Search Documents

By A.S. Richardson

AIR conditioning, or air cooling, for the improvement of ventilation in the Butte mines has come into increasing use during the past 10 years. In part, the methods practiced have been described in previous publications of the Institute, but some improvements on earlier methods have been made and a number of new features have been developed. This paper is presented as a record of progress made, and for the sake of completeness describes all general features of the work. The need for air conditioning in the ventilation of mines in the district arises from the fact that the temperature of the ground and mine water has shown a very great increase with increase in mining depth, and has now reached a maximum of slightly over 130°F. The most difficult part of the ventilation problem is the maintenance of temperature and humidity of a satisfactory standard in the working places, especially on the lower levels. Although ordinary ventilation is adequate to maintain good conditions in most of the working places it is subject to a number of limitations at great depth. Most important among these limitations is that with increase in depth the air becomes heated before it reaches the working places, both by compression from increase in atmospheric Pressure and by heat transferred to it from rock at high temPerature, so that its capacity for lowering temperatures is greatly reduced before it reaches the operating zone. Increasing depth of mining also increases the distance traveled by the air in its passage through the mine, and this causes a corresponding increase in resistance to air flow, so that there is greater difficulty in maintaining even the same volume in circulation. Thus, in the face of a demand that the ventilating system have a very much greater capacity to remove heat from the mine, the tendency is for that capacity to diminish. The only evident alternatives were (I) the opening of additional air shafts to increase the volume of air in circulation, (2) an extension of the existing system that would be subject to the same limitations, or (3) the adoption of an entirely different method such as air cooling. Fortunately for an economic solution of the problem, the mean annual temperature of the surface atmosphere at Butte is about 40°F., with very low relative humidity in summer, so that there is unlimited natural cooling power at a temperature range adaptable to air-conditioning methods. Methods Two similar methods of air conditioning are used, as necessitated by service requirements and dependent upon the equipment available. In one, which is the more important and has the greater cooling capacity, water is circulated in a closed circuit, and, alternately, first absorbs heat from warm mine air and then dissipates it in the surface atmosphere by cooling at a cooling tower. The second

Jan 1, 1943

By A. S. Richardson

AIR conditioning, or air cooling, for the improvement of ventilation in the Butte mines has come into increasing use during the past 10 years. In part, the methods practiced have been described in previous publications of the Institute, but some improvements on earlier methods have been made and a number of new features have been developed. This paper is presented as a record of progress made, and for the sake of completeness describes all general features of the work. The need for air conditioning in the ventilation of mines in the district arises from the fact that the temperature of the ground and mine water has shown a very great increase with increase in mining depth, and has now reached a maximum of slightly over 130°F. The most difficult part of the ventilation problem is the maintenance of temperature and humidity of a satisfactory standard in the working places, especially on the lower levels. Although ordinary ventilation is adequate to maintain good conditions in most of the working places it is subject to a number of limitations at great depth. Most important among these limitations is that with increase in depth the air becomes heated before it reaches the working places, both by compression from increase in atmospheric Pressure and by heat transferred to it from rock at high temPerature, so that its capacity for lowering temperatures is greatly reduced before it reaches the operating zone. Increasing depth of mining also increases the distance traveled by the air in its passage through the mine, and this causes a corresponding increase in resistance to air flow, so that there is greater difficulty in maintaining even the same volume in circulation. Thus, in the face of a demand that the ventilating system have a very much greater capacity to remove heat from the mine, the tendency is for that capacity to diminish. The only evident alternatives were (I) the opening of additional air shafts to increase the volume of air in circulation, (2) an extension of the existing system that would be subject to the same limitations, or (3) the adoption of an entirely different method such as air cooling. Fortunately for an economic solution of the problem, the mean annual temperature of the surface atmosphere at Butte is about 40°F., with very low relative humidity in summer, so that there is unlimited natural cooling power at a temperature range adaptable to air-conditioning methods. Methods Two similar methods of air conditioning are used, as necessitated by service requirements and dependent upon the equipment available. In one, which is the more important and has the greater cooling capacity, water is circulated in a closed circuit, and, alternately, first absorbs heat from warm mine air and then dissipates it in the surface atmosphere by cooling at a cooling tower. The second

