Search Documents

By L. S. Castleman, R. K. Hotzler

We are currently studying the effects on recrys-tallization of impurities diffused into dispersion-hardened alloys. Our interest in this phenomenon was originally aroused by the observation that the recrystallization temperature range of tungsten "doped" with alumina and silica, or with thoria, is lowered drastically if nickel is plated onto the tungsten prior to heat treatment.' In this note, we report a similar effect that sulfur has on the recrystallization behavior of thoriated nickel. The experimental procedure for this exploratory phase of the investigation has consisted simply in heating commercially obtained stress-relieved samples of thoriated nickel for varying temperatures and times in sealed capsules containing air and small quantities of sulfur. The samples contain 2.4 vol pct thoria and initially less than 18 ppm S by weight; they are prepared either from 0.5-in.-ciiam rod stock or from 0.092-in. sheet and are in the "as-received" (stress-relieved) condition prior to exposure. In an atmosphere free of sulfur, such samples do not show evidence of recrystallization after being annealed for 1 hr at a temperature of 2500°F (1372C).2 The photomicrograph in Fig. 1 shows the microstructure of one of our samples annealed for 75 hr at 1000° C (1832°F) in a sulfur-free capsule. The grain structure is hardly evident (if at all) at 465 times magnification. In contrast, the photomicrograph of Fig. 2 shows the recrystallization that has taken place in a sample exposed to sulfur for 5 hr at 1000°C (1832°F). A nickel sulfide phase is visible at the grain boundaries of the light-appearing grains. We have also observed recrystallization to occur in a sample annealed at 600°C (1112°F) for 25 hr. This temperature is below the 637°C (1178°F) eutectic in the Ni-S system. In the latter case, no nickel sulfide phase is evident in the microstructure. Moreover, we have noticed the occur-

Jan 1, 1969

By Norman L. Wimmler, H. G. Iverson, S. Ricker, P. E. Oscarson, S. H. Lorain

THIS paper has been prepared with the principal objective of recording the results of the Bureau of Mines exploration of five major clay deposits in the Western Region. It is based mainly on data contained in unpublished Bureau of Mines reports. Acknowledgment is made to the Federal Geological Survey for its cooperative work with the Bureau of Mines, to the various State geological and mining departments, and other State and local agencies. CLAY EXPLORATION BY THE BUREAU OF MINES Much has been written and published on clays and clay deposits relating to their refractory, ceramic, and other qualities but such literature is lacking in analyses of the available alumina content of the clays and provides little indication of their possibilities as a source of alumina. With this new objective in view, a great many of the known clay deposits were reexamined and new ones discovered. The Bureau of Mines made preliminary examination of numerous areas in the western United States. Five of those most favorably indicated were systematically drilled, and in each a large amount of high-alumina clay has been found. These five major projects are Molalla and Hobart Butte, in western Oregon; Cowlitz-Castle Rock, in southwestern Washington; Lone, in California; and the Olson-Troy area in Idaho (Fig. I). Preliminary scout drilling was done in the Stockton deposit at Coeur d'Alene, Idaho; the Whiteware deposit near Lewistown, Mont.; and 13 areas in the Spokane or eastern Washington region, where the most favorably indicated area, known as the Excelsior, is now being drilled more systematically. Preliminary drilling was undertaken in numerous areas adjacent to the major deposits and others more remote. As a result, large additional clay possibilities were found. THE CLAY DEPOSITS The clay deposits under consideration are of the sedimentary or transported types, parts of which have been altered further by the agencies of weathering, ground water, or hydrothermal action. There are extensive deposits of residual clays in northern Idaho and in eastern Washington, but they have been found to be low in the available alumina and to contain much free quartz, mica, and unaltered feldspar. To be of value, they must first be subjected to beneficiation to remove these gangue minerals. The sedimentary clays have been derived largely from the decomposition, erosion, and transportation of granites, gneisses, schists, and basalts. At Molalla, some

Jan 1, 1944

By L. R. Velho, N. A. D. Parlee, J. Gani

THE unsteady-state type of gas-liquid metal diffusion cell1 has found considerable application.2"4 Cells of this general design can function as steady-state cells if allowed to operate long enough to reach steady state. This report tells of some success in the adaption of this type of cell for steady-state work, using the 0-Ag system in which the mass transfer of the gas "species" is basically controlled by diffusion in the liquid. The gas, e.g-., O2, is maintained in the cell tube'-3 at 1 atm pressure, Fig. 1, by buret and sensitive oil manometer. The gas, after diffusing through the stagnant metal, escapes at the annular metal surface around the tube at a lower constant partial pressure, in this case that of O2 in slowly flowing air, 1 atm.

