes. The geoscientific surface exploration was followed by underground exploration of the site beginning in 1983: underground excavation work included the sinking of two shafts from 1986 to 1994, the excavation of the infrastructure area and of drifts located in the first exploration area EB1 within the following years. The exploration was interrupted for ten years from 2000 to 2010 as part of a moratorium. After the expiry of the moratorium in March 2010, the geoscientific underground exploration at the Gorleben site was resumed. The investigations were interrupted again in autumn 2012 due to a political decision. The exploration programme included extensive geoscientific investigations: geological exploration, geophysical investigations, mining exploration and mining observation, laboratory tests, in-situ geotechnical measurements, geological modelling and numerical model calculations. To analyse and interpret the results of the in-situ measurements and mining observation geomechanical, thermal and thermo-mechanical model calculations were carried out. One of the main elements of the in-situ geotechnical investigations were high-resolution geothermal measurements performed in boreholes used for geological exploration and geotechnical tests.The geothermal measurements are used to evaluate several geotechnical findings, e. g. drift closure, rock deformation, stress change, and are completed by thermal model calculations to analyse and interpret the results of in-situ measurements and mining observation. The model calculations have been carried out using the special purpose JIFE code. To consider the whole exploration mine with the adjoining host rock as well as the successive excavation of drifts and boreholes in detail a three-dimensional finite-element model was developed. The model calculations are used to analyse the cooling-off of the surrounding rock of the drifts caused by ventilation. The cooling-off of the surrounding rock is an ongoing process affecting the results of further geotechnical measurements in the near field of the drifts. To predict a realistic time and space dependent distribution of the temperature field of the host rock within the exploration area which is influenced by ventilation thermal model calculations are necessary. Comparing the calculated temperature field with the in-situ determined rock mass temperature field within the exploration area EB 1 the results show a sufficient agreement. Furthermore there is very good correspondence, both qualitatively and quantitatively, between the experimental and the calculated findings regarding the temperature profiles including the effects of excavation and ventilation of the drifts."

Jan 1, 2015

By A. D. Misener, L. G. D. Thompson

"IntroductionIt was shown by work previously reported that reliable geothermal gradients representative of various regions of the earth's, surface could he obtained from extended surveys of the rock temperatures in operating mines. These surveys showed the presence of anomalies in the isothermal levels and the existence of regions of regular behaviour. Below about 3,000 feet the temperature gradients became quite regular over the areas stud1ed. It is these regular gradients which are taken as representative of the region, wherever possible.The present paper describes the extension of this work which was undertaken to obtain further temperature gradients with a view to correlating them to other geophysical properties determined for the same regions. The additional data obtained have indicated possible reasons for the temperature anomalies. The experimental procedure was similar to that already described and was again made possible through the wholehearted co-operation of the management and the assistance of the personnel of the mines concerned. The research was entirely supported by a grant from the Research Council of Ontario.The equipment was a distinct improvement over that previously used and made it possible to take many more accurate temperature readings in a given time. Thermistor resistance thermometers were used, encased in silver sheaths and protected against damage by heavy copper casings. These were calibrated with a standard platinum resistance thermometer.The bridge used with these thermometers was one of a number designed and built by the Meteorological Service and designated M.S.C. Thermometer Indicator Type C-3. This very convenient and portable instrument operated from batteries in the instrument case. Multiple thermometer connections were provided so that rapid readings• of a number of thermometers was possible to accuracy of the order of 0.1°F. All electrical connections on the panel are covered with Dow-Corning ignition compound to prevent; electrical leakage due to moisture condensation. This, together with the high resistance of the thermometers and components of the bridge, gave much more reliable results than previously obtainable."

