Search Documents

By E. S. Machlin, C. W. Chen

THIS investigation is concerned with the origin of the intercrystalline voids and cracks formed in metals and alloys subjected to stress at elevated temperature. There have been many suggestions in the recent literature relating to this problem. Greenwood' suggested that the voids may be produced by vacancy condensation. Zener has stated that shear-stress relaxation across grain boundaries could initiate high tensile stresses at the regions blocking grain boundary slip and thereby cause the formation of cracks. Chang and Grant3 have described the formation of cracks at grain boundary triple points and have experimentally verified Zener's mechanism for the grain boundary regions in the vicinity of a triple point. Subsequent to the completion of this investigation, Gifkins4 developed a model which made use of Stroh's5 mechanism of fracturing to produce sub-microscopic fractures that subsequently grow by grain boundary slip. Chen and Machlin,6 in answer to Gifkins, described a model deduced from the present investigation, in which grain boundary slip provides both the stress to fracture at grain boundary jogs and the deformation required to separate fractured jog surfaces. The possibility of gas condensation to form intercrystalline voids and cracks is eliminated as a basic mechanism because such voids and cracks are developed in vacuum melted material containing minute amounts, if any, of gaseous impurities. In a theoretical evaluation of this problem, Machlin7 concluded that void nucleation by vacancy condensation during creep-rupture is improbable but that vacancy condensation on supercritical sized voids to produce growth is probable. This investigation was begun to evaluate the suggested mechanisms for intercrystalline fracture. In particular, in order to correlate vacancy supersaturation ratios produced in creep with those determined by Bal-luffi and Seigle8 as critical for , the nucleation of voids, specimens were obtained from the same heat of brass as used by the latter authors, through the courtesy of Dr. Seigle. The experiments conducted in this investigation fall into the following categories: 1) Brass—observation of voids produced under a variety of conditions, including creep under compression, to evaluate the mechanisms of void nucleation and growth. 2) Bicrystal experiments to check the mechanism of void nucleation deduced in this investigation. 3) Morphology of intercrystalline voids produced in a variety of metals. Each set of experiments will be described and discussed separately. Experimental Techniques A special creep-rupture test rack was constructed which made it possible to apply the stress to the specimen in a controlled atmosphere of inert gas, reducing gas, or vacuum. All the creep-rupture tests on a-brass (30 pct Zn) were conducted in nitrogen under a pressure slightly above atmospheric. Either dead weight loading or constant elongation rate loading could be applied with the load measured by means of a strain gage dynamometer. In order to obtain a coarse-grained crystal structure stable at

Jan 1, 1958

Jan 1, 1908

By Alan English

INTRODUCTION During the Bicentennial Year in the United States of America, recognition should be given to the fact that 20 years ago the first large-scale commercial pelletizing plant was started and attained rated capacity. This was the beginning of a new industry. Twenty years ago the total production of pellets was principally from pilot plant facilities and totaled in the thousands of tons per year. At the present time the world production is slightly in excess of 280 million tons per year. This truly is a tremendous growth for any industry. Such a production growth obviously is accompanied by a similar growth pattern in the development of process, equipment, and facilities. During the growth and development period, different materials became more adaptable for processing. For example, initially the pelletizing of iron ores revolved around the magnetite concentrates where the heat of reaction constituted a very important part of the process fuel. During this growth period, specular hematite, earthy hematite, mixtures of hematite and magnetite, and even non-ferrous type materials were pelletized, a function previously thought not practical. The demand for the use of pellets has also broadened their concepts. At first they were made to replace the high-grade iron ores used in blast furnaces. Nowadays, not only have they replaced iron units, but they have had a major influence on the design of larger blast furnaces and have contributed to production rates in excess of 10 000 tons per day from a single furnace. They have also been used in the manufacture of steel, principally for coolants in the BOF practice. More recently, with the improved beneficiation techniques that have been developed over the same period of time, pellets have been used for the direct reduction process and can be used directly

Jan 1, 1977

By G. S. Hume

The production of petroleum in Canada is relatively small in proportion to the amount of oil consumed. Production figures are given in Tables 1 and 2, which show that the production in Alberta for 1934 was more than for the whole of Canada in 1933. The production of natural gas for Canada is shown in Table 3, In Turner Valley, the largest producing gas and oil field in Alberta, seven naphtha wells from the Paleozoic limestone and one crude oil well from Lower Cretaceous strata were completed during the year. Six-

