Search Documents

By Lawrence Addicks

AT the San Francisco meeting of the Institute last year, I presented, through the courtesy of Dr. James Douglas; some results of experiments on the roasting and leaching of concentrator tailings. After it became apparent that flotation rather than leaching was clearly the better method of handling the particular problem under consideration, before dismantling the experimental equipment, some data were secured on roasting and leaching the concentrate itself in competition with smelting. Some of the results obtained are given in the following paper and they a re of particular interest at this time in. view of the large quantities of flotation concentrates with their somewhat difficult smelting characteristics now being produced. A complete wet process? consists of roasting and leaching the calcines in dilute sulphuric acid produced from the roaster gases, roasting the residue with salt and leaching with dilute tower liquors (the well-known Longmaid-Henderson process) and recovering the copper, silver and gold by cementation or electrolysis or a combination of both. It is evident, however, that the residue from the first leaching, carrying about 20 per cent. of the copper and all of the silver and gold, can be smelted if preferable. In considering the application of the scheme to individual cases, it must be remembered that freight plays a. large part in any reduction process wherein smelting is not conducted at the, mouth of the mine, and that it is not practicable today to build small smelting plants for individual operations. The experiments may be grouped under four main heads: Roasting, leaching, chloridizing residue, and recovery of copper from solutions. The products of two concentrators were used: The Nacozari concentrates were the product of a large modern mill not using flotation, the copper mineral being largely chalcopyrite; and the Tyrone concentrates, the product of an experimental mill including flotation, the copper mineral being chiefly chalcocite. Typical analyses would be as follows:

Jan 9, 1916

By L. A. Price

With increased stripping ratios and with dwindling ore content, the mining fraternity is increasingly turning to larger and larger equipment for profitable open pit operations. The availability of higher horsepower prime movers and increased-capacity electric transmissions using either wheel-mounted or axle-mounted traction motors makes a reality of single-axle, rear dump trucks having 150 to 250 ton capacity. The size of electric loading shovels is inherently geared to the size of haulage equipment. To work effectively with this new generation of trucks, the Harnischfeger Corporation has introduced its P&H Model 2800 with a capacity of 20 to 25 cu yd and a working weight of nearly 1,500,000 lb. The Model 2800, depicted in Figure 1 loading a 200 ton truck, has many new electric and mechanical features designed to give excellent production and low cost operation. Chief among the new features is the ELECTROTORQUE control system. Electrotorque is a completely static, solid state electronic system supplying controlled power both to the armatures and to the fields of the d-c shovel drive motors. It eliminates many major electrical rotating machines and their attendant maintenance. The system was developed jointly by ASEA of Sweden and Harnischfeger Corp.

Jan 1, 1970

By C. E. Van Orstrand

An intrusive body is a mass of igneous rock that has migrated upward, presumably from great depths. Great variations in form, composition and depth of burial occur. It is not proposed in this paper to go into all of the details of the problem. Instead, it mill be assumed here that the intrusive has the form and characteristics represented in Fig. I. According to W. 11. Emmons minerals are not deposited in appreciable quantities below the "dead line." Important amounts of ores of virtually all metals may be found around summit cupolas, but only gold, copper and zinc (in limited quantities) are usually associated with trough cupolas. Most students of ore deposits agree that temperature changes are largely instrumental in precipitating many ores in the "hood" and that the difference in temperature between the intrusive and that of the country rock may be the chief factor in determining the mineralogy of a deposit. A problem then of some interest is to correlate the principal physical features of the intrusive with the phenomena of heat conduction as evidenced by the cooling curves and the isothermal surfaces. Mathematical Theory In order to show the possible application of heat conduction to the interpretation of the processes of metalliferous deposition associated with intrusives, it will be as- sumed that the intrusive is a large par-allelopiped of dimensions, 2l, 2m, 2n. The equation that represents the flow of heat from the parallelopiped into country rock (v = o, 1 = o), which has the same thermal properties as the intrusive, is2,3 l-x v I FT 2 [2 2 — l-x m — y — m — y n — z In this equation, the origin, x = o, y = o, z = o, is at the center of the parallelopiped. v = temperature at point x, y, z, time 1. v, = initial temperature throughout the intrusive, 1 = o. k = coefficient of thermal diffusivity. a, ß, y are variables of integration. Put n = m in Eq. I, and we have v I [2/5 [2I-x 2 — l-x m — y 2 2 2 kt 2 20xt e-a2da ebrdß

