Search Documents

By C. L. Shapiro, R. Schempp

DuRing the past few years, general interest in the steel-producing and steel-consuming industries has been centered on the so-called "inherent characteristics" of steels. While often vaguely described, these characteristics are known to influence the response to heat-treatment and the hardening characteristics of the material. Although most of the recent papers and discussions have associated the "inherent characteristics" with the austenitic grain size and emphasized the importance of it, comparatively little is known of the variables that may affect the size of the austenite grain. The work to be described in this paper was carried out during the course of a study on the inherent characteristics of tool steel containing one per cent carbon. The discrepancies encountered in the determination and classification of the austenitic grain size led to an investigation of some of the variants influencing the austenitic grain size as determined by standard methods. Methods of Determining Austenitic Grain Size The present methods used for the determination of the austenitic grain size may briefly be classified in two groups: 1. Etching at room temperature to reveal the austenite grain size prior to cooling. 2. Etching at elevated temperatures, cooling to room temperature, and observing the structural conditions that existed at the temperature from which cooling occurred. The outstanding methods of the first group are: (1) the McQuaid-Ehn test, (2) optimum rate of cooling, (3) quenching and etching. McQuaid-Ehn Test.—This established and accepted test does not need much elaboration. It consists of pack carburizing at a definite temperature for a standard period of time and slowly cooling in the furnace. The temperature is 1700" F. (925' C.) and the time is 8 hr. The interpretation and evaluation of this test are fairly well defined in the A.S.T.M.

Jan 1, 1937

Jan 1, 1937

Equilibrium in Lead Smelting. By S FREDERICK RAVITZ AND KENNETH E FISHER (Tech Pub 681, also Trans , vol 121 2300 words) Four liquids are ordinarily produced in lead smelting, namely, bullion, speiss, matte and slag To determine whether these exist together in equilibrium, the distribution of gold and silver among them was measured To crucibles containing similar mixtures of all four products, varying amounts of silver were added, and the crucibles were heated together under the same conditions for 3 hr, during which the charges melted and separated into four layers After cooling, these layers were assayed for silver, and the distribution coefficients, 1 e , the ratios of the concentration of silver in any particular layer to that in the bullion, were calculated In each experiment, each distribution coefficient was found to be constant, regardless of the amount of silver used Similar results were obtained using gold instead of silver The constancy of the distribution coefficients indicates that the bullion, speiss, matte, and slag exist together in equilibrium

Jan 1, 1937

Correlation between Metallography and Mechanical Testing By H F MOORE (Henry Marion Howe Memorial Lecture Trans, vol 120 11,000 words ) The lack of effective correlation between metallography and mechanical testing from the days of Reaumur to the present is noted, and two general problems of such cor¬relation are stated (1) the correlation of qualitative test results with quantitative, and (2) the correlation of average results with maximum or minimum results Some correlation has been achieved, notably in the field of heat-treatment and in the study of elastic strength of metals Correlation is in the process of being developed in several other fields, including the quantitative study of the effect of grain size of metal on mechanical properties, of grain size and type of crystalline structure on the sensitivity of metals to weakening at holes, notches and other "stress raisers," and in the study of the starting phases of spreading, "fatigue" cracks Correlation of mechanical test results and metallographic study is needed in the study of such problems as the various theories of failure of metals, the meaning of and tests for service ductility of metals, and the relative damaging effect of defects inherent in metals, such as minute cracks and segregation, as compared with the damaging effect of "imposed" stress raisers, such as screw threads, sharp shoulders, etc The neces¬sity for more correlation of metallography and mechanical testing during student days is emphasized, and also the need of a better understanding on the part of engi¬neers of the significance and limitations of metallographic apparatus and results and of X-ray diffraction This should be matched by a better understanding on the part of metallurgists of the significance and limitations of mechanical tests of metals, of testing machines and strain-measuring apparatus

