Search Documents

Jan 1, 1935

By Emory Kemler

The problem of determining the most desirable operating conditions of an oil-well pumping unit or rig front, the selection of the proper material and size of sucker rods, and the design of a pumping unit require that sucker-rod loads be known with a reasonable degree of accuracy. The segregation of rig losses, the proper selection and operation of prime mover and reduction unit, and the analysis of the operation of subsurface equipment require a knowledge of polished-rod horsepower. The investigation of such problems as the instantaneous stresses set up in a pull-rod line or backside crank installation when the well is suddenly hooked on, a study of such problems as the effect of anchoring the tubing on rod load, tubing stresses and rod horsepower, and an analysis of the effect of subsurface equipment on rod loads make it necessary to have a dynamometer that is rugged, which can follow the sudden changes in load without any lag or damping effect, which will record the load in its true position with respect to polished-rod movement, and which will give a card large enough to allow the desired effects to be measured accurately. The inadequacy of the spring or fluid-pressure type of dynamometers has been covered in detail1. The data given show that dynamometers of the spring or fluid-pressure type exert a damping action on the peak loads and the inertia and friction of their load-indicating mechanism introduces a phase lag in recording the load. A dynamometer of that type will not give the load in the correct amount and will not record it in its true position with respect to stroke or time. New Type of Dynamometer Fig. 1 shows a magnetic strain-gage type of dynamometer, to be described in this paper. The strain gage A is used for measuring the load in the polished rod, a washer B and knife edge C take care of initial misalignment and reduce bending in the compression tube of the strain gage. The complete instrument can be transported in the carrying case E.

Jan 1, 1935

By Ralph J. Schilthuis, William Hurst

The nature of the forces that are important in producing the oil in the East Texas field and the manner in which these forces are affected by the rate of production have always been problems of outstanding interest. These questions are of great interest to the industry as a whole on account of the economic importance of the East Texas field and to the engineers in particular on account of the unique character and behavior of the field. Subsurface pressure data throughout the field have been collected systematically, so that a quite complete history of the reservoir pressures has been kept as the field has been developed and produced. Subsurface samples of the oil and gas have been taken and these have been examined to obtain data on the physical properties of the reservoir fluids under the actual conditions of temperature and pressure. All of these data have been valuable because they have afforded the basis for a careful study of the means by which the oil is produced. It is the purpose of this discussion first to point out several of the important facts revealed by the data mentioned and then to describe studies that have been made concerning the interpretation of these facts. Reservoir Pressure Data and Properties of Oil The reservoir pressure data on the East Texas field have shown conclusively that the pressures are readily affected by changes in the rate at which the field is produced. This can well be seen in Fig. 1, where the average reservoir pressures obtained from time to time are plotted with the daily production rates and the cumulative production of the field. It is noted that the average reservoir pressure has declined irregularly, depending upon the rate of production, from the estimated original value of 1625 Ib. per sq. in. to the value of 1228 lb. per sq. in. observed for Aug. 11,1934. The decline in pressure has been more rapid at the higher rates of production than at the lower rates. In contrast, the average reservoir pressure has increased, on several occasions, upon reduction of the withdrawal rate from a high value to a lower value. The reservoir pressure data have also shown that a definite gradient in pressure has existed across the field from west to east since the begin-

Jan 1, 1935

By H. A. Schwartz

THE spheroidal form of the temper carbon nodules in malleable cast iron and of the graphite mottles of "mottled" cast iron suggests that in both all the graphite in a given mottle or nodule grew from a single center of crystallization or nucleus.? There is, however, a distinct metallo-graphic difference between the mottle and the nodule; the area of mother metal impoverished in combined carbon by the crystallization of graphite in a mottle is practically coextensive with the ramifications of the graphite, while the impoverished zone of metal corresponding to a given nodule is always larger, and usually much larger, than the approximately spherical mass of graphite crystals forming the nodules. Furthermore, the mottle probably is formed during freezing and the nodule almost always at a considerably lower temperature. Assuming that the nodules or mottles can be used as a measure of the existing nuclei, (capable of germination) we propose to record certain observations as to the graphitizing reaction in the light of the number and habits of growth of these nuclei. The present authors, in cooperation with others1-7, have reported upon various cognate aspects of the problem. The fact that temper carbon is a mass of flakes and not a solid granule has become well recog-nized since the introduction of an improved polishing technique8,9,10 for cast iron. The problem of deriving from the circular planar intercepts

