Search Documents

By J. N. Hilton, D. Moffett, E. Barnes

"A recent pilot-plant program carried out at Rio Algom's Quirke uranium mine at Elliot Lake, Ontario is described. The goal of the research was the production of tailings basin effluents which were low in total radium-226. The process tested involved precipitation of radium with barium chloride and sedimentation in plastic-lined settling ponds. Adjustment of the tailings basin overflow from its normal value of pH 9.5 by addition of sulphuric acid to about pH 7.5 was found to give approximately a five-fold improvement in total radium-226 removal. A five-month demonstration test resulted in an effluent with a mean total radium-226 activity of44 pCi/L after 2.5 days settling time and 29 pCi/L after 5 days. The results from the demonstration program are used to propose a schedule of achievable total radium-226 activities where precipitation and sedimentation are employed. The maximum suggested values for 5 days nominal settling time are: 30 pCi/L in an annual mean, 45 pCi/L in a monthly mean. 60pCiIL in a weekly mean and 80 pCi/L in any single grab sample.IntroductionRadium-226 has been removed from effluents at the Elliot Lake uranium mines since the introduction of the first barium chloride treatment system in 1965. Current practice, which has changed little over the years, consists of radium-barium sulphate precipitation by the addition of a low do se of barium chloride to the clear overflow from the tailings basin(l·2l. Provision is made for the precipitate to settle in large natural or constructed ponds and lagoons. The residence time in these ponds, which depends on the site, ranges from 3 to 35 days, with varying degrees of efficiency being achieved."

Jan 1, 1981

By R. Webber, D. Averill, L. Whittle, D. Moffeti, G. Kassakhian

"This paper describes the recent pilot-plant work carried out on two alternative processes capable of producing an effluent containing less than 10 pCi/L total radium-226 activity and very close to 3 pCi/L dissolved radium-226. The processes incorporate coprecipitation of radium with barium sulphate by the addition of barium chloride in continuously stirred tank reactors followed by either chemical coagulation with ferric chloride, flocculation and clarification, or polymer-aided dual-media filtration. IntroductionUranium mines in Canada have practiced radium removal from tailings basin effluents since 1965. Treatment consists of addition of barium chloride to precipitate radium as barium- radium sulphate and provision of natural or constructed settling ponds for sedimentation. This process, however, has been identified as being deficient in that it allows particulate or suspended radium-226 releases which are higher than the regulated dissolved values». Also, the large size of some of the settling ponds is believed to represent a real limitation of the present technology because of inferred difficulty in recovery of barium-radium sulphate precipitates.The Federal Government Mining Task Force established a Radioactivity Sub-Group in 1974 to assist in the development of effluent regulations and guidelines for the uranium mining industry. Among the recommendations of the Sub-Group was the need to seek more effective methods of radium removal, including development of physical/chemical treatment systems as an alternative to settling ponds. In response to the SubGroup recommendations, a bench-scale study began in March 1976at the Wastewater Technology Centre (WTC) of Environment Canada . The results of this study indicated that coagulation and flocculation of the precipitate from barium chloride addition is a viable alternative to sedimentation in settling ponds(3). The bench work was expanded and accelerated in 1977, with financial assistance provided by the Atomic Energy Control Board. Subsequently, a research program with a larger scope was developed; this program is jointly managed and funded by government and industry, as shown in Table I.One of the goals of the joint program is to develop, at pilot scale, a physicalI chemical process to reduce the radium-226 content of uranium mining and milling effluents. Target radium-226 activities for treated tailings basin effluents were set: namely, 10 pCil L total and 3 pCil L dissolved radium 226. Extensive bench-scale and pilot-scale work was conducted through 1978 and 1979 and has culminated in the development of two physical/chemical processes. This paper describes work carried out at a pilot plant which led to the selection of the two physical I chemical processes for demonstration. In short-term tests, the processes produced effluents meeting the radium-226 target activities."

