Search Documents

By Mowat B. A

I lamata is within the Morobe Goldfield (7¦ 25' S, 146¦ 39' E) on the Wau (SB 55-14),1:250,000 scale map sheet (Fig 1). The deposit is 13 km SW of Wau, within the headwaters of the Upper Watut River, at an average elevation of 2000 m. The steep mountainous terrain is covered by dense tropical rainforest and access is by helicopter or by foot track. The deposit has been described previously by Wells and Young (1991) and 1)enwer. Leach and Mowat (1995). Data collected to late 1996 have been used to estimate an Inferred Resource of 9.2 Mt at 3.1 g/t gold using a cutoff of 0.5 g/t. This contains a high grade portion for which an Inferred Resource of 1.2 Mt at 9.7 grt gold has been estimated using a 5.0 g/t cutoff.

Jan 1, 1997

THIS paper deals with the handling of the various materials used in the 100-ton zinc plant at Risdon, and, in view of the magnitude of the works, the configuration of the ground covered by these works, the variety of the rnaterials used, and the large quantities, a very attractive and interesting subject is opened.The works are situated on the right bank of the River Derwent, about four miles above Hobart, the capital city of Tasmania. The Risdon works cover a space of 149 acres, the area being :3800 yards long by 2800 yards wide, and the elevations vary from 6 ft. above high-water mark at the wharf and foreshore to 163 ft. above high-water mark at the power station, these being the limiting points as regards elevation which are considered in this paper. Throughout the paper elevations are given in feet above high-water mark. Fig. 1 shows a general view of the works taken from the opposite bank of the River Derwent. The wharf is clearly shown, with SS Kekerangu loading residue; behind the wharf is seen the inclined conveyor leading to the cakine bin; further up the hill is the leaching division. No. 1 haulage runs to the left of this up to a point on the left of the power station, the large reinforced concrete building at the top of the hill. Below this is the cell room, the largest building on the plant. The roasting division, not very clearly seen, lies at the foot of the main stack, and the casting division lies to the left of this, between the leaching division and the cell room. A large wharf has been construl'ted alongside the works. This wharf is 880 ft. long and 60 ft. wide. It is capable of berthing large overseas steamers, as at low tide there is a depth of :30 ft. of water. The rise and fall of the tide at the wharf is 4 ft. 6in., and the river is navigable at all states of the tide. Just above the company's wharf...

Jan 1, 1923

The Harmonious Design on the Beneficiability for the Pt-Pd Ores Containing High MgO Gangue in Yunnan

Sep 13, 2010

Hatches Creek has been inactive since 1961, but with better metal prices, interest in the field is reviving.The mixed gravity concentrates which were unsalable in 1951 have been experimentally separated into salable wolfram, scheelite, and bismuth-gold concentrates, and a flow sheet incorporating magneticseparation and flotation has been developed.

Jan 1, 1965

Current NSW Government policy requires searching for more than just minerals during an exploration program û add endangered fauna and archaeological relics for a start.

Jan 1, 1995

Current NSW Government policy requires searching for more than just minerals during an exploration program - add endangered fauna and archaeological relics for a start.

Jan 1, 1995

The need for legislative reform of health and safety legislation has been recognised in New Zealand for about a decade. Previous legislation did not cover all work places, many areas were excluded from coverage, and there were at least 14 different acts and dozens of sets of regulations dealing with various aspects of health and safety.

Jan 1, 1993

By Okabe K

Development in the theory and practice of hearth drainage is reviewed. Difficulties in the hearth drainage were re- newed during late sixties and early seventies when the size of a blast furnace and the top pressure were increased to result in the increase in tapping rate. Hearth drainage was improved first by in- creased number of tapping and then decreased tapping rate as it was predicted by theoretical studies. State of the coke bed in the hearth, e.g., 'floating' or 'sitting-on' the hearth bottom, is discussed in relation with influential factors on it and its influence on the furnace operation. The 'sitting-on' coke bed is to be aimed at for the consistent furnace working and for the lower rate of erosion of the hearth refractory. As the continuous tapping became standard prac- tice in large blast furnaces, the interest in the basic research renewed. Prospect of the further research including mathematical modelling of the hearth drainage is discussed.

