Search Documents

By Howard S. Bryant

Kansas maintained its fourth position on the list of all oil-producing states, for the ninth consecutive year. Total crude-oil production during 1935, as reported by the Oil & Gas Journal, was 53,364,446 bbl. on 97 per rent tank table calculations. This represented an increase of 17 per cent over the production in 1934, which had been the all-time peak of production in Kansas up to that time. Many of the 51 new discoveries of the year, listed in Table 2, did not have a pipe line outlet until about January, 1936; therefore did not contribute to the 1935 production of the state. The potential of all wells in Kansas at the end of the year was 998,-000 bbl. per day, and the daily allowable was 143,000 bbl. per day, showing proration to the extent of 14 per cent of capacity, under the rules of the State Corporation Commission. Several important new pipe lines were built into western Kansas by extending older lines from east to northwest, providing additional outlets for new crude-oil production, and increasing the service facilities from the older oil fields. The crude-oil price level remained unchanged throughout 1935 as it did in 1934, the price of Kansas 36" gravity crude being quoted at $1 per barrel. However, on Jan. 9, 1936, the price of this gravity oil was raised to $1.10 per barrel. Following the trend of the past several years, drilling activity was largely in western Kansas, and showed a still farther westward push from last year. A relatively high percentage of successful wildcat wells at a relatively shallow drilling depth, combined with the expiration of leased acreage assembled before the depression, caused the rapid exploration and development campaign, begun in 1934, to continue. This has caused the opening of more new fields in 1935 than during any previous year in the history of oil production in Kansas. A summary of the results of drilling in western Kansas is given in Table 2. Eastern Kansas had considerable drilling, showed six new fields or extensions of oil fields, but in the limited space of this paper such developments cannot be described.

Jan 1, 1936

By George Ashley

IT has been said that the Pittsburgh bed is the most valuable single mineral deposit yet known to man. The figures in Table 1 are presented in substantiation of that claim. TABLE 1.-Pittsburgh Coal Bed to Dec. 31, 1934 Estimated Recov- State Thousands of ( Value erable Reserves Tons Mined (1935), Thousands of Tons Pennsylvania 3,144,000 $4,922,000 7,500,000 Ohio 493,391 843,699 3,000,000 West Virginia 650,000 1,027,000 5,500,000 Maryland 183,224 254,681 20,000 Totals 4,470,615 $7,047,380 16,020,000 PRODUCTION AND VALUE In order that the figures of Table 1 may have any weight, a statement must be made to show how they were arrived at. Because, to the writer's knowledge, no accurate separate figures ever have been kept of the production and value of the Pittsburgh coal bed, the states will be considered separately.

Jan 1, 1936

By F. B. Plummer, R. B. Newcome

The practice of introducing acid into oil wells to increase production of oil and gas has been in use since 1894, when it was first used in the Pennsylvania oil fields30.‡ It is only since 1928 that it has been used to any extent in the Mid-Continent18. The process has proved successful in increasing production, at least temporarily, in depleted oil fields where the producing formation is highly calcareous and where water drive is not too pronounced. In the Zwolle field in Louisiana, where the producing horizon is a chalk, increases of 100 per cent have been recorded25. In north-central Texas, where the oil is produced from the Marble Falls limestone, equally pronounced increases have resulted3. The production also in some fields yielding oil from quartz sand cemented with calcitc has been benefited. The evidence of actual increase in total recovery of oil, however, has been questioned by some engineers18. It has been pointed out that the results of the treatment of a well in a now district, where the process has never been tried out, can never be predicted with certainty, since other factors besides percentage of calcareous content of the oil sand play a large part in determining the success of the method. Numerous articles have been published on acid treatment and on the effects of acid on limestone1-35, yet very little has been written concerning experimental work on the actual effect of acid on capillary pores and larger oil-coated voids of oil sands. This is due partly to difficulties in duplicating field conditions in a laboratory and partly to the fact that the process has been carried out largely by contracting companies that have been unwilling to publish details of their results for fear of loss of business to competitors. The authors, using equipment developed to measure the radial permeability of oil-sand cores2', have developed a method of investigating the results of acid treatment which has enabled them to test numerous cores and to study in some detail the action of acid on the different types of rocks, particularly fine-grained rocks.

