Search Documents

By Robert H. Holgers

Eveleth Taconite Co. was chartered on July 29, 1963, and is 85% owned by Ford Motor Co. and 15% by Oglebay Norton Co. The latter also serves as managing agent. The location of the company's facilities is depicted in Fig. 1. The Thunderbird mine is located midway between the cities of Eveleth and Virginia, Minn. (Fig. 2). The Fairlane plant and General Office are located approximately 10 miles south on the St. Louis River near the community of Forbes (Figs. 3 and 4). The crude ore and the finished pellets are transported by a common carrier railroad, the Duluth, Missabe & Iron Range Railway Co. The facilities are also serviced by the Duluth, Winnipeg & Pacific Railway Co. Pellets are hauled year around by the DM&IR to its docks 60 miles south in Duluth, Minn. Ford Motor Co. consumes its share of the high grade pellets at its Rouge plant in Dearborn, Mich., and Oglebay Norton Co. sells its share in the open market. HISTORY Following six months of preliminary engineering by the initial staff of Eveleth Taconite Co. and the Western Knapp Engineering Div. of Arthur G. McKee & Co., the project was approved by Eveleth's board of directors on Apr. 17, 1964. On May 1, 1964, contracts were awarded to McKee for the mine, coarse and fine crushing and concentrating facilities, and to Allis-Chalmer for the pelletizing facilities. The pre-production surface overburden stripping contract was awarded to Skubic Brothers Co., Virginia, Minn. Ground-breaking ceremonies were held at the Thunderbird mine on

Jan 1, 1969

T. R. HARRISON, Washington, D. C. (written discussion). *-Mr. Kowalke shows that a high resistance millivoltmeter is subject to smaller errors, due to change in resistance of the thermocouple to which it is attached, than is a low-resistance instrument. He uses as examples instruments having resistances of 30 and 2 ohms, respectively. At the Bureau of Standards, resistances above 300 ohms would be considered high and 30 ohms rather low. In the tests on calorized-iron thermocouples, a difference between the first and third calibrations of the couples serves to show changes due to the intermediate heat treatment and only under certain conditions would changes in calibrations due to changes in the wire be detected by ,a recalibration after 1 1/2 in. had been cut from the hot-junction end of the couple and the ends rewelded. The calibration of a couple depends only on the thermoelectric prop-erties of that part of the couple which lies within the region of non-uniform temperature, i.e., the temperature gradient; hence, so long as the temperature gradient falls along wires of similar thermoelectric properties no change in the electromotive force is produced by altering the metals of those parts of the circuit that are at uniform temperature. Usually at the cold-junction end of the circuit, copper leads, brass binding posts, manganin resistance coils, and various other materials form part of the circuit, but so long as all are at a uniform temperature (or if for each junction between unlike metals there is a similar opposing junction at the same temperature) no resultant thermoelectromotive force will be produced thereby. Likewise, if a length of several inches at the hot-junction end of the couple is at uniform temperature, it matters not if this section is unlike other parts of the couple, so long as there is good metallic connection and no source of e.m.f. other than thermoelectric is present. Cutting off part of the hot end of the couple within such a region of uni-form temperature would not alter the e.m.f. of the couple.

Jan 12, 1919

Jan 1, 1934

By L. H. DeWald

During the examination of various commercial brands of copper wire bars, which had exhibited different degrees of adaptability for being drawn into fine gages of wire by the present-day high speed machine, it was found that each brand had a more or less characteristic crystal macrostructure. The extremes of these macrostructures are similar FIG. 1.-EFFECT OF METAL TEMPERATURE IN CASTING ON CRYSTAL MACROSTRUCTURE OF BAR. Reading from left to right, metal temperatures were 1166" C., 1149" C., 1132" C.. 1121" C., 1093" C. to the maximum variation shown in the photomacrographs reproduced in Fig. 1. As the various brands did not differ materially in chemical composition, it was concluded that the differences in structure were the result of variations in casting technique.

Jan 1, 1931

By Chester S. Conrad

SEVERAL years ago Pittsburgh Consolidation Coal Co. intensified efforts to combat the hazard of mine fires. The program consisted of three parts in the order of likely accomplishment: 1) Purchase and installation of newer and more practical fire fighting equipment. 2) Establishment of trained fire fighting teams at every mine plant. 3) A drive to remove the causes of mine fires. Experimentation with alternating current on section equipment is a major development in this part of the program. Use of alternating current to power mining equipment had been recognized as being most practical from the standpoint of safety. A means to re- place the d-c traction motor is all that has delayed complete section mechanization with a-c power.

Jan 1, 1958

By Roger H. McConnel

Throughout the world in 1950 there has been extensive exploration for metals, with emphasis on iron, copper, gold, lead, and zinc. Among the features most apparent in reviewing exploration and development are the staggering sums required, the over-riding influence of government policies throughout the world, and the need for intensified search.

