Search Documents

By Van C. Nyman

A time-sharing computer was tied in to Hecla in August of 1967. This has proven to be helpful in performing metallurgical and engineering calculations that were formerly tedious tasks. Metallurgy programs were written for applying two and three product formulas. Programs were expanded to make the monthly metallurgical balance calculations for each of the Hecla mills. The Hecla engineering department uses the computer for solving hoist duty cycles and for traverse analysis. Both Asarco and Bunker Hill Company in the Coeur d’Alene Mining District are tied to a time-sharing computer. Their uses for the time-sharing computer will be discussed. Asarco had the advantage in learning computer techniques during an extended strike. A comparison of Asarco computer use with that of Hecla's will show the advantage in having a person or persons spend full time on the use of computers. Bunker Hill has the versatility of five teletype units in their mine-smelter complex plus ability to tie in to their own computer.

Jan 1, 1969

By Charles W. Eichrodt

So much has already been wimitten on this vast subject of ground movement and subsidence, and so many data collected and commented upon, that in this paper the author proposes to confine himself to the submission of some plans showing what has actually occurred in the mining of several of the orebodies which have come under his direction during the last 20 years or so at Rio Tinto, Spain. Some notes are added for the purpose of describing the plans. The author does not attempt to give his opinion as to the reasons why the subsidences have occurred in the manner in which they are found, but confines himself to giving as true a picture as possible of the movements that have taken place. Effects of Excavation on Ground Movement Broadly, the effects of excavations on the overhead or adjacent ground can be classified under three headings, as follows: 1. Ground movements due to excavations made from surface only, such as those made in opencasts where no excavations underlie them. The stability and strength of the ground to resist movement must determine the slopes. 2. Ground movements due to underground excavations only; i. e., where the surface is not removed. 3. Ground movements due to a combination of both; i. e., from excavations taking place from the surface for the purpose of stripping an orebody and recovery of the ore to a certain horizon combined with excavations being carried out below, at the same time, for the winning of the ore below the horizon at which mining by stripping or opencasting under the specific conditions is no longer economical. Nos. 1 and 2 represent independent and distinct problems and No. 3 is a combination, which presents results much more difficult of explanation. The accompanying plans and sections give examples of what has occurred under the three conditions. Unfortunately, the class of ground is not exactly the same in them all, but the difference is not greater than is generally encountered over districts of equal area. Excavations from Surface To illustrate No. 1 three cross-sections are shown, of excavations made for the stripping and excavation from three different orebodies

Jan 1, 1930

By R. Laird Auchmuty

FOREWORD THE A. I. M. E. Subcommittee on Bituminous Mining has been trying for several years to secure the information that was collected by the Marquette Cement Manufacturing Co. on the subsidence of its property caused by mining coal beneath it. The Marquette company was willing to have these data used, but it was impossible to obtain them because the records had been filed away. About two years ago these records became available and the engineering data presented herewith were compiled from them by R. L. Auchmuty, assisted by L. E. Young, who was connected with the collection of the information. On account of the cost, it is impossible to reproduce all of the data here, although the original information is on file with the records of the Committee on Ground Movement and Subsidence. The accompanying charts show representative and average data and give only the engineering information with enough description to tell how it was obtained. It is hoped that all of those connected with the original case will participate in the discussion that this will bring forth. HOWARD N. EAVENSON, Chairman, Subcommittee on Bituminous Coal Mining.

