Search Documents

By Larkings RH

The high gas emissions associated with the depth of mining and very high coal extraction at some Australian Collieries have provided a need to investigate the influence of geological and mining conditions on levels of gassiness. The introduction of longwall extraction in particular is associated with complex strata control problems and quick changes in gassiness. To this stage of Australian coal mining, no standard method has been developed to predict the different levels of gassiness associated with the various geological and mining conditions; and the relationship between coal output and total methane make has not been established. For local conditions, with a large number of coal seams lying in close proximity to the working seam, the significant contribution of gas emissions from adjacent strata was expected, especially as strata relaxation occurred during longwall mining. This depends mainly on geological conditions, strata control and coal production. For the deepest of the B.H.P. Collieries in the Newcastle region, the relationship between coal output and total methane make has been investigated by systematic gas balance measurement during longwall extraction. The computer method of iteration was used to approximate the mathematical equation from the initial graphs of coal production versus quantity of methane in the ventilation system for various strata conditions. The angle of caving was established for local geological and mining conditions, for planning and design of the positions of cross measure boreholes.

Jan 1, 1986

By B Indraratna, A Dey

The surface geometry of a rock bolt plays a very important role in the rock/resin/bolt load transfer mechanism. Very little work has so far been reported on the influence of the bolt surface geometry on the bolt/resin interface failure mechanism. This paper examines the behaviour of bolt surface roughness under constant normal stiffness condition in the laboratory. To study the shear behaviour of the bolt/resin interface a series of shear tests with an initial normal stress between 0.1 to 7.5 MPa has been conducted on the flattened bolt surface of two most popular bolt types currently being used in Australia. Bolts with deeper ribs offered better shear resistance at low initial normal stress conditions whereas bolts with shallow and closer ribs offered better shear resistance at high normal stress conditions. The maximum dilation occurred at a shear displacement of 60 per cent of the rib spacing irrespective of the bolt type and depth of the rib.

Jan 1, 2000

By A F. Cropp, D J. Bradshaw, W R. Goodall

Mineralogy and critically the texture of both the ore and gangue phases are of paramount importance in the flotation recovery of copper from porphyry ores. Mineralogy and texture will define the theoretical grade recovery curve for a feed ore. Actual grade-recovery falling below this may be due to texture and gangue influences, whilst desired grade-recovery above this line will not be possible unless the characteristics of the feed are altered.This review discusses examples of porphyry copper deposits where process mineralogy has been used to characterise these textural and gangue influences on recovery by flotation. More specifically, the influence exerted by grain size, liberation, association and elemental distribution is explored. The implications of these on overall plant philosophy and operation are highlighted, along with the subsequent potential impact on recovery.CITATION:Cropp, A F, Goodall, W R and Bradshaw, D J, 2013. The influence of textural variation and gangue mineralogy on recovery of copper by flotation from porphyry ore - a review, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 279-292 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By E Kasai, T Nakamura, E Shibata

In the present study, formation of PCDD/Fs from carbon particles like æsootÆ, so called de novo synthesis, was experimentally simulated using the powder mixture of graphite and metallic chloride. Composite states of graphite and chloride particles were varied by the preliminary treatment, ie high-energy ball milling for different time or heating at different temperatures. These samples were subjected to the measurement of the rates of weight loss mainly due to the oxidation of carbon, the formation of absorbent organic chlorides (AOX) and the formation of PCDD/Fs at 300¦C. The amount of PCDD/Fs formation increased by applying certain pretreatments. Further, linear relationships were obtained among the formation rates of PCDD/Fs and AOX and the weight loss of sample. These results will give useful information to investigate the mechanism of PCDD/Fs formation from unburned combustible carbon and hydrocarbon in thermal processes.

Jan 1, 2002

The beneficiation of heavy metal oxides, such as iron ore, is usually performed with heavy medium separation in cyclones, static baths and lately with Larcodems. Atomized ferrosilicon is most suitable as a heavy medium at densities above 3600 kg/m3 whereas a mixture of milled and atomized ferrosilicon is suitable at densities below 3600 kg/m3. When operating a beneficiation plant at densities higher than 3600 kg/m3 the quality of the ferrosilicon particles is an important factor that influences the control of the beneficiation process. Therefore, it is important to know how the rheology would be affected by the ferrosilicon quality as it also influences the control of the process at these elevated densities.