Jan 1, 1946

By John H. Hollomon

IN recent papers, O'Neill,1 Vivian,2 and Zener and Hollomon3 have reviewed some of the information concerning the relations between stress and strain during plastic deformation. Since further information has been obtained since these reviews were published, this paper attempts to further coordinate and amplify the knowledge concerning the plastic deformation of metals in simple tension. Ordinarily the results of tensile tests of metals are presented as graphs in which the load divided by the original area is plotted as a function of the percentage of elongation measured over some specified gauge length. The interpretation of graphs of this sort is limited, since the stress required to deform the metal at any stage of the deformation is actually the load divided by the instantaneous rather than the original area. Furthermore, each increment of the deformation is performed on metal that has been previously deformed, and, as pointed out by Ludwik,4 the strain could be more effectively defined: [e = In A t][I] where a is the strain and Ao and A are, respectively, the original and instantaneous areas. The results of the tensile tests can be more effectively presented and interpreted if the stress* (load divided by actual area) is plotted as a function of the strain as defined above. A schematic curve of this type is presented as Fig. I. In a previous paper,6 the concept of Ludwik7 concerning the flow and fracture of metals was successfully employed to explain some of the puzzling results of notched-bar impact tests of steel. It appears that the use of this concept is very fruitful and should be kept in mind in any study of the deformation characteristics of metals. Ludwik considered that a flow stress-strain curve of a metal was essentially a locus of points that described the stress required for plastic flow of an infinite number of specimens, each with a different strain history determined by the preceding part of the flow curve. Each of these specimens can also be considered to have a fracture strength. Unfortunately (or fortunately depending upon the point of view), all the specimens, except the one deformed to the fracture strain, flow and do not fracture. Even though the metals do not fracture, the concept of a fracture-strength curve seems

Jan 1, 1945

By H. E. Doerr

The writer has been unable to find much information relative to tests made to determine the effect of forging on the specific density of steel. The opinion, however, among men engaged in the business, seems to be that forging greatly compresses or consolidates the steel. While such is doubtless the case with spongy or porous steel, the following experiments indicate that there can be little or no change in the density with steel initially free from cavities. Ten ingots of basic open-hearth steel cast as shown in Fig. 1 were used in the experiments. All the specimens were 0.53 carbon with all other elements the same, the analysis being determined from drillings taken midway between the center and outside of the upper end, as shown in Fig. 2. The specimens were selected from over one thousand ingots so that the tests could be comparative for the work done in forging only, but no two of the ingots were cast in the same heat. Each ingot remained in the mold approximately 30 min., when it was removed and sir-cooled. About 12 hr. later, when the temperature had been reduced to approximately that of the surrounding atmosphere, the head was discarded and the ingot heated in an oil furnace to approximately 2250" F. (1235" C). Approximately 1 min. was required to forge under the steam hammer to 1 1/4 in. (31.75 mm.), rough diameter, as shown by the dotted lines in Fig. 2. All ingots were allowed to air-cool after forging. Cylinders 1/2 in. (17.7 mm.) in diameter and 1/2 in. high were then turned from the forged and unforged parts of the ingots and numbered. The ten pairs of specimens were submitted to Louis E. Endsley, Professor of Railway Mechanical Engineering, University of Pittsburgh; A. N. Talbot, Professor of Applied Mechanics, University of Illinois; L. Z. Slater, chief chemist, Scullin Steel Co., St. Louis, Mo. NO information was furnished as to which specimens were forged or unforged and each laboratory used the same specimens, submitting the average of three independent determinations, a tabulation of which is shown in the accompanying table in which the laboratories are designated by the letters A, B, and C. While there is considerable difference in the individual determinations for a number of the specimens, the averages

Jan 1, 1920

By D. C. Holloway

Ceramic projectiles made from 94% to 99% alumina with a nominal mass of 3.1 gms were fired into granite blocks. The average compressive strength of the ceramic was 800 MPa and that of the rock was 135 MPa. Flat, ogive, conical and pyramidal nose shapes were evaluated at velocities ranging from 450 to 1400 m/sec. It was found that the conical and pyramidal nose shapes at the higher velocities did a significant amount of damage to the rock. On the average, they removed 10 5mm3 of rock and were six and ten times better than the flat and ogive nose shapes. It was also observed that increases in volume occur in discrete steps. This process is highly dependent on the ability of the projectile to penetrate the rock.