Jan 1, 1931

By Harlowe Hardinge, R. C. Ferguson

Oscar Johnson—In my opinion, the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. Comparing the entire groups of operators with those who have had the opportunity to make slow-speed mill studies, I think you will find the latter small in numbers. Most managers want the equipment worked to its maximum output. There are, however, some installations where plant and mill sizes are such that they can do the job with reduction of mill barrel speeds. The past and the present installations of the industry are laid out to get the most capacity for the least capital outlay. This is the case even with the plants of Chile Exploration, International Nickel, Morocco, and Anaconda, now under construction or being changed. The industry recognizes that most all equipment it buys today is good and can be depended upon for efficient performance. Under this scheme of things, I am doubtful that slow-speed ball mill operation will be generally applicable. With reference to the U. S. Bureau of Mines laboratory tests, I think table II could have been omitted. It is inconclusive as to maximum efficiency for the low-pulp level mill on hard ore. There should be no question about this point. However, data on mill speeds can be found to substantiate various theories as well as refute them. Gow, Guggenheim, Campbell and Coghill, in their paper on Ball Milling,' believe their 2 x 2 ft laboratory mill reflects results that can be expected from large mills. If so, then referring to their table 11, they state, "The conclusion to be drawn from this second series is that high speed, not exceeding 72 pct of the critical, favors capacity, as before, but that with proper conditions of operation high speeds may give as good efficiency values as low speeds. In this case the efficiency values are nearly constant. A horizontal curve would indicate that the amount of grinding was directly proportional to the power expended, and these tests suggest that such a coildition can be made to exist in commercial operations." Table II (From Paper by Gow et a1)2 Speed. Pot Critical 32 42 52 62 72 82 Capacity: Surface tons per hr (65- mesh) 266 42.1 54.4 65.9 74.3 74.1 Surface tons per hr (200- mesh) 56.1 87.4 112.7 137.1 154.2 153.0 Efficiency: Surface tons per net hp hr (65-mesh) 35.7 36.3 36.3 35.4 34.3 32.3 Surface tons per net hp hr (200-mesh) 75.3 75.3 75.1 73.7 71.0 66.0 Ore in mill, 1.b. 98 100 100 113 122 165 The field performance data, table 111, represents much effort in its collection and preparation. But, one must realize that there are many variables that effect the efficiency of grinding mill operation, and too much must not be assumed as to the effect of some specific change. Possibly with changes in mill speed, the results might be more consistent by also a change in ball rationing, type of ball, volume of ball charge,. p.ulp level and amount of pulp in the mill, pulp consisting, design of liner, circulating load, etc. Also, changes in ore character must be reckoned with when evaluating grinding performance. At present the Climax Molybdenum Corp. is running at much reduced capacity. Mr. James Duggan informs me that at mill speeds of 17 rpm, they save a $0.025 per ton on liners and $0.025 per ton in power, but, if the demand for molybdenum increased, he would go back to higher speed to obtain maximum tonnage, as the values from the increased tonnage would far more than offset the one half saving at the slower speed. The Jnspiration ran a six months' test between mills running 21 rpm and 23.5 rpm. The slower mills ground 10 pct less ore with a slight saving per ton, but when the reduced plant tonnage was checked back into the actual cost figures of concentration, the high-speed mills with their greater tonnage showed considerable advantage. To be convinced of possible practical results from the predictions in the conclusions, I think we would have to rely on the analysis of expert cost accountants to furnish the necessary proof figures. Hardinge and Ferguson are to be commended for the work in preparing this paper. I am convinced that our Massco engineers should go into higher speeds with our equipment. Harlowe Hardinge (authors' reply)—For one, I heartily agree with Mr. Johnson's opening statement that the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. It was on this basis and for this reason the paper was written. Mr. Johnson, on the other hand, takes the position that, on the whole, low speeds are not justified from the economic standpoint, basing his principal reason on the fact that lower mill speeds cut mill capacities and hence reduce the gross income from the product produced. There is no denying this point. It is almost axiomatic. It is for this very reason that the overall advantage of lower mill speeds has been discounted and even overlooked. It was for this reason mainly that the paper was written in the first place. It is one thing to plan an efficient operation at the outset, basing one's figures on the tonnage requirements at the time, and it is quite another to be confronted with the problem of increasing the output of an existing installation at a minimum of capital expenditure. Economic consideration of a new installation is greatly influenced by referring to an old one. Too often, the analyst assumes that if this practice is followed in the new installation, one would not go wrong. It is just here that he may be wrong. Past practice and low capital expenditure are all too frequently given priority over the engineer's analysis of operating costs. When we are able to start fresh, we should give proper weight to other economic factors which do not exist in an old installation. It is these economic factors that make it possible to spend at the outset just a little more money and get it back in a matter of months and effect big savings for years to come. F. C. Bond—This paper is of considerable importance in that it emphasizes a modern trend to operate ball mills at somewhat slower speeds than formerly. We have checked the data in the paper with that obtained