Jan 1, 1943

By Raymond Mancha

The purpose of an accurate underground pressure survey is to obtain a pressure gradient along the circuit or circuits under investigation. The pressure gradient shows the rate of pressure drop between various observation points along a circuit. This determines excessive resistance regions and the economic feasibility of correcting such conditions by cleaning airways, driving additional airways, or modifying existing airways. A pressure gradient is useful for predicting the effect on other parts of the circuit when adjusting the air regulation on any one split or when planning a field airshaft or slope or a new drift to the outcrop. A single-compartment airshaft often produces disappointing results because it relievcs only a part of the circuit instead of the over-all mine pressure. It is valuable to know how the circuit pressure drop is distributed. The underground pressure survey is used also to determine the friction coefficient for various types of airway. High precision work is required to establish these vital data for predicting the characteristics of mine pressure volume when projecting new mine developments. Methods Regardless of the type of instrument used to conduct a circuit pressure survey, the work should preferably be performed at a time when the mine is idle, in order to avoid air-flow disturbances from moving trips and cages or from the opening or closing of trap doors. Preferably the survey should be made when the barometer is comparatively steady, to restrict variation in the air specific weight at observation stations while the circuit is traversed. The two most commonly used instruments for underground pressure surveys are: (I) the altimeter; (2) the inclined manometer with hose extensions. The altimeter is sufficiently accurate for determining the underground pressure gradient and is preferable to the nianometer for such work because of greater flexibility and shorter time required for the traverse. With the altimeter it is possible to select more widely separated observation stations than is practical with the manometer, with its restricted hose extension lengths. The altimeter also permits easier travel along haulage roads between airway observation stations, avoiding badly obstructed airways. The inclined manometer is more reliable than the altimeter for establishing friction coefficients in mine airways. Manometer readings are unaffected by differences in elevations between stations, which require corrections to altimeter data. The manometer provides direct reading without temperature correction, which may or may not be true with the altimeter, depending upon the make of instrument used. The elimination of correction factors combined with the instantaneous, simultaneous and

Jan 1, 1947

By Raymond Mancha

The purpose of an accurate underground pressure survey is to obtain a pressure gradient along the circuit or circuits under investigation. The pressure gradient shows the rate of pressure drop between various observation points along a circuit. This determines excessive resistance regions and the economic feasibility of correcting such conditions by cleaning airways, driving additional airways, or modifying existing airways. A pressure gradient is useful for predicting the effect on other parts of the circuit when adjusting the air regulation on any one split or when planning a field airshaft or slope or a new drift to the outcrop. A single-compartment airshaft often produces disappointing results because it relievcs only a part of the circuit instead of the over-all mine pressure. It is valuable to know how the circuit pressure drop is distributed. The underground pressure survey is used also to determine the friction coefficient for various types of airway. High precision work is required to establish these vital data for predicting the characteristics of mine pressure volume when projecting new mine developments. Methods Regardless of the type of instrument used to conduct a circuit pressure survey, the work should preferably be performed at a time when the mine is idle, in order to avoid air-flow disturbances from moving trips and cages or from the opening or closing of trap doors. Preferably the survey should be made when the barometer is comparatively steady, to restrict variation in the air specific weight at observation stations while the circuit is traversed. The two most commonly used instruments for underground pressure surveys are: (I) the altimeter; (2) the inclined manometer with hose extensions. The altimeter is sufficiently accurate for determining the underground pressure gradient and is preferable to the nianometer for such work because of greater flexibility and shorter time required for the traverse. With the altimeter it is possible to select more widely separated observation stations than is practical with the manometer, with its restricted hose extension lengths. The altimeter also permits easier travel along haulage roads between airway observation stations, avoiding badly obstructed airways. The inclined manometer is more reliable than the altimeter for establishing friction coefficients in mine airways. Manometer readings are unaffected by differences in elevations between stations, which require corrections to altimeter data. The manometer provides direct reading without temperature correction, which may or may not be true with the altimeter, depending upon the make of instrument used. The elimination of correction factors combined with the instantaneous, simultaneous and

