Search Documents

By F. L. Wolf, A. A. Grubb

The tests here described were rrlade to obtain information regarding costs, efficiency, etc. of baking cores in an oil-fired oven and two electric ovens, which were installed, early in 1920, in the core room of The Ohio Brass Co. and were used almost continuously during the rest of that year. Operating costs were rather high so a complete test was undertaken early in 1921. The ovens will be referred to as Nos. 1, 2, and 3. Nos. 1 and 2 are electric ovens of different makes while No. 3 is an oil-fired oven made by the firm that made No. 2. The three arc. equipped with similar ventilating devices. They have full-height doors at front and rear. The cores are placed on iron racks, which arc lifted by Cowan trucks and rolled into the ovens through the front doors. When baked, they are removed through the rear doors. Fig. 1 shows the general plan of the elecric ovens while Fig. 2 shows the plan of the oil-fired oven. Oven No. 1 is 91 in. (231 em.) wide, 83 in. (210 em.) high. and 79 in. (200 cm.) deep, inside measurements. The walls are constructed ill panels about 18 in. (46 cm.) wide and 43/16 in. (10.6 em.) thick, packed with blocks of insulating material and covered with sheet iron. Thc concrete floor oil which the owns set is 13 in. (33 cm.) thick. 4 recess about 5 in. (13 cm.) deep was cut in the floor to provide room for the heating units. Channels and plates supported on I beams serve as supports for the trucks and racks. The ventilating system consists of a Sirroco No. 11/2 fan, connected so as to draw air from the top of the oven or from the room, through damper C, and to deliver it either to the bottom of the oven or to the floor; the delivery is controlled by the vane A. The fan 2nd pipes are covered with 1/4-in. (6.3 mm.) asbestos-cement lagging. The heating units have a capacity of 91.4 kw. and arc located along

Jan 1, 1923

By H. A. Schwartz

From time to time, one of the authors has had occasion to investigate the graphitizing reaction and has published the results mainly as discussion' of the work of other investigators. In view, therefore, of the diversity of both observations and interpretation, it seemed well to attempt, a revision of the entire subject in the Research Laboratory of the National Malleable Castings Co. The work consisted of a careful study of a single, impure, iron-carbon alloy. The material, which may be considered typical low-carbon white cast iron of the malleable industry, was an air-furnace iron of the following composit,ion: carbon 2.30 per cent., silicon 1.20 per cent., manganese 0.29 per cent., phosphorus 0.156 per cent., sulfur 0.048 per cent. The freezing range extended from 1213' to 1132' C., the latter figure agreeing with Gontermann's data.2 We have attempted to define the equilibrium diagram of this alloy, in the stable condition as related to the mctastable diagr,aui,- from a temperature somewhat below the euteetic freezing point to a temperature l>clow Arl and for a graphitic-carbon content from practically notliing to the original total rarbon of the specimen (see Fig. 6). More csp~c~ially we desired to locate the line in the stable diagra~n corrcspo~idi~lg to thc Ac, line of the metastable syst,ern, which is designated by analogy, thc At, line (t, from tcrnpcr carbon); also to dctermirle the locat'ion of A tm witah respect, to Acm t,o~vard their lowcr extremities at Arl in ordei to determine whether or not graphitization is completed by th~ separation of an iron-carbon entectoid analogous to pearlite in the iron-cementite system. This would involvc furthcr a colnparison of thc locations of Ihc stablc and met.astable 41 points. As the carbon concelltrations of thc solid solutions of the two syste~~ls are probably not, identical, an explanation of t>lieir differences and of thc,

Jan 1, 1923

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 ROBERY W HUNT 1883 JAMES C, BAYLES 1884-1885 ROBERT H RICHARDS 1886 THOMAS EGLESTON 1887 WILLIAM B POTTER 1888 RICHARD PEARCE 1889 ADAM S HEWITT 1890 JOHN BIRKINBINE 1891-1892

Jan 1, 1923

By Ancel St. John

Defects in the interior of metal objects are troublesome to both manufacturer and user. For the former, they frequently increase manufacturing cost through the rejection of material when defects appear after considerable work has been done. For the latter, they often cause damage to equipment, personal injury, or loss of life when a part, which has passed all inspections and has been put in service, gives way because of a hidden flaw. Methods of testing that locate such flaws without subjecting the specimen to possible, if not actual, destl-uction are few; x-ray examination, whether fluoroscopic or radiographic, is one. Hitherto, however, x-ray examination has been restricted to objects of nearly uniform thickness and regular outline; the inspection of such articles as those shown in Fig. 1 has been inconvenient and unsatisfactory. This figure represents a group of 5/16-in. hexagonal-head machine bolts,