Jan 1, 1951

By Herman Blumenthal, Ronald Silverman

lnfiltrability of a porous Tic compact, produced by powder metallurgy technique, depends on the capillarity of the compact and the surface condition and nature of the individual particles. Capillary forces raise the liquid metal infiltrant into the interconnected pores of the compact and the complete filling of these pores is a function of their geometry as well as the wettability of the Tic particles. The paper deals especially with the improvement of this wettability through surface conditioning of the Tic particles. INFILTRATION, a technique for preparing dense powder metallurgy parts by filling the void spaces of a porous body with a liquid metal, has been used for the manufacture of titanium carbide-base cermets. Although the infiltration process was

Jan 1, 1957

By G. K. Manning, A. R. Elsea, C. R. Simcoe

Boron increases the hardenability of hypoeutectoid steels by decreasing the nucleation rate of ferrite and bainite. It is postulated that concentrations of lattice imperfections, such as exist at the grain boundaries, furnish the necessary energy for nucleus formation. Boron, because of its atomic diameter, will concentrate at lattice imperfections where sites of suitable size are present. Boron will decrease the energy of these local areas by occupying these sites. This mechanism accounts for the large increase in hardenability observed with small amounts of boron. The loss of the boron hardenability effect and the boron precipitate formation are explained on the basis of increased concentration of boron at the grain boundaries either with increasing boron content of the material or with increasing temperature. COMMON alloying elements affect both the nucleation and growth rates of the austenite decomposition reactions.' This effect is largely a result of the slow diffusion rates of these elements. Although a small addition of boron markedly increases the hardenability of steel, the diffusion rate of boron, which is of the same order of magnitude as that of carbon, can hardly account for this effect. An addition of boron in the range of 0.001 to 0.003 pct is about as effective as an addition of 0.30 pct Mo, 0.40 pct Cr, or 1.25 pct Ni in increasing the hardenability of a 0.40 pct C steel;' however, increasing the carbon content of the steel decreases the effectiveness of the boron addition."' The difficulty in understanding why so small an addition of boron can replace much larger quantities of the more strategic alloys, together with the erratic behavior sometimes encountered in boron-treated steels, has interfered with their general acceptance by industry. In the belief that an understanding of the mechanism by which boron increases the hardenability of steel should lead to a more general acceptance of boron-treated steels, a research investigation to determine this mechanism was undertaken at Battelle Memorial Institute under sponsorship of Wright Air Development Center. Experimental Work In order to study the effect of boron on the transformation of austenite to ferrite and bainite, a group of steels was made with a basic composition similar to that of the SAE 8600 series. This base composition was chosen because it has sufficient hardenability to permit accurate measurement of the times required for transformation to start at various temperatures. The chemical analyses of the steels used in the first part of this investigation are listed in Table I. These steels were made as 200 lb heats in an induction furnace. The furnace charge was Armco ingot iron with the alloying elements added as ferroalloys. After the alloy additions were made, the heat was deoxidized with 0.125 pct Al. A 100 lb ingot was cast and an addition of 0.003 pct B, as ferroboron, was made to the metal remaining in the furnace. This metal was cast into a second 100 lb ingot. The ingots were forged to 11/4 in. diam bar stock from which end-quench hardenability specimens were obtained. Part of this material was further reduced by hot rolling to lx¼ in. bar stock from which specimens were obtained for isothermal transformation studies. Studies of Nucleation and Growth: End-quench hardenability tests were performed on these steels, using an austenitizing temperature of 1600°F. The hardenability curves, shown in Fig. 1, indicate that boron treatment resulted in considerable increase in hardenability of the steels. Any such change in hardenability must result from a change in the transformation rate of the austenite, and these rate changes can be established readily by isothermal transformation studies. Isothermal transformation studies were conducted on these steels as follows: specimens were austeni-tized at 1600°F for 15 min, transferred to a lead bath operating at a constant subcritical or intercritical temperature, held for various lengths of time, and water quenched. The specimens were sectioned for metallographic examination to determine the amount and the type of transformation products present. In order to determine the effect of boron on the formation rate of ferrite, isothermal transformation tests were made on the 0.20 pct C steel in both the boron-treated and boron-free condition at an intercritical temperature of 1375°F where ferrite is the only decomposition product of this low carbon austenite. The results of these tests are shown in Fig. 2, where the percentage of ferrite formed is plotted as a function of time at temperature. It is apparent that boron markedly decreased the transformation rate of austenite to ferrite at this temperature.