Jan 1, 1947

By Raymond Mancha

The use of blower fans and tubina- for auxiliary face ventilation is a somewhat controversial subject. Most authorities agree upon the advantages of this system over the maintenance of line brattice for dead-end ventilation. They also recognize the system's disadvantages. However, there is considerable disagreement as to the proper relation of the advantages to the disadvantages. It is the purpose of this report to present the opinions of four authorities of diversified occupation and permit the reader to form his own opinions on the subject. ORsErvers Carel Robinson is a mining engineer consultant of wide repute, who has a background of operating experience. Thomas G. Fear is a mine operator whose present position is that of chief engineer for the Hanna Coal Co. at St. Clairsville, Ohio. E. H. Denny is chief of the Coal Mine Inspection Division of the U. S. Bureau of Mines, and is a very able engineer whose past experience well qualifies him to appraise this problem. Cloyd M. Smith, editor of the periodical Mechanization, is a ventilation consultant. For a number of years he was a member of the Mining Department of the University of Illinois and has studied mine ventilation for many years. It is Mr. Robinson,s opinion that closely spaced breakthroughs, although conducive to low gas accumulation past the last open crosscut during the driving of entries, are difficult to maintain and are constant Sources of fugitive air. Jute or canvas brattice is suitable for entry driving with

Jan 1, 1944

By Raymond Mancha

The use of blower fans and tubina- for auxiliary face ventilation is a somewhat controversial subject. Most authorities agree upon the advantages of this system over the maintenance of line brattice for dead-end ventilation. They also recognize the system's disadvantages. However, there is considerable disagreement as to the proper relation of the advantages to the disadvantages. It is the purpose of this report to present the opinions of four authorities of diversified occupation and permit the reader to form his own opinions on the subject. ORsErvers Carel Robinson is a mining engineer consultant of wide repute, who has a background of operating experience. Thomas G. Fear is a mine operator whose present position is that of chief engineer for the Hanna Coal Co. at St. Clairsville, Ohio. E. H. Denny is chief of the Coal Mine Inspection Division of the U. S. Bureau of Mines, and is a very able engineer whose past experience well qualifies him to appraise this problem. Cloyd M. Smith, editor of the periodical Mechanization, is a ventilation consultant. For a number of years he was a member of the Mining Department of the University of Illinois and has studied mine ventilation for many years. It is Mr. Robinson,s opinion that closely spaced breakthroughs, although conducive to low gas accumulation past the last open crosscut during the driving of entries, are difficult to maintain and are constant Sources of fugitive air. Jute or canvas brattice is suitable for entry driving with

Jan 1, 1944

By Leo H. Glanville

Until 1934, natural ventilation was depended upon in the mine of the Climax Molybdenum Co. at Climax, Colorado. In that year a 7-ft. axial-flow, low-pressure fan was installed as an exhausting unit. In 1936, three more fans of the same kind were installed, all as exhausting units, with a total capacity of 115 000 cu, ft. per min., and since then fans and sprays have been added as required. Atmospheric Conditions Adverse atmospheric conditions at this elevation of 11,500 ft. account in part for difficulty in maintaining adequate ventilation throughout the mine. Barometric pressures range from 18.99 to 20.01 in. of mercury; the norma1 average being 19.70 in. Air weight is 0.051 lb. per cu. ft., and humidity is low—about a 30 per cent yearly average. This makes the use of mechanical humidity aids mandatory the Year around to prevent excessive dryness of the mine workings and the resultant dust hazard. The yearly temperature range is from minus 24" to 75°F.; typically, in February 1942 the mean low was minus 3.25°F. and the mean high, 21.3°F. In August the mean low was 34.8°F.; the mean high, 64.26°F. Even during the summer month air filtration through the openings of the cave area is 32°F., owing to accumulation of snow in the glory hole and in Part to glacial ice, which, combined with a rock temperature of 39°F. on the upper levels (elevation 11,945 ft.) and 42°F. on the main haulage level (elevation 11,470 ft.], makes it difficult to maintain a comfortable working temperature. The one advantage in ventilation of mine workings at the altitude of the Climax mine is that the power required to circulate a given air volume is 32 per cent less than would be required at sea level. Problems since 1936 the mine management has studied intensively plans for providing adequate ventilation for the entire mine for its expected life. As the ore breaks into large pieces, much secondary blasting is necessary, therefore there is a considerable amount of smoke, gas and dust, which requires circulation of a large amount of air to remove the contamination, It is undesirable to use haulage drifts and manways as air passages because some would be passageways for contaminated air also, and there would be undesirable high velocities in some drifts. High velocities and large volumes of subfreezing air dry out the passageways through which they pass, and thus increase the amount of dust. Regulating doors in haulage drifts are difficult of upkeep and interfere with production. It was decided as a general principle to distribute fresh air to each working place at low velocities and low pressures and to remove contaminated air as soon as possible with a minimum of travel through working places.