Jan 1, 1937

By N. O. Johnson

THE Hog Mountain mine is a pyritic-gold property in the north central part of Tallapoosa County, Alabama, at an elevation of 800 ft. in the southern Appalachian region. It is 13 miles by a good secondary road from Alexander City, a station on the Central of Georgia Railroad. Since its discovery in 1839, the mine has been worked intermittently. The records of past operations are few and are scattered over a long period of time; however, available information indicates a production of approximately 12,000 oz. of gold prior to the present company's activities, which started in 1933. Additional 7844 oz. has been produced under the direction of the present management. The ore from stopes has averaged 0.200 oz. gold per ton; the ore from development, 0.136 oz. gold per ton. Silver, copper, iron and sulphur are also present but to date are of minor importance. The grade of ore in comparatively narrow veins makes necessary extreme vigilance in the methods of mining. Geology Wall Rock.-Hog Mountain consists of a quartz-diorite intrusion approximately 5000 ft. long by 1200 ft. wide. Its resistance to weathering, as compared to the surrounding schists, has led to the formation of a conspicuous ridge rising 400 ft. above the adjacent country. All the mining operations are confined within the limits of this quartz-diorite formation. . Except where there is excessive shearing, either parallel or at flat angles to the quartz veins, all the walls of the stopes within the limits of the veins are strong enough to make timbering unnecessary. Where shearing exists, there may be a sloughing off of the walls, especially in the process of drawing the ore. When this occurs, stulls are placed in the stope, either while the stope is advancing, or while ore is being drawn from a completed stope. In general, very little timber is required. Veins.-The quartz veins have been deposited along fracture planes in the quartz diorite. There are 20 principal veins, all of which are roughly parallel and strike at right angles to the long axis of the formation.

Jan 1, 1937

By C. E. Shoenfelt

The discovery of oil in the Powder Wash stricture in northwestern Colorado late in the fall of 1936 is the most important development in Colorado since oil was first discovered in the Moffat dome in the same county in 1923. The Powder Wash structure gives promise of developing into an oil and gas field of major proportions and is of particular interest because the oil was found in Tertiary rocks of Eocene age, which heretofore had been productive in the Rocky Mountain region of gas only, and very few of the many structures of this kind have been tested because it was believed that oil production probably would be confined to rocks of Cretaceous age only, and these were, in most instances, at excessive drilling depths. Powder Wash is one of a series of small domes in the belt of folds and faults on the south side of the large but shallow depression known as

Jan 1, 1937

By A. J. Lanza

IN view of the immense amount of attention that silicosis has received in this country in the past few years, it is timely to review the status of the silicosis problem at present. Who gets silicosis? The individual exposed to the inhalation of free silica dust. The effects upon the individual depend upon the amount of silica inhaled or, in other words, the severity of exposure, rather than upon any special variation or susceptibility among those exposed. A considerable amount of study has been given to determine what may be the role of predisposing causes in the development of silicosis. To mention one instance, at the Picher Clinic careful records were kept of all previous illnesses of the men examined as well as abnormalities present at the time of examination. Examinations of over 27,000 miners were made during the years the clinic was conducted under governmental auspices-a very fair sized sample. The general conclusions from all this work were that the incidence of silicosis is not appreciably influenced by racial, structural, or other inherent qualities; it is influenced by acquired defects-particularly as these affect the lungs. That is to say, the average run of human beings respond similarly to similar exposures to silica dust and those whose lungs are already impaired by tuberculosis or other pulmonary disease acquire silicosis more readily than those with healthy lungs. It may well be, and there is some clinical evidence in support, that negroes acquire silicosis more readily than do whites, but the infection factor has not been so carefully studied among negroes exposed to silica as it has among whites. We know that tubercle infection is more prevalent among negroes than among whites. There may be other factors concerned in the development of silicosis in negroes as compared to whites, but there is not available information upon which to base positive statements. INFECTION AND COMPENSATION Our first ideas about silicosis in this country were derived from early studies in the mining industry where the silica exposure was severe and

