Search Documents

By M. P. Nackowski

Geological engineering expanded its role and significance during 1966 in the areas of construction, raw materials exploration and inventory, water supply and pollution, mechanical properties of earth material and regional environmental planning. Efforts varied immensely in scope and magnitude, in simplicity, difficulty and importance. Observations, measurements, and analysis encompassed both simple and sophisticated procedures. CONSTRUCTION Activities in construction ranged from preliminary to detailed evaluations of sites, development of preventative measures and designing corrective measures following construction failures. Most investigations concerned dam sites, highway locations and slope stability, building sites, tunnels and underground storage facilities.

Jan 2, 1967

By J. B. Austin

IN considering so complex a process as the smelting of iron in the blast furnace, there is obviously no single method of calculating efficiency that gives a complete appraisal of the performance of the furnace in all its several functions; such a comprehensive view as is required to evaluate producing ability and manufacturing costs for a given furnace is obtained only by considering a group of efficiencies, each of which measures the performance of the furnace from a specific point of view. For instance, there is the rate of consumption of coke per ton of iron produced, which is probably the most frequently considered, and is certainly one of the most important of the group; there is the efficiency of recovery of iron charged; and there is the efficiency of utilization of energy, both chemical and thermal, in some respects related to the former two yet in other ways independent of either. In each of these cases, the calculation can be made on the basis of the actual input of material or energy, or it may be based . upon a comparison with the minimum amount of material or energy that would be required by a "perfect" furnace; that is, an imaginary ideal furnace analogous to the perfect steam engine used in thermodynamic calculations, when this furnace is operating under optimum conditions. Moreover, the furnace itself can be considered either as an apparatus for smelting iron or, taking a somewhat less common point of view, as a gas producer yielding iron and slag as by-products. Some of these effi-ciencies are more useful than others, yet all are instructive; for a knowl-edge of them not only leads to good engineering practice from the standpoint of control but also discloses limits to possible improvement in performance and indicates the lines along which improvement is most likely to be profitable. Estimates of some of these efficiencies have appeared from time to time in the literature, but many of them are open to objection because they are based on data of uncertain accuracy or because they have been calculated without due regard to the thermo-dynamic principles involved. Moreover, so far as the author is aware, no general survey of the blast furnace comparing its performance in all the aspects mentioned has been made.

Jan 1, 1938

By D. L. Martin

THAT small amounts of impurities have a harm-J- ful effect on the malleability of metals and alloys is well-known. One common type of em-brittlement involves the formation of a small quantity of eutectic at the grain boundaries, and is typified by sulfur embrittlement of nickel. Another example of eutectic embrittlement—sulfur embrittlement of cobalt—is described in this report. In the preparation of specimens for a study of Co-Pt alloys, it was observed that the hot swagabil-ity of the alloys appeared to be influenced by the grade of cobalt used as melting stock. The cause of the hot-shortness was not traced to any particular impurity, although sulfur was suspected.' The damaging action of sulfur on the malleability of cobalt has not been generally recognized,'; in spite of the fact that the Co-S phase diagram8 eveals the same basic conditions—low solubility and eutectic formation—responsible for sulfur embrittlement of iron and nickel.7, 8 Apparently sulfur embrittlement has not been a serious problem in the fabrication of cobalt alloys. One related factor is likely the limited commercial experience with high cobalt alloys, since the predominant use of cobalt has been in alloys containing less than 75 pet Co. A series of Co-S alloys was prepared and studied to establish the effect of sulfur on the hot working characteristics of cobalt. Specimens, 5/8 in. diam by 4 in. long, were prepared by vacuum melting in magnesium oxide crucibles and casting in a copper mold. Two grades of low sulfur electrolytic cobalt were used as the basic material for the study, one from Johnson, Matthey and Co. and the other from the International Nickel Co. Each contained about 99.5 pet Co and had a nominal sulfur content under 0.005 pet. The sulfur was added initially as cobalt sulfide powder. Later, some low sulfur alloys were prepared by diluting the high sulfur alloys with cobalt. Trouble was experienced in controlling the sulfur content. Apparently much of the cobalt sulfide powder was lost during melting, as most of the samples contained a lower sulfur content than was added. The alloys were evaluated for hot brittleness by heating to 1000°C in a hydrogen furnace and swaging in air. The results of these tests are summarized in Table I. All the alloys containing less than 0.008 pet S were successfully hot swaged to 1/4 in. diam. The bars containing more than 0.015 pet S could not be swaged because of the formation of intercrystal-line cracks similar to those illustrated in Fig. 1. Examination of the microstructure of the cast bars revealed cobalt sulfide eutectic at the grain boundaries, Fig. 2. The sulfide was not always continuous at grain boundaries in bars that were hot embrittled but, in general, the particles did form a network that could account for the brittleness above the eutectic temperature, 880°C. There is no question about the brittle nature of a specimen exhibiting a continuous sulfide network such as is shown in Fig. 2b, though a sulfide distribution similar to that in Fig. 2a is marginal. This particular bar cracked when hot-swaged. However, other bars with lower sulfur content but with some sulfide phase at grain boundaries were successfully worked. The reduction of area of a hot tensile test specimen was also found to be a sensitive indicator of sulfur embrittlement. The variation of reduction of area with sulfur content is shown in Fig. 3 for specimens fractured at 900°C in an evacuated capsule. The ductility of cobalt is greatly reduced when the sulfur content exceeds 0.005 pet. Similar results were obtained for alloys tested at 800°C, below the eutectic temperature. The upper sulfur embrittlement limit of 0.015 pet, Table I, agrees with the observation of Kalmus8 hat