Jan 1, 1980

By James F. Archibald, H. Jame Hackwood

"Research was performed to assess the feasibility of barrier membrane substances, for use within mining or associated high risk environments, in restricting the diffusion transport of radon gas. Specific tests were conducted, both within laboratory and in situ environments, to determine radon gas concentration ratios across a barrier of interest and emanation rate variation resulting from application of such materials. Several materials have been demonstrated to be effective in restricting the emanation of radon gas into initially radon-free environments. One liquid material shows particularly good promise upon consideration of ideal radon barrier criteria.IntroductionIt has long been known (I.2.3) that inhalation of the short-lived, alpha particle-emitting daughters of radon gas can result in irradiation of lung tissue with the potential for causing lung cancer. Control measures are necessary to maintain concentrations of airborne contamination at a minimum to protect miner health and safety. Typical control practices in mines have been through the application of systematic ventilation and backfilling of excavated opening. As mines become deeper, however, and additional workings become exposed, increased ventilation capacity requirements are needed. As an alternative to other radiation control measures, the use of sealants to prevent radon migration from walls into mine atmospheres may provide a suitable engineering alternative."

Jan 1, 1987

By Cardm Jeffrey W.

The decay of 222 Rn yields a series of short-lived decay products which become attached to the surface of a plate or wire exposed in a 222Rn-bearing atmosphere. The alpha-activity of two of the decay products, 218Po and 214Po, can be measured by simple counting techniques. This phenomenon may have direct application to uranium exploration. Laboratory studies have shown that: (a) radon decay products can be collected on a wide variety of materials (including various kinds of metals and plastics); (b) activity increases as a function of the surface area of the 'collector; and (c) the collection of the decay products is enhanced by applying a negative charge. The new technique was used in situ to delineate the anomaly above the South March uranium-copper occurrence. A related technique was developed to measure radium in soil samples. The results of both studies compared favourably with those obtained from conventional methods.

Jan 1, 1979

By R. H. McCorkell

Radon emanation rates. J. and compositions of materials from the Canadian Certified Reference Materials Project (CCRMP) indicate that the fraction of the Rn produced that escapes, E, is usually 1% to 8% and the 238U decay chain is nearly in secular equilibrium. For some Chinese ore standards, E values are higher than f or the CCRMP materials. Standard ore tailings have 2/oPb concentrations higher than expected from their 226Ra concentrations and Rn escape rates (12 - 34%) . Biological materials have E ˜100%, their ash E ˜0%. Pelletizing ore powders at 20 000 lb/in2 reduces J by only 20 - 40% but only 2% of Rn escapes from pressed Li2B4O7 pellets and 0.01 - 0.04% from fused Na2B4O7 or Li2B4O7 discs. Large, difficult-to-explain random variations in J are observed in some situations but several highly reproducible ways of measuring emanation rates have been found.

Jan 1, 1986

By J. Font

The RAF or copper fire refining process at the Caletones smelter of CodelcoChile consists of several pyrorefining stages that successively lowers the levels of S, Fe, Pb, As, Sb, Te, Se and to some extent 0 in the copper melt, allowing the production of high quality fire-refined copper of 99.93 % purity (RAF copper). This chemical feature of the RAF copper is only achieved by quite long processing times, and a considerable consumption of fluxes and fuels in the RAF vessels. The main goal of this study was to improve the RAF process performance by thermodynamic considerations and industrial scale tests, i.e., an in situ approach for the process as featured by intensive sampling, characterization and subsequent modifications. Thus, both theoretical and industrial data were derived, and based on kinetic and thermodynamic evaluations, a higher operational standard was achieved for the RAF process. These new operational practices allowed enhancing the overall economic of the RAF process, by reducing the time and operational costs, and consequently increasing the availability of the vessels.

