Search Documents

A new Military, Engineering School has been established at Camp A. A. Humphreys, Virginia. This camp was used throughout the summer and fall of 1918 for the Engineering Officers Training School in preparing engineer officers for the United States Army. The camp and the courses prescribed were laid out on an ambitious scheme, which since the armistice has been signed, have been directed wholly, toward the permanent establishment of an Engineering Training School for Officers of the regular Army. Those young officers who were graduated from Nest Point at the end of a two-year course, necessitated by the emergency, have been ordered to Camp Humphreys to complete their engineering education.

Jan 3, 1919

By Max Littlefield, Godbold A. C., Gray L. L.

The West Edmond pool of Central Oklahoma, a limestone reservoir, has an area in excess of 29,000 acres and as of Sept. 15, 1946, had produced 53 million barrels of oil from 731 wells at an average depth of 6900 ft. Water has encroached into the reservoir along the west side of the pool and although the area of water invasion is large the net volume of water influx is small, because encroachment has been primarily into a fracture system. The most significant part of this study concerns the character of the Hunton reservoir. Geological study of cores of the producing section was made to supplement core-analysis data. It was determined that approximately 90 pct of the pore volume was contained in intergranular or sand-like porosity and 10 pct in fractures (intermediate porosity). The porous limestone is divided into blocks by the fractures, although in the strongly dolomitic parts of the producing section, fractures are less well developed. The low-permeability intergranular porosity, largely subsidiary to the high-permeability fractures, will produce oil into the fractures by evolution of solution gas. The fractures in effect serve as drainage channels for production of oil from the inter-granular porosity. Because of such a large difference in permeabilities of the two com-ponents, a high degree of by-passing will occur, and, accordingly, the economics involved in undertaking full-scale high pressure gas injection operations have been seriously questioned. Introduction The West Edmond Hunton pool, which covers portions of Canadian, Logan, Oklahoma, and Kingfisher Counties in Central Oklahoma, is the largest reservoir producing oil from a limestone in the state. The total area of the pool comprises about 29,240 acres and development is considered to be essentially complete. In all, 731 producing wells have been completed in the Hunton reservoir at an average depth of approximately 6900 ft, and have yielded a cumulative oil production in excess of 53 million barrels as of Sept. 15, 1946. In addition to wells completed in the Hunton limestone, 21 wells have been completed in the Bartlesville sand at a depth of approximately 6500 ft, which have produced a total of 730,000 bbl of oil. One small producer has been completed in the Cleveland sand at a depth of 5700 ft. However, a study of only the Hunton limestone reservoir will be presented in this paper. The most significant phase of this study concerns the special type of geological core examination that was made in an effort to ascertain the type and degree of porosity in the rock in accordance with lithologic types. Results of this geological study showed the west Edmond pool to be of such a complex nature as to appreciably affect the behavior normally associated with homogeneous reservoirs. Recognition of this condition in the