Jan 2, 1951

Jan 1, 1904

By R. B. Moore

Page History................................ 708 What is Radioactivity?........................ 710 Disintegration Series.......................... 711 Radium Ore Deposits......................... 713 Metallurgical Treatment........................ 717 Methods of Ore Concentration..................... 722 Future Supply of Ore......................... 723 Uses of Radium............................ 723 Mesothorium as a Substitute for Radium................. 724 Discussion.............................. 725 Probably no other metal excites as much interest, among both scientific men and the general public, as radium. This is due partly to the high cost of radium salts and partly to the peculiar properties of the element. Since radium-bearing ores were discovered in the United States, the interest of American scientific men has been stimulated and, at the present time, more radium is extracted and refined in this country than in all the rest of the world together. HISTORY The property of radioactivity was discovered, partly by accident, by Henri Becquerel, the French physicist, in 1896. He was experimenting with certain fluorescent substances in order to find, if possible, a connection between fluorescence and the recently discovered X-rays. Among other chemicals which possess the property of fluorescence, he was using salts of uranium. His custom was to expose the fluorescent substance to the action of sunlight and then register the effect of possible penetrating radiation on a photographic plate protected from ordinary light. Bec-querel's experiments gave positive results at once, and he at first believed that he had discovered a relation between fluorescence and X-rays. Later he exposed a plate to a uranium salt which had not been previously exposed to sunlight. To his surprise, on developing this plate, he found that he had obtained the same effect as he had previously secured when

Jan 1, 1919

By R. L. Templin, D. A. Paul

The modulus of elasticity is defined as the ratio of stress within the proportional limit to corresponding strain. This property, as thus defined, is a constant for each kind of material; and in tension or compression is usually designated by the symbol E. The modulus of elasticity serves as an index of the stiffness of a material or a measure of its ability to resist change of shape under stresses not higher than the proportional limit. In view of the frequency with which the modulus of elasticity is used in engineering calculations, it is surprising to note the uncertainty that exists as to authentic values, and the marked lack of published information relating to the variation of the constant E within individual alloy systems. A value of 10,000,000 Ib. per sq. in. has been quoted as representative of aluminum and its alloys. This value has been found to be approximately corrcct for pure aluminum and aluminum alloys in which the total percentage of the alloying elements is low, but seriously in error in the case of alloys that contain relatively large amounts of the alloying elements. a National Metals Handbook. b Intcrnatiunal Critical Tables. '' Aluminum Co. of America. " Based on density of alurminum (2.70). c Smithsonian Pliysical Tables.

Jan 1, 1931

By Robert R. French

Beneficiation of low-grade nonmetalliferous mineral deposits by electronic color sorting is currently undergoing a period of rapid development. For those deposits in which the specific gravity, strength, soundness, and electric and magnetic properties of the ore and gangue are similar, the possibility of separation by color, reflectivity, or fluorescence offers hope for the utilization of much poorer quality ore than previously thought possible. For those ores in which consistency of color is required or for which a dry process is preferred, the electronic color sorter is particularly adaptable. Tests performed late in 1966 and reported herein are the result of continued interest in the dry beneficiation of gypsum and the development of higher capacity color-sorting machines. These tests should be considered only as an indication of the efficiency of the process and only with respect to the low-grade, untreated ore tested. Although most of the ore mined in Martin County, Ind., is of acceptable quality, a few thin carbonate strata and irregular nodules of dolomite and limestone are present within the main evaporite bed (Fig. 1).

Jan 1, 1969

By Francis N. Flynn

Many excellent papers, descriptive of the milling and smelting of every kind of commercial ores, the refining of virgin metals, the casting into various shapes demanded by the trade, the rolling into shapes best suited to the factory machinery and the making of composition alloys to suit every requirement have been issued by the many technical societies dealing with non-ferrous metals. It is a wonderful collection of papers, of which the mining and metallurgical engineers may well be proud, but strange as it may seem, metallurgists in general appear to take the stand that when they have delivered suitable alloys to the foundry and rolled products to the factory their duty to write papers has ceased, at least in so far as the A. I. M. E. is concerned. Still we read in the daily papers that the mining companies are absorbing metal-manufacturing industries. The purpose of this paper is to describe the reclaiming of non-ferrous scrap metals at manufacturing plants, taking as an example the automobile industry. Collection and Disposition of Scrap Until about five years ago, much of the factory scrap, with little or no preliminary treatment, was sold to secondary-metal smelters. Of late years the factory salvage department has become an important part, of the plant in reclaiming everything of value and incidentally does much of the work formerly done by the smelters. Like most good things, it is sometimes overdone, and much work is done at the factory with inexperienced men that could be done much better by experienced skilled labor at the custom smelting plants. Employees of the salvage department collect the waste products in all departments at the source and in that way avoid much contamination. Every reasonable precaution is taken to keep the scrap clean. It is hand-sorted, cut, burned, magnetized, concentrated, separated or compressed, as the case may be, preparatory for re-use in the plant or for selling to others.