Jan 1, 2007

By T. F. Pugsley, D. Gignac

"The historical background to the project dates back to the mid-30s with the discovery of surface sulphide showings in the Cape Smith-Wakeham Bay ultramafic belt. In the mid1950s, orderly exploration commenced with an extensive work program by Asarco, INCO, Lemoine, Falconbridge and Raglan Nickel Mines Ltd. on exploration permits. In 1966, Falconbridge and Raglan Nickel Mines interests merged. Extensive exploration, drilling, under- ground delineation of the Donaldson orebody and the construction of basic infrastructure such as camps, airfield, road links from Douglas Harbour to Donaldson and Katinniq, a distance of 60 km, were completed.Production project design at that time consisted of plans for a 50 000 mt per year nickel mining and concentrating operation, including a 2000 person community and smelter at Douglas Harbour. These plans unravelled in the mid-70s due to high capital costs, poor nickel market conditions and the realization that the Raglan orebodies were not large enough to economically support the construction of green field smelter and refinery facilities for processing Raglan production. Nickel market conditions in the late 70s and early 80swere generally poor, resulting in further delays on production plans.While recognizing the very high potential to discover increased tonnages of high grade(3% Ni) in excess of 20 million tonnes, the project was deferred into the late 80s when a serious re-evaluation of exploration potential occurred and the requirement to prove up additional reserves resulted in an underground exploration program at Katinniq covering the period 1990-1992."

Jan 1, 1996

By Richard P. Reiff

"The Facility for Accelerated Service Testing (FAST) program has been involved in numerous rail wear tests since its inception in 1976. A number of specialized tools have been developed to aid in assessing specific performance parameters including gauge face wear, head height loss, metal flow, head area loss, hardness, and welded rail end batter. The layout of a test site, including position in curve, number of measurements per rail, and train operation must be properly controlled/monitored to provide valid wear comparisons.This paper will provide an overview of the above-mentioned tools and techniques. In addition, a summary of recent test results from FAST, including information on head hardened rail investigations, will be provided. A set of guidelines for establishing a revenue service field test site will also be provided to aid users in performing evaluations of their own.IntroductionBackground of Rail Wear Testing at FASTThe Facility for Accelerated Service Testing (FAST) located at the Transportation Test Center, (TIC), Pueblo, Colorado has been involved with testing of rail since program initiation in 1976. A huge data base of rail wear information has been gathered from FAST operations under a variety of rail metallurgies, lubrication conditions, and measurement techniques. Attempts at obtaining meaningful rail wear information from early (1976-1978) FAST rail wear data was hampered by two main factors: (I) measurement techniques were insufficiently accurate for the amounts of wear being experienced, and (2) the lubrication was not sufficiently controlled to obtain uniform conditions for a sufficient measurement time period.Subsequent test periods were operated with improved measurement techniques and controls that ensured statistically valid data. The policies and conditions that permit accurate rail wear assessment will be reviewed and outlined in this paper, along with some specific TIC and field examples that will allow the user to improve the accuracy of a field rail test on their own operating property."

Jan 1, 1988

By Patrick Fantin

Mining ? The Past Safety Not a priority; Health Not a priority; Energy Manual Labour; Horsepower? Literally. Financially Robust For the Owner?s; Mining ? The Future Safety Zero Harm Health Understanding and elimination of Industrial Disease Energy Efficient use of energy through technology. Full value of renewable energy. Financially Robust Continually build shareholder value through optimum CAPEX/OPEX.

