Search Documents

By George T. Bator

If confronted with the problem of pumping a mixture of slime-free sand, gravel and boulders up to six in. in diameter, at the rate of 175 tons per hr in one single-stage pump against a static head of 90 ft and a total head of 140 ft, of which 20 is on the suction side, an engineer might be forgiven for backing away from the job, especially if he were also told that the pump wearing parts must have a minimum hardness of 550 Brine11 for the sake of abrasion resistance. Yet precisely that feat has been accomplished in the gravel pit of John B. LaGarde, Inc., near Anniston, Ala. The pump used is of decidedly novel design and its successful operation since installation 1.5 years ago suggests that it may be of timely interest in numerous other applications in the mining industry, such as pump transportation of coal washer refuse or rock from open-pit's without unduly fine crushing.

Jan 9, 1950

By Olin G. Bell

At the beginning of the year 1935 the older fields in Southwest Texas, and particularly those discovered during 1934, had been practically delimited and only normal development continued. As a result, operations in this area were somewhat slowed down. Shortly after the first of the year, however, activity in the area was greatly accelerated, due largely to the fact that the Loma Novio field, discovered during the last few days of 1934, indicated the presence of a new productive trend east of and parallel to the Government Wells field and also indicated the presence of a new productive horizon, the Loma Novio sand, approximately 100 ft. lower than the Government Wells sand zone. Other discoveries during the year greatly augmented the activity in the district. During the year there were 651 oil wells, 53 gas wells and 275 dry holes drilled in this area during the year. Most of the operations were in the Government Wells, Cole, Loma Novio, Seven Sisters and Lopez fields. New Fields Four new fields were discovered during 1935 as follows: Seven Sisters and Piedra de Lumbre in Duval County; Loma Alto in McMullen County; and Lopez in Webb County. Seven Sisters Field.—The Seven Sisters field, opened in May, was the direct result of a systematic search for new productive areas northeast of the Loma Novio field. The first producer, Harvey & Henderson NO. 1 Chernosky, survey 226, was completed in the Labbe (Chernosky) sand at 2220 ft. However, the second producer, Santa Clara Oil Co. No. 1 Welder in survey 385, drilled about one mile south of the discovery well, failed to find production in the Labbé sand and was carried on down and completed in the Government Wells sand at 2473 ft. with an initial production of 20 bbl. of oil per hour. These two discoveries, in the Labbé and Government Wells sand, started an active leasing and drilling campaign in this part of Duval County and drilling operations continued especially active throughout the remainder of the year.

Jan 1, 1936

NEW MEMBERS The following list comprises the names of those persons who became members during the period Nov. 9, 1918, to Dec. 10, 1918. ALBERT, EDWARD J 235 E. Upsal St., Philadelphia, Pa. BARRY, D. A Supt. of. Mines, The Big Five Min. Co., Idaho Springs, Colo. BATON, GEORGE S., Cons. Min. Engr., Baton & Elliott, 2412 First National Bank Bldg., Pittsburgh, Pa. BAXTER, HAROLD ALEXANDER, Met. Engr. & Operation Supt., Tacony Ordnance Corpn., Philadelphia, Pa. BENNETT, JOHN S., Chem. and Min. Engr Copiap6, Chile, South America. BOWDEN, MALCOLM, Min. Engr.; Efficiency Engr., Elm Orlu Min. Co., Butte, Mont. BROWN, HAROLD C 2d Lieut., A. S. A. P. BROWN, THOMAS ALBERT, Min. and Met. Engr.; Supt., The Royal Tiger Mines Co., Breckenridge, Summit Co., Colo. BROWN, WALTER S., Investigator, New Jersey Zinc Co. (of Pa.), Palmerton, Pa. BURDETTE, R.. S Capt., Ord. Dept., U. S. A. CALLANDER, IRA C., Asst. Supt., Gauley Mountain Coal Co., Jodie P. 0., Fayette Co., W. Va. COLLINS, J. W., Foundryman, The Aluminum Casting's Co., "L" Plant, Cleveland, Ohio,