Jan 1, 1950

By A. D. Misener

Introduction Temperature gradients have been determined for numerous locations in the Canadian Shield in connection with mining operations (1, 2, 12, 13, 14, 15). As part of a programme of geophysical studies of this region, some of these gradients were re-determined by the writer at locations where other thermal properties, specific heat, thermal conductivity, radioactivity, etc., were also to be measured. The ultimate object was to determine the heat flow to the surface at these locations. It was felt that the practice of determining heat flow from the temperatures and conductivities obtained in a single vertical bore hole (3, 4, 5, 6, 7, 8, 9) might give results which were appreciably divergent from the average for a considerable area. Particularly, it was thought that temperature gradients, whether obtained in a single vertical hole or from a number of random locations at various depths in a mine, might be subject to local variations and anomalies serious enough to render unsure any discussions based on them. The procedure followed in this investigation was to select a location where mine workings extended to considerable depth over a reasonably wide area. At selected depths below surface, horizontal drill holes extending into regions of undisturbed rock were located and resistance thermometers were inserted into these holes far enough to record the true rock temperature. An attempt was made to obtain a sufficient number of readings at or near any one level to give a representative coverage of the area selected. This ideal could not always be attained, but the large number of readings obtained for each are a does give a reasonably representative picture of the temperature conditions. These readings required much rime and movement of men and equipment underground . They could not have been obtained without the wholehearted co-operation of the management and considerable assistance from the personnel of the mines concerned.

Jan 1, 1949

By A. Cummings

This paper reports two aspects of reactivity of complex Ni-Cu sulphide ores: variations that result from stockpiling of a nickel-copper sulphide ore in the Sudbury area and its consequences on flotation behaviour, especially in terms of metal losses to scavenger tails. In relation to the first aspect, self-heating characteristics of the stockpile were carried out by monitoring the internal temperatures of the stockpile. Six heat sensors were installed with respect to external conditions in local weather during a 7-month period. Stockpile temperatures were mainly influenced by ambient temperature with some retardation effects. The maximum temperature recorded in the stockpile was 44 °C. Samples taken at the beginning and at the end of stockpiling were tested to assess variations in behaviour of the rougher-scavenger flotation. Relative to the fresh ore, nickel and copper losses in flotation of the stockpile fines were 5.0 and 3.6 %, respectively. The fresh ore yields concentrates with higher nickel grades due to differential flotation behaviour of pentlandite and pyrrhotite relative to the stockpile fines, which exhibit a truly bulk flotation behaviour at least during the first 3 stages.

Aug 1, 2013

By Baisheng Nie, Longlong Yang, Tao Yang, Wenjie Jia

"Gas adsorption in coal is an exothermic and physical process. Temperature might change during the dynamical process. In order to get the temperature variation of gas adsorption process, the experiment system which can test the temperature variation and analyze the thermal effect was established. Gas adsorption experiments under different conditions were done by using the test system. The results show that temperature increases during the adsorption process. It is an exothermic reaction process. Also, the temperature variation and the variation gradient increase with the increasing of equilibrium pressure. The temperature variation value is smaller if the experiment temperature is higher. The paper will provide basic experimental data for explaining gas adsorption mechanism better.INTRODUCTIONChina is the largest coal producer in the world while it also has the most serious coal mine disasters. According to the statistics, there are nearly a thousand coal mines in China including more than 110 the key state-owned mines risking to happen coal and gas outburst. Hundreds of coal and gas outburst occur each year which often causes serious casualties and economic losses (State Administration of Work Safety, 2007). With the continuing exploitation of the coal resources, the depth of the Chinese coal mines increases about 100 meters every year which causes the situation of gas accident becoming more and more serious (Xie et al., 2006).At present, the real mechanism of gas adsorption, desorption and the diffusion process in coal and the influence factor of it are not so clear. And because of the limit of prediction method and the technological level caused gas accident prevention theory and technology not so valid."