Jan 1, 1935

By David R. Mitchell, R. B. Hewes

MANY processes for cleaning coal that are in use depend primarily on physical properties of coal and refuse other than specific gravity and surface conditions relating to froth flotation. These properties are shape, coefficient of sliding friction, resilience, friability, magnetic susceptibility, and electrical conductivity. In many of these processes specific gravity does have some effect and many separators are designed to utilize more than one of the physical properties cited. Although the processes described herein do not have a widespread application, yet for specific coals and specific conditions, they are economically important. A problem confronting many coal-mining districts is the marketing of the slacks or screenings and dust passing the final sizing screens. Processes in commercial use installed primarily to increase the form value, and hence the market value, of these slacks and dusts include briquetting, packaging, and low-temperature carborization. MECHANICAL PICKERS Machines utilizing shape, fictional resistance, and differences in resilience of coal and impurities are usually called mechanical pickers. They require a closely sized feed, therefore their use is confined to the pea, nut, and egg sizes. Various types of these devices are described by Berrisford, 1, 2 Taggart, 3 and Peele. 4 Shape In general, coal differs in shape from its accompanying dirt throughout the range of commercial sizes. Coal, breaking into roughly, cubical particles, contains a greater number of axes that are approximately the same length than does the dirt. The latter, consisting of pieces of slate and shale and lenses of pyrite, is flatter in nature. Further, flat coal often has a dirty, slaty appearance, even though of high quality. Mechanical pickers known as flat pickers, or "flatters," are widely used in the Pennsylvania anthracite region to remove flat coal from the final clean coal. This practice greatly improves the appearance of the final market product.

Jan 1, 1943

P. Herasymenko (New York University, New York) —The authors' experiments on equilibria between water vapor and liquid synthetic slags represent a valuable contribution to our knowledge of the nature of liquid slags. They can be regarded as a proof of ionic splitting of water molecules dissolved in slags. The assumption that water dissolved in slag was com- pletely ionized was made in my report on hydrogen equilibria in steelmaking as early as 194010. In that paper, the first systematic data were given on the content of ionized hydrogen in acid and basic open-hearth slags. The paper probably escaped the notice of the authors, although they mention the articles published later by other investigators who reported erratic and

Jan 1, 1958

By Samuel G. Lasky

FAULTING at Kennecott, with its attendant fracturing, is unusual, complex, and important. As study and knowledge of the various fault systems have progressed, appreciation of that importance has helped in the selection of proper horizons for exploration and in the avoidance of useless crosscutting and drifting. During the study of this faulting and fracturing, a suggestion concerning the formation of the ore-bearing fissures occurred to me. Further study in the available portions of the approximately 45 miles of workings in the Kennecott mines for the purpose of checking up the the suggestion led to the hypothesis which this paper will attempt to present. Briefly, the hypothesis may be stated as follows: The formation of transverse faults that stop against a main system is connected with changes in the strike or dip of the main fault, and such cross faults or fractures lie in the moving block of the main fault system and indicate a change in strike or dip of the main fault. It has been found that each kind of change tends to produce definite effects and that careful study of the evidence can often suggest the exact type of change. Outline of Kennecott Mines Geology The mines at Kennecott are on the northeast flank of a broad anticlinell where erosion has exposed the Upper Triassic Chitistone limestone resting conformably on the Permian or Triassic Nikolai greenstone.2 These two are the only formations exposed in the immediate vicinity of the mines that bear relation to the ore deposits. The Nikolai greenstone is a series of altered basaltic lava flows, the actual thickness of which is unknown. The Chitistone limestone is the ore-bearing formation. At its base is a bed of about 5 ft. of red, green, or black shale which shows strong evidence of movement wherever it is exposed underground—one of the

Jan 1, 1929

By Earle Schumacher

COPPER-CALCIUM alloys are of interest as materials for use in deoxidized conductors of high conductivity. That calcium is effective in deoxidizing and degasifying copper is well known. Brandenberg and Wiens1 have described the use of calcium in the casting of sound copper and state that the deoxidation can be carried out without difficulty. The castings that they prepared were sound and sufficiently ductile to permit wire drawing. Pratt,2 in British Patent No. 1699 (1907), has claimed the use of calcium for the deoxidation and degasification of copper. Masing3