Jan 1, 1948

By W. D. Robertson

The effect of a tensile stress in accelerating the corrosion-cracking of certain alloys of aluminum, magnesium and iron is widely recognized. The literature is extensive and it is only necessary to cite the recent ASTM—AIME Symposium,l There are, however, no experimental data conclusively showing the effect of an applied compres-sive stress. It has been inferred, from the generally accepted mechanism postulated for the acceleration of corrosion by an applied tensile stress, that a compressive stress would inhibit corrosion. Furthermore, it is observed that corrosion cracks invariably start on the tension side of a specimen bent as a simple beam. This observation has led to the suggestion that shot-peening of the surface would inhibit or eliminate stress-corrosion cracking in magnesium alloys and aluminum alloys. However, the degree of inhibition produced by shot-peening does not appear in the literature except for the above qualitative references which are unsupported by experimental data. Moreover, while peening undoubtedly imposes a surface compressive stress, the alteration of the surface by the severe cold-working involved complicates the interpretation of the results with respect to the effect of a compressive stress alone. If corrosion proceeds along preferential paths produced by precipitation from solid solution, it is easily understood how a component of tensile stress normal to these paths will accelerate the corrosion and lead to ultimate failure. On the other hand, if the metallurgical conditions are such as to create preferential corrosion paths, then it is difficult to understand how a compressive Stress, produced by shot-~eening Or any other method, can inhibit corrosion except in the sense that the accelerating factor is removed. Thus, if the basic corrosion mechanism remains unaltered, there should be little or no inhibition resulting from the application of a compressive stress if inhibition is defined as the reduction of the degree of corrosion below that experienced in the unstressed state. The experiment described below was performed to isolate and evaluate the effect of a compressive stress on the corrosion and stress-corrosion cracking of a high strength aluminum alloy (24-S); and, by a Comparison of the corrosion rate of 'pecimens subjected to an applied tensile stress, compressive stress and in the unstressed state, to clarify the role of stress in intergranular corrosion. Experimental Procedure The experiment was conducted with the aluminum-copper-magnesium alloy known as Duralumin 24-S.* Specimens, 0.064-in. thick, in the form of I-in. wide strips sheared parallel to the rolling direction,

Jan 1, 1949

By J. C. Bayles

Jan 1, 1885

By Ernest R. Darby

WHEN bronze is melted in open-flame furnaces a considerable amount of slag is formed during the melting operation. This slag maybe incidental to the melting practice or it may be formed intentionally by slag-forming constituents added to the furnace charge to provide a covering for the melted metal. When this slag is removed from the furnace, it contains, in addition to the free metal carried with it by the skimming operation, a considerable amount of metal as oxide either combined or mechanically mixed with it. By the usual crushing and washing methods this metallic oxide generally goes to the tailings pile, so diluted by other foundry waste that its recovery is economically impossible. If this furnace slag is not mixed with other foundry waste, practically all of the metal oxide as well as the free metal may be recovered by some form of smelting operation. The first side of the problem to be considered is the amount of slag produced. It may not be true that the majority of foundries have no record of the amount of slag made, but it is certainly true that a very great many either have no record or pay little attention to it. Usually the collection of furnace slag for one normal week's run will be sufficient to determine the advisability of its being handled in a different manner from the crushing and concentrating generally employed. If a large representative sample of the accumulation is crushed and concentrated and the recovery compared with the results of a careful assay, it will be found that a large percentage of the total metal content was lost in the washing process. The percentage of loss will be greater than the metallic oxide content, as some free metal in extremely fine particles always is carried away in grains of slag. From such a comparison, it may be determined whether or not the slag should be melted, sold or treated as before. An example of an actual test of this kind is given below. In a foundry melting 50,000 to 80,000 lb. of bronze per day, a week's accumulation of furnace slag and ladle skimmings amounted to 16,500 lb.-over three times as much as the foundry superintendent estimated before the accumulation was made. Two tons of this material was taken as representative of the lot. This was ground through a thoroughly cleaned ball-mill and concentrated over a Wilfley table. The