Jan 1, 1923

1-Iron and Steel JOHN A MATHEWS, Chairman RALPH H SWEETER, Vice-Chairman WILLIAM CAMPBELL, Vice-Chairman MAX ROESLER, Secretary Iron Ore CHARLES B MURRAY, Chairman R C ALLEN W O HOTCHKISS MAX ROESLER ERNEST F BURCHARD WILLIAM KELLY DWIGHT E WOODBRIDGE M M DUNCAN CHARLES F RAND CARL ZAPFFE C T FAIRBAIRN THOMAS T READ Blast Furnace WALTER MATHESIUS, Chairman WILLIAM H BLAUVELT P KINNEY C SNELLING ROBINSON A J BOYNTON DORSEY A LYON H SWEETSEP D T CROXTON RICHARD MCCAFFERY R J WYSOR THOMAS L JOSEPH CHARLES P PERIN

Jan 1, 1923

PROF RICHARD ÅKERMAN Stockholm, Sweden DR FRANK DAWSON ADAMS Montreal, Canada ANDREW CARNEGIR New York, N.Y. PROF HATON DE LA GOUPILLIERE Paris, France SIR ROBERT A. HADFEILD London, England HERBERT C. HOOVER Leoben, Austria JAMES FURMAN KEMP New York, N.Y. PROF HENRI LOUIS LE CHATELIER Paris France EZEQUIEL ORDONEZ Mexico City, Mexico ALEXANDRE, POURCEL Paris, France PROF RICHARD H, RICHARDS Boston Mass. JOHN E. STEAD Middlesborugh, England PROF DIMITRY CONSTANTIN TSCHERNOFF St Petersburg, Russia PROF TSUNASHIRO WADA Tokyo, Japan CHARLES D WALCOT Washingtion D.C.

Jan 1, 1923

?ADAIR, ARTHUR C., Corp 4th Co., 1st. Training Bat., 154th Depot Brigade. ADAMS, HENRY, Major: Chemical Warfare Service. ARLUCK, A. A Headquarters, 1st Corps of Artillery. ASKIN, THOMAS B. H Ensign. BANKS, H. R., 2d Lieut Canadian Engineers. BAYLESS, G. E. S Supply Dept. U. S. Submarine Base. BELL, L. R Co. C, 302d Engineers. BELLIS, ARTHUR E., Capt Ordnance Reserve Corps. I BIRRETT, HOWARD, Lieut., Aviation Section, U. S. Signal Corps, Ellington Field. BOISE, PAUL T 2d Regiment, 24th Squadron. ?BRADLEY, CLARENCE I Convois Automobile Section 585. BROWN, GEORGE M Co. G lot Engineer Replacement Regiment. BUCKINGHAM, ALBERT U. S. S. " Coronet," S. P. 194, Section Base No. 7. BURNS J. J Co. 1-B, E. R. O. T. C. BURT, Co. B, let Engineers Replacement Regiment. ||BYERS, WHEATON B., 2d Lieut Ordnance Dept. CANTON, WILLIAM R., Sgt Headquarters Co., 80th F. A. CARSON, JOSEPH A., Capt A.S. S. R. C.' CHAPMAN, LEWIS C. Corp 29th engineers. CHETNEY, P. C., 2d Lieut 15th Bat. Headquarters Co. CHEVRILLON Louis French Red Cross. CHIDESTER, W. B., 1st Lieut 24th Machine Gun Bat. CHURCH, JOHN L., Capt 308th Engineers. CLAGHORN, D. MONTGOMERY, 1st Lieut 45th Engineers. CLAQHORN, JAMES L., Lieut Aviation Section, Signal Corps. CLARKE, ALEXANDER F U. S. Naval Aviation Service. COMINS, WALDO H. Ca t 41st Co., 164th Depot Brigade. COOK, FREDERICK A., Capt., Engineer Reserve Corps, Asst. to Div. Engr. 79th Division. COOPER, CLAUDE H. Capt C. A. R. C., 50th Artillery. COPELAND, N. R., Lieut. ||CORBY H.. G., 1st Lieut Co. D, 109th Supply Train. CORSA, BEAN, Capt Co. D, 612th Engineers. CORTESE, EMILIO Italian Army. COULDREY PAUL S., Corp British Expeditionary Forces. || CRAGIN, RODNEY S Co. E, 115th Engineers. CURRIE, JOHN M., Ca t Royal Engineers. || CUTTING, G. W., 2d Lieut U. S. Reserves, Field Artillery. V DARRINGTON, PAUL N., 1st Lieut U. S. Infantry. DAVIS, ANGUS W., Lieut-Col British Expeditionary Forces. || DAVIS, THORNTON, 1st Lieut 13th Field Artillery. ELAND, FREDERICK A., Major Engineer Reserve Corps. DOUGLAS, JAMES $ American Red Cross. DOVE, D. R., Candidate 21st Training Battery, F. A. C. O. T. C. Dover JAMES J 6th Co. C. B. DOWS, DAVID,Capt Coast Artillery, Officers Reserve Corps. || DRAKE, M. 6., 2d Lieut Headquarters Co., 325th Infantry. I || EMMERSON, E. Roy British Navy. EVERIT, RICHARD STURTEVANT Heavy Artillery Officers' Training Camp.