Jan 1, 1956

By D. J. McAdam, R. W. Mebs

THE technical cohesive strength of a metal means, not the interatomic forces, but the technically estimated resistance to fracture. An example of such resistance to fracture is the so-called "true" breaking stress of a tension-test specimen, the breaking load divided by the sectional area at fracture, According to the prevalent view,8 the technical cohesive strength of a metal, in any particular state as regards prior mechanical treatment and heat-treatment, is determined by a limiting value of the algebraically greatest principal stress.? In two previous papers by one of the authors,14,15 evidence was presented to indicate that the technical cohesive strength of a metal cannot be represented by a single stress value, but that it comprises an infinite number of values corresponding to the infinite number of possible combinations of the principal stresses. The technical cohesive strength thus comprises an infinite number of technical cohesion limits, each representing a specific stress combination at fracture. In the same papers, evidence was presented that plastic extension causes a continuous increase in the technical cohesive strength. Such a variation is not in accordance with the prevalent view that plastic extension first increases, then decreases, the technical cohesive strength.8 In this paper, as in the previous papers,14,15 the algebraically greatest principal stress will be designated S1, the least principal stress will be designated S3, and the intermediate principal stress will be designated S2. The technical cohesion limit under polarsymmetric tension (S1 = S2 = S3) will be termed the "disruptive stress," and the cohesion limit under unidirectional tension (S2 and S3 = o) will be termed the "severing stress." 14,15 The yield strength of a metal, according to the generally accepted theory, may be represented by a constant value of the shearing-strain energy, and hence by a constant value of the sum of the squares of the three principal stress differences. In the second of the previous papers,"' however, evidence was presented that the limiting yield stress decreases with increase in the volume stress, the algebraic average of the three principal stresses.* This influence of the volume stress becomes prominent only in the field of triaxial tension. In the two previous papers, 14,15 diagrams were presented to show the variation of the technical cohesion limit, yield stress, and ultimate stress with the combination of principal stresses and with plastic extension. Those diagrams and the resultant conclusions are derived from experimental data obtained by other investigators. They are based chiefly on results of tension tests