Jan 1, 1928

By Earl C. Herkenhoff

Publication of the article "The Flotation Behavior of Digested Asphalt Ridge Tar Sands" by R.J. Smith and J.D. Miller has confirmed and again spotlighted a most significant and important development in the field of tar sand and heavy oil mining. This is the ability to recover 95% of the bitumen in dry tar sands by a hot water process. The initial investigation by Miller and Sepulveda in early 1978. "Separation of Bitumen from Dry Tar Sands," was the first blockbuster. It is disappointing that there has been so little scientific and industry ackowledgement that the authors laid to rest the long entrenched belief that the sand grains had to be "water wetted" for a hot water process to be applicable. Dr. Miller and his researchers at the University of Utah used slightly different mineral dressing terminology in describing their process but it is essentially the old, established technique of high &lids attrition scrubbing at elevated temperatures with a conditioner or modifier, followed by dilution and froth flotation. Similar techniques were described in detail for other nonmetallic minerals in the mid-1940s by Stuart Falconer of American Cyanamid Co. The authors used a 15-minute "scrub" period (or in their terminology "digester step") at 73% solids and 95OC (203°F) in a 0.3 m solution of sodium carbonate-about 4 kg/t (8 lb per st) of tar sand. Flotation was at 10% solids. Obviously, the scrub is an expensive step with respect to energy input but the high recovery of bitumen appears to justify it. Two basic questions then arise: What are the effects of shorter scrubbing time, lower temperature, and less sodium carbonate? Would a two-stage approach be advantageous? That is, could you get the major proportion of the bitumen with a mild scrub and apply the high power and temperature only to the refractory portion? These variables should be evaluated. Apparently, all results were only for rougher flotation. What would the grade and recovery of bitumen be if multiple cleaner flotation steps were employed? We must concede that a 60.62% grade of bitumen leaves considerable room for upgrading. Finally, it should be noted by all executives who approve funds for heavy oil recovery schemes, most of which are variations of in-situ methods, that mining can yield a 95% recovery of bitumen. That is correct, 95%. Imagine what that does to the total barrels recovered from a heavy oil resource compared with the scrawny 30-35% maximum recovery we are getting now. The conclusion-let's mine heavy oil and tar sands.

Jan 1, 1983

The Library of the above-named Societies is open from 9 A.M. to 10 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by forwarding copies, of mining reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 11, 1915

By B. N. Das, P. A. Beck

THE o phases have a complex tetragonal structure with Lo/ao = 0.52 and 30 atoms per unit cell.1 A large number of such phases are now known to occur in various binary systems of the transition elements and they exhibit the following typical features: 2,3 The composition of binary o phases is variable, ranging from approximately A4B to ABI. With only a few exceptions, in the o phases the A-ele-ment comes from the V- or Cr- group of the periodic table, while the B-elements are from the Mn-, Fe-, Co-, or Ni- group. In the first long period the corresponding o phases of the V- and Cr-series have approximately the same compositions. However, as the B-element changes from Mn to Fe to Co to Ni, the mean composition shifts monotonously toward higher A-contents.2-4 For example, if the mean compositions of the various o phases with vanadium are compared with each other, the composition shift mentioned above becomes plainly visible: V 30Mn0 80 Vo.45Feo..,, Vo .,Coo. 45 and Vo.5Nio.3. Similiar composition shifts, although not the same composition values, were observed in u phases formed by second and by third long-period transition elements.3'4 This behavior, very characteristic of o phases, is in rather sharp contrast to the usually quite well-behaved stoichi-ometry of the Laves phases. In the latter, the AB2 stoichiometry predominates, with A the large atom and B the small atom.