May 1, 2013

By B. H. Sadagah

"Construction of mountain roads at north westerly Saudi Arabia is a difficult task in rugged terrains, where the rock masses are steep slopes, and full of geomorphological constraints.Werka descent lies at the north west region of Saudi Arabia. The Werka descent, constructed four years ago harmed due to rainstorm. The rock masses are metabasalt and metaryolite tuff rocks. The road is eight m-wide, surround by unsupported sharp manmade slope cuts, reaches up to 15 to 40 m height on both sides. Failures took place at both sides of the road, and blocked it. The road of almost 2 km long subjected to all modes of slope instability such as rockfalls, manmade slope failures and debris flows in the absence of the remedial measures. The very precipitous 40 m-high rock slope-cut along the road has no benches, backed by a natural slope of almost 80 m height. Both types of slopes suffer from rockfalls and slope failure’s incidents, frequently took place mainly in rainy seasons. The steep manmade rock slope cut is less than 1 m close to the road, with no ditches, form a potentially source area for rockfall’s hazards.Intensive geotechnical study includes utilization of the RMR and GSI rock masses classifications indicates that the rocks are fair to poor quality. The DIPS, RocFall, Swedge, RocTopple, RocPlane computer program, in addition to GIS and DEM image utilized to perform modeling and deterministic analysis, in order to suggest the mitigation measures for the natural and manmade slope cuts and rockfalls. The seismic coefficients of 0.1 to 0.4 taken into consideration in modeling processes. Input parameters to model the rockfalls and slope failure’s characteristics were studied such as GSI, block size; seeder points, locations of fallen blocks; slope angle, restitution coefficients, and slope roughness. The programs modeled the proposed location, height and energy of the rockfall barriers, collectors, and rock bolts. Two manmade slope cuts studied and modeled utilizing the integrated techniques were to eliminate the risk of slope failures and rockfalls through the construction of remedial measures, this is the study objectives."

Jan 1, 2015

By John G. Ayttes

"The following is a review of the advance of raise boring and its current position. The viewpoint presented is that the mining industry, through its worldwide acceptance of raise boring, has acknowledged the success of the method in general. Acceptance, however, does not imply complete satisfaction with either the equipment or current operating costs. Therefore, a brief review of how boring costs are being r educed is presented, citing examples. Recent raise borer applications of special interest are presented to show adaptability of current equipment, and some special projects in the planning stage are highlighted."

Jan 1, 1972

By W. J. Taylor, T. D. Parris

"Over 90,000 feet of raise have been bored at International Nickel underground mining operations throughout the Sudbury District since the advent of raise boring in the early part of July, 1964. With a total of 10 raise borers on hand at this time, techniques have improved steadily since introduction at INCO mines. The first unit, designed for use in rock of low compressive strength, had to be modified and redesigned to cope with Sudbury Area Precambrian rock. As equipment and boring techniques improved, a specially designed machine for larger holes was developed and is now in use. More powerful units, with a thrust capacity of up to 750,000 pounds, are under investigation. Raises have been bored up to 84-inch diameter, and the changeover to 5- and 6-foot flat reaming heads with improved cutter design has increased performance substantially. As a result, 5-foot-diameter raises have been completed to a length of 750 feet and 6- and 7-foot raises to over 500 feet. Reference is also made to the drilling of over 23,000 feet of drainage and sand-fill holes, ranging up to 7% inches in diameter, with smaller underground rotary drill equipment.Finally, a look into the future indicates the need for further improvements in equipment design to permit economic boring of 7- to 8-foot-diameter raises in Sudbury Area ground types."

Jan 1, 1972

By Lyle F. Smith

With the demand for larger diameter raises under all ground conditions and the increasing price of drill rods and operating costs, it was evident that there was a need for a raise borer with a variable-speed drive and fast-response torque limiting control. The raise boring machine described in this paper was developed after several years of market research and discussions with mine operators and construction contractors. This paper discusses the Ingersoll-Rand raise borers with the solid-state controlled DC motor drives. These machines have gained wide acceptance in the five-year period since being placed in operation and are designed to accommodate the range of raise diameters and lengths most required today.