Jan 1, 1970

By Chester T. Sims

RECENTLY, a new type of superalloy material called TD Nickel* has been marketed.' It is a sim- ple, two-phased alloy, consisting of thoria particles dispersed in nickel of rather high purity (Ni-2 pct Thoz). Its mechanical properties appear relatively superior to previous experimental material attempting to use the oxide nonmetallic dispersion concept (except SAP), and superior to conventional nickel-base alloys at high homologous temperatures. This is derived from an interesting method of creating the dispersion, arising during chemical processing of the nickel and thorium salts in solution while reducing the nickel to metal. An evaluation of the thoria phase was conducted at this laboratory. Material and Procedure. TD Nickel was made available, consisting of several inches of 0.470-in. rod, extruded at a ratio of 64: 1, straightened, and centerless ground. Property determinations on this rod by the supplier at 1800°F showed an ultimate tensile strength of 11,400 psi, yield strength of 9600 psi, and 6 pct elongation. Specimens were removed from the rod for as-extruded metallography, and two 1/2-in. lengths supported on high-purity Al2O9 bricks were placed in a laboratory muffle furnace for exposure at 2000° F. The furnace door was left cracked to allow a slight amount of circulation. One specimen was removed at 200 hr for examination; the other was left for 2000 hr. Metallography. The micro structures obtained for the three conditions of exposure are shown in Fig. 1. Elongation of the grain structure in the extrusion direction is readily evident. The grains appear to be up to 0.001 in. (0.003 cm) long, with a length/width ratio of about 10: 1. Allowing for modest local in-homogeneities in structure, no significant change in thoria particle size or nickel alloy grain size occurred during the 2000°F exposure. However, etching depth varies slightly from one specimen to another, changing the number of particles visible. The thoria dispersion appears to be in the order of 0.01 (min) to 0.5 (max) p diam. The minimum diameter is difficult to estimate at X10,000, and may be less. Interparticle spacing appears to be about 0.1 p. Etching effects can be seen, depending upon grain orientation. A cubic etch-pit pattern appears in certain grains, apparently when etching is started by an anodic particle of thoria, Fig. l(c). The cubic pattern appears related to crystallographic orientation, and is prominent when the [ l00 ] direction is perpendicular to the plane of polish. The grains which present a ridged appearance in the photograph appear to be oriented with the [110} direction perpendicular to the plane of polish. Analysis. The thoria particle size was measured by a line intercept method perpendicular to the extrusion direction. Only particle sizes measuring 0.001 in. at X10,000 or larger could be extimated. Within limits of experimental error, particle size distribution appears to be unaffected by exposure, Fig. 2. To check structural stability further, a grain-growth evaluation was made. The number of grain-boundary intersections was counted at X500 on each of several traces normal to the extrusion direction for each condition. It can be seen from Table I that grain diameter appears unchanged by the 2000°F exposure. The slightly finer grain diameter after 200 hr may be attributed to variations in grain size from area to area in the original extrusion. From the present rather limited study of Ni-2 Th on, it appears that: 1) for time-temperature exposure up to 2000 hr at 2000°F (Larsen-Miller parameter = 57, homologous temperature = 0.8) thoria particles of the size studied are highly thermally stable; they do not significantly react, agglomerate, or diffuse; and