= The p phase occurs in the four binary systems of Mo or W with Fe or Co. On the basis of their crystal structure determination, Arnfelt and westgren6 ascribed to the p phase in the Co-W system the ideal composition W,Co7. Since all four binary pphases have nearly the same composition, it would seem quite plausible that some definite stoichiometry such as A6B7, might be characteristic of this phase, as AB2 is of the Laves phases. On the other hand, it has been noted,7 that the phases occur at average electron concentrations near to those at which the various cr phases are found. Also, it has been pointed out by Shoemaker and associates8 that structurally the a phases and the p phases are somewhat related to each other; both of these structures may be described in terms of suitable stackings of quasi-hexagonal layers'of atoms. By studying a suitably chosen ter- nary phase diagram, one might expect to be able to find out which one of the two conditions, the analogy with the o phase or the constant ratio between the number of large atoms and the number of small atoms in effect governs the behavior of the p phase. Several isothermal sections of ternary systems containing o phases have been investigated. In all cases where two binary o phases occur, these were found to be connected b a more or less straight ternary o phase field.7' '10 Such elongated o phase fields were also found in ternary systems in which only one of the limiting binaries is known to contain o phase. In this manner a latent o forming tendency could be detected and the virtual composition of a "binary o phase", which does not actually occur as such was approximately determined by extrapolation. The behavior of the phases, including their composition shift, is analogous to that of the classical electron compounds, as described by Hume-Rothery.11 In order to decide whether the p phase is essentially a "size compound" like the Laves phases, where a fixed stoichiometric ratio is quite generally maintained between the "large atoms" and the "small atoms", or whether the p phase is typically an "electron compound" in the same sense as ois, it was decided to investigate an isothermal section of the Mo-Mn-Co system. The Mo-Co system12 and the Mo-Mn system13 each are known to have a binary o phase. It could be therefore expected that a ternary o phase field will connect these two binary cr-phase fields. The p phase is known to occur in the Mo-Co system. If the p phase should turn out to form an elongated phase field extending deep into the ternary system, the following considerations mighto apply. The atomic radius of manganese (1.314for C.N.12) is between the va,lues for Mo (1.40Afor C.N.12) and for Co (1.26Afor C.N.12). If it is assumed that p is a "size compound", and that Mn is substituting for the smaller Co atoms in the p-structure in the ternary system, the y-phase field might be expected to extend parallel to the Mn-Co binary line. If Mn is substituting for the large Mo atoms in the p-structure, the p-phase field may be expected to extend parallel to the Mn-Mo binary line. On the other hand, if the p-phase turns out to be an "electron compound" like o, the ternary p-phase field should extend parallel to the ternary o -phase field connecting (Mo,Mn)owith (Mo, Co) a