Jan 1, 2015

By S. Rash Ahmadi

One of the most important elements in power plants is rotors and repairing the damaged rotors is very important in view point of economics. One of the most complicated problems in power plants is increasing of stiffness of the turbine rotors. This problem which occurs mainly due to thermal shock or rubbing makes to exit damaged rotor from service. These elements can be repaired effectively by heat treatment methods. Tempering heat treatment is the most common solution for straightening of damaged rotors but it requires having good knowledge about heat treatment parameters (temperature and time) and their affects on fundamental properties of rotors. In this article, a suitable method is introduced in order to modify the increased stiffness in journal part of rotors due to martensite transformation, using heat treatment tempering process.

Oct 1, 2011

By J. L. Jambor, E. J. Reardon, E. C. Appleyard, J. A. Cherry

Since the 1957 initiation of deposition of mill tailings at the Heath Steele mine, New Brunswick, periodic detailed studies of the tailings geochemistry and mineralogy have been conducted, thereby providing a unique opportunity to examine the geochemical evolution of a sulfide rich mine>tailings impoundment. When deposited, the tailings contained about 85 wt% sulfide minerals, 1 wt% to 3 wt% carbonate minerals, and 12 wt% to 14 wt% alumino silicate minerals. Mineralogical examination of samples of the tailings from deep in the impoundment indicates that little oxidation occurred prior to tailings deposition. The mill process-water deposited with the tailings was neutral to slightly basic and contained low concentrations of Cu, Pb, Zn and As. Sampling of the tailings five years after deposition indicated that sulfide-oxidation reactions, occurring near the tailings surface, had decreased the tailings-water pH and increased the concentrations of Fe, S042-, Cu, Zn and Pb (up to 10 000 mglL, 25 000 mg/L, 2.5 mg/L, 200 mg/L, and 4.5 mg/L, respectively). In 1975, ten years after decommissioning, the tailings could be divided into three zones: an upper oxidation zone in which sulfide oxidation is actively occurring, a hardpan layer, 15 cm to 20 cm thick, composed of tailings cemented by secondary Fe minerals, and an underlying reduction zone in which the tailings are relatively tin oxidized (Boorman and Watson, 1976). Chemical analyses indicated the presence of low-pH waters containing very high concentrations of SOi-, Fe, and other metals (up to 63 600 mg/L SO42-, 28 600 mg/L Fe, 10 mg/L Pb, 600 mg/L Cu and 4000 mg/L Zn), suggesting that there was a period of intense sulfide oxidation between five and ten years after tailings deposition. More recent sampling, conducted some 20 years after the end of tailings deposition, indicates that relatively little change has occurred in the last ten years, thereby suggesting that the hardpan layer has provided an impediment to the downward movement of dissolved constituents. Analyses of the tailings solids show increased accumulations of many metals at or near the depth of the hardpan layer. Evaluations of the long-term evolution of the tailings can be enhanced by comparison of descriptions of the tailings with descriptions of the gossan that overlay the massivesulfide orebody prior to mining. At Heath Steele, this comparison suggests that many of the mechanisms controlling the distribution of metals in the tailings will probably persist over geologic time.