Jan 1, 1935

By William Buell

As used in connection with open-hearth or other high-temperature operations, "insulation" refers to a multitude of substances, natural or manufactured, that have the one principal property of preventing the flow of heat by conduction to a greater degree than refractories can prevent it, the principal properties of the latter being resistance to tem-perature and/or chemical action. The term "control" as commonly applied to the mechanization of management functions is inappropriate without qualification, for without some degree of control of every operation we could produce no steel worthy of the name. Although grouped together in this paper, insulation and control in open-hearth furnaces have little, if any, interrelationship, therefore the paper is made up of two distinct parts.

Jan 1, 1935

Jan 1, 1935

Jan 1, 1935

By R. J. Colony

DEPOSITS of iron are widely scattered in the folded Cretaceous rocks and the associated igneous intrusives of Puerto Rico. Most of them are too small for commercial development, but a few have aroused some scientific and economic interest, among them the large body of residua] limonite at the west end of the island near Mayaguez1-6 (Fig. 1) and the mixed hematite and magnetite deposit on the southern slopes of the Sierra de Cayey, about four miles north of Arroyo.7-9 Neither of these orebodies has been developed, nor have investigations of the widely distributed deposits of magnetite, which include all the remaining occurrences of iron deserving of economic consideration, proceeded beyond the exploratory stage. With the possible exception of the mixed deposit near Arroyo, the magnetite is directly associated with andesitic and dioritic intrusives, which invade the Cretaceous rock section, and the bulk of it, occurring in calcareous sediments, is clearly of contact-replacement origin. The small deposit on Rio Portugues, north of Ponce, is found in a limestone band near its contact with an andesite dike.10,11 Two deposits of unde-

Jan 1, 1935

By Bernard Moore

AT present the demands of the United States for strontium are met by imports from Germany, England and Canada, which vary considerably in proportions of ore and finished salts, in tonnage and in value. Statistics for the period 1926-1932 are given in Table 1. Domestic deposits are TABLE 1.-Strontium Imported into the United States, 1926-1932a Ore Chemicals Year Short Tons Value Pounds Value 1926 2,200 $58,159 5,433,044 $115,436 1927 1,356 58,711 4,233,816 149,383 1928 759 31,157 3,380,464 136,561 1929 973 45,505 4,578,327 196,233 1930 220 10,459 2,153,788 104.807 1931 (260 lbs.) 123 1,742,714 83,564 1932 5 276 469,481 20,910 a Mineral Industry (1934) 42, 61. known in many states, but the, larger and purer ones are in the West, particularly in the desert region of southeastern California and western Arizona. These deposits are large enough to command interest, par-ticularly in consideration of future cheap power at the Boulder Dam. The deposits described in this paper were examined during an investi-gation of the mineral resources of the Boulder Dam region by the United States Geological Survey for the United States Bureau of Reclamation in the spring of 1934. Mr. D. F. Hewett, who had general charge of the investigation, Mr. W. T. Schaller and Mr. M. I. Goldman contributed many helpful suggestions. Mr. N. H. Harshman assisted efficiently during the field work.