Jan 1, 1929

By E. A. Gulbransen, W. S. Wysong

THE behavior of molybdenum and its surface oxides in oxidizing and reducing gas atmospheres and in high vacua at elevated temperatures is a question of scientific and technical importance The use of molybdenum as a metal or as an important component in alloys in oxidizing atmospheres at elevated temperatures has been limited because of the unprotective nature of its oxide film and the volatility of this oxide at moderate temperatures. This communication will present results of a vacuum microbalance study 1,2 of the following problems. (11) the oxidation kinetics in the temperature range of 250° to 450°C; (2) the reduction with pure hydrogen of thin oxide films formed on molybdenum; (3) the volatility of the thin oxide films, and (4) the vacuum oxidation of molybdenum at high temperatures. Molybdenum is an interesting metal to study for the following reasons: (I) although the oxide-to-metal-volume ratio is greater than one, the metal is not considered protective; (2) the metal oxidizes readily at temperatures of 250°C and higher; (3) the oxides of the metal are reduced at temperatures as low as 500°C by pure hydrogen; (4) the oxide MoO3 melts at 795°C; and (5) the oxides of molybdenum are volatile at moderate temperatures. The following variables are studied in the oxidation kinetics. time, temperature, pressure, surface preparation, surface area, concentration of inert gas in the lattice, cycling procedures in temperature, vacuum effect and high temperature vacuum oxidation The general interpretation of many of these factors has been previously discussed. LITERATURE The oxidation of molybdenum has not been studied critically. Although" many studies have probably been made on the kinetics of the oxidation process, none has been reported in the literature available to us. The crystal structures found in the oxidation of molybdenum have been studied by Hickman and Culbransen 4 Their results showed that MoO2 is the oxide which is stable in contact with the metallic subgtrate throughout the temperature range 300 to 700°C. As the film thickens in the low temperature range, MoO3 becomes predominant on the surface. Above 400°C, Mo03 is no longer observed, Mo02 being the only oxide found. Hagg and Magneli5 have shown from an X ray study that the a-phase, orthorhombic MoO3 is stable up to 1050°C. Two other phases, ß and ß', with compositions close to Mo02 90 are also obtained The formula for the ß phase is not given but that of the ß' phase is defined as Mo9026. The ß' phase is found to be built upon a monoclinic unit cell. A -?-phase is isolated from a preparation M00275 heated for 17 hrs at 670°C. This phase is

Jan 1, 1947

United Engineering Trustees, Inc. ARTHUR S. DWIGHT GEORGE D BARRON J V. N DORR Engineering Societies Library Board ROBERT PEELE PHILIP W. HENRY GEORGE C STONE JOSEPH E. POGUE The Engineering Foundation H C BELLINGER GALEN H CLEVENGER J V N DORR

Jan 1, 1923

By R. H. Wightman, C. D. Chandler, P. B. Nalle

SURFACE quarrying at the Crestmore Div. of Riverside Cement Co. in California was started in 1909. In the early 1920's it was considered that these deposits were nearly exhausted for the equipment available at that time, and in 1927 the company began a block caving system. This mine continued operating until February 1954. In 1941 trucks and crawler-mounted shovels had reached a stage of development that permitted reopening the quarries in conjunction with the underground mine. In 1948 surface reserves and the well developed limestone of the caving system neared depletion. To go deeper with the caving system was unattractive because of the economics, changes in physical structure of the rock at depth, and the perched water table

Jan 4, 1957

By W. C. Hagel, H. J. Beattle

DURING an earlier examination of high-temperature alloy, A-286, the presence of an unknown intermetallic compound was verified by X-ray diffraction. Owing to its prominent appearance at grain boundaries, the arbitrary name of G phase was assigned.' Low-silicon, vacuum-melted heats were found to contain no G phase, and this investigation was initiated to determine the influence of silicon on G-phase formation; additional work was undertaken to extend existing data on other intermetallic compounds and the aging reactions in this group of alloys. Taylor and Floyd2-4 observed that the Ni3Al phase (y') and the Ni8Ti phase (7)) are the only equilibrium intermetailic compounds in nickel ternary alloys containing up to 25 pct Cr and 10 pct Ti or Al. They found that y' can dissolve considerable nickel, chromium, and titanium, although the stoichio-metric composition of 7 remains fixed. Nordheim and Grant5 confirmed that age hardening of 80 pct Ni-20 pct Cr alloys of the Nimonic-80 type is due to precipitation of y', where aluminum is partially replaced by titanium. They suggest that optimum hardness and ductility result from increasing the titanium to aluminum ratio toward the end of the y' solubility range and from increasing total titanium and aluminum content to the maximum limit permitted by processing. Such information is necessary for those seeking to improve the service-temperature range and long-time structural stability of high-temperature components. Experimental Methods Compositions of materiais studied. are listed in Table I. Alloys D, E, and F possess representative A-286 analyses; silicon increases from less than 0.02 to 1.75 pct in alloys A to H; in alloys I to K, titanium decreases from 2.24 to 0.39 pct, and aluminum increases from 0.1 6 to 240 pct. Alloys A and D were solution heat treated for 4 hr at 1700°F, oil quenched and aged for 0.5, 2, 6, 12, 30, 70, 200, and 1000 hr at 1200°, 1300°, 1400°, and 1500°F. Therefore, a total of 33 specimens was required for each