Jan 1, 1978

By B. Burger, T. Bester, S. Deonarain, L. S. Schultz

"This paper details the process followed to raise drill and equip a 6.1 metre diameter vertical service shaft at Glencore’s Mindola Deeps project in Kitwe, Copperbelt Province, Zambia. The project scope comprises a shaft collar, bulk air intake, a pre-sink to -90 metres and raise drilling the shaft from surface to a final depth of 1,892 metres underground, in four separate lifts of approximately 475 metres each. Equipping of the shaft steelwork, headframe erection and commissioning the shaft for hoisting. In addition, the scope included the development of a decline down from 5430’ level underground to the new shaft position on 6205’ level. This paper will provide some insight into the successes and challenges encountered during execution of the shaft works to date and provide some learnings for future projects of a similar nature. INTRODUCTION The Mindola Mine is situated to the west of the city of Kitwe in the Copperbelt Province of the Republic of Zambia (Figure 1). The mine is owned and operated by Mopani Copper Mines Plc (MCM), whose shareholders are Glencore AG (73.1%), First Quantum (17.9%) and ZCCM Holdings Plc (10%).Productivity at the Mindola mine has been adversely affected because of significant ventilation and ore re-handling challenges, which are caused by the dilapidated infrastructure, and design of the existing vertical and sub vertical shaft system. In the circumstances, it was apparent that it was necessary to sink a new vertical shaft that would increase the volume of fresh air down the mine, improving the underground working environment and the current hoisting restrictions, resulting in an increase in productivity and efficiency. Because there were two existing levels ideally situated and perpendicular to one another and because a third level was in close proximity to that perpendicular and because the mine required a ramp down to shaft bottom in any event, consideration was given to raise drilling the shaft as opposed to using conventional blind sinking methodologies."

Jan 1, 2019

By Jos. Kalbhenn

PART of the plan of re-allocation evolved by the engineers of the Dominion Steel and Coal Corporation in 1932 to retard the rapid advance of the submarine workings seawards was the opening of Dominion No. 20 Colliery, in the Harbour seam, by a pair of cross-measure tunnels from the workings of an older mine working the Phelan seam, which lies 430 feet below the Harbour seam. The tunnels, 8 ft. by 13 ft. in size, were started away from the old workings of Dominion No. 2 at a point 1.5 miles beyond the shore line and were driven on a rising grade of 1 per cent for a distance of 5,335 feet, tapping the Harbour seam at a point 2 ¼ miles off-shore. For transportation and ventilation, shafts and roadways already existing in the Phelan seam were made use of during the stages of development and up to the present time. One of the two tunnels served as a main haulage road and an intake airway, and the other as a return airway and travelling road. However, as the workings of this new colliery expanded, the need for additional airways arose as was anticipated when the plans for the development were formulated. To meet this need, work was started on October 1st, 1942, to establish a new opening between Nos. 2 and 20 Collieries in the form of a vertical shaft to provide a passageway for the ventilating air current of some 250,000 cubic feet per minute on its return to the upcast shafts in No. 2 Colliery, thus making both tunnels available for intake airways. In the interest of safety, speed, and economy, the shaft was raised from the Phelan to the Harbour seam. It is 20 ft. by 12 ft. in size and, with the exception of three timbered compartments across the narrow end, is untimbered. One of the three timbered compartments housed the ventilating tubing and pipe lines, the centre one served as a cage-way for hoisting men and material during the operation of raising, and the third one contained a ladder way. The rest of the shaft was filled with debris during the period of shaft raising.

Jan 1, 1944

By Jos. Kalbhenn

MR. G. G. BOWSER: Mr. Kalbhenn's paper is an excellent one and is a concise description of a very interesting piece of work. It is well known that a great deal of preliminary study was given to this job before the final plans were made. It is due to this thorough preparation .chat the work progressed so satisfactorily, smoothly, and safely. The ideas carried out in the construction of the hardwood pack, timbered compartment, inclined raise, loading chute, and steel-boomed room, all contributed to a successful conclusion of the work. The extra care in being certain that the compartment shafts were well timbered was especially necessary on account of the difficult blasting conditions. In other words, the foundations .of this job were well and truly laid. The blasting in this work was very difficult due to the nature of the Strata. Working under an ever precarious roof condition and completing .this job with only two lost-time accidents is a record of which to be proud. The shaft men engaged on this work are also due for praise. I regret I did not visit this work while it was in progress. It was not in lack of interest. This, however, more or less proves that the blasting end .of this job went along with practically no trouble. I have seen the nature of the rock, as I made several visits to the tunnels while they were being put through from the Phalen to the Harbour seam. According to figures in Mr. Kalbhenn's paper, the explosives consumption works out to 1.61 pounds per cubic yard of rock in the solid, or 0.8 pounds per ton. The explosives consumption in the tunnels ran from 2.86 to 3.46 pounds per cubic yard or an average of 1.58 pounds per ton of rock. Of course, the rock in the shaft was blasted in the most economical way possible, as far as powder costs are concerned, as the face advanced at close -wright angles to the strata and gravity was acting with the explosive. The tunnels were driven nearly 'end on' the strata and bottom holes had to be lifted, and I believe there was some re-drilling of ribs left in the floor. I would like to congratulate Mr. Kalbhenn on his very fine paper.