Jan 1, 1943

By W. H. Hough, P. B. Leavenworth

Development in the upper Texas Gulf Coast during 1944 resulted in the discovery of 19 new fields as compared with 11 during 1943. These discoveries include 10 oil fields, one dry gas field, and eight gas-condensate fields. Drilling During the year 590 wells were drilled as compared with 418 drilled during 1943. Of these operations, 485 wells were drilled in proven fields, with the following results: 281 oil wells, 22 condensate wells, one dry gas well and 141 dry holes. The remaining 105 wells were wildcats, of which 19 were producers. The geological distribution of these discoveries was as follows: In 1944, production amounted to 178,-522,630 bbl., which was an increase of some 31,670,384 bbl. over the 1943 figure of 136,852,246 bbl. These figures include both condensate and oil production, as separate figures are not available. Wildcatting in the area was more successful during 1944 than in 1943 as the following comparison of number of wells drilled illustrates: Discoveries during 1944 Smith Point, Chambers County.—Standard Oil Company of Texas completed its No. I State, sec. 109, on Feb. 15, 1944, in a Frio sand at 8135 to 8146 ft. The well flowed 250 bbl. of 42º gravity oil through an 1/8-in, choke. Gas-oil ratio was 800 to I; tubing pressure, 1100 bbl. Four other oil wells and one gas well were completed during the year. This discovery does not appear to be of major importance. The producing area lies on the upthrown side of a large fault. North Winnie, Chambers County.—Sun Oil Co. completed No. I P. E. Dougherty on Apr. 27, 1944, from the Frio, through perforations at 8757 to 8759 ft. The initial production was 154 bbl. of 38.3º gravity oil through an 1/8-in. choke. Gas-oil ratio Was 2526 to 1; tubillg Pressure, 2280 1b.; casing Pressure, 1225 lb.; total depth, 9519 ft. Three other wells were drilled during the Year. This discovery is on the downthrown side of the major Winnie Stowell fault, and increases in magnitude the already large producing area along this fault. Mayes Field, Chambers County.—Humble Oil and Refining Company's No. I Mary Etta Mayes was completed on Dec. 24, 1944, in a Frio sand, at 8166 to 8169 ft. through 1/4-in. for 768 bbl. of 40.3º gravity

Jan 1, 1945

By M. M. Fine

In a laboratory study of grinding and classification of silica sand, a satisfactory means of producing the medium-fine specification sand desired by producers of flint-glass containers was developed. The best procedure consisted of ball-mill grinding and double classification, which gave a properly sized sand containing less iron than the feed.

Jan 3, 1950

By Nicholas J. Grant, Italo S. Servi

SPECIAL polishing and etching techniques were developed during an investigation of the high temperature mechanical properties of high purity aluminum (99.995 pct Al).* Electrolytic polishing was done successfully in the following electrolyte: 5 ml perchloric acid (72 pct), and 95 ml glacial acetic acid. No special precautions need be taken during the preparation of the electrolyte since no appreciable heat of mixing is evolved. Although the electrolyte is not an explosive, it is recommended that Jacquet's safety rules' be followed during the polishing operation. A voltage of 25 to 60 v gives a good polish in about 2 min at room temperature after preparation on 3/0 metallographic paper. Most of the grain boundaries are visible under the microscope after polishing. Since the current is controlled essentially by the resistance of the bath, it is necessary to keep the anode-to-cathode distance as constant as possible. Accordingly, polishing of irregularly shaped pieces will be difficult. A cooling bath and a stirring system are advisable in order to keep the temperature of the bath uniform and constant. Coarse-grained samples can be macroetched in a few seconds by lowering the voltage below 10 v. This is done after electrolytic polishing, without removing the sample from the bath, Fig. 1. The specimen can be repolished in less than 1 min by raising the voltage above 25 v. The "galvanic etching" technique, which has been described elsewhere,' was found to be helpful not only for macroetching, but also for microetching coarse-grained specimens. In fact, the different orientations of adjacent grains provide good contrast at the grain boundaries, when the sample is observed under polarized light. If the specimen is only partially etched, Fig. 2a, the grain boundaries can be located without completely destroying the appearance of the surface of the specimen. The unetched surface appears black under polarized light. Excellent color contrast is obtained by using a "sensitive tint" plate in the optical system of the microscope. In this case, the unetched surface has a magenta color, while the etched part of the sample assumes different colors varying from green to brown, according to the orientation of the grains. Etch pits were produced on high purity aluminum by using the technique suggested by Lacombe and Beaujard." Good results also were obtained by substituting 70 pct nitric acid for the fuming nitric acid recommended. This gave an etching reagent of the following composition: 70 ml nitric acid (70 pct), 50 ml hydrochloric acid (37.5 pct), and 3 ml hydrofluoric acid (48 pct). An example of the results is shown in Fig- 2b. The outline of the etch pits is revealed sharply if the specimen is observed under polarized light, as shown in Fig. 2c. These metallographic techniques are not suitable for the examination of commercially pure (2s) aluminum. References 'P. A. Jacquet: Metal Finishing (Nov. 1949) 47, p. 62. 21. S. Servi: Metal Progress (1950) 58, p. 732. 3 P. Lacombe and L. Beaujard: Journal Inst. of Metals (1947) 74, p. 1._________________________