Jan 1, 1958

By Joseph Jensen

FROM Aug. 31, 1937, until Apr. 30, 1939, there were 40,872,610 bbl. of oil run to storage in California; from Apr. 30, 1939, to Aug. 31 of the same year 5,512,912 bbl. were withdrawn from storage. But from Aug. 31, 1937, to Aug. 31, 1939, the number of producing wells in the state has increased from 17,706, with a potential production of 1,323,202 bbl., to 18,910, with a potential of 2,302,282 bbl. Thus, in a period of two years, during the first 20 months stocks increased over 1/3 and during the following four months stocks decreased 1/30. In the same two years the number of productive wells increased 1/15 and potential increased 3/4. Undoubtedly, the large increase in stocks created the pressure that caused the reduction in stocks that followed; yet this has come about in spite of the larger number of wells and higher potential. Cause of the change was the adoption on May 17, 1939, by the Central Committee of California Oil Producers of a uniform method of oil curtail-ment for all wells throughout the state. Acceptance of the method in the four months following adoption by practically all fields in California indicates that producers generally are convinced of its merit and fairness. True, some operators still overproduce, but the restraint practiced by the remainder of the industry has been sufficient to turn a situation headed for chaos into one of reasonable stability. Credit for this change goes to the industry itself, because it has all been accomplished under voluntary oil curtailment.

Jan 1, 1940

By T. F. Archbold, R. E. Grace

The use of interference colors is the simplest experimental way to determine the approximate film thicknesses of oxides formed on liquid metals. A large amount of data under various conditions can be obtained easily and quickly. The oxidation of liquid lead has been studied by several investigators,1-5 but all of these studies have been on thick oxide scales. The purpose of- this work was to investigate the range 0 to 2000A film thickness. By using electron diffraction, Jenkins concluded that the surface of the film on molten lead is yellow orthorhombic PbO with the (110) planes parallel to the surface. This was confirmed by Shimaoka and Yamai7 who also used electron diffraction from the melting point of lead to 730°C. The rate of oxidation of pure liquid lead in air was measured in the temperature range 453" to 643°C by observing the rate of formation of interference colors on static lead baths. Approximately 170 g of lead (99.999 pct) was placed in a refractory dish having a working surface of 13.8 sq cm. This crucible was placed in a deep-well resistance furnace open to the atmosphere. The times at which the various interference colors appeared, after wiping the molten metal surface clean, were determined at 453", 533°, 600°, and 643°C. Elapsed times were determined with a stopwatch and all colors were estimated by eye. Bath temperatures

Jan 1, 1959

By Gordon M. Matheson, Charles V. Logie

The current state-of-the-art design of mine pillars can be grouped into empirical and numerical design techniques. Numerical design techniques are based on sophisticated computational techniques which analyze the stresses and strains through the interstices of a pillar. Empirical techniques are less exact, but have been widely used, particularly for coal mine pillar design, because of their ease of computation. Over the years numerous empirical equations have been proposed to calculate the ultimate strength of coal mine pillars. This paper presents a review of the various equations which are most frequently utilized and examines the fundamental assumptions, limitations and applicability of the design formulae. The review intends to provide the practicing mining engineer with an understanding of the assumptions and mathematical basis of each equation to aid in the selection of the criteria most applicable to his specific design problems. Recommendations are made of the empirical equations that are presently most acceptable for design.