Jan 1, 1937

By P. W. George

This paper presents geological data regarding deposits of over 7,500,000 tons of fine-grained sulphide ore in barite gangue. A series of pyroclastics and arkoses was intruded by sills of quartz porphyry in connection with batholithic intrusions of granite 3 miles from Buchans. Gentle folding, with fracturing and shearing of tuff beds and intruded quartz porphyry, accompanied and followed the intrusion of granite and porphyry. The sulphide-barite mineralization is localized primarily in fractured and sheared tuff beds, but also in the sheared quartz porphyry. Two structures have proved particularly favorable for mineralization—one, the center of an anticline; the other, a series of weak, incompetent tuff beds intruded by thin sills of quartz porphyry and located between strong beds of arkose. During the folding the weak tuff with intruded quartz porphyry was intensely sheared and contorted and subsequently mineralized by sulphides and barite. Introduction Buchans is 5 miles north of Red Indian Lake, in Central Newfoundland, at an elevation of 900 ft. above sea level and 400 ft. above Red Indian Lake, and is reached by a 37-mile private railway from Miller-town Junction. The first ore body found at Buchans was discovered some 30 years ago in the bed of Buchans River, by Matty Mitchell, an Indian woodsman employed by the Anglo-Newfoundland Development Co. Ltd. In the years following the discovery the ore was developed by shaft-sinking and drifting, with results indicating a lenticular ore body in a shear zone, containing about 100,000 tons of extremely fine-grained sulphide ore in barite gangue averaging about 0.05 oz. Au, 4 oz. Ag, 1.5 per cent Cu, 10 per cent Pb, 18 per cent Zn. Because a profitable metallurgical treatment for the ore was not found, the mine was closed down in 1911. In 1915, Mr. H. A. Guess, Vice President of the American Smelting & Refining Co., learned of the Buchans River ore body, and after metallurgical tests had been carried on from time to time in his company's testing plant a satisfactory separation of the sulphides by selective flotation was finally effected in 1925. Prospecting for additional ore bodies was begun in 1926, utilizing geophysical methods under the direction of Hans Lund-

Jan 1, 1937

International Trade in Nonmetallic Minerals. BY J W FURNESS AND E W PEHRSON (Man &. Met, Sept, 432 2500 words) International trade in nonmetalic minerals (exclusive of fuels) is dominated largely by fertilizer raw materials such as phosphate rock, potash, nitrates, sulphur and pyrites and the miscellaneous group of minerals including asbestos, mica, graphite, fluorspar and china clay Cost of trans¬portation deters any substantial movement of the building materials which usually occur widely in nature and are thus available near consuming centers at relatively low cost This paper, which presents a summary for 1932 of the world production, consumption and principal trade relations of asbestos, china clay, fluorspar, graphite, gypsum, mica, phosphate rock and potash illustrated by world charts, is based on an original study of 15 nonmetallic minerals conducted by the U S Bureau of Mines Practical and Legal Aspects of Mme Financing See METAL MINING Economic Significance of High-grade Concentrates See MILLING AND CONCENTRATION

Jan 1, 1937

By Charles S. Barrett

Metallurgists are making use of the stereographic projection to a steadily increasing extent. In the last five years no less than 20 papers in American metallurgical journals alone have employed the stereographic projection; recent books on physical metallurgy, plastic deformation, X-rays and their applications, and crystal structure use it. Mineralogists have used the stereographic projection for many years in the description of symmetry classes and crystal planes, for it presents an accurate, easily understood plot of any angular relations in crystals with all unessential features eliminated (such as the accidentally determined size and shape of crystal faces). In metallography and physical metallurgy the projection is much used for the analysis of markings appearing on polished grains: slip lines, twins, cracks, structures formed by precipitation, magnetic-powder patterns, etch pits, etc. Data from certain types of X-ray photograms are most conveniently analyzed by its use, particularly those for determining the orientation of single crystals or the preferred orientation of grains in an aggregate. Calculations of how to tilt or cut a crystal parallel to a certain crystallographic plane or to reflect X-rays from a certain plane are rapidly carried out. It has been adopted almost universally to the exclusion of other methods by those studying the deformation of metallic crystals, save where the accuracy required is greater than a few tenths of a degree. Any directional property in a crystal or polycrystalline material can be shown on a stereographic projection; for example, the modulus of elasticity, yield point, etc. It has been repeatedly called to our attention that there is need of an elementary explanation of the principles and methods of stereographic projection, covering all the common applications in the field of metallography and physical metallurgy. The following contribution is an attempt to fill this need. The description of each method is supplemented with references to publications in which the method has been used. For convenience to the reader, these illustrative references are chiefly in American journals, particularly the publications of the American Institute of Mining and