Jan 1, 1981

The Heavy Media Separation plant operated at Lidsdale siding, eight miles from Lithgow, by the N.S.W. Mining Co. is a product of the Western Machinery Company, of D.S.A.This mill, designed to use finely ground magnetite as the heavy medium, was prefabricated in America and shipped to Australia for erection.First operated early in December, 1951 it has worked on a two-shift basis since. Designed for an input rate of 330 tons per hour, this mill is capable of washing 4 in. x /u in. coal down to its inherent ash by removing all heavy material, including high-ash coal.The principle is quite simple. A stream of raw coal is fed into the separatory vessel which contains a liquid medium, the density of which is adjusted to produce the desired split between coal and refuse. In this bath the lightest coal floats, and all material heavier than the specific gravity of the medium sinks, and is removed separately. Such a system is,. ideally suited to Western coal, as there is no definite splitting point between coal and refuse. Inherent ash of the coal fed to the plant ranges from 8 to 25%, the corresponding density range being from 1.28 up to 1.8.Generally speaking, the higher the density the higher the ash content of the coal.The density in the separatory vessel (hereafter called the cone) can be quickly and easily adjusted throughout the above range to any desired value. Customer requirements, coupled with the economics of washing, dictate the proper specific gravity to be maintained. At present this is held at 1.52...

Jan 1, 1954

For its Hellyer project, Aberfoyle sought to establish a high degree of confidence in all aspects of the feasibility study. Accurate capital and operating cost estimates were an integral and essential part of the study. They were crucial to the evaluation of investment returns and competitive cost position. Both the capital and operating cost estimates were based on the comprehensive data available from exploratory mine development, pilot plant operation, detailed engineering design, and Aberfoyle's experience in the area. One of the principal project objectives was to maximise operating productivity and efficiencies and this created capital cost alternatives which needed thorough cost-benefit assessment. The estimated capital cost for construction and development was $90 million, and the project was completed virtually on time for $80 million. The first year's experience indicated that operating costs would settle to well within 10% of the estimates.

Jan 1, 1990

The ore deposits investigated are composed primarily of hcmatite and can be grouped into three categories depending on the amount of leaching of silica and carbonate which has occurred from the original iron formation, and on the amount of recrystallization of the hematite. Minor constituents are magnetite. goethite, and quartz.Texturally. there are five different types of hematite, formed at different stages during the genesis of the ores.These are1. anhedral hematite grains formed by recrystallization of hematite already present in the original iron formation.2. hematite formed by martitization of euhedral magnetite, 3. massive aggregates of fine- to medium-grain hematite formed by recrystallization of (l) and (2).4. tabular or prismatic hematite grains occurring around the boundaries of the massive aggregates or martite euhedra. and in fractures and5. specular hematite. which is present in fractures in ore types (l) to (4).Minor and trace-element analyses, determined using an electron-probe microanalyser. indicated that only silica (less than 0·01 per cent) and cobalt (less than 0·002 per cent) were present in the magnetite and hematite from unaltered iron formation and in the hematite from the ores. Low concentrations of trace elements are typical of magnetite in ores formed as marine precipitates. On the basis of the analyses alone. it proved impossible to distinguish between the five hematite types. A determination of the variation in rare-earth trace element contents between iron oxides in the iron formation and iron oxides in the ores indicates that the rare earths were depleted during ore formation. A possible explanation is that they were removed in solution with silica as it was leached from the iron formation.

Jan 1, 1971

Goldfields (Tasmania) Limited operates a small, high-grade underground gold mine on the West Coast of Tasmania, 30 kilometres north of Queenstown. The main orebody, Zone 96, was discovered in 1989, with major development work commencing in 1993. The mine was officially opened in July, 1996. Initial production came from a shallow orebody known as the Sill Zone, some 50 - 150 m below surface, which was accessed by a 1 in 8 decline. Zone 96 lies between 350 m and 550 m below the surface and is accessed by a 402 m deep, 3.2 m diameter internal shaft from the collar level located 100 m below surface. The main ore extraction system in Zone 96 is mechanised cut and fill, using high density paste fill. Run of mine ore and waste are hoisted in a single 5.5 tonne overturning skip, then trucked from the underground collar to the gold plant ROM pad or waste dump, respectively. Ground conditions in the mine vary with orientation and proximity to major faults. The gold is contained in a sequence of strongly altered volcanic rocks adjacent to the Henty Fault. Most of the gold is contained in massive quartz, ranging in width from 0.5 m to 7 m, which has been subjected to substantial faulting. Average mineable grade is about 27 grams gold per tonne. Ore reserves in 1996 proved an initial mine life of approximately 4.5 years at 90 000 ounces gold per annum, with significant potential for additional resources from extensions to Zone 96 and adjacent zones. The lease is located in an environmentally sensitive area and a very high standard of environmental management is an essential part of the operation. This paper describes the relevant aspects of mining at Henty including grade control, ground support, backfill placement and environmental management.