Jan 1, 2002

By Hayes K. M, Ostwald J

Compacted tablets of hematite ore (containing clay and quartz gangue) and limestone were heated in air in an ULVAC-RIKO rapid heating furnace to maximum temperatures in the range 1200-1350°C.The resulting sintered products were examined in terms of mineralogy, texture, strength and reducibility. The sintered tablets are a good analogue of normal plant sinters. These investigations have shown that sinters of optimum reducibility are produced in the narrow temperature range 1250-l275°C. Conditions for the production of such highly reducible sinters under plant conditions are discussed.

Jan 1, 1984

By S Yang, J Wang, J G. Ning

A series of conventional dynamic uniaxial compression (CDUC) tests and coupled static-dynamic loading (CSDL) tests were conducted using a split Hopkinson pressure bar (SHPB) system to explore the dynamic mechanical behaviour and fracture characteristics of medium sandstone on a microscale in the laboratory. In the CDUC tests, the dynamic uniaxial compressive strength of the medium sandstone was rate-dependent, while the dynamic elastic modulus was not dependent on the strain rate. Then, we proposed a generalised model to characterise the rate-dependent strength from 17.5 s-1 to 96.8 s-1. In the CSDL tests, with increasing initial pre-static stress, the dynamic elastic modulus and dynamic strength increased nonlinearly at first and then decreased. The results show that two classical mechanical types (ie Class I and Class II) are observed from the dynamic stress-strain responses of the CDUC and CSDL tests. By means of scanning electron microscopy (SEM), the micro difference of post-loading microfracture characteristics in Class I and Class II behaviour was identified. In Class I behaviour, intergranular fracture (IF) usually initiates at or near the grains, most cracks deflected along the grain boundaries, resulting in a sharp angular edge, then coalesces to the main fracture surface that splits the specimen along the direction of stress wave propagation. In contrast, Class II behaviour results from the combined IF and transgranular fracture (TF).

Nov 29, 2022

By C B. Valentin

It is acknowledged that the analysis of iron ores using X-ray fluorescence (XRF) for major and minor elements is best carried out on fusion discs. This method of sample preparation eliminates mineral and particle size effects which can lead to biased results when using pressed powder pellets. However, the fusion disc method is costly as it requires a high capital investment in platinumware, requires experienced operators and uses expensive fluxes. Also, the dilution effect complicates the analysis of trace elements. For many applications, such as exploration and mining control, the method of XRF analysis of iron ores by pressed powder pellet probably provides data of adequate quality. Kumba Iron Ore, an iron ore producer in South Africa, recognises this and carries out most analyses of iron ore by pressed powder pellet and uses the automated fusion method mainly for certification of in-house calibration standards and quality control (QC) samples that are used for validation of pressed powder pellet method purposes. Automated fusion is also used for analysing the composite export shipping samples. All the other exploration, production, despatching and plant operation samples are done by the pressed powder pellet method. Automation of sample preparation procedures should improve the quality of data for pressed powder pellets. To compare the precision of the three methods of sample preparation and XRF analysis, 20 aliquots of a QC standard were prepared and analysed by each procedure/preparation method. The results and statistical data on the most important elements, Fe, K2O and P, are as shown later in Table 2.Clearly the precision is best for the auto prepared fusion discs, as expected, and worst for the manually prepared pressed powder pellets. However, the data generated from the auto prepared pressed powder pellets compare remarkably well against those from the auto prepared fusion discs.

Jan 1, 2007

As students progress further into a degree, the decision of vocation selection, and even more importantly û securing employment in a particular industry sector, can become quite daunting. However, with a little initiative, students can overcome these issues by not only researching what employment opportunities exist, but by applying for summer vacation employment. Undergraduate vacation employment, especially with a world-leading hydrometallurgy research organisation such as the Parker Centre, can dramatically alter a studentÆs perspective of particular industries and possibly even alter their selection of vocation pursuits upon graduating. Students can also use vacation employment to enhance their networking capabilities, technical skills and knowledge by dealing with challenging new topics such as sulfur dioxide leaching, which is also discussed in this article.