Jan 1, 1984

By Richard Conkling

A SHALE layer, buried beneath two or three thousand feet of strata, in some instances, will upon folding become thicker in the synclines and thinner on top of the anticlines. This can be accounted for, in part, by the stretching on the crests of the fold and the compressing in the troughs; but this will by no, means account for all of it, as is shown in the example herein set forth. It is my firm belief that the rest of the thickness is due to flow. What causes the movement, however, does not concern us here, so long as there is movement, for this article purposes to show its effect upon the producing area of different sands. It is the author's hope, in this way, to drop a hint or two that may be valuable to the oil geologist, in making estimates of future productions and values of oil properties. An example will be given from property in the famous Cushing Pool in northeastern Oklahoma, where the author has had occasion to make a detailed study before recommending some property to his company, and has then been able to watch the results of this work. The author never mapped the surface structure in this pool, as this had been done by Frank Buttram when he was with the Oklahoma Geological Survey. We are using, therefore, a section of his map in this article for our surface contours. The main east clip comes farther east than this section shows.

Jan 10, 1916

By L. C. Raymond

Why, in an age when natural resources are available on a scale heretofore unknown, and when there is an unprecedented need for them to be developed, have would leaders been unable to find solutions which world concert the under-developed nations into developing nations? With investments in natural resources declining relative to world needs, it is necessary to reverse this senseless trend. This article is an examination of the paradox based on worldwide aspects of the mineral development field, and suggests a possible solution.

Jan 8, 1964

INTRODUCTION Engineering studies of many near surface coal deposits that are amenable to strip mining can be enhanced and expedited by the application of computer techniques for defining coal reserves and overburden and intraburden yardage and their stripping ratios. The case study discussed herein could be from the western coalfields of Colorado, Wyoming, or Montana; the lignite deposits of the Dakotas or Texas, or from the strippable coal seams of the midwest. Because the techniques can be applied so universally, the actual map locations are not identified. The same computing principles apply to one seam or multiseam deposits, and the capability of the computing programs and plotting routines to display the coal seams in plan and sections provide excellent base maps for further engineering planning and mine layout studies. MANAGEMENT OF DRILL HOLE DATA Drilling for coalfield information is usually done at much wider centers than for other mineral deposits. The geologic logs of the holes are generally quite simple, and frequently record only major lithologies and depths to the top and bottom of the coal seams, together with hole collar survey information. A header card is prepared for each drill hole showing: Hole ID Northing Fasting Elevation Azimuth Dip The header card can be followed by any number of downhole lithologic intercept records: [Hole Depth Lithology Hole ID From-To Coal] Less data errors occur if the computer cards are punched directly from drill hole logs, thus eliminating opportunities for mistakes in transcribing data. All arithmetic manipulations should be left to the computer to avoid as much human error as possible. The SURVEY program is run over the raw data file and all lithologic intercepts are computed and defined in XYZ space. BOUNDARY SURFACES-COAL SEAMS AND LITHOLOGIC UNITS The most useful computer program for defining coal seams in 3D space is a linear inter-