Jan 1, 1952

By S. B. Christy

The practice of the cyanide-process of gold-extraction has brought to light many important contradictions of familiar chemical analogies, which still obscure both the theory and the practice of the art with distinctions subtler and more difficult to make or follow than those which delighted the heart of the old-time metaphysician. Yet Nature herself has drawn these distinctions; and if we hope to succeed in this modern search for the Golden Fleece, we must be able to follow her through the winding labyrinth. There are so many phases of this question that I shall attempt to touch on only one of them at this time, but it is one that lies at the root of many others. In reviewing my paper on " The Solution and Precipitation of Cyanide of Gold,"* Mr. E. B. Wilson contends† that" in the solution of gold by means of alkaline cyanides the various reactions are determined, as to their order and intensity, by the relative position of the elements concerned in the electro-chemical series, or series of voltaic tension." In a modified form this statement is probably true. That is to say, the difference of electrical potential in any closed electrical circuit determines the nature of the reactions which ensue. But the matter is not so simple as Mr. Wilson assumes. Recent investigations show that the order of the metals in the electro-chemical series depends not only on the nature of the elements themselves, but also on the chemical composition of the solution in which they are placed; its degree of concentration; its temperature; and, in the case of gases, on the pressure. Unless all these conditions are taken into account, inferences drawn from the electro-chemical series are likely to prove more

Jan 1, 1901

By Henry R. Piehler

Continuous seven- and nine teen -filament close-packed silver-steel filamentary composites mere tested in tension. For purposes of comparison, the tensile behavior of the composite was predicted from the measured properties of the individual com-ponents. It was assumed that the axial strain is the same in both components and that the contribution of each component to the composite flow stress is proportional to its volume fraction. Good agreetnent was obtained between the observed and predicted tensile behavior. However, the composite elongation at fracture was about twice that observed when the individual steel wires were tested alone. Composites in which the filaments were widely spaced failed by the consecutive fracture of the filaments. In composites with closely spaced filaments, a composite instability preceded frachcre. These effects are explained in terms of a lateral restraint to the necking of the filaments which develops in the deforming composite. TWO-COMPONENT or composite materials are increasingly being developed and used as structural materials. Of all the composite geometries used, the filamentary configuration has proved to be the most successful. Polymer-bonded fiber-glas, the most common of the filamentary composites, has been investigated most extensively to date. One explanation of the behavior of fiberglas1 suggests that the load transfer between the glass fibers and the polymer matrix occurs primarily through friction. Bond separation between the fibers and the matrix is presumed to occur at very low stresses. Subsequently, only frictional bonding can provide for the transfer of load from the matrix to the fibers. The force normal to the fiber-matrix interface which gives rise to this friction is assumed to arise from the matrix shrinkage which occurs during solidification. The behavior of metallic filamentary-composite materials would be expected to differ from that of fiberglas in several significant aspects. Residual stresses resulting from differences in thermal contraction can be kept to a minimum by proper heat treatment. A strong wetted bond is formed between the two phases. In brazed joints,2 for example, the interphase bond is sufficiently strong that the weaker material will fail before separation occurs at the interface. Most metal filaments can undergo appreciable amounts of plastic deformation before failure. Failure by plastic instability or necking frequently occurs in metallic filaments, but not in glass fibers tested at room temperature. Differences between the behavior of fiberglas-polymer and metallic filamentary composites have indeed been observed in composites containing various types of metallic filaments in a silver matrix.3,4 At strains of the order of 10-2 pct, all the deformation was accommodated by the silver matrix. Hence, the strength of the composite depended only on the fiber concentration and not on the nature of the fiber. At higher strains, the strength of the composite increased when filaments with higher work-hardening rates were used. Surface slip line observations on a silver-mild steel composite that had been stretched 4 pct showed that an appreciable amount of deformation occurred in the filaments. Work on tungsten-copper filamentary composites5 has shown that the ultimate tensile strength for varying filament fractions followed a linear mixture rule. Assuming that the axial strains in both filaments and the matrix are equal, this linear mixture rule can be expressed as: The subscripts c, f, and m refer to the composite, filaments, and matrix, respectively. A and V are the area and volume fractions of each component. sc and of are the ultimate tensile strengths of the composite and the filaments. sm is the flow stress of matrix at a strain equal to the elongation at failure of the filaments. However, the tungsten filaments can undergo only a limited elongation before they fracture without an appreciable reduction in area. A composite containing more ductile filaments might indeed deviate from this linear mixture rule for the ultimate tensile strength, since filament failure by necking might be arrested by the matrix. SPECIMEN PREPARATION Specimens were prepared from 0.8 pct carbon steel piano wires of 0.015 in. initial diameter. The wires were given a thin nickel flash and a silver plate varying in thickness from 0.015 to 0.007 in., depending on the filament fraction desired. In order