Jan 1, 1957

ARIZONA Established July 10, 1915 ROBERT W. THOMAS. Chairman ROBERT W. HUGHES, Vice-Chairman HUBERT O. WOODS. Secretary-Treasurer American Smelting & Refining CO., Hayden, Ariz. FRANK A. WARDLAW, JR., National Director THEODORE BROOKS I H. C. HENBIE THOMAS C. CHAPMAN P. D. I. HONEYMAN CARL H. COLE JOHN E. LANNING JOHN H. DAVIS ALBERT MENDELSOHN EDWARD G. DENTZER BRENT N. RICKARD MORRIS G. FOWLER F. A. WARDLAW, JR.

Jan 1, 1942

By P. S. Rudman

The solubility limit and the diffusivity of carbon in molybdenum have been obtained by duffising carbon into molybdenum rods from a Mo + Mo2C powder mixture. The solubility limit was taken as the long-time asymptotic limit of the rod composition. The diffusiv-ity was obtained from fractionally saturated rods from the rate of change of the average composition. Compositions were determined by chemical analysis. The solubility limit obtained is: WhILE the Mo-C system is important in refractory alloy technology neither the solubility limit nor the diffusivity of carbon in molybdenum is unambiguously known. In Fig. 1 the Mo-C phase diagram is presented. The heavy lines, the terminal solution solubility limit, and the eutectic temperature are results of the present investigation and will be discussed in detail later. However, it is readily seen that the previously published solubility limit determinations, Few and Manning1 and Fromm and ROy2 differ by up to an order of magnitude. The general form of Fig. 1, the Mo2C field, and a eu- tectic temperature -2200°C are due to an early Investigation by Sykes et a1.3 Although they did not determine the solubility limit, they did establish that the maximum at the eutectic temperature was about 1000 ppm. The only other prior data found on the solubility limit is from a lattice-parameter study by Speiser et a1 .,4 from which it can be concluded that the maximum solubility is greater than 1800 ppm. There does not appear to be any data oh the diffusivity of carbon in molybdenum. However, Samsonov and Epik5 have determined, from the rate of growth of an MozC layer, the diffusivity of carbon in Mo2C, and this has been erroneously interpreted, for example by ~c~eil,' as applicable to diffusion of carbon in molybdenum.

Jan 1, 1968

By W. A. Backofen, F. de Kazinczy

FRACTURING under conditions of particular interest is identified with the junction of curves relating tensile yield and fracture stresses to test temperature; the intersection point gives the lowest stress, for brittle fracture (at the ductility transition temperature). An expression for is found in Cottrell's brittle-fracture analysis, Eq. [15],1 while measurements of this stress and temperature have been reported for a low-carbon steel heat treated to differ-

Jan 1, 1962

New York LOUIS D. HUNTOON, Chairman. ARTHUR S. DWIGHT, Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. E. MALTBY SHIPP, Treasurer. GEORGE F. KUNZ, W. De L. BENEDICT. Boston ROBERT H. RICHARDS, Chairman. ALBERT SAUVEUR, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston. Mass. TIMOTHY W. SPRAGUE, HENRY A. WENTWORTH.