Jan 1, 1936

Jan 1, 1936

By W. E. Forsythe

Different forms of optical pyrometers are discussed and the advantages and disadvantages of the different types for measuring high temperatures are pointed out. These advantages and disadvantages lead to the selection of the disappearing-filament type of optical pyrometer for most work. Attention is directed to the necessity for the use of a monochromatic screen with a pyrometer, which leads to a discussion of the meaning and use of the effective wave length of the screen. Methods of calibrating the optical pyrometer are outlined and it is shown that an optical pyrometer can be calibrated just as definitely as any other temperature-measuring device. Accuracy tests are included, in which it is shown that excellent results can be obtained by even untrained or slightly trained observers with this form of optical pyrometer. The various corrections that are necessary in this kind of work are indicated, including corrections for stray light, for absorption of windows, of smoke, and so forth. The troublesome problem of measuring the temperature of bodies that do not radiate like a black body is discussed and the corrections for reducing such readings to the true temperature are given for a number of different materials. Introduction The fundamental idea of temperature depends upon our temperature sense and bodies are said to be hot or cold depending upon the reaction of our hands or some other part of the body to the heat from the source investigated. For measuring the temperature some instrument must be devised, since the temperature of the source studied is apt to be so hot as to greatly injure any part of the body that comes near it, to say nothing about direct contact with it. Definition of Temperature.—The temperature scale is based upon two fixed points, the temperature of freezing water and the temperature of boiling water. This temperature interval, depending upon the scale

Jan 1, 1936

By Mark Malamphy

MOST igneous rocks, and particularly those of the basic type, con-tain relatively high percentages of magnetite and other iron oxides, which give them moderately high magnetic susceptibilities and make them responsible for an important percentage of the magnetic anom-alies observed during the course of geophysical surveys by the mag-netic method. The irregular form and high susceptibility of the igneous rocks make them readily polarizable and the position and strength of the magnetic poles formed are not always explicable by theoretical calculations of anomalies due to certain assumed forms in the normal magnetic field of the area under study. During the last four years our field work has permitted us to make detailed observations of anomalies due to igneous rocks in all the states of south Brazil. The form and position of the igneous rock at some places were fairly accurately known, which made it possible to calculate theoretical anomalies and compare them with the observed data. Some of the data we obtained have been published and additional cases are now awaiting publication. In this paper, we will present a few specific cases where the geology is moderately well known and which we believe to be of considerable value as representing typical magnetic anomalies in the south magnetic hemisphere, where the inclination of the magnetic field is very low. Although the vertical intensity is negative in the Southern Hemis-phere, we have adopted the convention of plotting increase in intensity (negative) as a positive anomaly; i.e., above the x axis. This conven-tion facilitates comparison with anomalies in the north.

Jan 1, 1936

By R. H. Harrington

THE definition of precipitation-hardening is well understood and its principles have been subjected to study for some time. However, the variation of properties with double aging, combined with strain-hardening, gives promise of new and useful phenomena. Properly to understand these distinctions, definitions of these terms are necessary. Precipitation-hardening. This reaction usually depends upon an alloy having such a composition that it consists only, or in major part, of but one phase, a solid solution, at a high temperature, so that, upon slow cooling, this solution breaks down into two phases, the solid solution and a compound. By heating the alloy to the temperature for maximum solution of the compound, quenching, and reheating to a suitable lower temperature for critical dispersion precipitation of the compound, useful properties of the alloy may be developed to a maximum. Double Aging.-Dougle aging in part is similar to the process for precipitation-hardening, consisting of heating a precipitation-hardening alloy to the solution temperature, quenching, reheating to the suitable dispersion precipitation temperature, strain-hardening, and again reheat-ing to a suitable temperature to develop certain useful properties to a maximum. The strain-hardening may be induced by two methods: (1) a rate of cooling from the first reheat may suffice to strain the solid solution lattice of the alloy; or (2) the alloy may be cold-worked to a suitable degree between the two reheats.