Jan 1, 1998

By K Sherry, N Shahbazi

Scope 3 emissions are a set of often overlooked indirect greenhouse gas emissions within a company’s value chain and represent the majority of emissions for many sectors. These emissions arise from activities conducted by entities beyond the reporting organisation’s ownership or direct control and are often challenging to calculate. Scope 3 emissions typically encompass purchasing goods and services, transportation and distribution, managing operational waste, downstream processing and utilising sold products. Within the mining sector, scope 3 emissions often constitute a significant portion of the overall carbon footprint. Therefore, these emissions are a significant aspect of the future of sustainable mining. As the journey towards a world committed to achieving Net Zero Emissions has started, the time to spark a transformative conversation in the mining industry has arrived. Consequently, a better knowledge of scope 3 footprints allows organisations to assess their emission mitigation projects against the total carbon impact of their operations and products.

Sep 1, 2024

By Fukui M

An increase in pig iron output by 50 per cent was aimed at after re-lining No.2 blast furnace of NAKAYAMA STEEL WORKS. This had to be achieved by increasing both the furnace volume (from 673 to 757 m3) and its productivity, Without equipment for high top pressure operation, high productivity was mainly attained by the following three measures; (1) improving the gas flow characteristics by maintaining a high ratio of agglomerated ores, increasing the strength of sinter and coke, and optimizing the charge distribution, (2) decreasing the fuel ratio by low Si operation and the use of hot blast, and (3) oxygen enrichment. In addition, the tapping controls for pig iron and slag were intensified. As a result of the above measures an excellent hot metal output of 2.7 tonne/m3/day was attained in April 1979 (monthly average).

Jan 1, 1980

By B Roach, P M. Ashley, B Hooper

Mineral occurrences of the Hillgrove Au-Sb-W district are hosted in late Palaeozoic polydeformed, hornfelsed metasediments and Permo-Carboniferous granitoids of the NewEngland Orogen. In excess of 204 individual occurrences have been identified to date with the mineralisation developed as strike extensive (>20 km of known veining) and potentially depth extensive steeply dipping fissures. These are contained within an elongate area measuring some 9 km by 6 km in surface dimensions. Recorded gold production of 720 000 ounces along with current resources in the order of 340 000 ounces highlight the significance of this district. Historical antimony production is estimated at in excess of 50 000 metric tonnes. Significant tungsten of over 2000 t in the form of scheelite has also been produced from the field. Mineralisation is developed in veins, vein breccias, sheeted veins, network stockworks and as alteration sulfide haloes to the main structures. The vast majority of fissures are subvertical and vary in widths of up to 20 m in places. Paragenetic studies have previously indicated that the earliest mineralising event was a scheelite-bearing phase of quartz veining. Subsequent phases of arsenopyrite-pyrite-quartz-carbonate veining were accompanied by gold and minor base metal sulfides. Alteration is typically sericite-ankerite-quartz. Overprinting stibnite-quartz veining with gold-electrum, aurostibite and arsenopyrite form an important subsequent phase. Veining can be inferred from historical records to extend for vertical depths of over 1 km.