Jan 1, 1917

By J. G. Montgomery

An increased drilling activity was apparent in the shallow sand fields of northwestern Pennsylvania during the year. This drilling, however, was confined to previously outlined productive areas and as new shallow sand pools of interest were discovered. Drilling for Oriskany gas proceeded at about the same rate as in previous years. One new area in Kinzua township, Warren County, was opened up during the year by a producing well, but later this well developed salt water and the productive capacities of the area are very indefinite at the present time. Production from the shallow sand areas remained approximately the same as in 1935. Production from the Oriskany or deep sand areas increased approximately 20 per cent. Two new markets were made available for the Oriskany gas during the closing months of the year by the completion of the Peoples Natural Gas Co. line from the Hebron field to Clarion County, Pa. and Penn York Gas Co. line from the Harrison field to points in northwestern New York State. With the exception of the Kinzua well, the few deep wildcat wells drilled during the year failed to discover new fields in the deep sands. Bradford Oil Field The accompanying data on the Bradford oil field include only the production obtained from the portion of that field that is in the State of Pennsylvania, for it appears probable that Cattaraugus County production, which consists mainly of the New York State portion of the Bradford field, will be included in annual oil production figures for New York State. The Bradford field production for 1936 totaled 14,533,000 bbl., and as it is necessary to estimate New York State production for the Bradford field, the accompanying data includes the production from the Pennsylvania end of the Bradford field of 13,208,000 bbl., which is an increase of approximately 8 per cent over 1935 production.

Jan 1, 1937

Jan 1, 1969

By T. A. Read, S. W. Kitchen, H. I. Fusfeld

At the present time most artillery cartridge cases are used only a single time. Since the process of reshaping a fired cartridge case so that it may be used again is much simpler and cheaper than the original manufacture of the case, it is clear that important savings could be effected if such re-formed cases were used in place of new cases. Extensive use of reconditioned cases has been hindered in the past, however, by the deterioration of the brass which may occur in the period of time between the first firing and the reconditioning of the cartridge cases. This deterioration sometimes results in a dangerously high incidence of firing splits in groups of reconditioned cartridge cases. It appears that the mechanism of the deterioration is the season cracking of the brass, for season cracks, of varying degrees of severity, may frequently be found in the cartridge cases after their return from the field. There are, of course, severe practical limitations to the extent to which fired cartridge cases can be protected from corrosion under battle conditions, particularly since the powder residue in the case is itself corrosive. The present paper describes a rapid method of testing the sidewalls of artillery cartridge cases for the presence of season cracks. This method has been developed specifically for use in connection with the reconditioning of fired cases, and makes it possible to carry out 100 per cent inspection. This new method of inspecting cartridge

Jan 1, 1945

By Luis Emylnn Salas

If the ordinary wet method be attempted for silver-bullion containing tin, much trouble is experienced, varying with the amount of tin present. Even with a percentage as low as 0.05, the end-point is masked by a persistent turbidity, while with amounts ranging from 0.5 per cent. upward, the determination of the exact end-point is impossible, owing to the finely divided or colloidal metastannic acid resisting all efforts to cause it to settle, or to give a clear supernatant liquid. The object of the following experiments was to seek a remedy for these difficulties, and to find the conditions whereby the Gay Lussac method might be applied directly to these bullions. Material containing tin is met with frequently in bullion from Mexico or Bolivia; and tin is carried (sometimes in large quantities) in jewelers' sweeps. 1. A bullion was prepared containing Ag, 74; Cu, 25; and Sn, 1 per cent. A weighed amount was treated by the humid assay-method as if it were an ordinary bullion free from tin. Ten cc. of HNO, (1.21) was added, and the bottle was heated until all traces of

Jan 1, 1913

By W. Spencer Hutchinson

THE outstanding engineering accomplishment of the last three decades has been the development and application of more and cheaper power and its use instead of the labor of men and animals. Substitution of power for manual labor has taken effect on every hand in the United States. With the aid of energy mechanically available to his hand, one man does the work that only a few years ago required two, three or even a greater number of laborers. The results in respect to the favorable economic effects are well known; namely, increased production, higher wages and lower costs. On the other hand, the vast social effects, both good and bad, have been none the less important, even if less understood and only casually regarded. The chief sources of energy today are the mineral fuels, coal and petroleum. In the United States they yield more than 90 per cent of the total energy demand. Thirty years ago the proportion of energy supplied by the mineral fuels was likewise above 90 per cent, but the division according to origin was very different. These relations. are shown for the years 1900, 1930 and 1950 in Table 1.

