Search Documents

The incidence of colliery disasters has highlighted the need for more centralised and directed coal mining safety research in Queensland, with particular impetus from explosions at Box Flat in 1972, Kianga in 1975 and Moura No 4 in 1986. Inquiries which identified the likely causes recommended measures and, research and two outcomes have been the present Mines Safety Research Advisory Committee and The Safety in Mines Testing and Research Station at Redbank, near Brisbane, dealing with all mining problems, coal and metalliferous. Already, important research into ignition and explosion and other health and safety matters has been accomplished; the Station has become an accredited testing laboratory; and international recognition has been achieved. Now the advisory, testing and research arms are soundly in place to pursue preventive investigations and be ready to provide assistance in any emergencies.

Jan 1, 1991

THIS tunnel, which is an adit 7000 ft. long, was undertaken by the Mount Lyell Mining and Railway Company Limited to connect its treatment works with the North Lyell mine at depth, with a view to effecting economies in transport and drainage. The work was carried out at high pressure throughout from both ends, and although the ground in the mine end was intensely hard, good progress was made, and driving was completed in less than fifteen months.The Mount Lyell mining field is situated in the west of Tasmania, about 20 miles inland, the only means of access being the Mount Lyell Mining and Railway Company's 3 ft. 6 in. gauge railway which connects with the Government railway system of the State at Strahan, on Macquarie Harbour. The region is mountainous, and presents many difficulties to the road and railway engineer. The West Coast range running north and south in a succession of bold prominences, which rise up to 4000 ft. above sea-level, forms the backbone of the district, and on its foothills the Mount Lyell mines are situated. The railway terminus at Queenstown...

Jan 1, 1929

It is a great honour to address our Institute as President, but the choice of a suitable subject was not an easy one. In the past when the presidential address was given at an annual conference the subject usually related to the conference or industry concerned; more recently the subjects have been more philosophical and this is a distinct advantage to me.I appreciate that I am addressing an informed audience and I am sure' that you are well advised in many of the points that I hope to leave with you. Unlike the specialist who gets to know more and more about less and less and eventually knows everything about nothing, I am one of the group who gets to know less and less about more and more and eventually knows nothing about everything.I hope you will appreciate this point whilst you are listening to me.In recent years I have been closely associated with the problem that troubles most governments of our time: the competition of many groups of differing backgrounds for the land that is available to the nation.This is of particular interest to the industry with which we are concerned as it is of critical importance to the discovery and development of future reserves of minerals and metals. Part of my daily task is involved with the administration of legislation for mining operations and the conditions under which such operations may be undertaken, in implementing government policies relating to mining, and in designing and administering legislationdirected to safety and health in mines.Most of our members are involved in exploration or in day-to-day problems associated with the production of minerals or the management of companies in these pursuits and would be aware of many of the conflicting viewpoints on priorities.F. F. Espie in his presidential address of 1975 'On being a minority', made the point that our Institute found that the mining industry had a great communication 'Problem with the Australian people.I believe that this is one of our major problems.

Jan 1, 1977

A continuous casting machine, of the Concast curved mould design casting billets in four strands, was commissioned at the Newcastle Works of The Broken Hill Proprietary Co. Ltd., in November, 1967. Quality assessment of early casts from this plant indicated that steel cleanliness was sometimes inferior to that of equival- ent ingot cast steel. Extensive trials to develop a modified deoxidation technique were not successful in improving clean- liness to the desired level. A "contra-flow" gas shroud, to cover the steel stream between the tundish and the mould, was developed, and proved successful in achieving the required levels of product cleanliness. The inclusion content of six grades of steel ranging in carbon content from 0.10 to 0.70 per cent is examined, and an attempt is made to explain theoretically some of the results obtained.

Jan 1, 1972

By C Rees, M Predebon, J Denney

It has been said on many occasions that æthe future of the mining industry of Australia, and indeed the world, lies in the hands of the studentsÆ. As a student, this can be a daunting, yet very exciting, statement. If nothing else, it is a direct challenge to the student body of the mining industry to take responsibility for its direction æafter 2000Æ. However, for the students to embrace this challenge, some responsibility must be borne by the universities and the industry itself to provide some direction and encouragement. Perhaps, therefore, the real challenge is to find the right balance between students, industry and education to best prepare the students for a career in the mining industry. The future industry will demand students who are capable and willing to adapt to change and technology and able to exert the vision and leadership required to ensure the mining industry continues to thrive well into the next century.