Jan 1, 1992

By J. L. Jambor, E. J. Reardon, E. C. Appleyard, J. A. Cherry

Abstract- Since the 1957 initiation of deposition of mill tailings at the Heath Steele mine, New Brunswick, periodic detailed studies of the tailings geochemistry and mineralogy have been con­ ducted, thereby providing a unique opportunity to examine the geochernical evolution of a sulfide- rich mine-tailings impoundment. When deposited, the tailings contained about 85 wt% sulfide minerals, 1 wt% to 3 wt% carbonate minerals, and 12 wt% to 14 wt% aluminosilicate minerals. Mineralogical examination of samples of the tailings from deep in the impoundment indicates that little oxidation occurred prior to tailings deposition. The mill process-water deposited with the tailings was neutral to slightly basic and contained low concentrations of Cu, Pb, Zn and As. Sampling of the tailings five years after deposition indicated that sulfide-oxidation reactions, occurring near the tailings surface, had decreased the tailings-water pH and increased the concentrations of Fe, SOi-, Cu, Zn and Pb (up to 10 000 mg/L, 25 000 mg/L, 2.5 mg/L, 200 mg/L, and 4.5 mg/L, respectively) . In 1975, ten years after decommissioning, the tailings could be divided into three zones: an upper oxidation zone in which sulfide oxidation is actively occurring, a hardpan layer, 15 cm to 20 cm thick, composed of tailings cemented by secondary Fe minerals, and an underlying reduction zone in which the tailings are relatively tinoxidized (Boorman and Watson, 1976). Chemical analyses indicated the presence of low-pH waters containing very high concentrations of SO42- , Fe, and other metals (up to 63 600 mg/L SO42-, 28 600 mg/L Fe, 10 mg/L Pb, 600 mg/L Cu and 4000 mg/L Zn), suggesting that there was a period of intense sulfide oxidation between five and ten years after tailings deposition. More recent sampling, conducted some 20 years after the end of tailings deposition, indicates that relatively little change has occurred in the last ten years, thereby suggesting that the hardpan layer has provided an impediment to the downward movement of dissolved constituents . Analyses of the tailings solids show increased accumulations of many metals at or near the depth of the hardpan layer. Evaluations of the long-term evolution of the tailings can be enhanced by comparison of descriptions of the tailings with descriptions of the gossan that overlay the massive­ sulfide orebody prior to mining. At Heath Steele, this comparison suggests that many of the mechanisms controlling the distribution of metals in the tailings will probably persist over geologic time.

Jan 1, 1992

By I. Lazaro Roche, J. Brunner, J. Busto, X. Martin, J. B. Decitre, S. Gaffet, F. Hivert

"Muon tomography allows investigating the subsurface. Muons being penetrative, the attenuation of the muon flux depends on the quantity of matter the particles travel through, hence on the rock density and thickness. For the Temporal Tomography of rock Density using Muon Measurements (T2DM2) project, the muon flux measurements are performed in LSBB URL (http://www.lsbb.eu) in order to study the hydrogeological processes in the unsaturated area of Fontaine-de-Vaucluse karst aquifer. The suitability of the muography for this study is here numerically demonstrated. In parallel to these simulations, muon flux measurements are carried out in the LSBB galleries by means of a set of four scintillator tanks and Micromegas detectors are developed. These detectors, here described, are adapted for underground and confined spaces as well as other environments. Their performances are particularly interesting and should contribute to the expansion of muon tomography in new application fields. INTRODUCTIONMuon tomography or muography is a method to image large volumes by measuring the absorption of cosmic ray muons. It uses, in a passive way, a natural radiation source: the muons which are charged particles produced in the atmosphere. Primary cosmic rays interact with atmospheric nuclei and produce a huge number of secondary particles, including muons. Due to their important mass compared to electrons, they are highly penetrating, reaching several hundreds of meters below the surface. Their attenuation depends on the quantity of matter they cross. That's why they are used to investigate the subsurface, muon absorption measurement allowing to estimate the in-situ density of the rock.Georges (Georges, 1955) proposed in 1955 to use the muons in order to study the density variations caused by the overburden over an Australian tunnel. In 1970, Alvarez (Alvarez, 1970) imaged the internal structure of Chephren Pyramid thanks to this method. The muon tomography has been particularly developed for volcanology (Nagamine, 1995; Tanaka, 2007; Lesparre, 2010; Carloganu, 2013) over the last twenty years. Since the beginning of the 2010's, a growing amount of projects that proposed to use the muons in various fields get underway: the CO2 storage (Kudryavtsev, 2012), the exploration of Mars (Kedar, 2013), etc."