Jan 1, 2004

By Ibaragi K

High grade ores were intersected in 1981 by a scout drill carried out by the Metal Mining Agency of Japan during a reconnaissance dril ling programme. The original aim of the hole was to explore a deep target where geophysical anczralies overlapped the abandoned old drifts (gravity- high, resistivity-low by airborne EM, and resistivity-low near the surface and high at depth by Schlumberger deep sounding). Subsequently, a follow-up drilling programm was commenced by the Sumitcrro Metal Mining Co Ltd, and all the 18 holes intersected high grade ores. The resources were then "guestimated" to contain ca.120 tonnes gold with an average grade of 80g/t Au between -40m and +120n a.s.l. The underground development was started in December 1982 and the first crosscut intersected the ore body at 100m level (a.s.l.) in July 1985.

Jan 1, 1987

The development of the lower Hunter Valley, centred around Newcastle and its suburbs is closely linked to the mining of coal and the settlements which grew to house the colliery officials, the miners and their families. The Port of Newcastle expanded and developed as a port exporting coal to many ports of the world ranging from Hawaii and Brazil to Japan and Korea. The coal which passed through the Port of Newcastle, depend- ing on the historical period in question may have been mined in Newcastle itself, or one of the nearby colliery townships such as Lambton, Wallsend, Charlestown or Hamilton, or from one of the estuarine collieries located at Carrington or Stockton or from the West Wallsend area or from East Greta, Pelaw Main or Cess- nock located on the South Maitland (Greta) coal field or from the open cut and underground mines of the Singleton Coal District.

Jan 1, 1988

By J R. Leeming

Mines require ventilation to ensure an adequate atmosphere for the sustenance of life, and to dilute, render harmless and remove contaminants.This paper describes the developments in the United Kingdom (UK) from natural ventilation, through the introduction of fire and simple fans, to modern fully independent and remotely monitored and controlled installations.CITATION:Leeming, J R, 2017. The history of mine ventilation in the United Kingdom, in Proceedings Australian Mine Vent Conference 2017, pp 271–276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By J S-L Chan, J C. T Chu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. In its industrial days, Hong Kong’s mining industry was thriving, benefitting from the mineral occurrences that are related to the regional Mesozoic igneous and hydrothermal activities.Hong Kong was unique in the mining sector as it was so small in landmass but with such a rich variety of commodities discovered. There are records of commercial exploitation of tungsten, iron, lead, silver, beryl, graphite, quartz, feldspar and kaolin in Hong Kong before 1981. Of these, most of them are located in the New Territories.The Lin Ma Hang lead mine was operated in the 19th century by the Portuguese and was abandoned in 1958. The Needle Hill tungsten deposit was discovered in 1935 during construction of the Jubilee Reservoir. The Ma On Shan iron mine, which operated for 70 years between 1906 and 1976, was the largest mine in the history of Hong Kong. The Mui Wo lead-silver mine on Lantau Island can be traced back to the Ming Dynasty 400 years ago. West Brother Island, which extracted graphite from 1952 to 1973, was levelled in the 1990s to make way for the development of the airport at Chek Lap Kok.Nowadays, these mines are disused and abandoned, but this extended abstract reviews the legacy of the mining industry in Hong Kong to understand the impact that it had on techniques, the economy and culture.CITATION:Chu, J C T and Chan, J S-L, 2015. The history of mining in Hong Kong , in Proceedings PACRIM 2015 Congress, pp 109–114 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Glasson K. R

The history of Ore Reserve classification and reporting in Australia is largely a history of the Australian mining industry itself. In the late 1800s, when the industry was dominated by small scale, high grade underground mines, Reserves (if estimated) were based on hand sampling and geological inference, and reporting of Reserves was either non-existent or of extremely variable quality. By the mid-20th century, the industry was dominated by large underground base metal and gold mines. Reserve estimation was coming under the control of skilled geologists and mining engineers, however Reserve classification and reporting standards continued to vary in type and quality from mine to mine. Today, large scale, low grade mining operations predominate, and Reserve estimates are generally based on extensive drilling results processed (with geological control) by computer. Through the efforts of a Joint Committee established by The Australasian Institute of Mining and Metallurgy and Australian Mining Industry Council, Reserve and Resource classification and public reporting has been standardised and controlled by adoption of the ""Australasian Code for the Reporting of Identified Mineral Resources and Ore Reserves"" released in 1989. The Code, which will continue to be modified and improved by the Joint Committee, has also been used as a basis for guides to reporting in other countries, and there is now some hope that this difficult and vexing topic may finally become subject to international standards and controls.

Jan 1, 1992