Jan 1, 1980

By James W. Halley

"Fine-grained" steels have been standard products for many years. This paper describes an investigation of the effects of some of the more common grain-growth inhibitors used to produce these steels. The properties, response to heat-treatment, and the deoxidation practice necessary to produce "fine-grained" steels have been the subjects of numerous papers. It has been shown that a substantial quantity of aluminum is necessary to produce this type of steel, and it has been indicated that titanium and zirconium produce a similar result. For some time there was a lively argument between those who felt that aluminum refined the grain and those who felt that aluminum oxide was the effective agent. This argument subsided with an apparent victory for those promoting aluminum oxide. Most of the work on grain size has divided steels into two broad classifications based upon McQuaid and Ehn's original carburizing test at 1700°F or some similar test at this temperature. If the steel coarsened at this temperature, it was coarse grained, while if it did not it was he grained. Quantitative data concerning how much a certain amount of aluminum raised the coarsening temperature and affected the properties, all other factors being constant, are very meager. Similar information regarding titanium and zirconium is practically nonexistent. The published information on aluminum yields some quantitative information. Epstein, Nead and Washburn' gave the first quantitative information on the amount of aluminum necessary to prevent grain growth at 1700°F. They showed that the addition of a pound to a pound and a half of aluminum per ton (0.05 to 0.075 per cent) would assure steel that would not coarsen during a McQuaid-Ehn test at 1700°F. Herty, McBride and Houghg reported that a steel containing 0.020 per cent acid-soluble aluminum coarsened between 1742° and 1832°F., while steels containing 0.016 per cent and 0.017 per cent acid-soluble aluminum coarsened between 1652° and 1742°F. compared with similar aluminum-free steels that started to coarsen at 1580°F. Herty3 also showed a marked improvebent in low-temperature notched impact resistance with increasing acid-soluble aluminum up to 0.030 per cent. McQuaid4 compared the coarsening of steels containing 0.011 to 0.204 per cent total aluminum and found a maximum coarsening temperature at 0.098 per cent aluminum. He had no samples between 0.015 and 0.098 per cent aluminum. Houdrement6 found a marked decrease in coarsening temperature with aluminum contents above 0.50 per cent. Kinzel, Crafts and Egan6 found that aluminum and zirconium improved the low-temperature impact resistance of a low-alloy steel, while titanium was detrimental. Sims7 shows that sulphur increases the coarsening temperature and that the maximum coarsening temperature is between 0.04 and 0.06 per cent added aluminum. The fact that the coarsening temperature passes through a maximum with increasing aluminum content appears to be well established. The aluminum content that

Jan 1, 1947

||Abad, Leopoldo F., Min Engr, Div of Mines, Bureau of Science Manila, P I '23 Abadilla, Quirico A, Geol, Lago Pet Corp Box 172, Maracaibo, Venezuela '20 ||Abbey, Robert Graham, The W W Sly Mfg Co Train Ave, Cleveland, Ohio '21 Abbott, A. N., Mines Supt, Mazapil Copper Co, Ltd Concepcion del Oro, Mexico '23 Abbott, Clarence E., Mgr, Mines & Quarries, Tenn Coal, Iron & R R Co, 1242 Brown Marx Bldg, Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr , Consolidation Coal Co , Elkhorn Div Jenkins, Ky. '16 Abbott, Robert R., Met Engr , Peerless Motor Car Co Cleveland, Ohio '12 ||Abbott, Wells Osborn, Ray Consolidated Copper Co Hayden, Ariz. '23 Abeel, George H, Jr., Cons Min Engr 4612 West 17th St , Los Angeles, Cal '18 Abel, Albert E., Asst to Pres, Valley Mould & Iron Corp Sharpsville, Pa. '19 Abernathy, George Elmer, Prof of Geol & Min , Kansas State Teachers College, Pittsburg, Kans. '20 Abey, Hiroshi, Min & Met Engr, Min & Met Dept, The Higher Technical School, Osaka, Japan. '17 ||d'Ablaing, Philip R, Chem , Anaconda Copper Min Co Great Falls, Mont '25 Aborn, Robert H , Research Assoc., Mass Inst of Tech Cambridge, Mass '19 Abouchar, Sylvain Sley, Min. Engi & Geol , care of S H Sekaly, 13 Rue El Nimr, Cairo, Egypt '17