Jan 1, 1935

By V. R. Garfias

Principal events in petroleum operations of Mexico during 1934 have been the completion of three producing wells in the Poza Rica area and the plans for the expansion of operations of the Cia. de Petroleos de Mexico, S.A. (Petromex). Production for 1934 is estimated at close to 38,000,000 bbl., an increase of 4,000,000 bbl. over the previous year; an increase due in large part to the successful development in Poza Rica. The output of the South fields (Golden Lane) and Tehuantepec fields also increased somewhat during the year. Production of natural gasoline increased from 382,000 to 431,000 bbl. in 1934. Crude run in local refineries is estimated at 26,000,000bbl., some4,000,000bbl. more than the previous year. Exclusive of bunker fuel exports totaled 24,000,000 bbl., or 3,000,000 more than in 1933. Domestic consumption increased approximately 500,000,bbl. during the year, reaching a total of close to 13,600,000 bbl., exclusive of ships' bunkers. A total of 148 wells were completed as compared to 91 in 1933 and 40 in 1932. In proven areas, 133 completions resulted in 54 producers and 79 failures. The 15 wildcats drilled during 1934 gave no encouraging results. Seven of these were located in the border zone of northeastern Mexico; three tested possible northeast extensions of the Northern fields; two were drilled for possible extensions of the "Golden Lane" and three were completed in the Isthmus of Tehuantepec. Fields Northern Fields (Heavy Oil District).—There were 34 producing wells and 71 failures completed in the Northern fields, as compared to 20 producers and 20 failures in 1933. Practically all new producers were drilled to the shallower San Felipe formation, while wells drilled to the deeper Tamasopo limestone encountered salt water. Production of the field totaled 11,890,000 bbl., a decrease of 7.5 per cent from the previous year. Acid treatment was attempted during the year in seven wells

Jan 1, 1935

By Francis M. Rice

Before the world-wide depression, the primary purpose of most blast-furnace operators was to produce a maximum tonnage of pig iron per day for each furnace in blast. Some attention was paid to the conservation of labor and raw materials, but the idea was well established that low-cost pig iron was attainable only when each furnace was producing a high tonnage. After the depression had set in, the picture changed considerably. Each blast-furnace operator was forced to run his plant in a manner that best fitted the economical set-up of his company. A great deal of thought was expended on the different methods of operation, always with the idea of making each product in a way that would best serve his company financially. Because of this abnormal condition, the blast-furnace man was compelled to indulge in various practices of which many had been believed to be next to impossible up to that time. The ultimate purpose of these innovations was either one or a combination of the following: 1. To produce only enough pig iron for immediate consumption at a minimum cost. 2. To produce gas for boiler or mill use to supplant some higher priced fuel. 3. To consume the coke produced at the coke plant, which was often viewed as a byproduct. 4. To protect the cash position of the company. These conditions were met by diverse methods, some of which were: 1. Slow or decreased wind. In some instances the blast blown was held as low as 25 per cent of the normal volume. 2. Intermittent operation, in which the furnaces were shut down or "fanned" at frequent intervals.

Jan 1, 1935

By Howard Smith

OF late considerable experimental and, theoretical interest has been shown in the rates of transformation from a single phase, usually a supercooled solid solution, into one or more phases. Such reactions may involve both diffusion and transformation of the major constituent, as in iron alloys, or it may simply involve diffusion, as in superstructure forma-tion and in age-hardening systems. Most of the work has been confined to ferrous alloys1-9t although two investigations have been made on copper alloys10,11. That such work may be of considerable, practical importance has been demonstrated by Bain12, by the workers at the Kaiser Wilhelm Institut fur Eisen-forschung13,14, and by the everyday use of precipitation and age-harden-inn principles15. Experiments in this country have generally followed Davenport and Bain's technique of rapid supercooling followed by isothermal treatment. In Germany16,17 the work has been extended to the study of the influence of accurately controlled and measured rates of cooling. The work on steel indicates that there are two subcritical temperature ranges where reaction starts sooner after quenching and proceeds at a more rapid rate than at other temperatures. At subcritical temperatures above Ar" where reaction is dependent upon atomic migration there is a period of time of which the length depends upon the alloy content and the temperature, before which no reaction has been detected. Daven-port and Bain1 find that different sorts of atoms in solid solution in gamma iron affect the length of this "prereaction" period differently, manganese

Jan 1, 1935

Jan 1, 1935

Terminology Relating to Nonmetallic Elements in Metals. BY T D YENSEN AND C H HERTY, JR (Tech Pub 555, Metals Tech, June 6100 words ) The paper gives arguments for confining the term "gases in metals" to its proper sphere and recommends the name "nonmetallic elements in metals" as a general title of the subject dealing with: (1) nonmetallic elements introduced into metals unintentionally or for various specific purposes; (2) phenomena occurring in metals caused by non¬metallic elements It also recommends a classification of the subject in which "gases in metals" occupies a definite, logical place