Jan 1, 1963

The Palabora ore consists of two types, a carbonatite containing a low titanium magnetite, and a foskorite containing high titanium magnetite. The latter type also contains substantial quantities of phosphate. These two ore types are separately crushed and are kept separate through copper flotation and magnetic separation, for recovery of magnetite, with the low Ti magnetite being shipped as iron ore. High phosphate tailings are pumped to Foskor, a government-owned phosphate plant nearby. The Palabora plant was originally designed in 1966 for 33, 000 tpd using two 54 in. by 74 in. Allis -Chalmers gyratories; two 7 ft (2. 13 m) standards; four 7 ft shortheads; and six grinding lines, each using one 1,200 hp rod mill and two 1,200 hp ball mills. A fifth short- head and one more grinding line were added later; and with flowsheet improvements, the capacity of the plant was increased to 59, 500 stpd. A further plant expansion involving a third 54 in. primary and two 32 ft by 15 ft (9.75 by 4.6 m) 9,000 hp autogenous mills and another flotation section will bring its capacity to 87,500 stpd in 1977. These two fully autogenous mills are constructed entirely out of doors near the primary crusher, and the ground ore will be pumped a mile to the concentrator by a five-stage pumping system. The Palabora ore is mined with 6, 10, and 12 7d (4.6, 7.6, and 9. 2 cu m) shovels and hauled to the crushers in 110 and 165 st trucks. Sixty-five ton trucks were originally used, but the crusher dump pockets were designed for larger units. Dump pockets, crushers, feeders, and take- away belts are offset in order to keep the two ore types separate. Centerlines of the crushers are only 43 ft (13. 1 m) apart; but, because of their being offset, maintenance room is ample. Initially, more carbonatite ore than foskorite was mined; but as the pit has deepened, this ratio has been reversed. The Palabora ore breaks in the pit with a large amount of oversize boulders; and, with the use of larger trucks, a splitter has been installed on one side of each dump pocket to protect the crusher spider. Smaller trucks dump on the opposite side. To accomodate the splitter, the pocket edge has been raised one meter and moved back one meter. Dust is collected through a special vent shaft between the crushers and the mantle relining area; but even so, two high-pressure water spray headers with nozzles are installed under the edge of the pocket at each dumping position. While only one truck dumps at a time, sprays from all four headers are used to suppress dust. Any leakage of water through the seal around the upper bowl of the crusher is caught by a circular trough under the seal and directed to a sump pump. At this point, there

Jan 1, 1978

"Acta Metallurgical, C E Birchenall, Dec '58 Alfred Noble Joint Prize Committee F B Foley, Dec '61 American Association for the Advancement of Science J T MacKenzie, Dec '58, 0 B J Fraser, Dec '57 American Geological Institute Charles F Park, Oct '58, Arthur Montgomery, Oct '59 Committee on Government Relations American Power Conference J P Weir, T D Hess American Standards Association , Mining Standards Board E R Borcherdt, Jan '59, Otto Herres, '59, J K Richardson, Dec '58, Alternate E W Bullard

Jan 1, 1958

By L. A. Mekler

The recirculating furnace is primarily a heating apparatus of the convection type in which the heat-absorbing surfaces are heated by a mixture of fresh products of combustion and a portion of the combustion gases that have already given off a part of their heat in their previous passage over the heat-absorbing surfaces. In its basic conception, the recirculating furnace can be considered as a closed thermal system in which the heat-absorbing surfaces are constantly swept by a fixed quantity of products of combustion at a given initial temperature with the gases being constantly returned to the furnace and reheated before they again enter the heating zone. Gases equal in amount to those produced by the fuel burned to reheat the circulating gases are constantly ejected from the system to the stack. The recirculating furnace is the most suitable apparatus for heating by convection where low furnace temperatures must be maintained and where only a small portion of the available heat is taken out of the gases, particularly where the maximum allowable furnace temperature is low and where the final temperature of the gases is only a few hundred degrees below their initial temperature. In such cases, recirculation not only provides a method of reducing the rather high combustion temperatures of the fuel when burned without a large amount of excess air, but, by returning to the furnace the heat content of the gases at their final temperature, recovers a large portion of heat that otherwise would have been lost through the stack. The convection-type oil still is particularly suitable for the application of flue-gas recirculation. In an oil still, the heating of the oil is accomplished by applying to the tube surfaces a given quantity of heat of a certain predetermined quality, usually with the initial temperature of the gases not over 1500" F. as measured by thermocouples placed above the tube bank. To obtain the full benefit of the heating surface of the coil, the final temperature of the gases, after passing over the coil, is kept 200" to 300" higher than the temperature of the incoming oil. This final temperature varies from 500" F. for a topping still with only a slight or no