Jan 1, 1961

By Fred C. Bond

IN crushing and grinding the larger particles are more exposed to the work input. They absorb most of the work and protect the smaller neighboring particles from destructive contact with the crushing surfaces or grinding media. The importance of this exposure differential upon the reduction efficiency and product size distribution has long been recognized. Unfortunately, there has heretofore been no direct method of evaluating it, and such indirect methods as observing the slope of the plotted product size distribution line have been used as an indication. In this presentation the Third Theory of Comminution1 has been used, together with the exponential formula for size distribution, to evaluate the exposure ratio and exposure constant and to illustrate examples of their utility in crushing and grinding applications.

Jan 12, 1957

By John F. Blandy

The map on Plate I illustrates a part of the works of the Red Bank Mining Company, on the Upper Freeport seam of coal, in Armstrong County, Pennsylvania. The contour lines give a careful representation of the conformation of the surface, showing also the line of outcrop of the seam, and the gangways of the mines are shown by the black lines. Upon assuming charge of the works in January last, I found that the first and greatest difficulty lay in the great uncertainty of the

By Neils Hansen

The microstructure of dispersion-strengthened aluminum aluminum-oxide products containing from 0.2 to 4.7 wt pct of aluminum oxide has been examined by optical and transmission electron microscopy, and the flow stress has been determined at room temperature and at 400C by tensile testing. Products were examined as recrystallized and as high-temperature extruded, and the microstructures consisted of a fine dispersion of oxide particles in a matrix divided by respectively recrystallized grain boundaries and subgrain boundaries. The flow stress (0.2 pct offset) at room temperature of recrystallized dispersion strengthened aluminum aluminum-oxide products is the superposition of dispersion strengthening and grain boundary strengthening. This superposition has been found to be linear. The flow stress (a) can be related to the grain size (t) by the Petch equation: ing content of oxide and k is a constant independent of the oxide content. For extruded products a similar relation has been found by replacing the grain size by the subgrain size. The k-value is of the same order for the two types of structure, which shows that the subgrain boundaries are as effective slip barriers as grain boundaries. Tensile testing at 400C of re-crystallized and extruded products shows that oxide dispersion strengthening is very effective, whereas the strengthening effect of grain boundaries and subgrain boundaries is small. THE microstructure of dispersion-strengthened products consists of hard particles finely distributed in a metal matrix. The strengthening effect of the dispersed phase has been fairly well established,1 and it has been found that the size and volume fractions of the dispersed particles are important structural parameters. However, in many dispersion-strengthened products which have been worked and heat-treated during manufacture the matrix is divided into well-defined grains or sub-grains, which may also have a strengthening effect. A model of the matrix strengthening in dispersed products worked during manufacture has been proposed,2 introducing the energy of the structure as a strengthening factor, especially at low temperatures. A difficulty in this model is, however, to relate this (stored) energy to the structural parameters directly observable as for instance grain size. The strengthening effect of the matrix grain size after recrystallization has been in- vestigated for nickel-thoria (TD-Nickel) products3 and for copper aluminum-oxide products. Conclusive results were, however, not obtained as the grain size of TD-nickel was constant. 5 to II , after recrystallization at temperatures from 700 to 1200°C and as the copper products containing 5 to 1 wt pct of aluminum oxide could not be recrystallized even after severe cold reduction and heat treatment at 1050C. For aluminum aluminum-oxide products containing from 1 to 5 wt pct of aluminum oxide it has been shown that the tensile strength at room temperature decreases when an extruded product is cold-worked and recrystallized. The matrix in the extruded products is divided into well-defined subgrains of micron size, and as the grain size of the recrystallized products is about two orders of magnitude higher, it is obvious that grain boundary strengthening occurs. Preliminary results8 have indicated that the flow stress containing no grain boundaries, A is a constant and t is the subgrain size. At elevated temperatures the effect of boundaries is more complex; it has been shown11 that recrystallized products having an oxide content of about 3 wt pct are more creep resistant than extruded material in the temperature range 400° to 600°C, whereas on application of a higher strain rate the tensile flow stress (0.2 pct offset) is higher in extruded than in recrystallized aluminum—5 wt pct aluminum oxide products at temperatures from room temperature to 427°C (800), Finally it has been shown12 that the Brinell hardness at 350°C of extruded products having about the same content of aluminum oxide increases with decreasing grain size, determined by X-ray line-width measurements. The present study was undertaken to obtain a quantitative relationship between the tensile strength and the grain size of aluminum aluminum-oxide products in the recrystallized as well as in the extruded state. The tensile testing was performed at room temperature and at 400uC. The grain size of the recrystallized products was varied by changing the degree of cold-work preceding the recrystallization heat treatment. In extruded products grain (or subgrain) size variations were obtained by high-temperature heat treatment after extrusion. EXPERIMENTAL a) Materials. Aluminum aluminum-oxide products have been manufactured by consolidation of aluminum powder covered with a layer of aluminum oxide formed during powder manufacturing. The products examined were manufactured from atomized powder containing