Jan 1, 1923

By G. C. Weaver, G. T. Harley

Beds or lenses of potash and magnesium salts are found in a thick salt section (Salado) overlain by Rustler Red Beds in several members of which water is present and from one of which the rehery process water used by International is obtained. Most of the holes drilled are less than 1000 ft. deep, but some wildcat holes have exceeded 3- ft. cable or rotary tools are used to drill down to the salt. when samples of water are desired the cable rig is used, but when this is not necessary, and where caving material is present, the rotary rig has an advantage. The rotary rig has a further advantage in that only one machine is required to drill and core the entire hole, whereas the cable rig must be moved off to make way for the core drill. Casing is placed in the upper section of the hole as required to shut off water, and a 5 3/16 in. string is set in the top of the salt before coring starts. With the rotary rig drilling is often carried to the salt with no casing, as drilling mud seals off caving ground and water-bearing strata, and a string of 4-in. line pipe or 4-in. flush-joint casing is landed on top of salt. Several types of gasoline-powered core rigs have been used in the field and all recover a 2 1/2-in. core. More recently the Sullivan Model 37 rotary rig has been tried, and a Sullivan Model N has been adapted to use a rotary bit in the upper section. Core is recovered in 20 ft. sections with a double-tube core barrel, and the bit used is a bottom-discharge type set with diamonds. The drilling fluid must be a saturated brine to prevent solution and etching of the minerals present. Blowouts are apt to Occur from nitrogen gas trapped under the several polybalite beds, and some have been strong enough to blow the tools out of the hole. Core recovery is practically loo per cent. All holes are plugged after drilling, with cement through the salt section and opposite each water horizon* and mud through the remainder of the hole. Cores are carefully logged and preserved, and in sections containing potash and magnesium minerals they are quartered and analyzed. The correlation of Ore beds between drill holes is briefly described. Introduction Beds Or lenses of potash and magnesium salts are found at varying depths in a thick deposit of salt (Salado formation) in what is known as the Permian Basin, in southeast New Mexico and West Texas. The Salado formation is Composed chiefly of common salt (halite) with numerous beds of anhydrite, polyhalite, and the soluble potash minerals carnallite, sylvite and langbeinite. Many other minerals are present in small amounts but their Presence has no bearing On the coring technique. Before starting to core the salt section it is necessary to penetrate 300 to 600 ft. of unconformably overlying Permian sediments (Rustler formation) which are composed of red and gray clay, sand, anhydrite, dolomitic limestone and occasional lenses of salt. The upper part of the formation is predominantly anhydrite, and the lower part predominantly clastic. A thin bed of dolomitic limestone, known

Jan 1, 1948

By R. S. Hooper

In attempting to describe recent mining developments at the Bunker Hill mine, it may be well to recall first the old days of hand mining when holes were laboriously drilled by hand to a maximum depth of three feet, and were shot one or two at a time, in order that the miner could take advantage of every slip, crack or bedding plane, and so save as much drilling as possible. Broken muck, of course, was loaded by hand shoveling into wheelbarrows or small cars, and heading advances or stope tonnages were governed by the number of men that could find room to work in any given place. The first big improvement over these old methods was the introduction of the reciprocating type of air-powered rock drill. This innovation, crude as it was, enabled the miners to set up a machine and drill a complete round of holes in one shift; but broken muck was still loaded by hand, and the size and rate of advance in headings were limited by time required to remove the broken rock. The next improvement of consequence was the appearance of the hammer-type rock drill, which greatly increased drilling speed over the reciprocating type, and made possible the completion of a full cycle in one shift, by the use of crossbars in headings, and permitted drilling and mucking to be carried on at the same time. Rock drills continued to improve as time passed, and finally the smaller and more efficient mucking machines appeared on the scene, and it became possible to muck out a round of broken rock and have a clean setup for one or more drill columns and machines. A complete cycle of mucking, drilling, and blasting was completed in one shift with an average advance of five feet. These conditions prevailed for several years, but as the mine grew deeper, the distances to transport the workers grew longer, and this fact together with the shortening of the working day, soon presented the problem of attempting to complete a cycle of operations in a shift of only six hours at the working faces. Anticipating this condition, the operating heads at the Bunker Hill had started an intensive study of more and better mechanization, and over a period of comparatively few years have adopted and placed in service methods and machines that make it possible for a three-man crew to consistently advance headings seven by nine feet in cross section, at the rate of eight feet, and more, per shift, doing all the mucking, switching, drilling and loading. These improvements consist of the following major items: I. The development of a light, flexible, easily transported jumbo equipped with pneumatic columns (Fig I), that has decreased the "setting up" and "tearing down" time an average of 11/2 hr per shift, Or 25 PCt of the available working time. These jumbos were developed at the Bunker Hill mine by members of the staff and consist of two pneumatic columns attached to a suitable carriage. They fold