Jan 1, 2015

By A. Lee Barrett

"THE COAL INDUSTRY of the United States• and Canada has made great progress in recent years. Coal mining in •the old days represented one of the most arduous tasks for labour and industry, but over the years great progress has been made in reducing the effort required from labour. Also, the tonnage produced per man, the cost of the coal per ton, and the overall safety of the operation, have been greatly improved.Looking back over the past fifty years:, the era can be divided into four principal parts: (a) hand-loading, (b) track mining methods, (c) off-track mining methods, and (d) continuous mining. For many years, all of the coal was won by hand-mining methods. The first forms of mechanization •resembled the move from the horse •and buggy to the automobile. Early track mechanical mining methods were usually adaptations of the direct methods involved in hand-mining, with each improvement directed toward some specific process. A revolutionary development came about with off-track mining methods. The first efforts in this direction were provided by off-track mechanical loading machines, which loaded the cars •on track and differed from conventional track mining methods only in that the loading machines themselves operated on the mine floor. With the advent -of the shuttle car about ten years ago, true off-track mining came into being, and real progress in this direction began to be made.At the present time we •are at the beginning of a new era -.the era of continuous mining. There will be a period of development with some time needed before the system is generally applied throughout the industry, but -already enough •has been done to indicate rather dearly what the future holds in this direction."

Jan 1, 1953

By C. Schuffeneger

"The design of SAG milling circuits for mining projects requires the incorporation of the energy consumption considerations and the evaluation between different flexibility-adding options to absorb the time-dependent variation in the ore lithology. In order to expand the focus of the engineering design, a higher level of deepness and quality in the baseline information must be achieved to elucidate all of the constraints on throughput, energy consumption and product quality generating a design optimization consistent with an integrated vision of the process. This paper presents a review of a collection of typical examples of the copper and gold mining project in the Chilean Andes, in which both process and energy efficiency criteria are considered when the focus is to deliver an integral solution that incorporate those areas in the design. The intensive use of energy in the SAG milling, the process continuity and the quality of the product are a function of the proper design and selection of grinding equipment and plant layout, aligned with the mining plan and associated with projected future expansions and production increases.INTRODUCTION Autogenous and Semiautogenous grinding technology, large diameter and short length mills, begins with the Handsel design. During the decade of 1930’s, Handsel-Hardinge studies led to cascade mill development. Nowadays, 80 years later, continuous improvements in design and technology have been conducted to a completely new generation of gearless SAG mills that have led to an increasing capacity at the concentrator plants. Considering the existing alternatives, SAG mills are the most implemented option for the grinding circuit today. This work presents a review of the SAG mill implementation parameters and circuit considerations and its correlations in the most recent projects in Chile with an ore treatment capacity above 50 ktpd since the decade of the 90’s up to now. From this period, the tendencies will be analyzed using project design data. Based on process design information, the recent SAG mill history in relevant projects related to the new generation of commercial SAG mills, technical associated considerations and performance will be discussed. Circuit selection based on energy utilization will be revised to bring up a more holistic perspective on the SAG mill circuit design concepts. As is now well known, the heart of every concentrator plant are the grinding mills. Higher demands on throughput, availability and power consumption optimizations require not only high performance electrical equipment but also a well selected grinding circuit. The energy efficiency issues associated to the circuits design will be reviewed."

Jan 1, 2012

By E. Herrera Alarcón, L. Mariscal Samaniego

The Teniente Converter (wet charge type) was commissioned in august 1995 and was designed to smelt 744 tpd (metric tons per day) of dry copper concentrates. Its products are white metal (73% Cu) that is sent to the Peirce Smith converters, slag that is cleaned in Reverberatory Furnaces and the process gases that are sent to the Sulfuric Acid Plant. Since its start up, the Teniente Converter smelting capacity was increased 1.6 times, from 800 tpd to 1,280 tpd using 33% oxygen-enriched air, and reaching an operative availability of 97%. By the other hand its campaigns have reached a record duration of 530 days without hot patching tuyeres and a partial refractory lining repair in the last four campaigns. This paper describes the most relevant improvements, as well as the strategies that had been used to reach these achievements.