Jan 1, 1933

By R. S. Kinasevich, D. D. Crabtree, D. W. Fuerstenau, T. P. Meloy, A. L. Mular

This paper presents details of the concept that size reduction in comminution machines takes place by three mechanisms; namely impact, abrasion, and chipping grinding. Experimental evidence is presented to show that each of these comminution mechanisms produces particles of a characteristic size distribution. The actual product from a comminution device has been postulated to be the result of a composite of these three types of mechanisms. Composite curves are demonstrated for a material following the Gaudin-Schuhmann, Gaudin-Meloy, and Rosin-Rammler size distributions. About forty years ago, Gaudin1 showed that grinding may be considered a combination of impact and attrition. Since that time, major efforts have been devoted to studies, both experimental and theoretical, of impact and compression fracture, while attrition has been almost wholly neglected, at least quantitatively. A significant attempt to distinguish between attrition and impact grinding is the work of Tanaka2 in Japan. By means of an instrumented abrasion grinder and a drop weight device, he determined coefficients relating the increase in surface area of various materials to the energy expended by the two methods of comminution. He showed that physical properties of a material determine its response to attrition and impact grinding. By extending his ideas to ball milling, he concluded that to a large extent the basic comminution process in a ball mill is due to the impact of falling media. Because Tanaka used a mass of particles in his drop weight device, however, he did not obtain pure impact size reduction. The purpose of this paper is to define basic mechanisms of size reduction, to verify that each has a characteristic and meaningful distribution curve, and to show how a combination of these mechanisms results in a size distribution very like that produced by grinding mills. DEFINITION OF COMMINUTION MECHANISMS The product from a grinding device will be considered to be the sum of the contributions resulting from the action of three basic mechanisms of size reduction which operate in a ball and rod mill. These are impact grinding and two forms of attrition, namely abrasion grinding and chipping grinding. Each is defined below. Impact Grinding: If a straight line is obtained when the cumulative weight fraction finer than a given size is plotted on log-log paper as a function of that size, the slope of the line is defined as the distribution modulus. A number of investigators 3,4,5 have shown that impact fracture of single specimens of different composition and shape results in a distribution of daughter particles that exhibit a distribution modulus of unity. This has also been true for materials broken in slow compression. Moreover, under slow compression or impact fracture conditions, theoretical distribution equations6*' which approximate the Gaudin-Schuhmann distribution when the distribution modulus is close to unity agree reasonably well with the experimentally obtained products. If one now considers a comminution process where many impact or compression fracture events are taking place, then any rational summation of the individual events yields, in the finer size range, a Gaudin-Schuhmann distribution whose distribution modulus is also unity. If the size distribution of the product from a mill has a distribution modulus of unity, it is implied that particles are fractured in a manner which results in a comminution event having a distribution like that obtained for the breakage of single specimens. These impact events would occur when a particle is smashed between balls or between a ball and the mill liner. Attrition, on the other hand, is that form of grinding which cannot be called impact grinding, and comprises both abrasion and chipping grinding. Abrasion Grinding: Abrasion is a form of surface wear resulting when particles rub against each other or against balls or the mill liner of a tumbling mill, somewhat like a piece of wood being rubbed over a piece of sandpaper. The surface wears at a more or