Jan 1, 1937

By Guy N. Bjorge, A. J. M. Ross, S. J. Staple, J. D. Johnson, J. F. Wiggert

In recent years the Homestake mine has been served by three shafts, the B. &. M., the B. & M. No. 2 and the Ellison, supplemented by an inside shaft, the Milliken, extending from the 2000-ft. level to the 3200-ft. level. In 1932, when a new operating shaft was under consideration, the bottom of the mine was at the 3200-ft. level. The B. & M. and the B. & M. No. 2 shafts were down to the 1550-ft. level and the Ellison was being deepened from the 2600 to the 3200-ft. level. All ore was hoisted at the B. & M. and Ellison shafts. Levels below the 2600 level, which were under development only, were served by the Milliken shaft. Below the 1550-ft. level, the mine was served only by the Ellison shaft from the surface. Within a few years, when ore reserves above the 1550-ft. level would be depleted, operation would be limited to the Ellison shaft and the auxiliary underground shaft. The Ellison shaft alone was not adequate for hoisting the entire output from the deeper levels and also handling all men and supplies. Furthermore, assurance of safety and uninterrupted operation required two fully equipped shafts to the deeper levels. Therefore a new operating shaft was authorized in November, 1932, and was named for A. J. M. Ross, the mine superintendent. Plans for New Shaft The B. & M. shaft, begun in 1878 before much was known of the form and extent of the orebodies, was too near the ore and was endangered by ground movement. In 1924 this shaft was seriously threatened and sinking of the B. & M. No. 2 shaft, to supplant it, was begun. The latter was completed to the 1550-ft. level in 1928. In the meantime ground movement at the B. & M. shaft had practically stopped and, though loss of the shaft constantly threatened, ore hoisting was con-

Jan 1, 1937

By J. C. Mertz, C. H. Mathewson

Accurate knowledge of the solid solubilities of the elements that dissolve in the important base metals is needed for guidance in the preparation and heat-treatment of the alloys derived from these components. While there is still difference of opinion concerning the merits of the X-ray and microscopic methods of determining such solubilities, it is certainly true that the recent extensive use of X-ray diffraction to review the existing constitutional data has revealed many glaring inaccuracies and has brought about a much improved knowledge of phase-boundary locations, which will inevitably come to include all of the important alloy systems. When the work is done with all necessary precautions it appears that in the majority of cases where the solubilities extend beyond a few tenths of a per cent the X-ray back-reflection technique is capable of furnishing the best of information in this field. For the most prolonged and thorough studies it is obviously advisable to combine the results of several methods, in particular, to obtain an agreement between X-ray and microscopic data. This paper reviews the work previously done on the solubilities of phosphorus, arsenic, antimony and bismuth in copper and, in consideration of the uncertainties thus made apparent, presents new X-ray data obtained with the first three members of this group. Copper-phosphorus System Heyn and Baurl found that in slowly cooled alloys phosphorus forms a solid solution with copper up to about 0.175 per cent. Huntington

Jan 1, 1937

In the General Alphabetical and Analytical Index of A I M E Publications for the years 1926 through 1935, a complete list of the volumes covered is printed on page 5, but the dates of publication of the volumes are not given Therefore the following information regarding the volumes that were printed without numbers may be useful to users of the Index

Jan 1, 1937

By W. O. Borcherdt

THE 650-ton underground mill of The Empire Zinc Company of Colorado (a subsidiary of The New Jersey Zinc Co.) serves the Eagle mine at Gilman in the Battle Mountain mining district of Colorado. The topography is rough, the mine and mill being under Battle Mountain and the alit entrance in the north wall of the canyon of the Eagle River, which is here a steel) gorge. The town of Gilman stands on a shoulder of the mountain at altitude 8975 ft., above sea level, along the Pike's Peak ocean to ocean highway and contains the company office and the usual facilities of a modern mining town. The railway contact is at Belden, altitude 8370 ft., at the bottom of the gorge directly below Gilman, where the westbound track of the Denver and Rio Grande Western Railroad is cut along the north bank and the eastbound track along the south bank of the river. A general description of the mine, mill and service facilities, with an account of the geology, character of the ore and methods of mining and milling having previously been published in a series of articles1, this paper will discuss with as little repetition as practicable the reasons for building the mill underground rather than as a conventional structure, the methods of construction employed and the experiences gained in what is apparently the pioneer plant of this type and extent.