Jan 1, 1935

By J. B. Austin, R. H. H. Pierce

IN developing a consistent picture of the thermal expansion of the commercial chromium steels, which cover a range of, carbon contents, it is desirable to know the expansion in the limiting case of the binary, carbon-free, iron-chromium alloys. We have, therefore, determined the thermal expansion of a series of five special alloys, ranging in chromium content from 3 to 10.5 per cent, with not more than 0.03 per cent carbon, over a temperature range extending beyond the transformation region; this low carbon content enables us to draw reasonably reliable conclusions as to the behavior of the carbon-free system. Moreover, the measurements serve to determine the beginning and the end of the alpha-gamma transformation; and they emphasize once more the fact that a transformation temperature determined by any method in which the specimen is .cooled at an appreciable rate is apt to be seriously in error, particularly if the metal contains a transformation-retarding element such as chromium or managanese. The lag, or undercooling, observed at the ?-a transformation is explained in terms of the influence of temperature on transformation velocity; the rather unusual shape of the ? loop is attributed to a change with temperature and with composition of the distribution of chromium between the alpha-iron and gamma-iron solid solutions. The exact composition of the alloys which were obtained through the courtesy of Dr. W. Rohn, of the Heraeus Vakuumschmelze A-G., is given in Table 1. Determinations of the linear thermal expansion and of transformation temperature were carried out in the vacuum dilatometer previously described,1 using a rate of heating and of cooling of 3.0° to 3.5° per minute unless otherwise stated. Magnetic susceptibility, which was measured in studying the rate of transformation, was determined with a magnetic balance, which also has. been described.2

Jan 1, 1935

By R. W. Moore, A. B. Kinzel

Although the iron-carbon diagram has undergone many changes in the last 20 years, the region below the eutectoid line and up to approximately 1.7 per cent carbon has been little affected. This region is generally considered to consist of cenlentite and ferrite. Graphite has been noted occasionally in the hypereutectoid steel region, and the ready formation of graphite nodules in malleable cast iron is a phenomenon difficult to interpret in the light of cementite, supposedly stable at sub-eutectoid temperatures. In this case the graphite formation has been partly explained by the presence of silicon, and many have believed that silicon acts to change the stable state rather than to accelerate reactions so as to arrive at the stable state in a briefer period of time. Consideration of this phenomenon indicates that cementite is not the stable phase in the temperature composition zone referred to. In the course of examining a low-carbon steel tube taken from a petroleum cracking still, which had been in service for approximately three years at temperatures somewhat below the eutectoid temperature, observations were made that shed light on this entire subject. The tube in question analyzed:' C, 0.15 per cent; Mn, 0.49; Si, 0.02; S, 0.023; P, 0.015. The microstructure of the tube after service is shown In Figs. 1 and 2. From these it is evident that cementite as such is absent, and that in its place nodular graphite has been formed. In order to check this observation further, samples taken from the tube were heated at 850" C. for varying periods of time. The small samples were put into a large hot furnace, and the total time is recorded. The structure of the sample after 5 min. at 850" C. is shown in Figs. 3 and 4, and the nest of pearlite surrounding the graphite nodules is most satisfactory evidence of the character of the nodules. As the length of time of heating at this temperature increases, the pearlitic zone increases, with final restoration

Jan 1, 1935

By Paul D. Merica, W. A. Mudge

ONE of the most prominent features of our present-day industrial development is the ever-increasing demand put upon materials of construction Engineering ingenuity, within the past 25 years, has been unusually active, and in some fields at least engineers frankly say that engineering design has progressed as far as the limitations imposed by the properties of the present materials of construction will permit. Consequently, they are today demanding improvement in their working materials and seeking new ones, through the aid of which the present limitations of design may be overcome The activity of this search is evident in all fields, but it is particularly so in that of structural materials required to be resistant to corrosion The corrosion resistance of metals and alloys is never absolute and all-inclusive, a particular alloy will withstand some corrosive conditions well and fall utterly under others Furthermore, other properties, physical and mechanical, required in conjunction with corrosion resistance vary considerably for different commercial applications One wants a soft, ductile sheet metal resistant to atmospheric corrosion, another, a high-strength alloy resistant to sulfuric acid The last decade has witnessed active and definite progress in the development of high-strength, corrosion-resisting alloys In June, 1924, a symposium by the American Society for Testing Materials, on Corrosion-Resistant, Heat-resistant and Electrical-resistance Alloys, disclosed no less. than 60 commercial alloys the properties of which were described as being suitable for industrial service where corrosion resistance