Jan 1, 1949

By John J. Curzon

The existence of mineralized ground in the area near Lake Chelan has been known since 1887, when Major A. B. Rogers, a locating engineer for the Great Northern Railway, came up Lake Chelan to Railroad Creek in search of a pass over the Cascade Mountains. The steep mountainsides near the crest of the Cascades proved too difficult for railroad construction, and the project was abandoned. Upon his return to Seattle, Major Rogers apparently told his friends, the Denny family, about the large, red, oxidized patches he had seen on the valley walls along Railroad Creek. The Dennys, being true pioneers in spirit, grubstaked J. H. Holden to explore the area and to stake any promising mining ground, and thus began the chain of events that culminated in the construction of the plant that is now known as the Chelan Division of the Howe Sound Company. Holden staked the first group of claims in 1892. Soon afterward, A. H. Murdock, who was then a storekeeper in Chelan, and who is still living at Waterville, and his partner, W. P. Robinson, staked adjacent ground. These two groups of claims formed a substantial part of the mining property being worked today. During the period from the original staking in 1892 up to 1928, when the Britannia Mining and Smelting Co. optioned the property, many attempts were made to bring the property into production, through the formation of several stock companies and by examination and testing by engineers from several well-known mining companies. Although the Britannia organization optioned the property in 1928, not much was done until 1930, when a subsidiary was formed—the Chelan Copper Mining Co.—to explore further the possibilities of the ground. Some work was done during the next few years, but it was not until March 1937 that the Chelan Division of the Howe Sound Co. took over with a program of "full speed ahead," and active development of the mine and construction of the complete plant was begun, including docks, tug and barges, 54 miles of power line, 11 miles of road, mill, shop buildings and complete camp. Production began in April 1938, and has continued without interruption, except for regular change days and holidays and a six-weeks strike in 1939. This interval of time has seen the gradual evolution of a mine and mill originally planned for a rate of 1000 tons per day into a compact operation that last year averaged 2264 tons per operating day. This operation, although rather small when compared with the large copper producers of the Southwest, is important to the state of Washington for several reasons: It has provided employment for several hundred people continuously since construction days in 1937; it has helped materially in the war effort, through production of vital copper and zinc, without which no war can be won; and last, but not least, it has conclusively refuted the old pessimistic arguments that a successful mine would never be found in the Cascade Mountains of Washington. The Holden mine has been producing

Jan 1, 1946

By R. A., Pallanch

THOUGH the flotation of gold ores has come into the lime- light largely in recent years, it is not a product of recent economic conditions but rather as old as flotation itself. It could hardly be other- wise, since gold, when in the right state of comminution and surface condition, is one of the more readily floated of minerals. In early practice it was not generally recognized that gold was floated as well; it was - thought that the gold was bound up with sulphide minerals that floated, but now we know that free gold must have been floated as well.