Jan 1, 1970

By T. E. Scott, D. H. Sherman, C. V. Owen

Mechanical properties and optical metallographic characteristics of vanadium containing 53 ppm (wt) H were investigated from, 77° to 298°K. A sharp ductile to brittle transition induced by the presence of hydrogen was observed between 238° and 223°K and a mar-tensitically formed hydride appeared at 200°K. While there appears to be a subtle relationship between the hydride formation and the ductile-brittle transition, it was concluded that the hydride per se was not sufficietzt to cause the severe em brittletnent. On the basis of the metallographic experiments and the results of a Petch analysis it is suggested that the mechanism of the embrittlement involves a reduction of the true surface energy, or cohesion, of the uanadiunz. THAT hydrogen can severely embrittle vanadium is well-documented;'-5 however, the mechanism by which hydrogen induces the observed embrittlement has not been established. It is not known whether the embrittlement of vanadium is caused by the formation of vanadium hydride or by a more subtle role of hydrogen. Until very recently6>' the solid solubility of hydrogen in vanadium at temperatures in the,range of the embrittlement was not known to a useful accuracy. In general, a severe embrittlement of the type produced by the presence of hydrogen in vanadium can be caused by changes in either of two properties of a metal. Either the yield stress of the metal is raised to the extent that plastic deformation at the tip of a crack cannot occur or the cohesive properties of the metal are reduced, at least locally, to the point at which cleavage is the natural response to applied loads. Of course a combination of these is possible. It is not known which of these properties of vanadium is influenced most by the addition of hydrogen. The purpose of this investigation was to determine the role of hydrogen in the embrittlement of vanadium. Accordingly, the solubility of hydrogen in vanadium in the temperature range where embrittlement is most severe was determined, the appearance of vanadium hydride was examined in relation to the initial ductile to brittle transition temperature, and an attempt was made to evaluate the effect of hydrogen on the yield stress and cohesive properties of vanadium. MATERIAL AND PROCEDURES Sample Preparation. The vanadium used in this investigation was prepared by the iodide refining process described by Carlson and owen.' Three ingots, 3 in. diam by 6 in. long, were cold-swaged to 0.096 in. diam, cut into short lengths, and then arc-melted under purified argon into one ingot. This process was repeated to insure a uniform composition in the final ingot. Chemical analysis of the metal is given in Table I. On the basis of work of Loria et a/ .' the following sequence of treatments was performed in order to obtain a uniform equiaxed ultimate grain structure: a) cold swage q-in.-diam ingot to 0.230 in. diam; b) anneal 6 hr at 1000°C in vacuum; c) by cold swaging reduce 81 pct in area in three steps: 0.230 to 0.187 in. diam, 0.187 to 0.150 in. diam, 0.150 to 0.096 in. diam. This sequence provided the desired grain structure after subsequent annealing treatments. Because annealing in evacuated quartz capsules resulted in contamination by oxygen, all anneals in this investigation were performed in a 304 stainless-steel chamber under a dynamic vacuum of 10- I Torr with the vanadium wrapped in tantalum foil. Prior to all annealing treatments the wires were electropolished for 1 min at 16°C in an 80 pct methanol-20 pct sul-furic acid electrolyte at 12.5 v. Following the final reduction the 0.096-in.-diam wire was cut into 2-in. lengths. A 1-in. gage section was reduced to 0.090 in. diam by electropolishing as above. Five different grain sizes were obtained by annealing the 2-in. samples at different temperatures for 8 hr to insure uniform grain size and residual hydrogen removal. The annealing temperatures used and the resulting grain sizes are given in Table 11. The final step in sample preparation was to charge half of the specimens of each grain size with hydro-

Jan 1, 1969

By Edward W. Parker

One of the most important features of the coal-mining industry of the present day is one that is common to the majority of industrial enterprises—the substitution of mechanical methods for hand-labor.

Jan 1, 1900

By Yoshinao Nakada

In many experiments involving electropolishing such as electropolishing during deformation and electrothinning of deformed metals for electron microscopy, it is usually assumed that the specimen temperature is the same as the temperature of the polishing bath. In order to test this assumption, the interior temperature of aluminum single and polycrystals was measured while they were being electropolished. Specimens were 1/4 by 1/4 by 6 in. and were of 99.99 pct purity. A small hole 1 in. deep was drilled axially at one end of the specimen so that a copper-constantan thermocouple could be inserted. The electropolishing solution was 4 parts methanol (reagent grade) and 1 part perchloric acid (70 pct). The electropolishing was performed using an apparatus shown in Fig. 1. The electropolishing solution was stirred by a motor-driven stirrer and was cooled to —5°C with a mixture of methanol and dry ice. Electrolyte temperature was measured and remained at -5°C during the electropolishing. Current density of 0.3 amp per sq. cm was used. When the current was turned on, after about a 5-sec delay, the temperature began to rise rapidly until it reached 65°C. In order to determine whether the temperature measured was localized, the thermal expansion of the specimen was meas-