Jan 1, 1923

WHERE "MINING AND METALLURGY" OR THE TRANSACTIONS MAY BE CONSULTED For the convenience of members who may be traveling from place to place, the Secretary has compiled a list of libraries or other places in the United States and foreign countries where MINING AND METALLURGY or the Transactions may be consulted This list will be sent to members if they so request

Jan 1, 1923

TO THE, BOARD OF DIRECTORS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen -The following report covers briefly some of the more important activities of the Institute during the year 1923. In my report for the year 1922, I drew attention to the falling off in membership of the Institute due to the depressed condition of the mining industry in several lines and the inability of many of our members to find profitable employment in mining or its associated branches. A number who were unemployed during 1922 established connections during 1923, but a still greater number have been forced to resign or drop their membership during 1923 Fortunately, the number dropped is not so great as in the previous year. The Employment Service conducted by, the four Founder Societies bears witness to the trend in business For the young men just out of college, there are plenty of opportunities at small salaries, there are plenty of opportunities for them as laborers; but for the mature members, those of experience, there are few calls During the last eighteen months, our Employment Service has been able to place only six of our members out of every hundred engineers for whom it has found work. Another loss which this Society has suffered, but which is not felt so keenly by our sister societies, is in its foreign members. The A. I M. E. has always had a large foreign membership, but of recent years exchange has been so heavily against many European and South American coun¬tries that a large number of members residing abroad have been compelled to relinquish their membership Almost invariably these members express keen regret because of the necessity that confronts them, and almost invariably the writers express hope that present conditions will not last long and that they will soon be able to ask for reinstatement. Having stated the darkest side of the picture first, it may now be drawn to your attention that in spite of these losses the number of persons applying for membership was decidedly encouraging. From the quality point of view, the membership has not gone back¬ward The Membership Committee has declined to recommend many

Jan 1, 1923

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3

Jan 1, 1923

Executive A. R. LEDOUX, Chairman GEORGE D. BARRON SIDNEY J. JENNINGS J. V. N. DORR J. E. JOHNSON, JR.¬ Membership J. E. JOHNSON, JR., Chairman KARL EILERS F. F. SHARPLESS R. M. RAYMOND LEWIS W. FRANCIS Finance J. V. N. DORR, Chairman CHARLES F. RAND J. V. W. REYNDERS Library E. GYBBON SPILSBURY,' Chairman ALEXANDER C. HUMPHREYS GEORGE C. STONE' JOHN H. JANEWAY BRADLEY STOUGHTON Papers and Publications BRADLEY STOUGHTON, Chairman

Jan 1, 1923

By Charles Y. Clayton

The shank, to give good service, should not upset nor should it cause excessive wear on the various parts of the machine. To fulfill these requirements, the steel must have a certain hardness—that is, resistance to deformation. The hardness is expressed in conventional terms, as Brinell or scleroscope number. Before deciding on the hardness that is proper, several factors should be considered; the most important are: type of drill steel used (whether hollow or solid), length of steel, nature of ground, air pressure, and hardness of hammer or anvil block (usually 600 Brinell). These are not all, but they are the most cogent ones. Without doubt, it would be better to use a shank that is too soft than one that is too hard. Most satisfactory service will be obtained from shanks that are just hard enough to resist any tendency to upset. To express the proper hardness in terms of Brinell numbers would mean a great many tests over a long period of time, or a study of drill steels that are being used successfully in the various districts. To obtain some information along this line, the persons making this investigation requested, a number of companies to send to them drill shanks that had been given the usual treatment at that mine. The results of the hardness tests are given in Table 1. The hardness values given in Table 2 are those of shanks known to have been quenched in water and drawn. These results show that where water quenching and drawing are in vogue the hardness is rarely under 400 Brinell.