Jan 1, 2000

By R R. Lovel

In this paper, life cycle assessment methodology has been used to assess the variations in water use associated with different metal production and processing routes and provide insights into the value derived from water usage in the minerals sector. Using water consumption data derived from the literature it has been shown that the æcradle-to-gateÆ water consumption (or embodied water) for production of the various metals considered in the study ranged from 2.9 m3/t for steel up to 252 087 m3/t for gold. The results largely reflect the grade of the initial ore used to produce each metal, and can be approximated by the following equation:W = 167.7 G - 0.9039 where: W = embodied water (m3/t refined metal) G = grade of ore used to produce metal (per cent metal) The study showed that indirect water consumption in the metal production life cycle, in particular that due to electricity generation, can make a significant contribution to the embodied water value, eg aluminium production. When expressed in terms of m3/t ore, the results for all metals considered indicated that the embodied water is roughly, on average, three times the water consumption of the mining and concentration stage. It was also shown that the economic value per m3 of water consumed for the minerals industry exceeds that for the agricultural and industrial sectors, supporting the view that allocating water resources to the minerals industry has a strong underlying economic basis. Water reforms currently taking place in Australia aim to address issues such as competition for water access, reduced security of supply and increase in cost. Consequently the minerals industry, along with others, can be expected to come under increasing pressure to reduce fresh or raw water use and to integrate water use across sectors. While water recycling is an obvious candidate to help reduce water consumption in the minerals industry, issues such as water quality, among others, will influence the extent to which this can be achieved. In addition, wastewater volumes can be minimised using techniques such as pinch analysis to establish and use the minimum water requirement for the process. The use of dry or near-dry processing technologies, for which the demand for water is small or zero, may be a more radical solution to the water consumption problem; however, it is possible that the introduction of dry processing would bring with it a new set of problems, including dust.

Jan 1, 2006

Review of the mining legislation in New Zealand has coincided with a number of radical changes. These include a redirection of economic management towards a more open and competitive economy; major reform of the state sector aimed at greater efficiency, transparency and accountability; a new environmental administration; and a fundamental review of policy for management of natural and physical resources. These changes provide an opportunity to develop a consistent and coherent approach in the minerals and related statutes that will achieve objectives of economic efficiency, equity, practicability and good environmental management.

Jan 1, 1987

Transport infrastructure constitutes, since always, an essential link between regions, countries and continents, for economical, commercial and human purposes. Permanently growing mobility needs, which are encountered in the whole world, lead to a more and more clear necessity to increase and modernise these transport infrastructures, as well in quantity as in quality, for all transport modes, and for all what is able to be transported, from people to consumption goods and energy. With only very few exceptions, transport infrastructure achievements have for long been the concern of the sole public authorities, at the various levels, which put them, mostly free of charge or at very low cost, at the disposition of the user or the customer.

Jan 1, 1999

By Yao S, Wang P, Zhang C

The Zhilingtou Au-Ag deposit is situated in the eastern part of the complexly deformed and metamorphosed South China Caledonian Fold Belt. It consists of seven orebodies that are almost exclusively hosted by biotite plagioclase gneiss of the Precambrian Chencai Group. They form an apparent en echelon pattern in both cross-section and level plan. Three different ore types, based on mineralization textures, have been recognized within the Zhilingtou lode. These are Au-Ag-rich quartz veins, Au and Ag-bearing silicified rocks and Au-Ag-containing altered rocks with quartz stockworks. The mineralization is principally composed of electrum, argentite, pyrite and minor sphalerite, galena as well as traces of hessite and chalcopyrite plus a gangue assemblage of quartz, rhodonite, sericite and chlorite. Fluid inclusions related to Au-Ag mineralization yield a wide range of homogenization temperatures from 110 to 447¦C, with two distinctive peak values at 250-300¦C and 350-400¦C respectively. S30Si values of quartz veins and silicification from the three stages of mineralization range from -0.1 to -0.4%o. The mineralization at Zhilingtou is interpreted as forming by recirculated meteoric water extracting ore-forming elements from metamorphic rocks due to Mesozoic volcano-magmatic activity.