Jan 1, 1943

By Leo H. Glanville

Until 1934, natural ventilation was depended upon in the mine of the Climax Molybdenum Co. at Climax, Colorado. In that year a 7-ft. axial-flow, low-pressure fan was installed as an exhausting unit. In 1936, three more fans of the same kind were installed, all as exhausting units, with a total capacity of 115 000 cu, ft. per min., and since then fans and sprays have been added as required. Atmospheric Conditions Adverse atmospheric conditions at this elevation of 11,500 ft. account in part for difficulty in maintaining adequate ventilation throughout the mine. Barometric pressures range from 18.99 to 20.01 in. of mercury; the norma1 average being 19.70 in. Air weight is 0.051 lb. per cu. ft., and humidity is low—about a 30 per cent yearly average. This makes the use of mechanical humidity aids mandatory the Year around to prevent excessive dryness of the mine workings and the resultant dust hazard. The yearly temperature range is from minus 24" to 75°F.; typically, in February 1942 the mean low was minus 3.25°F. and the mean high, 21.3°F. In August the mean low was 34.8°F.; the mean high, 64.26°F. Even during the summer month air filtration through the openings of the cave area is 32°F., owing to accumulation of snow in the glory hole and in Part to glacial ice, which, combined with a rock temperature of 39°F. on the upper levels (elevation 11,945 ft.) and 42°F. on the main haulage level (elevation 11,470 ft.], makes it difficult to maintain a comfortable working temperature. The one advantage in ventilation of mine workings at the altitude of the Climax mine is that the power required to circulate a given air volume is 32 per cent less than would be required at sea level. Problems since 1936 the mine management has studied intensively plans for providing adequate ventilation for the entire mine for its expected life. As the ore breaks into large pieces, much secondary blasting is necessary, therefore there is a considerable amount of smoke, gas and dust, which requires circulation of a large amount of air to remove the contamination, It is undesirable to use haulage drifts and manways as air passages because some would be passageways for contaminated air also, and there would be undesirable high velocities in some drifts. High velocities and large volumes of subfreezing air dry out the passageways through which they pass, and thus increase the amount of dust. Regulating doors in haulage drifts are difficult of upkeep and interfere with production. It was decided as a general principle to distribute fresh air to each working place at low velocities and low pressures and to remove contaminated air as soon as possible with a minimum of travel through working places.

Jan 1, 1943

By C. B. Foraker

THE Magma mine, of the Magma Copper Co., at Superior, Pinal County, Arizona, is 68 miles east of Phoenix and 21 miles west of Miami, Arizona, on highway U. S. 180. Temperatures and Underground Waters Surface Temperatures.—The average surface dry-bulb temperature at Superior is 72.4°; wet-bulb, 57.4°; with an indicated relative humidity of 38 per cent. The average yearly rainfall from 1921 to 1936, inclusive, was 18.74 in. The maximum condition of the atmosphere is in June, July and August, and the minimum is in January and February. The surface temperatures, of course, influence the temperatures of the downcast shafts; however, the variation between winter and summer causes a difference of only 2" to 3" in the stopes and working places that are not close to the intake shafts. Average atmospheric conditions are shown in Fig. 1. Rock Temperatures.—Rock temperatures on the deeper levels of the mine are as follows:

Jan 1, 1940

By C. B. Foraker

THE Magma mine, of the Magma Copper Co., at Superior, Pinal County, Arizona, is 68 miles east of Phoenix and 21 miles west of Miami, Arizona, on highway U. S. 180. Temperatures and Underground Waters Surface Temperatures.—The average surface dry-bulb temperature at Superior is 72.4°; wet-bulb, 57.4°; with an indicated relative humidity of 38 per cent. The average yearly rainfall from 1921 to 1936, inclusive, was 18.74 in. The maximum condition of the atmosphere is in June, July and August, and the minimum is in January and February. The surface temperatures, of course, influence the temperatures of the downcast shafts; however, the variation between winter and summer causes a difference of only 2" to 3" in the stopes and working places that are not close to the intake shafts. Average atmospheric conditions are shown in Fig. 1. Rock Temperatures.—Rock temperatures on the deeper levels of the mine are as follows:

Jan 1, 1940

By A. S. Richardson

Ventilation of the Butte mines has long been a rather difficult problem because of the natural high temperature of the rock. With increase* in mining depth, higher rock temperatures have been encountered, and this has caused a constantly growing demand for more effective ventilation measures. During recent years the hazards of dust in mine air have been more clearly recognized, and have necessitated the adoption of dust-prevention methods. To meet these ventilation problems in the mines of the Anaconda Copper Mining Co., a mines ventilation department was organized in 1918, to act under the direction of the general superintendent of mines. At the present time, under normal operating conditions, the force employed includes the ventilation engineer, two chief assistant ventilation engineers and eight assistant ventilation engineers. The activities of the department are, briefly: (1) planning and supervising operation of the general ventilation system; (2) planning and supervising the operation of dust-prevention measures, together with dust sampling and related microscopic work for the quantitation of the dust samples and determination of particle-size distribution; (3) the design and development of air-conditioning methods to meet present exceptionally severe temperature conditions and in anticipation of future requirements. To a large extent the technical features of the ventilation methods have been described in earlier papers by the author. This paper is written mainly to summarize past accomplishments bearing most closely on health and safety, with a somewhat more detailed account of the dust-prevention measures that have been developed comparatively recently. Facilitating Flow of Am As a basic requirement for the safety of the mcn, all ventilation plans are subject to a ruling that the main operating shafts must be maintained as inlet air courses. Under this condition, a safe, fresh-air escapeway is assured if a fire occurs within the mine, and the shaft; is available as a base

Jan 1, 1940

By A. S. Richardson

Ventilation of the Butte mines has long been a rather difficult problem because of the natural high temperature of the rock. With increase* in mining depth, higher rock temperatures have been encountered, and this has caused a constantly growing demand for more effective ventilation measures. During recent years the hazards of dust in mine air have been more clearly recognized, and have necessitated the adoption of dust-prevention methods. To meet these ventilation problems in the mines of the Anaconda Copper Mining Co., a mines ventilation department was organized in 1918, to act under the direction of the general superintendent of mines. At the present time, under normal operating conditions, the force employed includes the ventilation engineer, two chief assistant ventilation engineers and eight assistant ventilation engineers. The activities of the department are, briefly: (1) planning and supervising operation of the general ventilation system; (2) planning and supervising the operation of dust-prevention measures, together with dust sampling and related microscopic work for the quantitation of the dust samples and determination of particle-size distribution; (3) the design and development of air-conditioning methods to meet present exceptionally severe temperature conditions and in anticipation of future requirements. To a large extent the technical features of the ventilation methods have been described in earlier papers by the author. This paper is written mainly to summarize past accomplishments bearing most closely on health and safety, with a somewhat more detailed account of the dust-prevention measures that have been developed comparatively recently. Facilitating Flow of Am As a basic requirement for the safety of the mcn, all ventilation plans are subject to a ruling that the main operating shafts must be maintained as inlet air courses. Under this condition, a safe, fresh-air escapeway is assured if a fire occurs within the mine, and the shaft; is available as a base