Jan 1, 2005

In the course of an investigation of the influence of bismuth on copper carried out some years ago, (1) the author found that phosphorus exerted a beneficial effect on bismuth-copper alloys of low bismuth and oxygen content by neutralizing the embrittling effect of the bismuth. In the intervening years, a further examination of bismuth-phosphorus-copper alloys has been canied out and the influence of other elements and combinations of elements on copper containing bismuth has been studied.The results recorded in the present paper are part of this investigation.MATERIALSAll the alloys were made from high-grade copper (KS.A. wire-bar) of the following composition: copper 99·95%, oxygen 0,040'%, iron 0·0015%, sulphur less than 0-001%, bismuth less than (j>'OOl%, other elements each less than O· 0010/<-. The bar was hot rolled and cold drawn to strip which was cut into short lengths and cleaned in nitric acid ready for melting.A piece of this 'strip was drawn to wire 0·08 in. diam., annealed at 5000 C, and measured for electrical conductivity as a check on purity. The result was 101·5% of the I.E'.C. standard.In making the alloys, phosphorus was added as 14% phosphor-copper, bismuth as 17% bismuth-copper, and the other constituents either as copper alloys or as elements of a high degree of purity.PREPARATIQN OF STRIPSThe charges were melted in plumbago crucibles (Morgan salamander brand) in an oil-fired furnace, Le;, in the manner commonly adopted in industrial practice. The copper was first melted under charcoal, well stirred with a chaned stick, and the necessary alloying elements added and stirred in with the stick. The weight of a charge varied according to requirements but generally was about 4 lb. The charges were poured into slightly tapered brass moulds heated to about 1000 C and dressed with a mixture of mineral oil and tallow. They were not only poured under charcoal through the burning mould dressing but also- through a ring of flame produced by burning kerosene on asbestos cord wrapped round the top of the mould. Experiments carried out with plain copper proved that by this means oxygen could be excluded from the stream of metal. The billets were 7·5 in. long x O·83 in. diam. x 1·3 lb. weight.The billets were cropped about 1 in. from the top, cleaned in nitric acid, and measured for density by the usual method of weighing in air and -in water. As these measurements were required only as a check on casting, technique a high degree of accuracy was not essential (accuracy = -+ 0·2%).

Jan 1, 1942

The location of the Inglewood Goldfield is 40 km north-west of Bendigo on the Calder Highway and covers an area of over 1600 hectares. The field was discovered during the 1850s gold rush and over 16 000 people camped on the field. Mining first began in 1859 and since then more than seven tonnes of gold has been removed from four major lines of reef. Most of the gold was won in the period between 1900 and 1940.. Goldquest NL currently has leases over approximately 1550 hectares and through its historical research has identified 142 known reefs.

Jan 1, 1993

Numerical simulation by a finite element computer code has bee* used to identify key stages in the initiation of confined bulk explosive by cast primers. The simulations have been verified by comparison with experimental field measurements of shock arrival time versus distance above the primer for a relatively sensitive emulsion doped with ammonium nitrate prills. Further simulations were performed examining the effect of primer size in a relatively insensitive blend of ANFO and emulsion. Immediately above the primers, changes in shock velocity in the explosive were caused by the interactions between shocks originating from different surfaces of the cylindrical primers. At a distance up the explosive column corresponding to about one to two borehole diameters, the arrival of shock reflections off the borehole walls caused a sudden acceleration up to the confined steady state detonation velocity. The simulations reproduced experimental observations that primer size has only a weak effect on changes of shock velocity with distance for confined explosives. However, it was predicted that primer size has a strong influence on the intensity and duration of the pressure pulses that bulk explosive send into the rock surrounding the primer region.

Jan 1, 1990

The initiation of cast Pentolite primers by detonating cord has been examined by the combination of two different experimental techniques with computer simulation by the finite element hydrodynamic code DYNA2D. In the first type of experiment, the cord/primer system was placed in a water aquarium, and photographed using a high-speed image converter camera. This highlighted the emergence of the detonation front through the primer surface and the generation of shock waves in the surround- ings. Numerical simulation was used to interpret the experimental record, establishing where the cord had induced buildup to detonation inside the primer. The second experiment used the plate dent test, where the primer was placed in contact with a block of metal (here aluminium), with the resul- tant dent in the metal surface being a measure of primer output. Detailed numerical simulation of this test confirmed that the observed dent was caused by the development of a complex series of shock waves inside the Primer.