Jan 1, 1936

Jan 1, 1936

By Samuel Shallcross

TO principal function of the Bell limestone mine, of the American Lime & Stone Co., at Bellefonte, Pa., is to supply raw material to the company's modern rotary kiln plant at Bellefonte. Because mining costs are naturally higher than many open quarries with more favorably lying strata, it cannot compete, except to a limited extent, in the markets for road material and fluxing stone. In the broad sense, mining does have an advantage over the average open quarry when the end products are designed for and controlled by process and final inspection for the exacting demands of the industrial and chemical markets. Approximately 80 per cent of the output of the Bell mine is sold in the industrial and chemical markets. And as higher standards are set each year for construction and agricultural work, the remainder of the mine output goes to these two classes. Mining produces more fines than open quarries, and these fines are difficult to market; on the other hand, owing to absence of contaminating clay and impure rock, a greater percentage of the output of a mine is marketable. Because of the great production of fines, rotary kilns for lime burning are necessary when the stone must be mined. In 1921 the American Lime & Stone Co. operated 19 quarries and 72 lime shaft kilns spread over an area of 40 miles between Bellefonte and Altoona, Pa. At that time the lime-production capacity of the 72 kilns amounted to approximately 700 tons per day. After 15 years the company operates three rotary kilns and six shaft kilns, with a combined output of approximately 500 tons of lime per day, concentrated in its single Bellefonte plant (Fig. 1). Its only stone-producing plants are now the limestone mine at Bellefonte and a construction-stone open quarry at Union Furnace, near Tyrone, Pennsylvania.

Jan 1, 1936

By A. A. Berk, W. C. Schroeder

Practical experience has shown that at elevated temperatures solutions containing sodium hydroxide may attack stressed steel in a manner that cannot be explained in terms of ordinary corrosion. Because the ductility of the metal has been greatly reduced during the reaction, the entire phenomenon is usually called "embrittlement." Thus, after several years of operation caustic evaporators have been so badly embrittled that rivets could be cracked off with the blow of a hammer. Since fine intergranular cracks are almost always present in the zone of fracture, it has often been assumed that a process of selective corrosion in grain boundaries was responsible for the failure, although this has not been clearly proved experimentally. Concentrations of sodium hydroxide below those necessary for the uniform, rapid attack of the steel surface are reported to be most effective in producing embrittlement2, 3. In the operation of steam boilers a similar type of failure has been found, mainly in riveted seams or other capillary spaces where the solution may concentrate and where high stresses may also exist. It is believed that in such localized areas the dissolved solids may reach a value many times the few hundred parts per million prevalent in the body of the boiler. While this type of boiler failure has been the subject of investigation for a period of 20 years1, an understanding of its mechanism and a rational basis for complete protection have not yet been secured. To procure this information the present investigation was

Jan 1, 1936

By Howard Smith

FOR several years this Institute has recorded in its TRANSACTIONS the various discoveries of potash? in America, and the successive stages in the development of an independent domestic potash industry. This paper is intended primarily to continue the record through the year 1935. In retrospect it is not inappropriate to note that public interest aroused in 1910 resulted in the production of some 1090 tons of pure potash in 1915, as a small beginning in the domestic inorganic potash industry, and that the infant industry thus begun reaches its majority this year, following a record production in 1935 of about 600,000 tons of potash salts and exports to no less than 22 foreign countries, including six countries in Europe. This production, with an estimated 200,000 tons of pure potash, may be compared with a production in 1934 of 430,157 tons with an equivalent of 144,342 tons of pure potash.

Jan 1, 1936

By Charles G. Maier

It has long been supposed that when crystalline materials are comminuted the energy used in the production of increasingly smaller grain sizes is not entirely dissipated as heat but that a certain portion is "stored" as a part of the internal energy of the material. This portion usually has been called the "surface energy" of the particles. The practical interest of the Bureau of Mines in this subject in connection with the energy requirements of crushing processes has led to the author's attempt to measure the "stored" energy in finely divided calcite by heat-of-solution methods1.t The experiments on calcite showed that "storage" of energy could not be proved for this material, because fine grinding caused a lack of chemical homogeneity evidenced by loss of carbon dioxide and subsequent adsorption of water on the surfaces of the calcite particles. When thermochemical correction was made for composition changes the corrected heat of solution was less for fine material than for coarse. Continuation of the experimental work into the problem of comparing work and heat in the deformation of metallic crystals, where the calorimetric difficulties were less, showed, however, that in the case of copper and aluminum a real discrepancy between work and heat could be shown. Similar results had previously been obtained by Farren and Taylor2 and Hort3 and more or less simultaneously with the author's work by Rosenhain and Stott4 and by Taylor and Quinney9 The results obtained by the different investigators were not satisfactorily consistent, but the experiments of Taylor and Quinney constitute by far the best figures obtained to date. The previous paper1 presented evidence to show that if energy is stored in the surfaces of crystals the densities of fine crystals should differ