Jan 1, 1965

By E. H. Kelton

The purposes of this paper are to describe the use of adjustable cut and draw tools as a control test of drawing properties and to point out that no other well-known test or combination of tests determines this quality in zinc and zinc alloys. Rolled zinc has been used for making drawn articles, particularly battery cans, for many years. The development of rolling treatments satisfactory for these purposes followed the usual course of trial and error experimentation depending upon cooperation with customers to determine what type of material was suitable. A quick test of drawing quality was highly desirable, of course. Scleroscope hardness and temperll having no apparent relation to drawing quality, were used simply to check the duplication of rolling treatment and grade of metal. The dynamic ductility1 test, on the other hand, was believed to be so like the drawing operation as to provide a reliable index and came to be taken as the criterion of good drawing properties. Faith in this test was strengthened by the fact that metal having the highest ductility was more satisfactory for operations, such as the manufacture of battery cups, that required several redraws. No distinction was made at that time in specifying metal as to whether it was to be subjected to simple cut and draw, redrawing or forming operations. It developed, however, that in some grades of metal the highest ductility did not coincide with the most satisfactory quality when the material was used for a single draw. When zinc-base alloys, with their wider ranges of effective rolling treatments, came into increased use, their dynamic ductility and drawing quality appeared to have no connection whatever. Furthermore, comparisons of known drawing quality with other physical properties of the metal, including tensile strength, elongation and dynamic cold bends, were fruitless in yielding any clear relationship. Almost any test value produced in one piece of metal could be duplicated by another rolling or annealing treatment with attendant different drawing characteristics.

Jan 1, 1934

Jan 1, 1906

By E. D. Slone, F. L. Dillard

When a new mine is in the planning stages, one of the most important decisions to be made is the selection of' face haulage equipment and the interrelated transportation system to the surface. Equally important is the method of transporting personnel supplies and repair parts from the surface to the working places. When Bell & Zoller management elected to open the new Zeigler mine in the No. 9 seam near Madisonville, Ky., last year, various transportation systems were considered. It was agreed early that a slope mine would be preferred to a shaft mine, and that belt conveyors would be more economical than a rail system.

Jan 1, 1970

By J. G. Thompson

Determinations of the hydrogen content of irons and steels invariably are subject to two serious difficulties: (I) the determination of amounts of 0.001 per cent or less of any constituent requires an analytical procedure of unusual precision and accuracy, and (2) the hydrogen content of many samples is dccidedly not stable; i.e., there is no assurance that the content at the time the analysis is made is the same as it was when the sample was taken or at some previous time in the history of the piece. In respect to both the precision and speed of the determination, the vacuum-extraction procedure for the determination of hydrogen possesses advantages over the vacuum-fusion procedure, which has been the recognized standard for the detcrmination of other gaseous elements in sted-— oxygen and nitrogen for example. The basic facts upon which the vacuum-extraction procedure is based—i.e., the evolution of gas from solid steel when it is heated in vacuum, and the fact that the evolved gas is rich in hydrogen—were observed by Graham1 many years ago. Subsequent investigations have shown that hydrogen exists in steel chiefly as interstitial solid solution (i.e., in atomic dispersion) and perhaps to some extent as hydridcs that are unstable and decompose to form atomic hydrogen. In either case practically all of the hydrogen in steel at elevated temperatures exists in the atomic condition and consequently is able to diffuse readily through the metal. In contrast to this, other gaseous elements, such as oxygen and nitrogen, normally are present in steel chiefly in the form of relatively stable compounds such as oxides or silicates and nitrates; i.e., the oxygen and nitrogen atoms are fixed in stable combinations and are not free to migrate. The only oxygen or nitrogen that can diffuse in steel is the small amount in solution (atomically dispersed) and the rate of diffusion of these atoms is much less than that of hydrogen because of their greater atomic volume and lower mobility. Consequently, it is possible to extract most or all of the hydrogen from solid steel in a reasonable time at moderately elevated temperatures, but the procedure is not applicable to the determination of oxygen or nitrogen. It is only within the last decade that these observations have been developed into an analytical procedure for the determination of hydrogen. Apparatus and Procedure The apparatus used at the National Bureau of Standards,6 for the determination of hydrogen by the vacuum-extraction procedure, is shown schematically in Fig. I. The specimen, freshly cleaned and dried,* is suspended on a fine wire within the quartz furnace tube that is connected to the reservoir system and analytical train.