Jan 1, 1983

By E. W. McAllister

THE decision of the California Oil Umpire's1 office to accept well potentials established from subsurface-pressure data has brought to the attention of many operators for the first time the application of such data to production problems. This paper reviews the development and application of subsurface-pressure data in Kettleman Hills, where these data have been used in production work since 1932. The Kettleman Hills field was discovered in October 1928. The first subsurface-pressure surveys were made early in 1932 and by the middle of 1933 the two major operators in the field were making routine pressure runs in their respective wells. Shortly thereafter, these companies agreed to exchange pressure data, and later a third company entered into the agreement. This made it possible to analyze the effects upon the reservoir pressure of past production practices, which are discussed in the latter part of the report. It is interesting that many of the applications of subsurface-pressure data discussed herein were anticipated by C. L. Clarks and C. B. Kimberlin‡ in a reports dated March 1933. PRODUCTIVITY INDEX In the majority of individual well problems involving the use of subsurface pressure data, it is necessary to use a factor known as the "productivity index," which indicates the ability of a well to produce and represents the number of barrels of oil or oil and water per day that will enter the well bore for each pound per square inch pressure drop made opposite the producing interval of the well. The productivity index may be determined from pressure and production data for one or more rates of flow and a static or shut-in pressure survey or from production and pressure data for two or more rates of flow. Productivity indices may be based upon either net oil or total fluid production. All indices referred to in this report are based upon net oil. The value of the productivity index for Kettleman Hills wells decreases generally with time and it is not uncommon for the index to vary in value at any specific time for various rates of flow. The decline of the productivity index may be attributed partly to the loss of reservoir pressure. As. the reservoir pressure decreases, gas originally in solution is released from the oil, congesting the flow of fluids through the formation and increasing the viscosity and surface tension of the oil; thus the flow resistance of the fluids through the formation is increased, resulting in a decrease of the productivity index. For convenient reference, the productivity indices for each well are plotted against time and a curve is drawn through the points showing the trend of the average index value. Plotted on Fig. I are index values for five

Jan 1, 1941

By William H. Emmons

The problem of the metalliferous veins has always been an outstanding one in the science of ore deposits. In recent years interest has been stimulated by Spurr, who maintains that veins have consolidated from magmas that have densities as great as the densities of ordinary rocks. Lindgren published a noteworthy paper1 in 1926, in which he supports the theory that veins are deposited chiefly by hot waters. Lindgren's paper was discussed by Singewald, Spurr, Kemp, Anderson, Colony, Bateman, Porter and others. The discussion, in the main, was centered on the interpretation of fragments that are included in veins. This paper also treats the problems of fragments in veins and includes a reply to a review by Spurr2 of a bulletin by Larsen and myself3 published by the United States Geological Survey on the geology and ore deposits of Creede, Colorado. Mineral veins containing fragments of the wall rock are common. At many places the fragments are completely isolated, one from the other, and are entirely surrounded by vein matter. It has been stated that the vein matter around the fragments was heavier than the fragments and that the latter were floated in a magma. J. E. Spurr, who is the leading advocate of this hypothesis, 4 urges that normal mineral veins were deposited by solutions heavy enough to float fragments of the country rock, and it is mainly on this relation that he bases his theory that veins are deposited by solidification of magmas. If it can be shown that vein-forming solutions have a specific gravity greater than rock (2.77), one is justified in regarding them as true mag-matic solutions. It is shown later in this paper, however, that at Lead, S. D., water not more highly concentrated than ordinary drinking water is depositing vein matter around fragments of schist and of steel in such a manner that the fragments are completely isolated and completely surrounded by the mineral cement.

Jan 1, 1928

By Charles H. Addison, Robert W. Shields, James W. Sweeney

GIPSY: Is user oriented. Is flexible in applications. Is an ITERATIVE question answering system. Has an adaptable retrieval mechanism. Has both a batch and a teleprocessing version. Allows the user to "browse" through his information. Has ability to answer "ad hoc" queries. Is a currently working and proven system.

Jan 1, 1969

By Alan F. Stewart, Douglas R. Piteau, Dennis C. Martin

Three examples of open pits where toppling failure controls the stability and design of the slopes are described. Two examples involve the design of overall slopes in base metal mines. The third example concerns the analysis and design of remedial measures to prevent toppling failure from occurring in a critical slope in a coal mine. The analytical techniques for assessing toppling failure on a rational basis are discussed for the three examples. This includes an assessment of the important parameters which govern the stability for the toppling failure mode. The geological setting and input data for each example are described, as are the important external or limiting factors pertinent to the sites in question. A statistical cumulative technique was used to assess one of the most important input parameters in the two examples involving overall slope design. Both deep-seated toppling failures, involving the entire slope, and shallow bench failures are considered. Results of the stability analyses and their related engineering significance with regard to slope stability and design are discussed. A sensitivity analysis of various parameters is effectively utilized. Design charts are developed and evaluated accordingly. In the example where toppling failure was unavoidable, the rationale for design of stabilization techniques to prevent toppling is discussed.

Jan 1, 1983

Jan 1, 1963