Jan 1, 1936

By G. S. Hume

Petroleum is produced in Canada in the provinces of New Brunswick, Ontario and Alberta and in the Northwest Territories. The total production, however, is relatively small in comparison with the consumption, the value of imports exceeding 40 million dollars a year. Production figures are given in Tables 1 and 2. In Turner Valley, still the largest producing gas and oil field in Canada, five wells were completed during the year. The largest of these

Jan 1, 1936

By William Reynolds

THIS paper deals with the results of a study of the application and development of mining machines for cutting out and removing dirt bands in bituminous coal beds. FACE PREPARATION When one or more dirt bands1 occur in a seam of coal, the problem of elimination of impurities becomes manifest. The degree of complete-ness to which these impurities are removed at the face has an important bearing upon labor costs, haulage costs and outside cleaning costs, and often the ash content of the product is markedly affected. Yet, because the present-day miner is paid for the number of tons he loads he often lacks interest in the quality of the coal. To insure a clean product, a system of penalties for dirty coal is enforced, but control of extraneous impurity content in the loaded coal is often inadequate and ineffectual when coal and banded impurity are shot as one. It seems only logical that to reduce the amount of impurities by proper face preparation before the men are permitted to load the coal is the most efficient method of preparation.

Jan 1, 1936

By William E. Brewster

Dating back some five years ago, various foundries made inquiries as to the probable total carbon content in a given specification and grade of pig iron. Up to that time we had no data, and except for a few occasional determinations of total carbon, no attempt had ever been made to set up routine determinations of total carbon. In fact, at that time, a cast analysis was considered sufficient, without examining at further length into possible variations of analysis between ladles of the same cast. In view of the various inquiries as to total carbon, we sampled all piles of all grades of pig iron, making complete analyses. Finding some variation in carbon content, we secured more samples and plotted the carbon content with respect to silicon in each grade of iron except for the higher phosphorus foundry iron, where it was necessary to divide the group into twenty-point phosphorus ranges. This is easily understood, owing to the falling off of carbon content with the increase in phosphorus content, silicon in each case being the same. In addition, these curves clearly demonstrate the lowering of the carbon content as the silicon is increased. In order to insure accuracy and reliable determinations the following method of sampling and analysis was employed: Two pigs selected from each end of the car, each car containing iron from one 50-ton ladle, are drilled with a 5/6-in. drill all the way through from top to bottom in the center of one section of the pig. The drillings are collected and transferred to an 80-mesh sieve; the portion passing through and the portion retained are placed in separate envelopes and labeled accordingly. The amount of sample in each envelope is weighed to obtain the proportionate amount of coarse and fine drillings, then a 1/2 factor weight of sample (1.3636 grams) made up of proportionate

Jan 1, 1936

By David B. Reger

The year 1935 was mostly quiet in West Virginia, and devoted to routine drilling in old pools and extensions. A notable exception to this general rule, however, was the further development and proving of a field of gas discovered in 1930 in the deep Oriskany sand (L. Dev.) in Kanawha County, as later discussed. No new pools of oil were found and little or no attempt was made to search for them. No new pools of gas were recorded but various extensions of old pools were made. There were no new pipe line extensions of consequence, either for oil or gas. Operating technology was much the same as in recent years, there having been some further advances in repressuring oil wells and in the use of acid for treating small wells in calcareous formations, and some change in the technique of shooting gas wells. Financially, there has been a full market for all crude oil produced and a fair market for gas. There have been occasional transfers of producing oil or gas properties, mainly between established companies. Most of the attempts made to finance mergers and new developments have failed largely because of difficulties encountered under the Federal securities act. This situation has prevented the normal turnover of properties by small operators who frequently desire to sell partly developed interests and then step out into new ventures. New Development In 1935 the State issued 569 permits for drilling and records the same number of completions. One trade journal records 533 completions and another 483. A running record kept by the writer accounts for 713 completions, with 156 oil wells, 417 gas wells and 140 dry holes (Table 3). Some of these completions may be old wells drilled to deeper sands. Some, apparently, have been drilled without legal permit. Extensions of Producing Areas Ritchie County has again led all others in new drilling, with 137 completions as compared to 74 in Calhoun and 61 in Cabell. This Ritchie County drilling was done mainly to extend or further develop old pools