Jan 1, 1995

By Huajun W, Long LZ

The composition of fly ash and formation mechanism of cennospheres are introduced in this paper. The signification of using this potential new mineral processing resource is emphasised. The beneficiation properties of the components of fly ash, such as susceptibility, specific gravity, size, shape and flotability etc have been examined in detail. A technique was designed to process fly ash from the XiGaoJing power plant in Beijing, and a flowsheet is also presented. Flotabld cennospheres, magnetic beads, sinkable beads, carbon and advanced pozzolamics can be obtained as separate products through this flowsheet. It is emphasised that the beneficiation of fly ash is an efficient means of totally utilising the resource. Examination of the products show that they have good physico-chemical properties. Possible areas of their application are also Suggested.

Jan 1, 1993

By F Pavloudakis

The installation of on-line analysis systems in the open-pit mines of the Public Power Corporation SA (PPC, the state-owned electricity entity of Greece) is considered to be the key-parameter for performing improved quality control and blending/homogenisation of the produced lignite. In order to investigate the accuracy of these systems under the site-specific conditions of the Greek lignite deposits, a research project was carried out. This was necessary since there is lack of experience in using on-line analysers in mines that produce a fuel of such a poor and largely fluctuating quality. After thorough market research, a dual energy gamma ray transmission on-line ash analyser was installed in Kardia mine of Ptolemais û Amynteon Lignite Centre, which is located in West Macedonia, Greece. The initial results obtained after the realisation of a series of dual-comparison trials (ie using two series of reference values that allow three-way comparisons) pointed out several problems that obstacle the achievement of high accuracy on-line measurements. More specifically, the measurements obtained by the analyser were higher than the concentrations determined by the two laboratories when the ash content was lower than 12 per cent (in wet basis). On the contrary, when the ash content was higher than 12 per cent, the measurements of the on-line analyser were lower than the concentrations determined by the laboratories. In other words, the range of the measurements obtained by the analyser was narrower than that corresponding to the lab analyses results. Therefore, the use of this on-line analysis system under the site-specific operating conditions of Kardia mine does not guarantee improved quality control of the lignite fed to the mine-mouth located power plant. Most probable reasons that explain the above-mentioned problems are the following: The frequent and widely ranging fluctuations of the chemical and mineralogical composition of the lignite transported by the conveyor belt, especially as far as its calcium content is concerned. This result from the nature and the origin of the mineral matter co-excavated with the lignite, which varies from calcareous marls to sands and clays rich in aluminium and silica minerals. The fluctuations of the lignite quantity transported by the conveyor belt. The change of the linear concentration of iron contained in the fabric of different belt parts.

Jan 1, 2003

By Shibata Y, Shimizu R, Fukushima A

Kobe is divided by the Rokko Mountains, runn- ing from east to west. The southern section of Kobe is highly developed in contrast with the northern section, but big, new residential pro- jects like the Hokusetsu New Town and Hokushin New Town are steadily being developed. To handle future traffic between the two sections of the city, the double-tracked Hokushin Line, now under construction, will connect the Shin Kobe Station of the Kobe Municipal Transit (Kobe's subway system) to the Tanigami Station of the Kobe Electric Railway. The locations of Kobe city and Hokushin Line are shown in Fig.-1 and Fig.-2 respectively.