Jan 1, 1919

By C. L. Dake

Chemistry of Iron Solution IRON is much more soluble in the ferrous than in the ferric form. Where, as in the case of the ferrous silicates and the sulphides, the iron is already in the ferrous form, it may go at once into solution and be removed, upon the breaking down of the parent rock. If in the ferric form, it must first be reduced; usually by the decay of organic matter, the demand of the decaying carbonaceous matter for oxygen being so great that the latter is abstracted from the ferric compounds and the iron is thereby reduced and rendered' soluble. The iron may go into solution as the sulphate, or in the presence of excess CO2 as ferrous carbonate. It is probably soluble as salts of the organic acids.1 Recent work indicates that these are important in the formation of bog ores.2 There is considerable variety of opinion concerning the behavior of these organic compounds.3 The secretions about the roots of plants and trees also cause the solution and removal of iron and a consequent bleaching of the soil.4 While the matter is not yet well understood, we can probably say definitely that the so-called organic acids are a group of colloids which possess slightly acid properties, and the salts of which are partly soluble

Jan 7, 1915

Executive FREDERICK M. BECKET, Chairman HOWARD N. EAVENSON J. V. W. REYNDERS H. A. GUESS WILLIAM WRAITH Finance HENRY KRUMB, Chairman PAUL H. MERCER H. G. MOULTON Admissions JOHN M. LOVEJOY, Chairman GEORGE D. BARRON DONALD M. LIDDELI. E. V. DAVELER W. D. B. MOTTER, JR. Alternates AMOR F. KEENE L. F. STROBEL SAM TOUR Membership LEWIS B. LINDEMUTH, Chairman EDWARD H. ROBIE, Secretary Executive Committee NELSON DICKERMAN FREDERICK LAIST FRED H. KAY THOMAS T. READ H. A. KURSELL A. T. SHURICK SAM TOUR

Jan 1, 1932

IT will be recalled that the first professor of metallurgy in the United States, appointed in 1855, never really gave any instruction in metallurgy and gradually turned into a professor of mineralogy. Metallurgy was included with mining in the early curricula, two students who took the B.S. in mining engineering from the Polytechnic College of Pennsylvania in 1863 wrote their graduation theses on the metallurgy of copper and zinc, respectively. Even after Columbia School of Mines established, in 1868, a separate curriculum leading to the Ph.B. degree in metallurgy, very few students elected it,* preferring to take the mining degree, since they received in its curriculum nearly all the metallurgical instruction they would have in the metallurgical curriculum. For many years a large proportion of the men who attained prominence in metallurgical enterprises had taken mining rather than metallurgical degrees. METALLURGY Clifton Sorby's study of thin sections of rocks under the micro- scope, beginning in 1850, and its subsequent development by Zirkel and others, had made microscopic petrography a recognized department of, geological research as early as 1873. It was inevitable that the idea of studying polished metal surfaces under the microscope by reflected instead of transmitted light would occur to investigators. Sorby himself did it in 1864, and Adolph Martens and Floris Osmond may be especially named ', among the many European workers who, by the late eighties, had so developed the necessary techniques that they were able to photograph polished metal surfaces at magnifications as high

Jan 1, 1941

By H. C. Howarth

THIS paper gives observations on ground movement and subsidence resulting from pillar drawing in the Lick Run section of Montour No. 10 mine of the Pittsburgh Coal Co. adjacent to solid coal owned by the U. S. Bureau of Mines at its Experimental mine in Snowden Township, Allegheny County, Pennsylvania. The investigation was planned by George S. Rice, chief mining engineer of the Bureau, who arranged the necessary cooperation with Dr. L. E. Young, vice president of the Pittsburgh Coal Co. Engineers of that company placed permanent monuments on the surface to establish the boundaries of the coal owned by the Bureau and to furnish fixed points to which all levels were referred. Engineers of the Experimental mine staff then covered the ground under observation with a checkerwork of monuments made of oak pegs set into the ground at 50-ft. intervals in two directions at right angles to each other. The level of these pegs was determined first from Dec. 16 to 30, 1929; again from May 25 to June 5, 1930, and finally from July 7 to 15, 1931. Observations were then discontinued because work had been stopped temporarily in this part on Montour 10 mine.