Jan 1, 1935

Jan 1, 1903

By T. M. Allen, W. H. White

THE Greenwood-Grand Forks area of southern central British Columbia, known as the Boundary District, has a long history of mining exploration and production. At the turn of the century this was the premier copper mining camp in the British Empire, its total production amounting to some 20 million tons. Most of this ore came from the great Granby mines at Phoenix, but the Motherlode mine at Deadwood camp, 6 miles to the west, and several mines in Summit camp, 5 miles north of Phoenix, made important contributions. The large deposits were exhausted in 1918 and the district since has seen only desultory exploration and salvage operations. The orebodies are mineralized skarn zones in limestone members of a thick series of Upper Paleozoic sedimentary and volcanic strata. Chalcopyrite is the primary ore-mineral. Copper carbonates and silicates occur sparingly in outcrops, but the oxidized zone generally is very shallow. Much of the surface is mantled by glacial drift which in most places ranges in thickness from 2 to 15 ft. In some of the hanging valleys, however, the glacial drift may be as much as 100 ft thick and may assume drumlin-like forms. In 1951 an ambitious program aimed at the discovery of new orebodies and important extensions of abandoned deposits was launched by Attwood Copper Mines, Ltd. In this district so thoroughly searched by an earlier generation of prospectors, any orebody which had remained undiscovered must have little or no surface indication. Consequently, in addition to the basic detailed geological work, the program of exploration included magnetometer and self-potential surveys. Geological bets and geophysical anomalies were tested further, prior to diamond drilling, by a study of copper distribution in tree twigs and/or in the soil. The soil sampling and analytical methods used and some of the results seem of sufficient importance to warrant this paper. The authors had done some plant sampling in this and other districts, using the dithizone neutral-color-end-point method (Warren and Delavault, 1948, 1949; White, 1950),1-3 but they were unfamiliar with its soil application. Finally, after much experimenting in the field, they adopted the methods described here. These methods are not entirely original or defensible on theoretical grounds, but under field conditions of rapid sampling and analysis the results are reliable enough to be of use. Fig. 1, which shows the results of duplicate analyses of duplicate soil samples taken at 50-ft intervals across an anomalous zone, indicates the relative dependability both of the sampling and analytical methods. Sampling and Analytical Equipment A 2-ft piece of 1-in. solid drill steel, one end sharpened to a broad, conical point. The steel is marked at 1 ft from the point. A 2-ft piece of ½-in. black iron pipe, one end filed to a bevelled cutting edge. The pipe is marked at 1 ft 3 in. from the cutting end. A 3-lb hammer. A plastic or rubberized sheet about 18 in. square. Moisture-proof assay pulp envelopes. A 10-mesh seive made from window screen with the paint burnt off. A small assay spatula. A pan balance sensitive to 10 mg. Two ignition trays about 4 in. square, made of sheet iron turned up along the edges. A Coleman two-burner gasoline stove. An asbestos board about 5x8 in., used as a hot plate on the gasoline stove. A circular aluminum rack to hold 8 test tubes while refluxing (design of Almond and Morris). Pyrex Glassware Large refluxing test tubes, 25x200 mm, marked at 40 ml volume. Breakers, 20 ml. Pipettes, 1, 5, and 10-ml capacity. Graduate, 50 ml. Shaking cylinders, 100 ml, glass stoppers. Burette, 25 or 50-ml capacity, with holder. Chemical Supplies 1 N sulphuric acid. Hydroxylamine hydrochloride, solid crystals. Fisher Alkacid test paper. Copper standard solution. Dithizone standard solution 60 mg per liter. Water reasonably free of metals. Soil Sampling Method: The problem of how to take a soil sample is extremely crucial. The method outlined below, adopted after a number of tests, has the advantages of uniform pattern, uniform depth, and uniform size of sample. The area to be tested was marked off by chain and compass lines 100 ft apart, normal to the strike of possible ore deposits. Numbered stakes were set at 50-ft intervals along these lines and a soil sample was taken at each stake in the following manner. The drill steel was driven into the ground normal to the slope of the surface to the marked depth of 1 ft, moved slightly from side to side, then carefully withdrawn. The iron pipe was inserted to the bottom of this hole, tapped down to the marked depth of 1 ft 3 in. and withdrawn; the 3-in. soil plug in the