Jan 1, 1928

E. D. WILLIAMSON,* Washington, D. C. (written discussion?).-The paper is interesting and suggestive and the work described should he carried to completion, as it presents points of interest quite apart from the immediate application in glass manufacture. It ought to help, for instance, in throwing light on the chemical nature of glasses and on all questions of viscous flow.

Jan 11, 1919

By R. F. Nielsen, D. E. Menzie

The object of this study was to determine if crude oil could be produced successfully by a process of crude oil vaporization using carbon dioxide repressuring. This process appears to have application to highly fractured formations where the major oil content of the reservoir is contained in the non-fractured porosity with little associated permeability. Crude oil was introduced into the windowed cell and carbon dioxide was charged to the cell at the desired pressure. A vapor space was formed above the oil, and the crude oil-carbon dioxide mixture was allowed to come to equilibrium. The vapor phase was removed and the vaporized oil collected as condensate. Samples of all produced and unproduced fluids were analyzed. Tests were also performed to evaluate the amount of vaporized oil that can he produced by rocking from a high to a lower pressure. The carbon dioxide repressuring process was applied to a sand-filled cell to investigate the performance in a porous medium. A test was performed to evaluate how the condensate recovery changes as the size of the gas cap in contact with the oil changes. INTRODUCTION This study has been directed toward a relatively new process of vaporization of crude oil designed to increase ultimate production of hydrocarbons through the application of carbon dioxide to an oil reservoir. Suggested advantages of carbon dioxide repressuring of a petroleum reservoir are: (1) reduction in viscosity of liquid hydrocarbons due to the solubility of carbon dioxide in crude oil, (2) swelling of the reservoir oil into a larger liquid-oil volume with a resulting increase in production and decrease in residual oil saturation due to an increase in the relative permeability to oil, (3) displacement of more stock-tank oil from the reservoir since the residual liquid is a swelled crude oil, and (4) gasification of some of the hydrocarbons into a carbon dioxide-hydrocarbon vapor mixture. Balanced against these advantages are several detrimental factors which must be evaluated; i.e., high compression costs and corrosion of well equipment and flow lines. Some of the more outstanding contributions to the study of carbon dioxide injection have been reviewed in order to furnish a basis for a continuation of research pertaining to this method. The literature reviewed1-8 has been limited to that dealing with carbon dioxide repressuring processes or with carbon dioxide-crude oil-natural gas phase behavior. Articles relating to carbonated water injection and literature published on the use of low pressure carbon dioxide gas injection in water flooding have not been included in this study. In 1941 Pirson5 suggested the high pressure injection of carbon dioxide into a partially depleted reservoir for the purpose of causing the reservoir oil to vaporize and thus produce the oil as a vapor along with the carbon dioxide gas. By reducing the pressure on this produced mixture of hydrocarbons and carbon dioxide at the surface, it was proposed to separate the hydrocarbons from the carrier gas. He theorized that essentially all the oil in a reservoir could be produced by simply injecting enough carbon dioxide to vaporize the residual oil. This present investigation deals with the vaporization of a crude oil by carbon dioxide, the molecular weight and gravity of the vaporized oil product and the characteristics of the residual oil after several repressuring cycles with carbon dioxide. An attempt is made to evaluate the merits of a vaporization process for the crude oil rather than a flow process where the oil recovery is determined by relative permeability considerations. Such a vaporization of crude oil by carbon dioxide repressuring appears to have possible use in a highly fractured formation where the major oil content of the reservoir is contained in the non-fractured porosity with little permeability. The carbon dioxide flows into the fractures, contacts the crude oil in the matrix and vaporizes part of the crude oil; this vaporized oil is produced and recovered and the carbon dioxide is reinjected again. The specific problem of this study is to attempt to answer this question; Can crude oil be produced successfully (technically, but without economic considerations) from a petroleum reservoir by a process of vaporization of the crude oil by carbon dioxide repressuring? DEFINITION OF TERMS AS APPLIED IN THIS STUDY Carbon Dioxide Contact: One cycle in which carbon dioxide was injected and bled off. Condensate: The hydrocarbon liquid which was condensed out of the mixture of hydrocarbon-carbon dioxide vapor upon reduction of the pressure of the vapor. Hydrocarbons Produced (HCP): All the hydrocarbon!, which were vaporized by the carbon dioxide repressuring process and were removed from the cell during any specific cycle or carbon dioxide contact. Hydrocarbons Unproduced (HCU): All the hydrocarbons which were not vaporized by the carbon dioxide