Jan 1, 1944

By Mohammed Rachek

Résumé : la mine d?Elhammam, opération du groupe minier Marocain Managem, est située au sud de la ville de Meknes à 63 km, elle exploite un gisement de fluorine depuis 1974. La minéralisation se présente sous forme de deux filons principaux orientés N45° avec un pendage variant de 65 à 90° NW, entre ces deux filons on note la présence d?une succession de filons satellites sécants. La méthode d?exploitation pratiquée depuis le démarrage de la mine est celle des chambres magasins, elle assure une cadence d?extraction annuelle de 250000 tonnes. Cette méthode favorisée par une très bonne compétence mécanique des épontes de la minéralisation a offert à l?exploitation une rentabilité très satisfaisante grâce à son faible coût mine. Les travaux de recherche géologique menés en parallèle à l?exploitation ont permis la découverte d?un nouveau secteur ?K-Est Gouaïda? (KEG) qui fait l?extension nord-est du gisement principal, la minéralisation de ce secteur se présente sous forme de deux filons très étendus latéralement (900 m d?extension) et présentant une puissance minéralisée irrégulière et très faible 1.2 m en moyenne, les épontes de la minéralisation sont constituées de schistes de qualité mécanique très faible. Vers la fin des années 1990, l?exploitation s?est orientée vers le développement minier du secteur KEG. Ce développement consiste à faire le choix adéquat de la méthode et de l?infrastructure minière pour l?exploitation de ce nouveau secteur, KEG. La méthode des chambres magasins, pratiquée dans le gisement principal avec un faible coût mine, n?est pas praticable dans le nouveau secteur à cause de la qualité de ses terrains, l?irrégularité de la morphologie de sa minéralisation et de la faible puissance des ses filons. Seule la méthode des tranches montantes remblayées (TMR) peut être applicable techniquement vu les spécifications suscitées de la nouvelle minéralisation, la TMR doit être appliquée sous sa variante mécanisée pour faire face au niveau exigé de la production. Après le pilotage de l?exploitation par TMR mécanisée dans le secteur KEG, il a été confirmé que cette méthode donne une grande satisfaction en matière de stabilité des terrains, sécurité, sélectivité, productivité et récupération du gisement, néanmoins elle reste pénalisée par un coût mine trop élevé pour garder le niveau de rentabilité recherché par l?exploitation d?un produit de faible valeur marchande telle que la fluorine. Dans l?objectif de rentabiliser l?exploitation du secteur KEG qui représente en réserves l?équivalent d?une durée de vie de 4 à 5 ans et d?assurer la pérennité de l?activité, l?exploitation en collaboration avec Reminex, la filiale d?ingénierie de Managem, a adapté une nouvelle variante de la TMR mécanisée dite TMR avec plan incliné sur remblai. Cette nouvelle variante de la TMR consiste à réduire au maximum les travaux dans le stérile en reconstituant un plan incliné sur le remblai à l?intérieur des filons pour faire évoluer en vertical l?exploitation des tranches en montant vers la tête d?un panneau de minerai. La variante des tranches montantes remblayées mécanisées avec plan incliné sur remblai a été imaginée et appliquer en 1978 dans la mine de fluorine de Burc située au Sud-Ouest de la France (Sicard et Mailloux, 1983). Imaginée pour une cadence annuelle de 30000 tonnes et une mécanisation très modérée cette variante a été adaptée par l?exploitation de la mine d?Elhammam en 2002 pour un haut degré de mécanisation et une cadence d?extraction annuelle de 250000 tonnes de minerai. Cette variante de la TMR est appliquée depuis le début de 2003 dans les chantiers du secteur KEG, elle présente les mêmes avantages techniques que la TMR mécanisée classique et elle a permis la réduction du volume des travaux d?infrastructure de 17.65 m à 6.25 m de travaux par 1000 tonnes de minerai. Ceci s?est traduit par une baisse du coût technique de la mine de 34% ce qui a donné un nouveau souffle à la mine pour assurer sa production et pour poursuivre la recherche géologique d?éventuelles zones à mettre en valeur.