Jan 1, 1930

By W. G. Scott

SINCE devising the incline top-slicing method in use It the Coronado mine,1 I have had numerous inquiries is to how the same system could be adapted to larger orebodies. Based upon our experience here, 1 have outlined below some suggestions for its, application to orebodies of larger size. Modifications and extensions, of course, would have to be made to take care of different dimensions and irregularities. In order that one may have a better understanding of the scheme, a brief description of the Coronado method will he given first.

Jan 11, 1917

By D. H. Bacon

Our Transactions contain so many suggestions of apparently trivial, yet really important, contrivances for the saving of time and

Jan 1, 1893

By T. R. Lippard

PURE gypsum may be broken down into its constituents as follows: [ ] Standard specifications (ASTM Designation C22-25) state that a material shall not be considered gypsum if it contains less than 64.5 pct by weight of CaS042H2O. Anhydrite, the second calcium sulphate mineral found in nature, may be broken into its constituents as follows: [ ] PROPERTIES OF GYPSUM AND ANHYDRITE Pure gypsum is colorless to white but various impurities change its color to shades of gray, brown, red, or pink. It has a hardness of 2 in the Mohs scale and can be scratched with the fingernail. The specific gravity of pure gypsum is 2.3 to 2.4, so that rock gypsum, free from moisture, weighs about 145 lb per cu ft. Gypsum crystallizes in the monoclinic system in tabular crystals that exhibit good cleavage

Jan 1, 1949

By R. C. Hassinger, D. V. von Rosenberg

Transverse dispersion has received considerably less treatment in the literature than has longitudinal dispersion. Different methods for determining transverse dispersion coefficients have been used in different investigations, and the results obtained have not been consistent enough to permit accurate generalizations as to the effect of various physical parameters on the magnitude of these coefficients. A numerical solution to the differential equation describing transverse dispersion in the absence of longitudinal dispersion was obtained to enable one to calculate the dispersion coefficient from experimental results. The more general dispersion equation including longitudinal dispersion also was solved numerically to give quantitative limits of a dimensionless group within which the assumption of negligible longitudinal dispersion is justified. Possible experimental procedures were examined, and one utilizing a cylindrical packed column was chosen for the determination of transverse dispersion coefficients. Values of these coefficients were determined for a system of two miscible organic fluids of equal density and viscosity, for two sizes of packing material over a wide range of flow rates in the laminar regime. The dispersion coefficient was found to decrease, for a constant value of the product of packing size and interstitial velocity, as the size of the packing material particles increased. INTRODUCTION Longitudinal dispersion has received extensive treatment in the literature, and consequently is better understood than its orthogonal counterpart, transverse dispersion. Many mathematical models of dispersion processes assume that transverse dispersion is rapid enough to damp out any radial** concentration gradients and therefore may be neglected. Laboratory and production results, however, indicate that this is a poor assumption.l,2 Various experimental procedures for determining transverse dispersion coefficients have been used in previous investigations, but the results have generally been expressed by similar correlations. The transverse dispersion coefficients obtained, however, have often varied considerably for given values of the correlation parameters. We feel that further experimental determinations of transverse dispersion coefficients will help alleviate some of the inconsistencies in these empirical correlations. One assumption implicit in all previous investigations is that of negligible longitudinal dispersion in the experimental system. An attempt to justify this assumption often is made using intuitive reasoning, but it is apparent that this reasoning must break down as the condition of zero flow rate is approached. A mathematical examination of the equations describing the system yields physical limits outside of which the assumption of negligible longitudinal dispersion is invalid. BACKGROUND In a porous medium, the "effective molecular diffusivity" De is less than the molecular diffusivity D measured in the absence of a porous medium, due to the tortuous path which a diffusing molecule must travel. Various authors3-5 have reported values of the ratio De/D in the range of 0.6 to 0.7. When there is fluid flow within the porous medium, mass transfer occurs by convective dispersion as well as by molecular diffusion. These are separate phenomena and can be treated as such on a microscopic scale. However, the mathematical complexity is such that only extremely simple geometries could be considered, and the results hardly would be applicable to the complex geometries existent in actual porous media. A more

Jan 1, 1969

By Forest Mintz

Many oil and gas producers find it advantageous to borrow against the value of their hydrocarbon re- serves. This paper considers the requirements for a reserve based loan and the calculations that a bank would perform to arrive at a loan amount. Three of the most common loan structures, i.e. a term loan, a production payment, and a revolving credit/term loan will be discussed. A typical outline for each type of loan is presented. Finally, a comparison of major considerations in the three financing techniques is shown.