Jan 1, 2007

Most of automotive magnesium applications are presently produced by high-pressure die casting processes, For further expansion of the alloy usage in automobiles, novel-manufacturing processes needs to be developed, In this study, squeeze casting of AM50 alloy was carried out using a hydraulic press with an applied pressure of 70 MPa, Tensile properties and fracture behavior of the squeeze-cast AM50 were characterized in comparison with the die cast counterpart, The squeeze-cast AM50 alloy exhibits virtually no porosity in the microstructure evaluated by optical microscopy, The results of tensile testing indicate that the improved tensile properties for the squeeze-cast samples over the conventional high-pressure die-cast parts, The analysis of tensile behavior shows that the strain-hardening rate during the plastic deformation of the squeeze-cast specimens is constantly higher than that of the die-cast specimens. The SEM fractography evidently reveals the ductile fracture features of the squeeze-cast alloy AM50.

Jan 1, 2005

By A. M. A. Mohamed, F. H. Samuel, S. Alkahtani

"This article was undertaken to investigate the effect of nickel and zirconium additions on the strength of 354 aluminum cast alloy. The cast alloys were given a solutionizing treatment followed by artificial aging at 190 ºC for 2 hr. High temperature tensile tests were conducted at various temperatures from 25ºC to 300ºC. Optical microscopy and scanning electron microscopy were used to study the microstructure of the samples. The results revealed that the intermetallics phases of (Al,Si)3(Zr,Ti), Al3CuNi and Al9NiFe are the main feature in the microstructures of alloys with Zr and Ni additions. The results also indicated that the tensile strength of alloy decreases with an increase in temperature. The combined addition of 0.2 wt% Zr and 0.2 wt% Ni leads to a 30% increase in the tensile properties at 300ºC compared to the base alloy.INTRODUCTIONThe task of improving the mechanical properties in an aluminum alloy at high temperatures should include the knowledge of several factors which are related principally to a decrease in the strength of the metal with increasing temperatures. This behavior is linked to the change or deterioration in the principal metallurgical parameters of the specific cast aluminum alloy during its performance at higher temperatures. Most of applications of Al-Si casting alloys are generally used at temperatures of no more than 230°C (Lee & Chen, 2002). This recommendation is made in view of the fact that, for certain applications such as those required by the automotive industry, these alloys must operate over a wide range of temperatures and stress conditions where temperatures are liable to rise even higher than 230ºC (Robson & Pragnell, 2003).Aluminum-silicon-copper-magnesium alloys such as the 354 alloys show a greater response to heat treatment as a result of the presence of both Mg and Cu. These alloy types display excellent strength and hardness VALUES (although at some sacrifice of ductility and corrosion resistance. These alloys are used for a wide range of applications, such as engine cooling fans, crankcases, high speed rotating parts, structural aerospace components, air compressor pistons, fuel pumps, compressor cases, timing gears, rocker arms, machine parts, and so forth (Cáceres, Svensson, & Taylor, 2003; Rurrxia, Rong-de, Yu-hua, Cherrxi, Xiao-feng, Heng-rong, & H. Zhuang-qi, 2004)."

Jan 1, 2012

By F. Dai

Granitic rocks usually exhibit strongly anisotropy due to pre-existing microcracks induced by geologic loadings. The understanding of the rock anisotropy in mechanical properties such as tensile strength is critical to quarrying and stabilization of underground structures. In this paper, Brazilian tests are conducted in combination with MTS material testing machine and split Hopkinson pressure bar (SHPB) system to measure both static and dynamic tensile strength of anisotropic Barre granite. Samples are cored and labeled using the three principle anisotropic directions of Barre granite (BG). These directions are also chosen as the loading directions for the Brazilian discs. For dynamic tests, pulse shaping technique is used to achieve dynamic equilibrium in the samples during the test. Finite Element Method is implemented to formulate equations that relate the failure load to the material tensile strength employing a orthotropic model for Barre granite. For samples in the same orientation group, the tensile strength shows clear loading rate sensitivity. The tensile strengths exhibit clear anisotropy under static loading; while less anisotropy under dynamic loading. The tensile strength anisotropy of Barre granite is interpreted as interactions of the pre-existing microcracks.