Jan 1, 1964

By H. H. Rachford, J. Douglas, D. W. Peaceman

A numerical solution of equations describing two-phase flow in porous media shows promise in providing a technique for predicting the displacermet from satlds of oil by water or gas. The description includes the influence of relative permeability, fluid viscosities and densities, graviry, and capillary pressure, and, tholrgh tested ortly for two-dimensional cases, should be eqlmlly applicable in three-dimensional geometry. Two memorical methods ore presented: the first method is quite general in its applicability; the second method can be used only with certain types of boundary conditions but requires less computing. Comparisons of computed results with data from Inhoratory models are presented. These data were taken on a water flood of a strarified model and on water floods of a five-spot model for favorable and unfavorable mobility ratios. On the stratified model, excellent agreement with recovery at breakthrough was obtained; agreement with recovery after breakthrough was poor. In the five-spot model, good agreement was obtainecl with recovery at and after breakthrough. The purpose of this paper is twofold: first, to present a reservoir engineering method requiring knowledge only of rock geometry and the normally measured rock and fluid properties for calculating the multi-dimensional flow of water displacing oil from porous, water-wet rock containing connate water; and, second, to investigate the validity of the method by comparing results of calculations with previously observed displacements in laboratory models. The availability of such a verified technique of reservoir analysis would afford major advantages. First, it would demonstrate that the fundamental macroscopic concepts of two-phase fluid mechanics, i.e., relative permeability and capillary pressure, yield an adequate description of the physical process. Also, since most reservoir rocks appear to be water-wet and contain connate water along with oil, it would provide a method of technical and economic value for calculating the course of oil displacement by water directly from measured reservoir and fluid properties. It is important to emphasize that the calculation is subject only to the limitations of detail and precision of reservoir information, but not to limitations introduced by simplifying assumptions. Further, it would providc almost the only means of examining the influence of factors such as the size and extent of reservoir inhomogeneities and uncertainties in the basic reservoir data. Knowledge of this influence is essential in stating quantitatively the detail required to define a reservoir and in establishing the relation between the uncertainty in the definition of reservoir properties and the reliability of predicted performance. Moreover, in the process of solving a particular problem much detailed information would become available about the displacement process. For example, at each point in the reservoir for all stages of the displace ment. the calculations would yield not only the water and oil saturations but also the direction and magnitude of fluid velocities and the local fluid mobilities. Such dctail is potentially of great value in giving insight into the mechanics of particular displacements. The development of such a method has long been the goal of research in the application of numerical an-alysis to petroleum reservoir enginecrinz. The most complete treatment of the displacement process published to date is that of Douglas. Blair, and Wagner,' which, however, was limited to flow in a single dimension. The method presented in the present work is hascd on the numerical solution of a finite difference analogue of the multi-dimensional differential system describing the displacement process. Although current work has considered only displacement of oil by water from water-wet sands, the differential system for other immiscible displacements, such as gas displacing oil with which it is in phase equilibrium, is quite similar. It should therefore be expected that the technique described will be applicable to displacement by gas as well. The description of the simultaneous flow of fluids through porous media in terms of relative perrncability and capillary pressure has been adequately discussed in the literature and standard textbooks. Sec, for exampje, Muskat. Chapter VII.'