Jan 1, 1937

Jan 1, 1937

By E. S. Burnett, R. V. Higgins, H. C. Miller

Information obtained from subsurface pressure and ,temperature measurements in oil wells now is recognized as invaluable to geologists, engineers, and operators of oil properties. Available only during the past few years, data resulting from subsurface-pressure surveys in oil wells already have found widespread application in the estimation of reserves and in the planning of comprehensive oil-field development programs. Subsurface pressure and temperature data, together with measurements of fluid volumes produced by individual wells and specific gravities of the fluids, also are included in the fundamental information essential in studying the movement of oil, gas and water through reservoir sands to wells. Heretofore, laboratory findings were relied upon almost entirely for information pertaining to the mechanics of flow of fluids through porous media, because there was no way to check laboratory results with actual performance in underground formations until subsurface pressure and temperature instruments were developed. Laboratory and field experiments now lend themselves to closer correlation—a fact that will accelerate the interpretation of many phenomena that occur when oil and gas flow through reservoir rocks, thousands of feet below the surface of the earth. This paper summarizes the results obtained thus far in a Bureau of Mines study of certain data pertaining to subsurface pressures and production of wells producing oil and gas (and water). For wells that have been studied, flowing naturally under volumetric or hydraulic control, a simple relation has been found between the mass rate of fluid (oil, gas and water) production and the corresponding drop in pressure in the reservoir sand. The equated relation embodies a productivity factor or "index" expressed in terms of mass rate of fluid production per pound drop in pressure through the sands. The equation as developed is an expression of the ability of a well to produce, which permits comparison on a uniform basis of the productivities of different wells. The study shows also that over the range of observed data a productivity factor

Jan 1, 1937

By W. R. Ingalls

In reviewing the history of the metallurgy of zinc, I shall pass hastily over what is only of antiquarian interest. That has been excellently treated by Dr. Bernhard Neumann in "Die Metalle" (1904) and has been described briefly in my "Production and Properties of Zinc" (1902), in my "Lead and Zinc in the United States " (1908), and in other metallurgical works of more or less the same date. In this present monograph, I have it in mind to confine myself mainly to technical practice, especially to that of the last 75 years, prior to which period advance was slow and of no great moment. The ancients made brass by the cementation process, i.e., embedding copper in a mixture of calamine and carbon and heating, whereby zinc oxide was reduced and zinc was vaporized and combined with the copper. Zinc was isolated by some of the alchemists, who named it and knew something of its properties, but made no use of it. Long before then, however, zinc was produced in India. Later it was produced in southern China. Possibly the Chinese obtained their knowledge from India. The Chinese in remote places still produce small quantities of zinc. I have seen photographs of their furnaces; or pots, for they hardly deserve the dignity of being called furnaces. I imagine that they are the same that were used centuries ago, for I cannot conceive of anything more primitive. Anyway, it is certain that the idea of a commercial production of zinc in Europe was imported from the Orient, where the metal was known in commerce as Speauter and Spiauter, whence speltrum and finally our term spelter. Tutanego and Tuteneague are other old names. Dr. Isaac Lawson went to China about 1730, expressly to discover the method of its production. What connection there was between Isaac Lawson and John Champion we do not know, but the latter obtained in 1739 a patent for a process of distillation downward and at some time between 1740 and 1743 erected a works at Bristol and actually began the manufacture of spelter. A production of 200 tons per annum is mentioned. In about the year 1766, Rishop Watson visited the Champion works and saw the process in operation, which previously had been