Jan 1, 1988

By White A. H, Gillies A. D S

In recent years the Australian gold industry has gone through a major expansion phase. The need for finance has led to adoption of different approaches such as the well known gold loan, forward selling, equity participation by suppliers and equipment leasing. During early periods of the expansion, significant new equity was raised chiefly for high risk exploration ventures. The major form of new equity finance was ordinary shares, often in 'No Liability' companies. The increasing capital requirement of the huge new development projects of the 1980s also spurred the use of debt finance. This trend was accelerated as high inflation and the taxation advantages of debt finance made borrowing attractive. This paper reviews major financing techniques used by the Australian gold industry with particular emphasis on the innovative financing techniques initiated recently. An analysis has been undertaken of the effects on the industry of issues such gold loans, forward selling, equity participation by suppliers, fly-in fly-out operations, contractor mining and equipment leasing. In order to achieve a better understanding of the innovative financing techniques, a survey of already published financial data from well known Australian gold mines was carried out. Data was collected from various published financial reports of gold mining companies. In addition, a questionnaire survey was sent to gold mining companies to assist the collection of further information. The results of this study show that there are a significant number of gold mines variously using gold loans, forward sales, contractor mining and fly-in and fly-out arrangements to finance their projects. Only four operations have vendor suppliers investing capital funds in their projects. Based on the findings of this study, conclusions and recommendations are drawn that these approaches are likely to be with Australian gold industry for some time in the future and will continue to be intensively applied to finance gold projects.

Jan 1, 1994

In the 25 years since Broken Hill's 75th Anniversary which was marked by an Australasian Institute and Mining and Metallurgy Conference in Broken hill, there have been some significant changes in the role of mines inspectors. This paper updates the information given by the then Chief Inspector of Mines, J.H. Burford, to that 1968 Conference, with an emphasis being placed on mines inspection, although it also reflects changes to mining legislation and regulatory bodies.

Jan 1, 1983

By Kilgour I

The installation of a final cleaning column at Ok Tedi Mining Limited was carried out to increase final concentrate grade in order to reduce concentrate handling, shipping and treatment charges and to reduce penalty payments. To fast-track the project a decision was made to install a full-size column on one of the two parallel circuits, designed on information readily available and utilising the experience of mill staff and an engineering consultant, rather than delay installation while a pilot scale program was conducted. A 3.66 m diameter by 12.8 m high column was installed to produce 40 t/h of final concentrate from a combination of rougher concentrate and recleaner concentrate. The column design and sparger system were by Cominco Engineering Services Limited.

Jan 1, 1991

By Moyes A. J

The Intec Copper Process uses a strong chloride electrolyte at atmospheric pressure and 80 - 85¦C to produce high purity, 99.99 per cent copper granules and elemental sulphur. A recent, exhaustive study by an independent, major Australian corporation has shown the capital cost of an Inter plant to be approximately half that of a copper smelter at the 200 000 tpa capacity level and approximately half the operating and capital cost at the 50 000 tpa level. The Inter process costs were also shown to be greatly superior to the best available leach/SX/electrowin technology. The process utilises a multi-stage counter current leach at 80 - 85¦C with the addition of air at atmospheric pressure to precipitate iron as a goethite type compound, followed by a two-stage purification process separating impurities in metallic- and other forms. Purified cuprous chloride/sodium chloride solution is fed to an electrolytic diaphragm cell where high purity copper granules are produced at current densities of 1000 - 1500 A/m2 withoutthe need for conventional electrode stripping. Power consumption is approximately half that of the cupric route. The product is suitable for the direct powder metallurgical conversion of the granules to products such as wire or strip. All the steps in the 'furnace free' conversion of copper mineral to product have been demonstrated The process can treat low grade and contaminated concentrates without penalty, thereby offering greater returns to the miner. Lead, zinc and silver may be recovered as metals, with the high oxidation potential of the electrolyte allowing extraction of gold at high efficiency. The gold is selectively precipitated on activated carbon with negligible copper and silver contamination.