By A. W. D. Hills

This paper describes the development of a generalized integral-Wofile method for the analysis of heat transfer dwing solidification. The method is extremely flexible, and can be applied to a wide range of situations. This flexibility has been achieved by characterizing the solid metal layer in terms of two parameters, and by developing two simultaneous nonlinear differential equations for these parameters in terms of the heat fluxes crossing the boundaries of the solid layer. The use of these equations is illustrated in a series of examples which involve the solidification of pure metals at zero superheat cooling under different conditions. The simplicity with which the method can be extended to treat more complicated jwoblems is illustrated in a further example which involves natwal convection effects in the liquid metal. ThE rate at which molten metal solidifies in an industrial casting process, and the structure of the cast product, are both controlled by the rate at which heat can be removed from the casting. A knowledge of heat transfer rates is thus essential to the control of the process and to the control of the structure and soundness of the final casting. Heat transfer rates during real solidification processes cannot be predicted by formal mathematical techniques, however, because nonlinear boundary conditions are involved. Approximate methods are normally used, and these have included electrical and hydraulic analogue techniques, finite difference methods, and the integral-profile method. Considerable effort has been devoted to the development of the first two techniques, but the integral-profile method has been used very little so far. This is unfortunate because the method is capable of providing relatively accurate solutions for the heat transfer equation during solidification without involving large amounts of computer time. A further advantage of the method is its flexibility, although this is not apparent from the integral-profile solutions that have been developed to date. These solutions have been derived for the solidification of molten metal at zero super-heat under cooling conditions involving either a constant heat flux from the cooled surface;' a constant heat transfer coefficient at the surface,'-3 or a specified variation in the surface temperature.4,5 A generalized integral-profile method is presented in this paper which can be used to predict unidirectional solidification rates under a very wide range of more realistic cooling conditions. The use of the method is illustrated in a series of problems involving pure metals, or skin forming alloys, solidifying at zero super-heat. However, the principal advantage that this method has over the previous integral-profile methods is the ease with which it can be extended to treat more complicated solidification problems. This is illustrated by considering a problem in which super-heat is liberated from the liquid metal by natural convection during the solidification process. In the final section of the paper the generalized method is compared with previous methods used to predict solidification rates and its extension to more complicated solidification problems is briefly discussed.

Jan 1, 1970

RECENTLY seven Boy Scouts were chosen from all the troops in the United States for their all-around ability, excellence in' scouting, and special ability as writers. Two of the members of this selected group were sons of In-stitute members. In the accompanying illustration, Ber-nard Queneau, son of A. L. J. Queneau, of the U. S. Steel. Corp., can be seen at the extreme left, just behind Theo-dore Roosevelt, who is shaking hands with the boy next to. Carl Zapffe (standing in the middle with his hands behind him), the son of Carl Zapffe, manager of the iron ore prop-erties of the Northern Pacific Railroad.