By J. Nagy, D. W. Mitchell, E. M. Murphy

In 1957 research was initiated in the U.S. Bureau of Mines experimental coal mine near Pittsburgh, Pa., to study factors affecting foam generation and transport, to evaluate the effectiveness of high-expansion foam for controlling mine fires, and to develop techniques for applying the method under U.S. mining conditions. These investigations showed that high-expansion foam containing at least 0.2 oz of water per cu ft of foam is effective in controlling experimental underground fires burning coal, wood, and oil. Sometimes the fire was completely extinguished, but more often, it was brought under sufficient control to permit either a direct attack on the fire with a stream of water or loading of the hot material into cars. A progress report' prepared in July 1958 summarized the initial achievements of the USBM experiments. Since then other phases of the foam-plug method for attacking fires have been studied in the laboratory and in the mine. Previous studies by British engineers' of the foam-plug method for fighting mine fires indicated that high-expansion foam was effective in controlling experimental timber fires in an underground passageway. Their subsequent workx-1 pertained to the practical aspects of fighting large fires within a mining area with a foam-plug. CONTROLLING EXPERIMENTAL FIRES In the USBM tests foam was formed by spraying a dilute solution of a foaming agent on a metal or cotton net of 1/8 to 1/4-in. mesh. Air passing through the continuously wetted net forms bubbles of 1/2 to 11/2-in. diam and produces a honeycomb of foam that fills the passageway. Under the ventilating-air pressure, this light-weight plug moves forward through the passageways, around sharp corners, and over obstacles. as illustrated in Fig. 1. High-expansion foam was transported to a wood fire, an oil fire, and 13 coal fires. Figs. 3 and 4 show a typical coal fire before and after attack with foam. In 12 of the 15 experiments the fire was brought under control when the water content of foam was 0.2 oz or more per cu ft. A fire was considered controlled when the flames were quenched and observers could cross the area without wearing breathing apparatus or protective clothing. In the other three experiments, conducted when the water content was less than 0.2 oz per cu ft of foam, the flames were retarded but the fire was not controlled. Coal fires have been attacked successfully by foam introduced at points varying from 155 to 1010 ft from the fire. The time of burning in coal beds 10 in. thick ranged from 11/2 to 5 hrs or more. Most of the experimental fire beds were 15 ft in length. However, in one experiment a floor fire 25 ft long and 5 ft wide was constructed $5 upwind from another fire 15 ft in length; in another instance, the fire was 100 ft long and 5 ft wide. Foam was applied to the fires for periods ranging from 7 to 36 min. The time required for foam application depends on the extent of the fire, time of burning, water content of foam, foam velocity, and degree of fire control desired. In addition to the coal fires, foam was transported to a fire covering 45 sq ft, produced by 15 gal of oil burning in metal trays on the floor. The foam extinguished the oil fire in about 1 min. In one other test, the burning of 1100 lb of dry sawmill slabs stacked in open cribs 4 ft high and 16 ft long was brought under control by foam in 2 min. Composition of Gases in Return Air: In several of the experiments samples of the return air from fire zones were collected; composition of the atmosphere before, during, and after foam application was then determined. Because of condensation in the relatively cool sampling tube, the amount of water vapor was not determined. Analyses showed that concentration of carbon dioxide and combustible gases increased as the foam began passing over the fire. This resulted from the decrease in the volume of air when foam generation started and from the formation of gases when water reached the fire.* The quantity of gases generated would not be greater than that from an equivalent amount of water applied directly to the fire. The highest total concentration of combustibles (CO, CH1, and H2 mixture) obtained during the experiment was about 2 pct; this occurred 6 min after foam reached the fire. This atmosphere was nonex-plosive, but calculations show that if the air flow were reduced to about 5 fpm and if the rate of gas liberation from the fire remained constant, the mixture would be explosive. The use of foam on a fire in all probability would affect the normal ventilation of a mine. If the mine is gassy, this factor must be carefully considered before the foam is applied. APPLICATION OF THE FOAM-PLUG TECHNIQUE IN MINES Equipment and procedures for applying the foam-plug methods must be adapted to the prevailing conditions at a particular mine. Some factors to be considered in developing equipment are: size or extent of the mine, dimensions and number of entries, ventilation system, mining methods, haulage facilities, availability of water, amount of methane liberated, and existing fire-control apparatus. • In most experiments the initial air velocity of 200 fpm decreased to 50 to 100 fpm as the foam plug increased In length.

Jan 1, 1961

By Frederic Carter

THE gold, silver, copper alloys have been the subject of several fairly complete investigations by Jänecke, Sterner-Rainer1 and others, and indeed it would seem as if almost too much labor had been expended on them when one thinks of the numerous other ternary alloys calling for more light; however, the combinations of the three metals are actually so widely used in jewelry that they merit perhaps the work done on them. There are a few properties of importance and interest not treated by the authors mentioned which the writer investigated some little time ago, and therefore he has ventured to put on record the results of some of his tests made at that time. He has chosen, as being the two series of most importance to the jeweler, only the 14 and 18-kt. golds, so the subject is by no means so inclusive as that previously treated. As stated, this paper is merely a record of tests made in a practical manner on two useful series of alloys, and is not at all a critical study of their properties. 14-KARAT ALLOYS These alloys are important because they are the most generally used in 14-kt. jewelry; by changing the proportions of silver and copper there are obtained all shades of color from the green of the alloy containing gold and silver but no copper, to the red of the alloy containing gold and copper but no silver. Many 14-kt. gold alloys are made with the addition of zinc to the three metals mentioned here; the added metal does not appreciably alter the color of the alloy nor has it, in general, much effect on the working properties; it may, however, prove useful as part of the zinc added may act as a deoxidizer and render the alloy free of gas. It is not a necessary addition because with proper precautions all the 14-kt. gold alloys containing only silver and copper in addition to the gold can be made free of gas and capable of being cold rolled without cracking. The alloys in which approximately equal quantities of silver and-copper

Jan 1, 1928

By C. C. Harris Discussion by B. K. Loveday

B. K. Loveday (National Institute for Metallurgy, Johannesburg, Republic of South Africa) - The paper and subsequent technical note' describing a method of determining the parameters of the three-parameter size-distribution equation developed in the paper were read with much interest. This equation was also used at National Institute for Metallurgy (NIM) to describe size distributions in grinding tests, because it was necessary to have a single equation to describe the size distribution at any time during a test. A graphical method also was used to determine the three parameters, and the use of this method as an alternative to Professor Harris's latest method is discussed here. The three-parameter model can be expressed as follows: Eq. 1 can be rearranged and transformed to Yield a linear reiationship between Y and X (transformed) log