Jan 1, 1935

By George Holderer

THE relation between man-hours of labor and production may be correlated for any industry, and already it has been widely used in piece-work studies. It is not in general use as yet for recording labor efficiency of an enterprise or an industry. An exception to this is the Cement Institute, which tabulates the man-hours used in each operation and FIG. 1.-LABOR PRODUCTIVITY IN COPPER MINING. thus gets the total man-hours per barrel of cement. The writer knows of one steel company that keeps a complete record of man-hours for every operation from mining the ore to finishing the product. No doubt many others find the information useful, and such a study could be of value to the mineral industries.

Jan 1, 1935

By C. C. Henning

IN any line of human activity logical handling requires an amount of attention to each phase that is in keeping with the importance of that phase. In the complex and rapidly changing field of modern ferrous metallurgy it is difficult to allot the proper degree of attention to the various subjects, and it is not surprising that one or more subjects of major importance should for a time be neglected. Bessemer steel is a good example of a neglected subject. It is largely taken for granted, inferior physical quality is assumed for it, and there is a lack of interest in its technical development and commercial application. Availability of supply is limited. In spite of this technical indifference, limited source and lack of commercial exploitation, bessemer steel con-stitutes a large volume of tonnage in daily use. There is a fairly prev-alent idea even among technical people that bessemer steel survives mostly because of low cost and by reason of a dwindling residue of applica-tions sufficiently common to permit of its use. The difference in cost between bessemer and open-hearth steel is governed largely by the relative cost of manufacture of pig iron and the market price of steel scrap. During the past four years there have been long periods of time during which the price of steel scrap was low enough so that open-hearth steel was considerably lower in manufacturing cost than bessemer. As to application, it may be pointed out that thousands of tons of this material in the form of bessemer screw steel are applied for moving parts in automotive and other equipment. Some forging work and considerable heat treating, particularly carburizing, is performed on this grade.

Jan 1, 1935

By H. H. Pierce, J. B. Austin

In developing a consistent picture of the thermal expansion of the commercial chromium steels, which cover a range of carbon contents, it is desirable to know the expansion in the limiting case of the binary, carbon-free, iron-chromium alloys. We have, therefore, determined the thermal expansion of a series of five special alloys, ranging in chromium content from 3 to 10.5 per cent, with not more than 0.03 per cent carbon, over a temperature range extending beyond the transformation region; this low carbon content enables us to draw reasonably reliable conclusions as to the behavior of the carbon-free system. Moreover, the measurements serve to determine the beginning and the end of the alpha-gamma transformation; and they emphasize once more the fact that a transformation temperature determined by any method in which the specimen is cooled at an appreciable rate is apt to be seriously in error, particularly if the metal contains a transformation-retarding element such as chromium or managanese. The lag, or undercooling, observed at the ? — a transformation is explained in terms of the influence of temperature on transformation velocity; the rather unusual shape of the ? loop is attributed to a change with temperature and with composition of the distribution of chromium between the alpha-iron and gamma-iron solid solutions. The exact composition of the alloys, which were obtained through the courtesy of Dr. W. Rohn, of the Heraeus Vakuumschmelze A-G., is given in Table 1. Determinations of the linear thermal expansion and of transformation temperature were carried out in the vacuum dila-tometer previously described,' using a rate of heating and of cooling of 3.0" to 3.5" per minute unless otherwise stated. Magnetic susceptibility, which was measured in studying the rate of transformation, was determined with a magnetic balance, which also has been described.2 Results and Discussion Thermal Expansion Coeficients.—Numerical values for the linear expansion coefficient, derived from a smoothed curve based on at least

Jan 1, 1935