Jan 6, 1928

LOCAL SECTIONS (There are 60 Local Sections in the United States, 4 Foreign ) ADIRONDACK Established June 18, 1952 Paul W Allen, Chairman William Webb, Vice-Chairman Edwin Briggs, Secretary-Treasurer National Lead Company Mac Intyre Development Tahawus, New York Paul W Allen, Section Delegate R G Fleck, Alternate Section Delegate

Jan 1, 1954

By C. P. Sandberg

C. P. Sandberg, London, Eng. 1 think we should all be grateful to the Pennsylvania Railroad Company, and to their chemist, Dr. Dudley, for spending so much time and money in order to solve an important question; nor are me less indebted to the public spirit which leads them to impart tlie experience thus gained. In Europe nothing similar has hitherto been done, either by a company or by any private individual. In England the great railway companies employ their engineers in other ways, and do not keep a chemist or specialist to study rails; bat even if they did they would probably not publish the results. The chief professional engineers are so occupied with their private practice of railroad construction generally, that they cannot be expected to devote their time and energies to so special a question. The German Railway Union has, in my opinion, missed the real object of its elaborate researches by falling into the error of specifying costly, impracticable tests for rails—tests at the same time which do not infallibly expose the impurities that may be in the rails under examination. There has, therefore, been nothing done on this side of the Atlantic in the way of exhaustive study to determine the best composition for steel rails. America should consequently have full credit for the enlightened example which she has set. I wish, however, to make a few remarks on Dr. Dudley's second paper,—& paper which follows very much upan the same lines of argument as the first red three years ago, upon which I have previously touched in my pabr on the same subject read at the meeting in August last. If Dr. Dudley had discovered a new metal he could hardly, I think, have taken wore pains to prove that he was correct in his first formula for the best chemical colnposition of steel rails. But I hare seen so much done in the way of proof by experiment that I am inclined to think that almost anything can be proved by experiments and by satnples. If Dr. Dudley would only give up his formula, which would not suit any country—not even America—

Jan 1, 1881

By Frederick A. Mumpton

For more than 200 years zeolites have been familiar minerals to geologists and mining engineers as minor, but ubiquitous constituents in vugs and fractures of most basalt and traprock formations. More than 35 different species have been recognized including several, such as chabazite, erionite, mordenite, and faujasite, whose adsorption properties rival those of many synthetic molecular sieves. Igneous occurrences of this type have never been mined on a commercial scale; they are generally small and low grade, and they commonly contain as many as four zeolite minerals, along with small quantities of calcite, quartz, and other silicate minerals. Their economic beneficiation to monomineralic zeolite products has also not been achieved and, for the most part, industrial applications of zeolites have relied primarily on synthetic molecular sieves that were crystallized from hydrous aluminosilicate gels. During the middle 1950s, when Union Carbide Corp. and other groups were developing processes and markets for their fledgling synthetic zeolite businesses, natural zeolites

Jan 1, 1983

Jan 1, 1957

By Frank A. Herald

Through the generous cooperation of the authors of the papers in this chapter, a great wealth of fundamental data is being made available. The same plan of securing and submitting data will be carried forward next year, with the hope of making a nearer approach to complete presentation of the data contemplated in the plan. In order to conserve space, we are printing below such footnotes as have general application to Table 1 in the papers in this chapter: Footnotes to Column Headings Table I In areas where both oil and gas are produced, unless gas is marketed outside the field, such areas are included in column headed "Oil." Manufacture of casinghead gasoline and carbon black is interpreted as outside marketing of gas. Production per acre is determined by dividing into the number of barrels of oil the sum of the number of acres assigned to "Oil" plus such number of acres of the total assigned to "Oil and gas" as represents the portion thereof occupied by oil. Wells producing both oil and gas are classified as "Poducing oil only" unless gas from them is marketed off the lease. W. water; G. gas; A, air. Bottom-hole pressures are preceded by "e." All other figures represent pressures at casinghead with well closed. P, paraffin; A, asphalt; M, mixed. 0 Cam, Cambrian; Ord, Ordovician; Sil, Silurian; Dev, Devonian; Mis, Mississippian; MisL, Lower Mississippian; MisU, Upper Mississippian: Pen. Pennsylvanian; Per. Permian; Tri, Triassic; Jur. Jurassic; CreL, Lower Cretaceous; CreU. Upper Cretaceous; Eoc, Eocene; Olig, Oligocene; Mio. Miocene; Pli. Pliocene. 6, sandstone: SH, sandstone, shaly; Ss, soft sand; H, shale; L, limestone; LS, limestone. sandy; C, chalk; A, anhydrite; D, dolomite; Da. arkosic dolomite; GW, granite wash; P, serpentine. Figures are entered only for fields where the reservoir rock is of pore type. Figures represent, ratio of pore space to total volume of net reservoir rock expressed in per cent. "Par" indicates that the reservoir rock is of pore type but said ratio is not known by the author. "Cav" indicates that the reservoir rock is of cavernous type; "Fis," fissure type. A, anticline; AF, anticline with faulting as important feature; Af, anticline with faulting as minor feature; AM, accumulation due to both anticlinal and monoclinal structure; H, strata are horizontal or near horizontal; MF, monocline-fault; MU, monocline-unconformity; ML, monocline-lens; MC, monocline with accumulation due to change in character of stratum; MI, monocline with accumulation against igneous barrier; MUP, monocline with accumulation due to sealing at outcrop by asphalt; D, dome; Ds, salt dome; T, terrace; TF, terrace with faulting as important feature; N, nose; 9, syncline. Information will be found in text as indicated by symbols: A, name of author, other than above. who has compiled the data on the particular field; C, chemical treatment of wells; G, gas-oil ratios; P, proration; U, unit operation; R, references; W, water; 0. other information.