Jan 1, 1945

By P. E. Hopkins

In speaking of the economic geology of southeastern Ontario, W. G. Miller and C. W. Knight1 say that "there occurs in southeastern Ontario a variety of minerals and rocks of economic value, probably as great as in any district of like size on the North American continent. Some of these deposits, including marble and trap, are inexhaustible. Others, including talc and iron pyrites, have proved to be of considerable economic importance. From time to time, during the last 50 years, the following minerals and rocks have been mined or quarried with varying success: gold, iron pyrites, zinc blende, copper pyrites, galena, mispickel, magnetite, hematite, talc, actinolite, mica, marble, ophicalcite, feldspar, fluorite, apatite, corundum, graphite and sodalite. All of the economic materials, with, the exception of fluorite, appear to be of pre-Cambrian age. The fluorite veins penetrate the Ordovician, Black River, limestone." Accompanying that report was an article by the writer on the Queens-boro Pyrite Area which includes one of the two working pyrite properties in southeastern Ontario. In the present paper will be given a brief description2 of all the known pyrite deposits in the area which may at some time possess an economic value, with fuller descriptions of the two working mines—The Canadian Sulphur Ore C,o.'s mine near Queensboro, and the Nichols Chemical Co.'s property at Sulphide. The earliest mining of iron pyrites in Ontario was done in 1868 on the Billings property near Brockville. The mines were closed down in 1879 under the assumption that they were exhausted. Many other

Jan 1, 1917

By R. D. Satterley

The Sherwood mine is an iron-ore mine owned and operated by the Inland Steel CO. in the Iron River district of the Menominee Range in Michigan. The property consists of an 80-acre tract in the village of Mineral Hills, about a mile north of the city of Iron River. The Ore mined is a reddish brown, nonbessemer hematite and limonite. The ore bodies lie in a large syncline having an east-west strike and are associated with a rock structure that is folded in a complex manner. The two 40-acre tracts run north and south and the shaft is at about the center of the north forty. The shaft is 1286 ft. deep, with the principal operating level at a depth of 1000 ft. from surface. A new level at a depth of 1200 ft. is in process of development. The ore body at the 1000 ft. level is east and west at approximately the line between the north and south forties and at this elevation is from 50 to 250 ft. wide and extends above the level at varying heights of from 50 to 250 feet. The 1000-ft. haulage drift extends south from the shaft, through the east-west ore body to the slates on the south side of the body. The ore body was intercepted in the drifting at about goo ft. from the shaft and was about 200 ft. wide at that point. A crosscut was extended to the east and west property lines along the south boundary of the ore body. This east-west ore body is laid out in areas go ft. wide for stoping with pillars 40 ft. wide. With this plan a stope is approximately 80 by 200 ft. and has a pillar on both sides that is approximately 40 by 200 ft. The ore has a height of from 50 to 250 ft. above the elevation of the level, therefore the height of the stopes varies in accordance with the height of the ore body at each location. From the crosscut, two main raises, each 6 by 7 ft., are put up into each 80 ft. stope area (Fig. 1). One of the main raises serves as a manway and the other as an ore raise, through which the ore is transferred from the stope to the tramming equipment. The original layout as for scraping of the ore from under the stopes into the ore raises. The ore raise is put halfway (east and west) along the 80-ft. stope area and usually is in iron formation. The manway and ore raise are on approximately 15-ft. centers. These main raises are Put up to a height of from 22 to 30 ft. above the level floor, then from the toll of the ore raise a scraper drift (8 X 8 ft.) is driven across the width of the ore body, which is in the neighborhood of 200 ft. From the scraper drift, mill raises are put up at 12½-ft. centers, staggered on opposite sides of the drift, and these are extended 23 ft. above the elevation of the scraper-drift floor. The sublevel connecting the top of these mill raises is called a mill "sub." Other sublevels are developed parallel to the scraper and mill subs at 25-ft. vertical intervals above the mill sub. The mill sub and the other subs above the mill sub are known as sublevels or dog drifts, and are 4 ft. wide and 6 ft. high. These dog drifts

Jan 1, 1946