Jan 1, 1987

By J P. Richards, M D. Johnston

The Porgera gold mine, located in the highlands of Papua New Guinea, produced 7.7 Moz of gold between 1990 and 1998. Reserves are estimated to be 12 Moz of Au. The deposit is associated with 6 Ma-old mafic alkalic intrusions emplaced at shallow levels into unconsolidated Jurassic and Cretaceous sediments, where they caused the formation of peperites. The mineralisation consists of an earlier base-metal-sulphide-rich stage with sericite-carbonate alteration (stage I), and a later phase represented by quartz-roscoelite veins (stage II). New styles of mineralisation and alteration have been recognised at depth in association with stage I. They consist of the assemblages magnetite-chalcopyrite-pyrrhotite and biotite-actinolite-anhydrite respectively. In addition, the recent recognition of adularia in some stage II veins (with roscoelite) confirms the similarity of this style of mineralisation with other adularia-sericite or low-sulphidation epithermal deposits.

Jan 1, 1999

One of the major changes in the resource industry in the nineties has been the re-internationalisation of the industry. The history of the resource business has been one of companies from the developed world utilising the cash flows from their operations to explore and develop mines in less developed regions of the world. This resource development has progressively generated wealth and economic development, which in turn, has led to a new generation of exploration and mining projects. In South America, Chile had led the way in a mining resurgence, now closely followed by Argentina, Brazil, Venezuela and Peru. Although Chile has long had a significant copper mining industry, the pre-nationalisation phase was driven by American capital; the current phase has been spearheaded by R.T.Z. - B.H.P. at Escondida with Canadian junior companies, in particular, providing major speculative impetus. The Australian junior companies have not been significant in South America.

Jan 1, 1995

By A B. Bell

The health and in some cases survival of mineral exploration and mining companies is, in today's markets, more dependant than ever on the effective use of information technology. The need for speedy collection, organisation, maintenance and distribution of corporate and project information is a phenomenon that will continue to strengthen with market thirst.Geographic Information Systems (GIS) provide a medium for storage, maintenance and retrieval of data, and Internet Mapping adds a technology for effective distribution of that data. Combining these technologies can return benefits both fiscally and technically by reducing costs of ownership in IT infrastructure and increasing the efficiency and effectiveness of both internal and external information delivery.GIS and Internet Mapping technologies have reached a practical stanza in their evolution and will continue to develop as a key business tool in the natural resources sector.

Jan 1, 2002

Iron from the blast furnace constitutes the starting point in steel production and any increase that can be made in iron production will bring about important repercussions in a long line of processes. Coke constitutes a major item in furnace operation and consumption at the Port Kembla Works of Australian Iron & Steel Ltd. has been approximately 1,850 lb. per ton of iron produced on ore practice, or 3,000 tons per day.For many years coke quality has been subject to much criticism by furnace operators throughout the world, sometimes with little real grounds. Whatever the merits of previous arguments, and they were no doubt two-sided, the development of bigger furnaces has focused attention on coke strength. At the same time a decrease in the quantity of good quality coking coals available to many plants has stimulated research in this field.Extensive coke research has been carried out overseas, and in Australia the.B.H.P. Organization is now actively doing likewise in its Central Research Laboratories at Shortland near Newcastle, N.S.W., and works research groups at Newcastle and Port Kembla Steelworks. Similar work has been initiated in the beehive coking industry. Such work is in its infancy and this paper will outline the direction of the activities at Port Kembla rather than propound specific solutions.At Port Kembla good quality coking coals are readily available from the IIIawarra coalfield. The seams generally mined for coking are Bulli and Wongawilli and to a much smaller extent Tongarra. Characteristics of these coals appear in Table 1.

Jan 1, 1958

Comalco Limited has recently completed construction of a $50 million kaolin plant at the site of its bauxite mining and industrial minerals operations at Weipa. The plant will produce 100,000 tonnes per annum of coating grade kaolin for the paper industry.Comalco produced the first coating kaolin from the deposit in 1979 on a trial basis. Since then a variety of quality coating grades with specific particle ize distributions and brightness values have been prepared.Extensive drilling and bulk sampling of the deposit over eight years has shown that the orebody is large and of a high grade suitable for the production of premium quality coating kaolins.The processing plant technology was developed by Comalco in association with the European kaolin and equipment producer Amberger Kaolinwerke GmbH (AKW).The Weipa kaolin plant is the first of this size to be built in the Pacific Basin region and it will offer the region's paper-coating mills a stable and reliable source of high-quality kaolin, shipped from an established bulk loading port. The paper provides an overview of the development of the kaolin investment, the nature of the production process and details the project management procedure used for the design, construction and commissioning of the plant. Three areas of significant interest, the gas turbine fired pray dryer, the moving bridge shiploader and the use of aerobelt conveyors on the project are detailed.