Jan 1, 1934

NEVADA SECTION J. W. HUTCHINSON, Chairman, FRANCIS CHURCH LINCOLN, Vice-Chairman, HENRY M. RIVES, Secretary-Treasurer, Reno, Nevada W. H. BLACKBURN, E. A. JULIAN, EMMET D. BOYLE, JOHN G. KIRCHEN, FREDERICK BRADSHAW, C. B. LAKENAN, TASKER L. ODDIE. The formation of the Nevada Section was originally suggested by Professor F. C. Lincoln, who had discussed the subject with Mr. William L. Saunders when the latter was President of the Institute. Professor Lincoln sought the assistance of the Nevada Mine Operators' Association, whose Executive Committee constituted itself a Committee on Organization, and authority for the establishment of a Nevada Section to include the entire State was secured from the Board of Directors of the Institute. The formal installation took place at 10 A.M. on May 18, Mr. William L. Saunders officiating. The Honorable Emmet D.. Boyle, Governor of Nevada (and a member of the Nevada Section), made the address of welcome. On the afternoon of the same day, a technical session was held, at which the following papers were presented: History and Development of the Cyanide Process Charles Butters Virginia City Whitman Symmes Ore Deposition at Steamboat Springs Prof. J. C. Jones

Jan 7, 1916

By Walter Kauenhowen

Germany's crude-oil production during 1937 totaled 3,174,157 bbl., an increase of 1.9 per cent over the 3,112,494 bbl. produced in 1936. According to official published data, and using a conversion factor of 1 metric ton = 7 bbl., the oil production of Germany in 1937 by fields was as follows:

Jan 1, 1938

By J. E. Miller, W. E. DeVaney, L. Stroud

During a recent phase study of a natural gas, two stable equilibrium liquid phases were observed at temperatures below —200°F and pressures above 200 psi. This paper reviews the published literature on the occurrence of multiple equilibrium liquid phases and presents analytical data for the vapor and two equilibrium liquid phases of the liquefied natural gas at five experimental conditions. In addition, data for 30 conditions of two-phase equilibria are included. INTRODUCTION The low-temperature phase behavior of gases, most of which contained helium, has been investigated in the laboratories of the Helium Activity for many years. Since 1952, experimental studies of these systems have been continuous as part of the research program at Amarillo, Tex. Because of their value to private industries interested in participating in the Helium Conservation Program, several "Open File" reports containing phase equilibria data for heliurn-bearing natural gases have already been released by the Helium Activity. A paper containing information on the general phase behavior, operating criteria and extensive vapor-liquid data for two helium-containing systems was recently published.2 Additional publications presenting experimental data on the phase relationships of various gas systems are now in process and will be available in the near future. PREVIOUS EXPERIMENTAL WORK Although the formation of multiple liquids has been reported for various systems, to our knowledge this paper is the only substantiated evidence of a vapor-liquid-liquid equilibria in a naturally occurring gas. In 1940, Vink, Ames, and others13 reported the presence of two liquid phases in a hydrocarbon system consisting of mixtures of crude oils, solvents and natural gas. Eilerts and co-workers; published data on the recombined fluids from a gas-condensate well. This condensed gas, containing approximately 76 per cent methane and 24 per cent ethane-plus, exhibited two distinct liquid phases. Weinaug and Bradley 14 observed "unusual" phase behavior in a reservoir mixture. These workers postulated that the anomalous phase behavior was due to the "imminent formation of a second liquid phase". Botkin, Reamer, Sage and Lacey 1 studied two California crude oils that exhibited multiple phases. Kohn and Kuratal0 recently reported two equilibrium liquid phases in the methane-hydrogen sulfide system. Roof and Crawfordl1 and Eakin, et a16 also have reported experiments with binary systems that formed two stable equilibrium liquid phases. APPARATUS AND PROCEDURE A U. S. Bureau of Mines Phase Equilibrium Apparatus was used in conducting this study. The apparatus and procedures employed in its operation have been previously described3 and will not be repeated in detail ill this report. Briefly, the apparatus consists of a windowed cell which can be maintained within ±0.5°F for temperatures between room temperature arid -320°F. Pressure within the cell can be maintained within 0.1 per cent of gauge reading up to 800 psig. Equilibrium vapor and liquid samples are obtained in special containers4 for analysis by a mass spectrometer. Although the accuracy of the analyzer is about ±0.1 mol per cent, the reproducibility of the phase-equilibrium apparatus is considered relatively poor. Values reported from methane and nitrogen are considered accurate to ±l.0 and ±0.6 mol per cent. Data for ethane-plus in the vapor are accurate within 0.2 mol per cent; liquid-phase data for this aggregate compolnent are accurate within 1.5 mol per cent. For helium in the vapor phase, the analytical data are accurate within 0.2 mol per cent; liquid-phase analyses for this component were obtained by the charcoal adsorption method described by Frost8 and are accurate within 0.006 mol per cent. All of these references to the accuracy of reported values are conservative estimates based upon a statistical treatment of reproducibility data obtained with the apparatus.

By Daniel N. Beshers, Ralph H. Condit

An expression for the diffusion coefficient of inlerstitial atoms in the bcc lattice is derived which takes account of jumps between tetrahedral and octahedral interstices. The results are applied to the case of carbon diffusion in iron to find values for jump frequencies of the types, octahedral-tetrahedral, tetra-hedral-tetrahedral, and tetrahedral-octahedral. ThERE has been renewed discussion1-5 concerning the mechanism of diffusion of interstitial atoms in the bcc lattice. This lattice has both octahedral and tetrahedral interstices, and it has been pointed out that the interstitial atoms may make jumps of the octahedral-octahedral type, hereafter called o-o, octahedral-tetrahedral, o-t, and tetrahedral-tetrahedral, t-t. Doubt has been cast on the applicability of snoek's8 model for internal friction to some interstitial migrations in bcc lattices wherein he proposed 0-0 jumps as the principal mechanism of migration. Also, the anomalous excess diffusion of carbon in iron at high temperatures4 has been ascribed to t-t jumps,2,3 even though the sites normally occupied are octahedral. In this paper an expression is derived for the diffusion coefficient, taking account of the three types of jump mentioned. The relationship of the coefficient to the corresponding internal friction relaxation time is found for the limiting case corresponding to Snoek's model. These results are applied to the case of carbon in iron. In Fig. 1, the structure is shown with the locations of the interstices. Each o site has four t site neighbors coplanar with it, and each t site lies halfway between two o sites. There are four t site first neighbors of a t site lying at the vertices of a tetrahedron. Let the average fraction of atoms occupying o sites and t sites be No and Nt, respectively. Since there are six o and twelve t interstices per unit cell having a lattice parameter, a, the concentration of interstitial atoms will It will be assumed that three types of jumps may be distinguished, t — t, t — o, o — t,for which the jump

Jan 1, 1968