Jan 1, 1923

YEAR OF ELECTION 1913 FRANK DAWSON ADAMS Montreal, Canada. 1921. WILLIAM CUTHBERT BLACKETT Sacriston, Durham, England. 1923. GELASIO CAETANI Rome, Italy 1920. HENRY STURGIS DRINKER Merlon Station, Pa 1921. FERDINAND FOCH Paris, France 1922. FEDERICO GIOLITTI Torino, Italy 1906. SIR ROBERT A. HADFIELD London, England. 1921. FRANK WILLIAM HARBORD London, England 1917. HERBERT HOOVER Washington, D. C 1905 HENRI LECHATELIER Paris, France 1921. C. MCDERMID London, England 1913. EZEQUIEL ORDONEZ Mexico City, Mexico 1909. ALEXANDRE POURCEL Paris, France. 1911. ROBERT H. RICHARDS Cambridge, Mass 1891. DR. ING. H. C. EMIL SCHROEDTER Mehlem a Rhein, Germany.

Jan 1, 1923

By Wilder D. Bancroft

It is eight years since I have been connected actively with metallography, but in this time I have been learning something about colloid chemistry, which may be considered as the chemistry of bubbles, drops, grains, filaments, and films, all things in which at least one dimension is very small or in which the surface is large relatively to the mass. Films, of course, suggest to the metallographist Beilby's amorphous film theory, about which I am going to speak for a while, though probably not in the way you expect. I come to bury Beilby, not to praise him. So far as I can judge from looking over the literature hastily, there are two schools in the United States, those who accept Beilby's theory willingly and those who accept it unwillingly. Hoytl says that: At present there seem to be two schools in metallography, one which has adopted the amorphous-phase theory for the explanation of the effect of cold work, mechanical deformation, etc., and one which is not ready at present to adopt this theory. It seems to me that this theory can at least be used as a convenient means of explaining various facts that are demonstrable in the laboratory but the presence of this amorphous material, through our lack of experimental means, we are unable to prove. That we have failed in this direction should not necessarily hinder us from using a theory as workable as this. Mathewson2 says: I have come reluctantly to believe in the amorphous theory, or some theory admitting a modification of the ordinary crystalline phase so as to permit differential properties with temperature, etc. If Mathewson represents one extreme, with Hoyt perhaps occupying a middle ground, H. M. Howe3 may be cited as one of the enthusiastic supporters of Beilby's amorphous theory. It is, says Howe:

Jan 1, 1923

YEAR OF r ELECTION 1913 FRANK DAWSON ADAMS Montreal, Canada 1921. WILLIAM CUTHBERT BLACKETT Sacriston, Durham, England 1923 GELASIO CAETANI Washington, D C 1920. HENRY STUROIS DRINKER Menon Station, Pa 1921. FERDINAND FOCH . Pans, France 1922. FEDERICO GIOLITTI Torino, Italy 1888. HATON DE LA GOUPILLIERE Paris, France. 1906. SIR ROBERT A. HADFIELD London, England 1921. FRANK WILLIAM HARBORD London, England 1921. HEINRICH O HOFMAN Cambridge, Mass 1917. HERBERT HOOVER .. Washington, D C. 1915 JAMES FURMAN KEMP New York, N. Y 1905. HENRI LECHATELIER Paris, France 1921. C. McDERMID London, England 1913 EZEQUIEL ORDONEZ Mexico City, Mexico 1909 ALEXANDRE POURCEL Paris, France 1911 ROBERT H RICHARDS Cambridge, Mass 1907. CHARLES D WALCOTT Washington, D C

Jan 1, 1923

By C. A. Allen

For over three years we have been endeavoring to reduce the number of fatalitics and minor accidents in Utah. The physical condition of the FIG: 1.—Number kiLlEd per million short tons of coal produced in ColoraI)o, New Mexico, utah, Wyoming, and bituminous mines of the United States 1014 to 1920. mines, concentrators, and smelters is good, yet the number of accidents,