Jan 1, 1965

By Richard Pearce

H. M. Howe, Boston, Mass. (Communication to the Secretary): One by one our venerated idols are shattered, our cherished beliefs are filched away. Mr. Pearce's interesting experiments on the effect of an intermixture of coal in expelling arsenic from roasting copper-ores seems at the first blush to spike one of the great cannons of our faith. Plattner, however, is so positive that coal does lead to the expulsion of arsenic that we may well pause before accepting Mr. Pearce's results as final, and ask whether there is not some explanation of the discrepancy between them and Plattner's statements. Plattner states that while ferric arseniate decomposes easily under the action of carbonaceous matter with expulsion of arsenic as arsenious oxide (As2O3) and sub-oxide of arsenic (it is now generally thought, I believe, that this supposed sub-oxide is really but a mixture of metallic arsenic and arsenious oxide); cupric arseniate, on the other hand, undergoes this decomposition with difficulty, usually forming a certain proportion of arsenide of copper. Now, may not the whole matter lie just here? Mr. Pearce experimented on an ore containing its arsenic as enargite, sulph-arsenide of copper. This, in roasting, would probably give rise to arseniate

Jan 1, 1890

New Products Equipment

Jan 10, 1950

Jan 1, 1967

By Alden B. Grenninger

The time-honored description of the growth of metal crystals to form polycrystalline aggregates is one in which two important steps are considered: (1) nucleation, and (2) dendritic growth, each dendrite starting from its individual nucleus and resulting (upon slow cooling, assuming no solid phase changes) in a macrograin. This picture of the process of crystallization is incomplete, and it is with the hope of enlarging upon it that the following summary and correlation of experimental results are given. Mosaic Structure For an exact definition of the mosaic structure of metal crystals—if, indeed, one can be found that will hold for all metals—one must await the results of much experimental work in this field. The writer's investigations have been confined almost entirely to copper and a few of its alloys. The following terms are proposed, and will be used in this report: Macromosaic Structure1.—Large-scale mosaic structure; more specifically, mosaic structure of a scale large enough to produce splitting of Laue spots on back-reflection Laue X-ray patterns2. The deviation from exact parallelism of neighboring macromosaics varies from a few minutes to a few degrees3. Just as there are no exact dimension limits for macrograins, so the dimensions of a macromosaic vary considerably. Macromosaic structure may often be seen on copper single crystals if they are examined carefully with critical illumination4. However, back-