May 1, 2009

By Erwin L. Zodrow

"For 25 chemical elements in electrostatically precipitated fly ash (Lingan coal-fired power station), concentration changes are studied as a function of increasing proportions of fines (ash particle diameter less than 45 micrometres). Elements that are involved when concentrations increase as the proportions of fines increase are likely to escape into the atmosphere. These are Th, U, As, S, P, Sb, Na, Ag, Zn, Pb, Ni, Ba, Sc, AI, Mo (and Bi, Ge, Ga, F and Li), i.e., more or less highly volatilized elements. Of the less volatilized metals such as Fe, Ca, Cu, Ti, K, Co, Mn (and lanthanides), certain portions presumably also escape as stack emissions. Diadochy and spinel formation in bottom slag is presented as an emission-reducing agent for certain metals.IntroductionThe Lingan coal-fired power generation plant, owned and operated by the Nova Scotia Power Corporation, produces annually about 140,000 metric tons of ash (the residual mineral content after burning coal). The tonnage is based on a 15 per cent average ash content of Cape Breton coal.For purposes of this report, samples of the hard, fused slag (bottom slag) that is accumulated at bottoms of boilers, and electrostatically precipitated fly ash (ep ash), were collected and investigated. Bottom slag is a minor component of the produced ashes.The ashes were surveyed and the presence of over 75 major, minor and trace elements is reported. From this survey, 25 elements were selected to establish elemental enrichment/depletion trends when the proportions of the less than 45 micrometre <45µm) fractions in ep ashes increase. The results are significant in that, taking the case of elemental enrichment, the elements involved are likely to escape into the atmosphere, i.e, highly volatilized elements. Depletion trends for elements are presumably associated with less volatilized elements during coal-firing. Quantification of the emission of atmospheric pollutants is not considered part of this work. ""Igneous"" minerals generated during coal combustion include spinels (found mainly in the bottom slag), quartz, glass and mullite."

Jan 1, 1982

By Erwin L. Zodrow

"The neglect of including the toxic metal mercury in the list of escaping elements (Zodrow, CIM Bulletin, September 1982, pp. 138-140) was pointed out to the author in a private letter by J.E. Rehder, dated September 21, 1982. I welcome this opportunity to present my preliminary mercury research data based on coal investigations supported by N.S.E.R.C and the University College.As mercury is a volatile element and liquid at room temperature, special analytical techniques are required to determine concentrations in whole coal. In the investigation, the coal is analyzed by flameless atomic absorption with a lower detection limit of approximately 10 parts per billion, which, however, is a function of the ash contents of the coals (personal communication, J.L. Brooker, XRAL, 1981).Coal seams of the Sydney Coalfield studied so far include: the Point Aconi, a thin shaly coal, the Upper Bonar, an overrider of the Harbour seam, and the Harbour, Shoemaker and McAulay seams, all of which are shown in stratigraphic succession in Figure 1. The seams have been channel-sampled taking 15-cm coal intervals as one sample for analysis. One channel sample has been investigated from each of the seams listed (two channels were taken from the Point Aconi seam), resulting in 38 samples. Table 1 shows the results, which include mercury contents, ash and total sulphur per sample interval. Figure 2 is a frequency distribution of the 38 determinations."

Jan 1, 1982

By Ike Isagon

Outline 1.Background Sudbury Backfill Operations 2.Alternative Binder 3.Alternative Binder Trial Process Flow Diagram ?Laboratory Results ?Plant Trial ?Final Evaluation and Approval ?Management of Change (MOC) 4.Economics 5.Conclusion 6.References and Acknowledgements

Nov 1, 2011