Jan 1, 1937

By John F. Kendrick, Paul D. Cornelius

This paper is a progress report of a study the authors are making of the sucker-rod pump, considered as a vibrating system with one degree of freedom, with forced vibrations and with viscous damping. Dr. S. Timoshenko's formula is given, defining such a system. Each factor is considered in respect to the problem of operating sucker rods, and the zone is pointed out in which the mathematics do not apply to the sucker-rod pump, because of its variable mass. This general theory is interpreted in the light of nearly two years of testing wells in the field, and correlating the results of other tests. The motion of the pumping mechanism is a vibration. The string of sucker rods vibrates with a natural frequency. The motion of the plunger is the result of adding together these two vibrations, and is modified by a damping or friction factor. The controlling factor appears to be the ratio of the period of the natural vibration of the rod string to the period of the vibration of the pump. The first conclusion is that a definite value of this ratio, which is below resonance and is probably not greater than 0.5, should not be exceeded in order to assure satisfactory performance from the sucker rods. The second conclusion is that the component parts of the pumping equipment should be selected to give the smallest practical period of the natural vibration, and when this does not permit operation at a safe speed and give the required plunger displacement, a longer polished-rod stroke should be used. While the quantitative results are but rough approximations, the qualitative analysis of pumping problems on this basis promises to be of considerable value in diagnosing the cause of poor performance and prescribing suitable remedies. The trouble that results, whenever it becomes necessary to crowd the sucker-rod pump, to take potentials or to handle increasing volumes of water, is responsible for the belief that this type of pump is not equal to present day needs, and that it is only a question of time before some other pumping device will take its place. Of the troubles experienced, it is not surprising that the frequency of sucker-rod failures should

Jan 1, 1937

By Eugene A. Stephenson

The writer apologizes for presenting this very elementary analysis of one aspect of proration, but a search of the literature failed to disclose any concrete illustrations of the effect of various proration formulas upon the allowable oil produced by tracts of different sizes. Many engineers have doubtless made somewhat similar calculations and are fully acquainted with the results. The various allocation formulas that are in use are based on one or more of the following factors: (1) wide-open well potential, (2) potential through an orifice, (3) uniform well allowable, (4) acreage, (5) sand thickness, (6) bottom-hole pressure, (7) productivity index, and (8) volumetric displacement. Of these, the unrestricted potential formula, or open-flow test, and the uniform well allowable are commonly regarded by engineers as those least likely to give each producer his proportionate share of the oil or gas, as represented either by acreage or by sand thickness, or both, except when the wells are located on tracts of large size. Unless the mechanical equipment that may be used during the potential test and the method of taking the test are both specified, the net result of the potential formula is to practically force the operators to use special equipment and adopt special procedures prior to and during the potential test, so as to secure the largest possible allowables. Much ingenuity and skill have been devoted to this,problem, but the general effect is to permit excessive allowables for very small tracts, and stimulate unnecessary drilling. It is interesting to compare some of the high yields from the Wilcox horizon at Oklahoma City with each other, as an illustration of the effect of an allocation factor based solely on potential (Table 5). One of the glaring instances is a well on a ½-acre lease, which had produced, as of September 1936, at the rate of almost 3,000,000 bbl. per acre. This is at least twice as many barrels as could have been present under the property if the reservoir had consisted of a tank of oil 200 ft, deep and 56 acre in area. Numerous combinations of acreage, potential, bottom-hole pressure, sand thickness, etc., have been proposed and are in use in various fields.

Jan 1, 1937

By J. Ruzicka

In creep testing, material is subjected to a constant load, preferably at a constant temperature, and its rate of deformation is measured. The method of loading can be of various types but in this paper only creep testing under tensile load will be considered. The ordinary tensile test is essentially a comparison test in conditions that frequently hear little or no relation to those under which the test material is to be used in service. The purpose of creep tests is to measure the strength of the test material at slow rates of deformation that more nearly approach the rates realized in service. One purpose of this paper is to illustrate that the creep test, in addition to its value as a service test, is superior to the ordinary tensile test as a sensitive tool for the comparison of certain metals in investigative testing. The other purpose is to describe equipment having distinctive features of design that make it especially suitable for such tests. Representative data obtained with this equipment on a group of rolled zinc-base materials are given. These data are compared with those from practical comparison tests of the creep type on weatherstrip fabricated from the same group of materials. The comparison illustrates the value of the fast creep test and of the equipment. The Equipment The creep equipment consists essentially of a tank containing a constant-temperature oil bath in which the creep of 14 specimens, loaded by means of levers, is measured by means of one movable extensometer. Figs. 1, 2 and 3 illustrate its general construction and appearance. Constant-temperalure Oil Balh.—A common constant-temperature bath requiring only one temperature-controlling equipment for a number of specimens was chosen as the best means of fulfilling the requirements of low cost and compactness. In addition, this allows the testing of a group of specimens under identical temperature conditions.

Jan 1, 1937