Jan 1, 1933

W. M. CORSE, Mansfield, .Ohio.-We have sometimes seen in indi-vidual tests ultimate tensile strengths ass high as 55,000 lb. per. sq. in. being attained under electric furnace practice. These results, of course, average much lower than that, but with better methods of melting, can we hope to get the strength up to somewhere near the figure attained by these individual tests? C. P. KARR.--Yes, because with the electric furnace you can lessen the oxidation by means of the impurities always found in the melting. But one of the most important things in making 88-10-2 bronze of this class is to use a core-sand mold with a very open grain, so that the

Jan 12, 1919

By A. B. Calhoun

These mines, which belong to the Burma Corporation, Ltd., formerly a London company now incorporated in Rangoon, Burma, are situated in the semi-independent state of Tawng-Peng, one of the small divisions comprising the northern Shan states and erroneously known as part of Upper Burma. Bawdwin is approximately 23' 6' N. latitude and 97" 20' E. longitude, 450 miles north of Rangoon, 169 miles northcast of Mandalay and 50 miles south and west of the Province of Yunnan, China (see Fig. 1). Although the mines were worked by the Chinese during the Ming Dynasty, 1412 A. D., the most extensive operations took place between 1796 and 1851, when the mines contributed largely to the silver market of China. During the reign of Tung Chik, 1868 A. D., they were abandoned partly because of the Mohammedan rebellion in Yunnan, which made life and property insecure, but largely because of the difficulty of operating the mines on account of water and poor ventilation. Since that time practically nothing was done, although the Burmese kings are said to have made several sporadic attempts to work the mines, until 1891 when Europeans were attracted by the great slag dumps (assaying about 40 per cent. lead) which the Chinese had left after extracting the silver. After a railroad and smelter had been built and 200,000 to 300,000 tons of slag smelted for lead, exploration work was started and old workings cleaned out in order to locate the remnants of the orebody that it was supposed the Chinese had left. After two years of most discouraging work, the remains of a large orebody was discovered by the Dead Chinaman Tunnel or what is the 171-ft., or No. 2 level adit. From then on the development was rapid and today the Chinaman is considered one of

Jan 1, 1923

By McDowell Graves, Joseph Jensen, W. D. Goold, M. L. Gwin

During the present year the Santa Fe Springs field has proved to be the most important oil field under development in the United States. Its production will exceed that of any other field. Without it, production within the United States would have been almost in even balance with consumption. The field has forced to the fore and compelled, more than any other single factor, serious consideration of the need of conserving the gas resources of the State of California. It has also contributed much to the development of new drilling equipment and important features in petroleum engineering, and has required the development of a new cement for use in deep wells because of high temperatures. It is the only oil field in the country where wells 8000 ft. deep have become so common that they are no longer given special attention. The field covers a little less than 1400 acres of land. In it 196 producing deep-zone wells have already been drilled since August, 1928, and 224 wells are still drilling. More wells may be drilled. This indicates that probably more than 450 wells will be drilled in the present campaign. In hardly a year's time it has caused the outlay of nearly $50,000,000 for drilling, and within the year 1929 it will have returned practically an equal amount of revenue. In contrast to conditions during 1923, when this field was once before an important and disturbing factor, the California oil industry has not been forced to refinance to meet the situation presented by such a large production of oil. There has been practically no unit selling and no stock selling, nor any unnecessary development far beyond the limits of the field. Production is now about 275,000 bbl. per day and gives every promisc of remaining at this figure or increasing to nearly 300,000 bbl. Six months from now the field should still be capable of producing more than 200,000 bbl. per day. Obviously, the need for conserving gas that would be blown to the air, incident to the production of so large a volume of oil, represents a problem in conservation deserving of the most serious attention of the oil industry and of the State of California.