Jan 1, 1936

Jan 1, 1959

The 128th meeting of the American Institute of Mining and Metallurgical Engineers constituted a two weeks trip through the Great Northland of Ontario and Quebec and was a most memorable occasion. The last visit of the Institute to Canada was made in 1907 when the mines, which now have brought world wide fame to some of the camps, were not yet dis-covered. The party reached its greatest numbers at Porcupine where 167 visitors and nearly one hundred local members participated. Five members of the party from the States were on the previous trip in 1907. They were Mr. and Mrs. L. D. Huntoon, John Stevenson and son and E. F. Eurich. The Minister of Mines for the Province of Ontario attached his private car to the "Mining Engineers' Special" and made the complete trip through Ontario. This was a happy incident in many ways and gave the visitors an opportunity to discover a spirit of mutual accord between the Minister and mining industry that might well be emulated elsewhere. Two compartment cars and one standard Pullman with the Institute members from New York and the metropolitan district were attached special to the 6.15 p.m. Lehigh Valley train from New York, Sunday, Aug. 19, en route to Toronto, where was held the first session of the Institute's 128th Meeting.

Jan 9, 1923

By R. I. Jaffee, H. P. Nielsen

In recent years much attention has been given to high melting alloy systems. It has been of interest in this respect to investigate the alloys of platinum and tungsten, which were known from the literature to have very high melting points up to about 50 pct tungsten, but about which little had been published on the high-tungsten side of the system. Powder metallurgical methods were used throughout this investigation for the preparation of the alloys, utilizing electrical sintering techniques such as are used for tungsten and molybdenum. In the course of the work it was found desirable to determine fusion temperatures of the alloys, and it was possible from these and other data to draw a tentative constitutional diagram (solidus, mostly) applicable to the high-temperature part of the system. No attempt was made to determine solid solubility vs. temperature data, nor to investigate the lower temperature transformations in the solid state. Data on the microstructure, hardness, and a note on oxidation resistance of the sintered alloys were obtained. Past Work Miillerl determined liquidus temperatures of platinum-rich alloys to 50 pct tungsten, using a radiation method employing a photoelectric cell, and found that the melting points increased progressively from I771 C for platinum to 2350°C for the 50 pct alloy. Microscopic evidence by Miiller that complete solid solutions exist to 50 pct tungsten was not checked by Kremer2 who, according to Vines and Wise,3 found that "although the 8 pct tungsten alloy was a solid solution, the 26 pct tungsten alloy contained a eutectic or an intermediate phase." Hultgren and Jaffee4 using X ray methods found continuous solid solutions to at least 33.6 pct tungsten (35 at. pct) after annealing in vacuum for 6 days at I000 C. Vines and WiseS report work communicated to them by E. C. Rhodes on wrought alloys to 7 pct tungsten, which showed that tungsten hardened platinum extremely rapidly, and was one of the most potent hardeners of the binary additions to platinum. Considerable quantities of 4 pct tungsten platinum wire have been produced for grids in radar tubes and for aircraft spark plugs. Some of the alloy for the latter application is made by sintering, the remainder by smelting and casting. Materials The platinum powder used in this work was kindly supplied by the Research and Development Laboratory of the Owens-Corning Fiberglas Corp., Newark, Ohio. It was prepared from scrap platinum. After dissolving in aqua regia and evaporating almost to dryness, the solution was worked up several times with concentrated HC1. The resultant platinic chloride was diluted considerably, and metallic zinc was added, which precipitated the platinum in a very finely divided form. After dissolving the

Jan 1, 1949

By D. L. Wood

INTERNAL oxidation' is a process in which oxy-gen, diffused into a suitable alloy, causes precipitation of solute oxide particles as the oxidation front moves inward. During an investigation of internal oxidation now in progress it was observed that the grain size is relatively small in thin strip specimens that have been internally oxidized in the as-rolled condition. This may be due to the restraint of grain growth by the precipitated oxide particles. It was observed also that the grain size in unoxi-dized portions of partially oxidized specimens was

Jan 1, 1958