Jan 1, 1970

By John H. Hollomon

THE interpretation of notched-bar impact results has been a matter of controversy since the introduction of more or less standard tests by Fremont,1 Charpy2 and others at the turn of the century. Many investigators3-l1 have contributed to the understanding of the significance of such tests. Several symposiums12,13 have been held with the express purpose of discussing the significance and interpretation of the impact tests. It is not the purpose of this paper to review all these contributions to the development of the knowledge on this subject, but rather to present an interpretation of notched-bar impact tests that appears to be in agreement with the available published data. Fundamentally, the interpretation discussed in this DaDer of the brittle failure of some steels in notched-bar impact test is similar to the qualitative analysis presented by Ludwik3 in the 1920's. Essentially, Ludwik stated that the function of the notch was to increase the tensile stress necessary for yielding, and that brittle failure occurred when the stress necessary for yielding exceeded the normal stress required for fracture (with no plastic de- formation). Ludwik, however, had no means of measuring this normal stress necessary for failure of a plastically* undeformed metal, therefore he could not extend his interpretation beyond the qualitative stage. Kuntze14 and recently MC- Adam15 attempted to determine the effect of deformation on the stress necessary for fracture by testing, in tension, specimens notched to various depths and angles. Because of the uncertainties in Kuntze's (and RlcAdam's) analysis of the stresses (which have been pointed out by SachsI6) and the inherent nonuniformity in the stress distribution in notched bars, the results of such investigations are difficult to interpret. A more direct method of measuring the effect of deformation on the fracture stress was suggested in previous papers17-l8 and has been utilized in the present investigation. The present paper concerns itself primarily with the behavior of notched impact specimens. The effects of strain rate, temperature, and stress distribution, which are discussed with reference to the impact specimen, apply just as well to the behavior of metal at the bases of notches in any engineering structure. All that is necessary is to determine the stress distribution in the structure at the base of the notches.

Jan 1, 1944

By Kalanadh V. S. Sastry, D. W. Fuerstenau

A locked-cycle balling procedure has been designed to simulate continuous, closed- circuit balling drum operation in the laboratory. By this method, it is possible to simulate the surging in green-ball production rate and circulating load that is experienced in industrial balling circuits. Through an investigation of the effect of feed rate on the stability of the locked-cycle, balling process, it was found that higher feed rates lead to increasing instability in the process. An analysis of the experimental ,results is presented and the utility of the locked-cycle experimental technique for evaluating the stability of an industrial balling drum operation is discussed.

Jan 1, 1976

By J. W. Spretnak, G. W. King

THE crystallography and morphology of 0-Al,Fe precipitates in an A1 + 0.5 wt pct Fe alloy have been studied by transmission electron microscopy. The alloy was cast in cylindrical ingots, 15 cm in diameter and 60 cm in length, and cooled slowly. The measured composition was 0.527 wt pct Fe, 0.001 wt pct Mg, and 0.003 wt pct Cu. Spectrographic analysis revealed no additional trace impurities. Thin slices were cut from the ingot and reduced by more than 95 pct by rolling to a thickness of 0.1 mm with no intermediate annealing treatments. These thin sheets were then vacuum-annealed for 1 hr at 612°C and air-cooled in their capsules. Thin foils for examination in the electron microscope were prepared by electropolishing. The precipitate is found in the form of oval platelets on the (110) planes of the matrix. The major axes of the platelets are parallel to the (110) directions of the matrix, and vary in length from 1/2 to 2 p. The thickness is about 1/10 p. Examples of platelets, both in the plane of the foil and normal to the foil, are shown in Figs. l(a) and l(b), respectively. lack' found that ?-A13Fe (more correctly All13Fe4) belongs to the monoclinic system. Using Black's structural data and simultaneous electron-diffraction patterns from the matrix and precipitates, the habit planes and directions were determined to be: (00l)? || (110)Al [100]? || [001]Al The orthogonal crystallographic axes of the precipitates are accurately in the habit plane, while the measured coincidences of the directions are only within 10 deg. The major axis of the platelet is parallel to [010] in the 0. This orientation corresponds to the direction of nearest registry of the lattices.

Jan 1, 1964