Jan 1, 1923

ALABAMA Altoona -Cain, J Anniston-Cowie, L K Hermrod, A A White, H E Bessemer -Abbott, C E Ball, E M Mitchell, F R Thompson, N E Birmingham -Adler, J E Aldrich, T H Aldrich, T H, Jr Blackburn, A R Bush, M W Clark, G H Cowrn, P G Crane, W R Crawford, G G Crockard. F H

Jan 1, 1923

By W. O. Hotchkiss

An essential mental equipment for planning exploration is the fullest possible knowledge of the way in which the orebodies occur in the region to be explored, also the realization that in no mining district is this knowledge complete, and that new facts of importance will be revealed to the explorer in every exploration if he is in the proper frame of mind to grasp them. The geology of the ore deposits of the Gogebic Range for a long time was thought to be relatively simple, but work in recent years, by several men, has proved that this is not the case. We now realize that we are far from knowing all the factors that have resulted in the localization of ore deposits. For example, we have long known that the intersections of the dikes and the foot wall were favorable places to look for ore, but only within the last few years have we learned that there are several horizons in the various members, well north of the foot wall, that are likely to carry ore. The influence of the numerous cross faults on orebodies is not known or appreciated beyond a general realization that they are important. Just how they may be favorable or unfavorable to the localization of ore is not known. Such elementary information as the positions of these faults is just beginning to appear on the mine maps. Such being the condition, one can hardly overestimate the importance to the various operators and fee owners of careful studies of conditions in their properties for the purpose of assuring themselves that they are not missing valuable ore—that they are doing all the exploration that their situation demands in order to secure maximum returns. Valuable ores have been missed in the past and will be missed in the future. Only with a complete knowledge of all the factors that have united to produce ore could anything else be expected. The purpose of this paper is to call attention to these facts briefly and to suggest a few of the principles that should guide effective exploration. The foremost principle is that the man who starts out with the idea that he knows all about the mine geology of the Gogebic Range is starting with a heavy handicap.

Jan 1, 1923

ALABAMA Aldrich.-Lloyd, T W Anniston.-Carrington, F G Gerber, A B Heimrod, A A. White, H E Ashland.-Barton, J C Sturdevant, J C Bessemer.-Abbott, C E Ball, T L Hines, H K Hodgkin, W -0. Salmon, H S Thompson, N E Birmingham.-Adams, J H Adler, J. E Aldrich, T H Aldrich, T H, Jr. Ball, E M

Jan 1, 1923

By H. J. Rahilly

Mine fires, in the Butte district, have been a source of trouble and expense for the past thirty years, for while the actual fire area in most of the mines has been comparatively small, the handling of the gas has generally been a much larger problem than the actual putting out of the fire. The chief causes of these fires have been: Defective electrical equipment, incendiarism or carelessness, and spontaneous combustion. While fires from the first two causes have been numerous, they have generally been discovered and extinguished before they became very serious. Spontaneous combustion has been the cause of most of the large fires. Sufficient heat has been generated by ground movement, high rock temperatures, and decomposition to set fire to inflammable materials (tarred ropes, canvas, dry timber, manure, and hay) left in the gobs some years ago. Also, the heat resulting from the oxidation of the fine broken sulfide ore is sometimes sufficient to set fire to the timbers. In 1906, a fire was discovered on the 1100-ft. level of the Minnie Healy mine about 400 ft. (122 m.) west of the Minnie Healy shaft, which presumably originated, in one of the upper levels, from spontaneous combustion. The fire was walled off by concrete bulkheads and a pillar of ground 100 ft. (30 m.) thick was left below and mining resumed underneath. During subsequent operations, this pillar became cracked and broken and the fire passed into the new workings. It travelled downward and spread rapidly until, in 1917, it had become necessary to wall off portions of the Tramway, Leonard, and West Colusa mines on the 1300, 1400, 1500, 1600, 1800, 1900, and 2000-ft. levels, and the tops of the 2200-ft. raises were sealed. The fire area now consists roughly of a block 1000 by 1200 ft. and from the 600-ft. to the 2200-ft. level. This block is composed largely of a series of parallel northwest-southeast nearly vertical veins and stringers that form a large orebody, with no well-defined walls but badly fractured and faulted, and known locally as "horsetail ore." These veins, or orebodies, are mined by the square-set or the rill method.

Jan 1, 1923