Jan 1, 1992

By N J. Welham

The Intec Copper Process is an environmentally advantageous hydrometallurgical process for the production of high purity copper and associated precious metals from copper sulphide concentrates. The process uses a mixed chloride-bromide lixiviant in an elegant cyclic circuit to leach the copper into solution, rejecting the iron as stable hematite rather than as unstable jarosite. After purification of the pregnant liquor, copper is electrowon at London Metal Exchange Grade A purity, while the anodic energy of the cell is stored as the soluble species, HalexTM, for recycle as the regenerated lixiviant to the leach circuit. Both gold and silver are leached and recovered directly from this cyclic process without resorting to cyanide leaching of the residue. No liquid emissions result from the Intec Copper Process, whilst spent air and water vapour from the leach are released to the atmosphere. The sulphur in the minerals reports to the solids residue in elemental form, without the need for expensive handling of voluminous gaseous sulphur dioxide streams found in smelters. A significant difference to competing smelting and hydrometallurgical processes is that any mercury entering the process from the sulphide concentrate feed is recovered rather than reporting directly to waste or polluting the environment. Outside the process circuit itself, the Intec Copper Process has several notable environmental advantages over competing technologies: Flexibility of scale with low capital and operating costs allow operation directly at the mill head at production rates as low as 15 000 tpa, significantly reducing environmental impacts from concentrates transport. The ability to handle low-grade and dirty concentrates often allows greater recoveries in the mill, improving both the economics and environmental acceptability of a mine by reducing metal losses to tailings. A comparison of the total energy requirements of the Intec Copper Process with those of competing technologies shows that the Intec Copper Process has the lowest energy consumption of any of the known hydrometallurgical processes, as well as improving upon pyrometallurgy under appropriate conditions.

Jan 1, 2002

By Rosengren KJ

Geotechnical conditions often have a critical influence on the design of new open pit and underground mines, but they are often considered of secondary importance in relation to other factors, such as detailed geology, orebody geometry and grade distribution. As a result, geotechnical studies may not be carried out during early project investigations or, at best, may be given only superficial attention, often to the overall detriment of the project. Technically and economically, it is logical that geotechnical studies should be integrated with geological investigations as soon as it becomes evident that the particular deposit may prove to be economic. The paper discusses the use of geotechnical information in the selection of mining methods and mine design for underground mines and for wall design and assessment of excavation characteristics in open pit mines. It then considers methods of obtaining the relevant data, with particular reference to exploration boreholes. Selected case studies on the application of geotechnical data to mine design are Included.

Jan 1, 1986

A mining operation can be identified as demonstrating prudent management when a number of vital characteristics are evident.All risks and opportunities that are critical to the on-going success of the operation have been identified and are being effectively managed. All significant tasks and events are plan driven. All levels of management visibly support the policies of the operation through their attitude, behaviour and actions as well as words. Supporting evidence for required activity and the outcomes is readily available. Improvement mechanisms are working to advance the key business processes. Everyone is working towards satisfying the needs of the stakeholders of the operation. When these characteristics are integrated with the satisfaction of all legislative requirements, all industry codes and optionally all relevant international management system standards then an operation is fulfilling all the requirements of a Due Diligence Process. The majority of mining operations do not show all of these characteristics and therefore unnecessarily suffer from missed profit opportunity and constant cost pressure, less than acceptable safety and health and environmental performance and consequent poor relations with employees, unions and regulators. In these operations the characteristics to be observed are quite different.Serious incidents are occurring with no sign of a rate decrease. The operation lurches from one panic ituation to another. Management are absent in their leadership, but very active in developing rules and enforcement methodologies. The operation has no history. Re-inventing the wheel with employees who come and go at an alarming rate seems to be forever occurring. All efforts are directed at controlling the business outputs with a strong emphasis on blame. Everyone is trying to look busy to avoid the ever-present cost reduction threats. To change to more prudent management utilising a Due Diligence Process is not theoretically difficult. However it does take clear direction, focussed efforts, supporting actions with appropriate tools and perhaps most importantly an internal desire and drive to become such an operation. A Due Diligence Process is about doing the important things that have to be done, providing the understanding of why they are important, demonstrating proof of activity and effectiveness, and leading the way through effective management.

Jan 1, 1998