Jan 1, 1955

By R. T. Hukki

John F. Myers (Consulting Engineer, Greenwich, Corm.)—Since the art of comminution has lain practically dormant for many years, it is very interesting that R. T. Hukki approaches the subject with a new concept. One is reminded of the research carried on by A. W. Fahrenwald of Moscow, Idaho, a few years ago. Fahrenwald mounted a steel bowl on a vertical shaft. The balls and ore placed in the bowl were rotated at fast speeds, thus simulating the supercritical speeds used by Hukki. The rolling action of the balls against the smooth shell liner has pretty much the same effect. The action is horizontal in one case and vertical in the other. Both researchers report good grinding activity. It is also constructive that such able investigators give to the students of comminution their interpretation of their laboratory results in terms of large-scale operation. History shows that it takes a lot of time for such radically new ideas to be absorbed by the industry. Typical of this is the present-day activity of cyclone classification in primary grinding circuits. The idea of cyclone classification has been kicking around for 30 or 40 years. Certainly we all suspect that the ponderous grinding mills of today, and their accessory apparatus, large buildings, etc., will ultimately give way to small fast units, just as this has occurred in other industries over the past 50 years. At the moment there is no evidence that ball and liner wear is prohibitively high. In fact, at the time Fahrenwald was demonstrating his high-speed horizontal machine at the meeting of the American Mining Congress, several years ago, he assured this writer that the balls retained their shape much longer than they do in conventional tumbling mills. Rods and balls that slide (as some operators in uranium plants are experiencing) get flat. Apparently the balls have a rolling action. Mr. Hukki's references to the processing capacity of the Tennessee Copper Co. mills is adequate. Those studying this subject will be greatly interested in the paper presented by Richard Smith of the Cleveland-Cliffs Iron Co. at the annual meeting of the Canadian Institute of Mining and Metallurgy in Vancouver April 24, 1958. This paper will be published during the latter part of 1958 in the Canadian Institute of Mining and Metallurgy Bulletin. Hukki's pioneering spirit is to be commended. R. T. Hukki (author's reply)—It has been heartening to read the objective discussion by J. F. Myers. The sincerity of his opinions is further strengthened by the fact that the article he has discussed contradicts in a major way the parallel achievements of his life work. Myers is right in his opinion that in general it takes a long time before new ideas are accepted by the industry. On the other hand, revolutions usually take place at supercritical speeds. There are many indications at present that both the unit operation of grinding and the related subject of size control are now just about ripe for a revolution. In grinding, brute force must ultimately give way to science. Rapid progress can be anticipated in the following fields: 1) Autogenous fine grinding at supercritical speeds will be the first advance and the one that will gain recognition most easily on industrial scale. At this moment, little Finland appears to be leading the world. Crocker recently made a statement that in nine cases out of ten, your own ore can be used as grinding medium more effectively and far more economically than steel balls. This is true. The present author would like to introduce a supplementary idea: In eight cases out of the nine cited above, it can be done at the highest overall efficiency in the supercritical speed range. Fine grinding must be based on attrition, not impact. The path of attrition may be vertical, horizontal, even inclined. 2) In coarse grinding, the conventional use of rods is sound practice. However, even the rods can be replaced by autogenous chunks large enough to offer the same impact momentum as the rods. To obtain the momentum, the chunks must be provided with a free fall through a sufficient height in horizontal mills operated at supercritical speeds. Coarse grinding must be based on impact. Detailed analysis of the subject may be found in a paper entitled "All-autogenous Grinding at Supercritical Speeds" in Mine and Quarry Engineering, July 1958. 3) All conventional methods of classification, including wet and dry cyclones, are inefficient in sharpness of separation. Continuous return of huge tonnages of finished material to the grinding unit with the circulating load is senseless practice. In the near future the present methods will be either replaced or supplemented by precision sizing. These three fields are also the ones to which J. F. Myers has so admirably contributed in the past. Fine Grinding at Supercritical Speeds. By R. T. Hukki (Mining EnGineERInG, May 1958). Eq. 9, page 588, should be as follows: T , c, (a — 6') n D Ltph On page 584 of the article the captions for Figs. 4 and 5 have been placed under the wrong illustrations and should be interchanged.

Jan 1, 1959

By William J. Robinson

What is the cummulative rate of recovery of copper from a sulfide leach dump? The technical answers to this frequently asked question may vary from "I don't know" to "quite good" from people of the same company. Management also poses this question because it plays a vital role in planning future production. The answer is difficult because of the many variables between different operations such as physical construction of the dump, topography of the original site, characteristics of dump material, mineralization and water application. Each of these factors and others have a bearing on the rate of recovery. Anaconda's method of water distribution at Butte is unique in that each dump is drilled to allow physical injection of water into the dump. The injection holes are drilled vertically on 25 ft centers from the surface of the dump. Normally, the holes are drilled 40 ft deep and cased with 4-in. PVC perforated pipe. The pipe is perforated at one-foot intervals with four 1/2 in. diam holes at 90" spacing on the pipe circumference.

Jan 9, 1972

By Clarence E. Sims

An effort has been made to give both a comprehensive and simplified picture of the origin, modes of formation, and characteristics of nonmetallic inclusions in steel. Exogenous inclusions, those formed by mechanical entrainment or heterogeneous reaction, have their principal source in ladle refractories. Mechanical emulsion is not considered a likely mechanism. Endogenous inclusions, resulting from homogeneous reactions, are formed mainly during cooling and freezing. They are principally oxides and sulfides but include some nitrides and carbides. Deoxidation affects both the quantity and character of such oxide inclusions and significantly affects the size and shape of sulfides. The importance of inclusions is largely in their effect on mechanical properties. It is fitting and proper that we should honor the memory of those technical giants who have left such a rich heritage to our profession. Today, according to annual custom, we pay tribute to such a man. To have been chosen to play a part in this observance prompts in me an inordinate pride while I am humble before the responsibilities of my task. The ranks are growing thin of those who had the good fortune to come under the personal influence of Professor Howe, but the number who continue to benefit from his legacy of technical wisdom con-stantly increases. I am among the latter. One has only to read his works to appreciate his unusual ability to take data and observations from many sources and give them a clear and comprehensive

Jan 1, 1960