Jan 1, 1982

By Ming-Kao Yen, W. R. Hibbard

Various rationalizations of preferred orientations in cold worked polycrystalline metals have been based on the operation of at least two three2 five, an indefinite number, and all,6 slip systems of the type occurring in single crystals. Pickus and Mathewson3 suggested that the cold rolling texture in face-centered cubic metals could be rationalized on the basis of two or more operating slip directions symmetrically disposed about the direction of flow in such a manner that the resolved shear stress factor is equal for all operating slip systems and lattice rotations cancel each other. The importance of the direction of flow, the necessity for the operation of slip systems capable of producing the required changes in external dimensions, the maintenance of a common surface between adjacent grains and a symmetrical arrangement of the operating slip systems in order to produce an end orientation which is stable under additional deformation lead to the following rationalization of textures based on the type of slip systems operative in single crystals. The rationalization is intended to explain why certain orientations are suitable for deformational flow without a change in orientation and thus are stable end orientations or ideal texture orientations. It does not attempt to explain how the grains of a randomly oriented polycrystalline aggregate will reach this orientation. The rationalization is based on the following four postulates: 1. The ideal textures for polycrystalline aggregates are the result of reorientations of individual crystals toward the same stable end orientation at which no further reorientation will occur even during additional deformation. Since, in simple slip, the relative orientations of the stress axis and the active slip system determine the change in orientation during slip, it is considered that the orientation of the stress axis with respect to the ideal texture determines what slip systems must be active to retain the stable end orientation. Therefore the stable end orientation should be a symmetrical one around the stress axis with respect to the active slip systems such that lattice rotations resulting from slip will cancel each other and prevent a resultant change in orientation. (Rotational symmetry only—not translation, inversion, nor others—is considered here.) Thus a metal under a pure stress should develop a texture consisting of one or more of the crystallographically symmetrical directions, <100>, <110> or <111> for cubic metals or <0001>, <1010> or <1120> for hexagonal close-packed metals, parallel to the stress axis. 2. Since the active slip direction is the direction of glide during simple slip and thus the direction of maximum shear movement, in the ideal texture the active slip

Jan 1, 1949

By Fortunato Pereira Gamba

The Department of Narino (formerly included in the Department of Cauca) is a narrow band about 170 km. (100 miles) wide in the southern part of the Republic of Colombia, near the boundary of Ecuador, as showu in the sketch-map, Fig. 1. Its capital is Pasto, a small city of 25,000 inhabitants; the pri~icipal towns are T?querres, Cumbal, Ypiales, Barbacoas, and Tumaco. The port on the Pacific ocean is Tumaco, and traffic in the interior is carried partly on the Patia river (steam navigation to the fluvial port of Barbacoas), and afterwards overland over poor roads by human bearers or on mule-back.

Jan 1, 1913

By Lowell B. Page

The White River Shale Project has completed a 5,000-foot production decline and a 30-foot diameter 1,010-foot deep shaft into its oil shale orebody in the Uinta Basin of eastern Utah. This is the first major underground access into these Green River deposits in this basin and provides an opportunity to establish and monitor in-situ rock mechanics stations as input to the mine engineering and planning of this large opening, high-tonnage mine. This paper discusses the history, mine development, and rock mechanics planning for this project.

Jan 1, 1984

By H. B. Smith, B. Egererg

In a previous paper1 the authors dealt with the physical properties of cold-rolled and heat-treated Britannia metal of the approximate composition Sn, 91 per cent., Sb, 7 per cent. and Cu, 2 per cent. It was found that cold rolling to more than 50 per cent. reduction produced a continuous softening of the metal when measured by the Brinell machine, whereas the Shore instrument indicated increased hardness; that the strength of the material followed the Brinell hardness and that the metal therefore became weaker the more it was cold-rolled; and further, it was found that hardness and strength could be largely restored to the cold-rolled metal by "baking" for about one hour at any temperature between 200" and 450" F., the melting point. The higher the baking temperature, the more effective was the heat treatment as far as increased hardness was concerned. It seemed to be of little importance whether the metal was soaked or not at the baking temperature for a great length of time and the rate of cooling seemed to be immaterial. The present paper deals with the same alloy and more particularly with the resistance towards various forms of stress — tensile, bend and deep drawing. The metallography of Britannia metal has in part also been covered and an explanation attempted for the abnormal behavior of this alloy. Tensile and Bend Tests Two ingots 73/4 in. wide, 11 in. long and ¾ in. thick were cast from the same pot. One ingot was cold-rolled in one direction to a strip 0.241 in. thick, which furnished the tensile test specimens; the other ingot was rolled in the same way to 0.253 in. and furnished the specimens for the bend tests. The ingots were cast as described in the previous paper and cold-rolled in six passes.

Jan 1, 1930