Jan 1, 1930

As far as rapid determination of oxygen in liquid steel by means of a galvanic cell is concerned, I should like to summarize in a few words the activities of Centre de Recherches Metallurgigues (CRM) in Belgium. This work has been conducted both in a laboratory (Tammann and Induction furnaces) as well as on an industrial scale (converter and ladle). The galvanic cells developed by CRM are of two kinds: one with an air reference and one with a solid reference. As far as galvanic cells with air reference are concerned, we have tested numerous solid electrolytes (zirconia, spinel, and alumina). We finally chose zirconia sheathed with quartz. In order to be in a position to accurately determine the time when thermal equilibrium is reached, it was deemed useful to fit the galvanic cell with a Pt/Pt, Rh thermocouple, so as to follow the temperature variations at the interface of the solid electrolyte, until the temperature becomes equal to that of the bath. In actual fact the solution is highly interesting since it is possible to determine both the oxygen activity and the temperature of the bath with a single cell.

Jan 1, 1972

By S. H. Shepard

During the past year, a number of significant events have occurred in the nuclear industry. These include a surge in nuclear power plant orders, delays in nu- clear plant licensing and construction, increased environmental concern and the new Atomic Energy Commission nuclear fuel policy. These events, particularly the AEC stockpile release policy, have lead us to take this opportunity to update National Nuclear Corp.'s (NNC) appraisal of the outlook for the U.S. uranium industry.

Jan 10, 1972

By R. H. Lee

So far as I am aware the references to the " kerosene blow-pipe" in the Transactions comprise only a skeptical opinion from Mr. Witherow (ix., 70), and accounts of the use of the blow-pipe by Mr. Witherbee (xiii., 675) and Mr. Gayley (xiv., 779), together with brief remarks by Mr. Weeks and Mr. Kennedy on Mr. Witherbee's paper. The subject can scarcely be considered novel, in view of these references, yet it is not so far exhausted that an additional account of the successful application of the blow-pipe would be out of place, especially if accompanied with some new details and a drawing of the apparatus itself, showing its simplicity and safety. Some time ago, owing to a variety of causes, my furnace was working very badly, the troubles culminating suddenly one morning in a chilled hearth, solid from the bottom to the tuyeres, with the exception of a narrow passage-way from above to the cindernotch, which remained open. Through this we continued to flush and cast, with the prospect of a long and troublesome siege, in working down to the iron-notch. At the end of two days matters had not greatly improved, and we seemed no nearer the desired result than on the morning of the chill, when, at the suggestion of Mr. Farrell, of Glamorgan, I decided to use the coal-oil blow-pipe; the intention being to cut a hole from the iron-notch up to the tuyeres, and then let the furnace melt out the chilled mass. In four hours from the time of starting, the hole was made and

Jan 1, 1887

By H. W. McQuaid

IT IS usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effect of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide can result in total unfitness of low-carbon steel for, case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 2, 1922