Oct 1, 2004

By David A. Grieve, David E. Pearson

"A rank-map of Crowsnest coalfield, showing the distribution of the bituminous coal measures and the locations of major structures, has been produced from vitrinite reflectance measurements on over600coal samples. The timing of coalification in relation to these major structures has also been determined.In the west-central portion of the coalfield a complete stratigraphic succession of coal measures which rides on major thrust surf aces is all of high-volatile bituminous rank, but despite the structural discordance no break in rank is discernible across these structures. The thrust faults therefore predate much of the coalification.Three major valleys expose cross sections of the folded coal measures and in each an increase invitrinite reflectance is demonstrable as individual seams are traced from ridge crest to valley floor. Thus, in these sections, a significant amount of coalification post-dates folding. The proportion of this post-folding coalification is found to increase toward the south of the coalfield.A late gravity-fault, exposed along the east crop of the coalfield, places high-volatile coal-bearing successions in contact with low-volatile coal and demonstrably is a reactivated thrust fault. Coalification at this locality occurred between these two different ages of faulting.The variations in rank and the subtleties of the coalification pattern have, together with systematic changes in the maceral composition of coal seams, had a profound effect on coal quality in the coalfield. Coking coals with a variety of properties occur together with some coals that have no caking capacity."

Jan 1, 1985

By V. S. Sastri, M. Elboujdaïni

"Corrosion rates of silicon brasses, highzinc yellow brass, low-zinc yellow brass, leadedtin bronze and silicon bronzes in both permanent-mold and sand-cast conditions were determined in soft water of pH 3, 5 and 8, and hard water of pH 8 at 70°C by electrochemical polarization technique. The alloys in permanent- mold condition showed greater corrosion resistance than sand-cast condition. Corrosion rates obtained from weight loss measurements showed no observable trend of a difference between permanent-mold and sand-cast alloys.The corrosion rates decreased with increasing pH of the medium. Silicon bronze and silicon brass showed high corrosion resistance while leaded-tin bronze showed the least resistance. Addition of small amounts of aluminum improved the corrosion resistance of silicon bronzes and silicon brasses. Alloys in permanent- mold condition showed greater resistance to dezincification than sand-cast alloys when average pit depth parameter is considered."

Jan 1, 1997

By P. Hickey, G. Hubert, P. Healy

"J. S. Redpath Limited, an underground contractor with a worldwide presence, has implemented innovative techniques in various projects in Canada to shorten the development cycle. Conventional methods currently used for installing primary ground support are compared with the Australian technique of bolting and meshing with jumbos equipped with twin telescopic booms, in-cycle shotcreting, and the use of two jumbos and two scissor bolters set up side by side in wide headings. Recommendations and lessons learned are presented with the aim of providing realistic expectations with regard to development advance rates in a mining environment.RÉSUMÉ J. S. Redpath Limitée, un entrepreneur minier souterrain d’envergure mondiale, a complété plusieurs projets au Canada où des techniques novatrices ont été mises en oeuvre pour raccourcir le cycle de développement. Cet article présente une comparaison entre les méthodes conventionnelles fréquemment utilisées pour le support de terrain, la technique australienne de boulonnage et d’installation de grillage au moyen de jumbos équipés de flèches télescopiques doubles, du béton projeté appliqué durant le cycle de développement et de l’utilisation de deux jumbos et deux boulonneuses côtes-à-côtes dans des galeries de grandes dimensions. Les recommandations et les leçons apprises sont présentées dans le but de fournir au lecteur des attentes réalistes quant aux taux d’avancement du développement dans un environnement minier."

Jan 1, 2016