Jan 1, 1988

The movements of the major continental cratons and the distribution of the principal tectonostratigraphic terranes are reviewed in the Circum-Pacific region during Phanerozoic time. It is concluded that major periods of orogeny and consolidation of accreted terranes in the Circum-Pacific region is best correlated with periods of advance of cratonic blocks over the Pacific Ocean basin combined with relative convergent to transpressive motions between the cratons and the Pacific Ocean plates. Continental collisions and collision of terranes with continental margins has not been a significant geodynamic process in Circum-Pacific tectonic evolution. The permanency of the Pacific Ocean basin throughout 500 MA is remarkable. It appears no continental block or large continental fragment has ever entered or crossed the Pacific Ocean basin since early Paleozoic time. This area where no continent has entered for 500 MA is almost coincident with the present Pacific Ocean basin and seems associated with the 25 to 100 meter geoid high which dominates the present-day figure of the Earth.

Jan 1, 1990

The earliest suggestions that some metallic ore deposits might have resulted from seafloor volcanic exhalation seem to have been those of Elie de Beaumont in 1847 and Henry de la Beche in 1851. In 1885 Tinoco, and Bouglise and Cumenge, independently investigating-.the manto copper deposits of the Boleo district of Baja California, proposed that these had formed on the seafloor by precipitation from "hydrothermal submarine emanations". Some twenty years later the Japanese geologists Kukuchi and Tsujimoto (1904) put forward the idea that the Kuroko ore- bodies were seafloor volcanic sinter deposits and in 1919 this was re-affirmed by Ohashi. In 1909 the English geologists Thomas and MacAllister postulated a similar origin for some of the gold deposits of Mount Morgan in Queensland. Between the wars the great European economic geologists Niggli and Schneiderhohn both clearly recognized a class of seafloor hydrothermal deposits. The idea rose again immediately after the Second World War in a very clear statement by Hegeman in 1948, which was followed by contributions by Ehrenberg and Kraume and their co-workers on the submarine volcanic origin of the Meggen and Rammelsberg orebodies in 1954 and 1955 respectively. In 1955 the present writer, quite unaware of early or contemporary work on volcanic exhalative ore deposits, proposed a volcanic sedimentary/diagenetic origin for the stratiform base metal ores of SE Australia. In doing so the writer emphasized the probable importance of island arc volcanism, suggested that some "metallogenetic regions" of ancient terrains were in fact old island arc systems, that the composition of the ores might be related to the composition of the associated volcanic rocks and that such ores would be tied to volcanic stratigraphy. Ideas on relations between volcanism and stratiform ore genesis have thus been evolving over.a period of some 140 years and, beginning with the observations on Baja California in 1882, work round the rim of the Pacific has made an important contribution over a period of more than 100 years.

Jan 1, 1987

By S Z. Petho

The South Deep surface shaft system is being sunk to a final depth of 2750 m below surface and on completion will be the deepest single drop shaft in the world. The shafts will intersect the target reef horizon at 2650 m below surface. In order to negate the requirement for a shaft pillar, which would be extremely large at this depth, the reef horizon in the vicinity of the intersection is currently being mined. A high quality crushed waste/classified tailings backfill is being placed in the longwall stoping panels around the shaft intersection area. This will limit closure and ride which following shaft reef intersection could have a detrimental effect on the long term shaft stability. This paper discusses underground instrumentation results and numerical modelling exercises carried out to confirm that the shaft system will be stable throughout the life of the mine. Instrumentation projects include closure and ride measured between backfill paddocks and haulage leveling exercises carried out to determine the far field rockmass response to mining with stiff backfill. Results from the numerical modelling exercises show good correlation with measured data. This indicates that a high degree of confidence can be placed in the model input parameters and consequently in the design of the shafts to ensure their long-term stability.

Jan 1, 1998