By Stanley L. Lopata, Eric B. Kula

SEVERAL methods are available for determining pole figures by X-ray means.' The earlier film methods have been replaced by techniques in which the intensities are measured by Geiger counters on an X-ray diffractometerZm7. These methods utilize either flat transmission or reflection samples,214°8 cylindrical specimens,3 or spherical specimens.7 A single transmission or reflection sample will not yield information over the complete pole figure. The cylindrical specimens suggested by Nortod and the spherical specimen of Jetter and Borie7 have the advantage of allowing the whole pole figure to be obtained without any corrections to the intensity for absorption, There is a lower limit to the size of sheet which can be conveniently studied, however, and sample preparation can be rather tedious. Probably the most common method today for determining the complete pole figure is that developed by Schulz. A flat reflection sample is used for determining the pole figure from the center out to about 70". Because of the geometry of the system used, little or no correction for absorption or irradiated volume is necessary.4'6 A separate transmission sample is used for the region near the edge of the pole figure. This procedure requires two separate samples, one of which must be a thin carefully-prepared transmission sample. Furthermore, since the reflection and transmission data are in different arbitrary intensity units, a region of overlap must be obtained, and the intensity data from one set of measurements converted to units of the other. These are serious disadvantages of this method, and they point out the need for a simplified procedure. Since the reflection technique can be used for planes whose normals lie up to about 70° from the sample surface normal, it is apparent that a complete pole figure can be obtained by reflection alone if sample surfaces are cut at oblique angles to the rolling plane Specifically, if a rolled sample is cut so that the normal to the surface formed lies equidistant (54" 44') from the rolling plane normal, rolling direction, and transverse direction, then complete information for one quadrant of the pole figure can be obtained by reflection from the surface. Fig. 1 shows this oblique surface, as well as the position of the pole of this surface in the pole figure. When a surface has been cut oblique to the rolling plane, the standard polar stereographic net is inconvenient to use, and it would be more desirable to have the center of the net coincide with the pole of the oblique plane. Fig. 2 shows such a net, where the center has been offset 54' 44' to correspond to a specimen cut as in Fig. 1. This net was in effect obtained by rotating a standard polar stereographic net 54" 44' with the help of a Wulff net. With the experimental setup used. a sample can be cut from plate of 1/2-in. thickness or br Gen- erally thinner sheet is under investigation, and a composite specimen must be used. A convenient procedure has been to bond together, using epoxy resin, sufficient sheets to form a cube. These are clamped in a vise, and when dry, the whole vise is rotated and a flat surface ground at the required angle. The sample is then mounted inside a larger steel ring using Koldmount, the backside ground flat and parallel to the approximate desired thickness. The sample is then polished and etched to remove any effects of cold working during grinding. With this method only one quadrant of the pole figure is obtained. Often pole figures show symmetry around the rolling and transverse directions, and any slight asymmetry is due to scatter. Should the pole figure not be symmetrical, four oblique surfaces, corresponding to the four quadrants of the pole figure, would have to be examined. In most cases there is symmetry at least around the rolling direction, which reduces to two the number of quadrants to be investigated. For many purposes all that is required is an average polefigure for the four quadrants. This canreadilybe obtained with composite specimens of sheet material, where sheets Corresponding to each of the four quadrants can be intermixed. The four quadrants can be obtained by considering sheet in the normal position, and by rotatiolls of 180" around the sheet normal, the rolling direction, and the transverse direction. If desired, the whole thickness of the sheet can be used, yielding an average of the surface and interior textures; or the surface material can be removed from each sheet, resulting in a pole figure for the center alone. Eugene S. Meieran of the Massachusetts Institute of Technology has independently developed the same method. His results, adapted to a pole figure goniometer with a specimen spiraler, will be described in another publication.