Jan 1, 1936

By Ian Wark

SODIUM sulfide is used extensively to increase the recovery of oxidized copper and lead minerals by flotation, particularly when using xanthates as collectors. It is generally assumed that the sodium sulfide converts a film of the oxidized mineral to the sulfide, and that the xanthate, while not a very effective collector for the oxidized minerals, is a good collector for the sulfide. On the other hand, Taggart and his collaborators' claim that unless sulfide minerals are oxidized they cannot adsorb xanthates and do not float. Gaudin2 states that amyl xanthate, used in conjunction with sodium sulfide, gives better results than ethyl xanthate. Rabone3 and Mayer-Schranz4 agree that excess of sulfide functions as a depressant. Owing to the greater solubilities of the oxidized minerals than of the sulfides, the consumption of sodium sulfide is greater than that of most other flotation reagents, up to 10 lb. per ton of ore being used in some plants. Luyken and Bierbrauer5 recommend a water washing to remove soluble heavy metal salts; by this means sulfide consumption may be reduced. It was desirable to determine the limits of the sulfide concentrations between which contact is possible at surfaces of anglesite and cerussite in xanthate solutions. Similar determinations were desirable for the sulfide minerals with which the oxidized minerals are usually associated, since conditions should be chosen, if possible, so that the two types of mineral will float together. Because of the formation, especially in acid solutions, of hydrogen sulfide and of the hydrosulfide ion (HS-), the permissible limits of sulfide addition are obviously dependent upon the pH value. Sphalerite responds to ethyl xanthate only in the presence of an activator; for example, copper sulfate. It was necessary, therefore, to determine whether sodium sulfide interferes with the activation of sphalerite by copper sulfate. The combined effect of sulfide and copper sulfate was determined also for galena, chalcopyrite and pyrite.

Jan 1, 1936

Jan 1, 1936

By Harry T. Hamilton

THE genial assistant to the president of the New York Trust Co. is the latest addition to the Institute's board of directors, having been elected at the March meeting of the hoard to fill the unexpired term of the late E. E. Ellis. Usually when a banker is appointed to the board of a company the reason is obvious; the difference in this case is that the New York Trust Co. has some of the Institute's money, instead of vice versa. But Harry Hamilton is not really a banker-at least not primarily. Frefluently big financial institutions have a good mining engineer on their staffs to keep them from financing too many "cats and dogs." At any rate Mr. Hamilton gave up his consulting practice in San Francisco back in 1927, to accept his present position in New York. Until then, from the time he graduated from Yale in 1904, lie was constantly engaged in mining operations of one kind or another in the West and in Mexico. His first job was at Christmas, Ariz., where lie did "sampling and miscellaneous work" for the Saddle Mountain Mining Co. The writer tramped up to, all over, and through that property one hog day many years later, when it was run by the Christmas Mining Co., and carp assure the reader that without doubt the young Yale graduate got some good experience and was well broken in. From there Mr. Hamilton went to Cananea for a time, and then to the Copper Queen, at Bisbee, where he was a valued member of the rigging gang. An assignment of assaying and sampling for the Shan¬non Copper Co. at Metcalf lasted for a few months and then he accepted a job for a year with the geological department

Jan 1, 1936

By Paul T. Benson

MOST important of the various departments of a custom smelter, so far as the financial welfare of the plant and the confidence of shippers are concerned, is that responsible for correct weights, accurate moisture sampling, and the obtaining of control samples that are strictly representative of the lot of ore from which they come. Treatment rate schedules are based on the metal content of ores received, reduced to dry weight. These rates must be low enough to keep the ship- per from taking his business else- where and still must allow the smelter a profit. Assay results, likewise, must satisfy the shipper, but if they show too high a metal content for the ore they represent, the smelter will actually lose money. It is always considered, and constant checks through umpire assays prove, that laboratory results are closely correct, so the bur- den of the plant profit and loss and the satisfaction of the shipper rest squarely upon the sampling department.

Jan 1, 1936