Jan 1, 1962

By R. B. Snow

THIS paper describes a technique of polishing and etching specimens of open-hearth furnace slags or hearth aggregates for identification of the crystalline constituents-lime (CaO), tricalcium silicate (3CaO•SiO2), dicalcium silicate (2CaO-SiO2), monticellite (CaO•MgO-SiO2), or forsterite (2MgO•SiO2), with especial emphasis on the mineral merwinite (3CaO-MgO.2SiO2). With proper standardization, this identification does not require the use of the petrographic microscope. The composition of basic open-hearth slags and furnace bottoms falls, almost without exception, within systems containing CaO, MgO, "FeO," MnO and SiO2, in which the number of basic molecules so greatly exceeds the orthosilicate ratio (two molecules of base to one of silica) that free basic oxides, and combinations between them such as aluminates or ferrites, are present in cooled specimens. Orthosilicates of (CaO + MgO) are the most common in such specimens, since in nearly all cases, except premelt slags, the molecular ratio of (CaO + MgO) to SiO2 is more than 2 to r. When sufficient lime is available it combines with the silica to form dicalcium silicate (2CaO•SiO2), which contains little, if any, MgO, FeO or MnO in solid solution whereas the latter oxides combine to form the oxide solid solution known as periclase. If the lime present is insufficient to form dicalcium silicate (2CaO•SiO2) it combines with MgO to form either merwinite (3CaO•MgO.2SiO2) or monticellite (CaO-MgO•SiO2); these minerals take little if any FeO or MnO into solid solution and the remaining MgO, FeO and MnO combine as periclase. This generalization seems to be valid for basic slags and furnace bottoms, since minerals such as CaO-MnO•SiO2 and CaO-FeO-SiO2 are found only in slags in which the lime-silica ratio is less than 2 and are not observed in specimens from furnace bottoms. The identification of crystalline constituents in such materials, especially of fine crystals in the groundmass, is difficult under the petrographic microscope. They are often masked by their neighbors because of their small size in relation to the thickness of the thin section and because of the presence of opaque or colored constituents. The indices of retraction and the optical sign of the mineral are sometimes difficult to determine because of the small size or because of twinning or of inclusions within the crystal. Moreover, the positive identification of merwinite (3CaO•MgO.2SiO2) from its optical properties is usually difficult in the presence of dicalcium silicate (2CaO•SiO2). CaO, MgO, 3CaO•SiO2 and 2CaO•SiO2 in open-hearth slags have been identified for a number of years in the U.S. Steel Corporation Laboratory by the usual

Jan 1, 1947

FOR four years your Committee has been engaged in the study of problems connected with the educational preparation of professional geophysicists. The present report represents the conclusions drawn from the investigations and deliberations undertaken since it was first organized. These studies have shown that the evolution of geophysics has proceeded along lines that differed from those marking the advance of classical geology. The latter science developed as a descriptive one, dealing with directly observable terrestrial phenomena, and the elementary, rational explanations that could be offered therefor. The fact that these phenomena were also chemical and physical in nature was seldom given more than passing acknowledgment. During the last half century, however, a new approach to problems of terrestrial phenomena has become of greater significance. This new attack has come through the sciences of physics and chemistry, as the people trained therein have investigated the facts of the earth as problems in their respective sciences. This development has been chiefly at the hands of European investigators, and European universities have long recognized it by establishing departments or institutions of geophysics. In the universities of North America, their arbitrary departmentalization into fields of physics, chemistry, astronomy, geology, etc., has prevented the academic recognition of such domains of science as geophysics and geochemistry. In consequence, the development of these subjects in the United States has been largely at the hands of nonacademic institutions, while the universities themselves are evidently in a state of confusion as to how the subject should be handled. In some places an attempt to teach geophysics is made in the physics department, in others in the geology department, in some in the engineering school, and occasionally as a cooperative effort; a Department of Geophysics is seldom found in North America. In some instances, proper academic planning has been precluded by interdepartmental jealousies, or by lack of appreciation of the significance of the subject. For the background upon which these conclusions are based, the reader is referred to reports previously issued or sponsored by your Committee. These reports are available from Institute Headquarters. The "First Report of the A.I.M.E. Mineral Industry Education Division's Committee of Geophysics Education, 1939," summarizes the replies received to question-

Jan 1, 1942

By Earl R. McMillan

Though much has been written during the past several years about the Russian success in using hydraulic jets for coal mining, little or none of the published information, in so far as this writer has observed, has been of any use or practical application in this country. It is true, according to their published reports, that the Russians were pioneers in the use of high-pressure water jets in the mining of coal. They report the use of water jets for this purpose as early as 1936. However, according to a survey of foreign literature on the subject made by the U.S. Bureau of Mines1 a few years ago, water jets in the USSR, as well as in other nations including New Zealand, Poland and West Germany, were used principally to sluice the loosened coal after it had been previously drilled and blasted, rather than to cut or break it from the solid face. The interest of the Northern Pacific in the potential application of a high-pressure water jet to the actual extraction of coal, particularly in steeply dipping beds, originated in a visit by this author to the operations of the American Gilsonite Co. at Bonanza, Utah, in March 1958. After seeing the extraction, on a commercial basis, of gilsonite from a 22-ft wide vertical vein of this solid material with a 3/8-in. diam stream of water under approximately 2200 psi, it was felt that, with some modifications, water jets were the solution to the problem of economically mining the steeply dipping (i.e., steeper than 20º) coal beds in the State of Washington.

Jan 6, 1962

The official Institute reports for the year 1929 were distributed in pamphlet form at the Annual Meeting, February, 1930, and were later included in Section 2 of Mining and Metallurgy, June, 1930, and thus made available to the entire membership. Membership In its report the Admissions Committee set forth the changes in membership during 1929, as follows: Total membership, Jan. 1, 1928, 8582; elected and placed on rolls in 1929, including 59 reinstatements, 509; loss by resignations in 1929, 88; loss by death in 1929, 110; loss by suspension in 1929, 37; membership at end of year not including Student Associates, 8856. Distribution of membership: Honorary Members, 16; Members, 6590; Junior Members, 38; Associates, 1041; Junior Associates, 1033; Rocky Mountain, 138; total membership, Jan. 1, 1930, 8856; Student Associates, 150; total including student associates, 9006. Treasurer's Annual Report, Year of 1929 Statement of Receipts For the year ended December 31, 1929 Dues: Arrears............................................ $ 3,501.75 Current............................................ 97,257.12 New Members...................................... 5,721.50 Advance........................................... 1,970.79 $108,451.16 Initiation Fees.................................................. 7,436.OO Magazine Receipts: Advertising Gross Receipts........................... $40,610.81 Magazine Sales..................................... 3,799.84 44,410.65 Sale of Transactions Current........................... $ 2,985. 15 Sale of Special Editions Current........................ 5,147.82 Sale of Back Transactions and Special Editions........... 4,186.93 Sale of Year Book..................................... 65.50 Sale of Authors' Reprints.............................. 2,585.40 Sale of Pins and Fobs.................................. 14.73 Sale of Technical Publications.......................... 1,451.55 Sale of Bindings...................................... 3,949.13 20,376.21 Net Interest Received: On Bank Balance and Temporary Investments......... $ 2,595.04 On Lie Membership Fund........................... 3,223.43 On James Douglas Library Fund...................... 5,425.61 On General Reserve Fund............................ 2,015.58 13,259.66 Miscellaneous Receipts........................................... 335.80 Total Receipts................................................ $194,269.48

Jan 1, 1930

By G. W. Crane

WHEN ore was discovered on the Tintic Standard property in the spring of 1916, new developments were immediately started both north and south of that property, on the supposition that in East Tintic the ore would be found to occur in northerly trending channels, similar to those so characteristic of the older camp. But 9 years of developments have failed to establish the existence of such a channel. This is due undoubtedly to important differences in the geology of the two camps, that were not recognized, and is indicative of the danger in the general tendency toward interpreting the geology of East Tintic too strictly in terms of that of the older camp. It should not be forgotten that while the two sections have had practically the same geological history, the net results of a long series of geologic processes have developed in them conditions that differ so widely and in so many particulars that the necessity of regarding them as essentially different districts seems apparent. In an effort to emphasize this fact, this paper is devoted chiefly to a comparison of the geological conditions as found in the two camps and is addressed more particularly to those familiar with the geology of the Tintic district. Following a short description of the several ore discoveries and of the Tintic Standard mine is a brief discussion of the evidence of ore channels in East Tintic. For my information regarding the Tintic Standard mine, I am indebted to the courtesy and generous assistance of Messrs. Wade and Snow of the Tintic Standard Mining Co.

Jan 9, 1925