Jan 1, 1940

By A. T. Beckwith

The Lehigh Navigation Coal Company Inc. operates steep-pitch, relatively deep mines in the Panther Creek Valley, at the eastern end of the southern anthracite coal field. Commercially minable coal beds are the Mammoth,† Primrose, Orchard, and Buck Mountain;‡ their respective thicknesses average 50, 15, 10 and 12 ft. Sand slates immediately overlie and underlie these beds, though in some locations sandstone or conglomerate beds occur. Underground operations extend to a depth of 1200 ft. below the surface, and comprise a bulk of virgin work on the lower levels, and a small amount of remining on the upper levels. With increase in depth, ventilation has become a more important factor. Development In early days slopes or drifts were driven in the outcropping coal on the hillsides. Subsequent development was by water-level tunnels, with portals above high water in Panther Creek. These tunnels have been maintained because they intercept and drain much water that enters the mined-out portion of the bed and otherwise would follow down to the deep workings+ Below these tunnels, the coal was customarily developed by slopes. Muleways, which are zigzag chutes easy to travel, were also driven to connect lower openings with the water levels. When it became necessary to go still deeper, the slopes were abandoned, and vertical multicompartment shafts were sunk from the surface. Levels have been at vertical intervals of from 175 to 250 ft. Recent practice has been toward the latter spacing, splitting the total lift, however, by starting to mine from chutes extending halfway up to the level above. Chutes customarily are spaced at 50, 60 or 70-ft. centers along the gangways. At some mines, additional shafts have been sunk from the surface to the level containing the main pumping station, and these carry the discharge lines from the pumps. As the mines are ventilated by the exhausting system, both the hoisting and so-called water shafts serve as intakes. The main fan is always on the surface, and is connected with the return airways from the various levels by an air hole or a vertical shaft. For economy, when the present deepest levels were developed, and return-air shafts or air holes were not extended to the new level, but connections were made from the new level to that above by two or more holes. It is doubtful that this method will be continued, as complications in the system, increased resistance to flow, and other difficulties undoubtedly will counterbalance any economies this provision may afford. During the early years of mining, when operations were at no great depth, all development headings were driven in the coal bed. As mining progressed downward, increased ground pressures slowed develop

Jan 1, 1942

By A. T. Beckwith

The Lehigh Navigation Coal Company Inc. operates steep-pitch, relatively deep mines in the Panther Creek Valley, at the eastern end of the southern anthracite coal field. Commercially minable coal beds are the Mammoth,† Primrose, Orchard, and Buck Mountain;‡ their respective thicknesses average 50, 15, 10 and 12 ft. Sand slates immediately overlie and underlie these beds, though in some locations sandstone or conglomerate beds occur. Underground operations extend to a depth of 1200 ft. below the surface, and comprise a bulk of virgin work on the lower levels, and a small amount of remining on the upper levels. With increase in depth, ventilation has become a more important factor. Development In early days slopes or drifts were driven in the outcropping coal on the hillsides. Subsequent development was by water-level tunnels, with portals above high water in Panther Creek. These tunnels have been maintained because they intercept and drain much water that enters the mined-out portion of the bed and otherwise would follow down to the deep workings+ Below these tunnels, the coal was customarily developed by slopes. Muleways, which are zigzag chutes easy to travel, were also driven to connect lower openings with the water levels. When it became necessary to go still deeper, the slopes were abandoned, and vertical multicompartment shafts were sunk from the surface. Levels have been at vertical intervals of from 175 to 250 ft. Recent practice has been toward the latter spacing, splitting the total lift, however, by starting to mine from chutes extending halfway up to the level above. Chutes customarily are spaced at 50, 60 or 70-ft. centers along the gangways. At some mines, additional shafts have been sunk from the surface to the level containing the main pumping station, and these carry the discharge lines from the pumps. As the mines are ventilated by the exhausting system, both the hoisting and so-called water shafts serve as intakes. The main fan is always on the surface, and is connected with the return airways from the various levels by an air hole or a vertical shaft. For economy, when the present deepest levels were developed, and return-air shafts or air holes were not extended to the new level, but connections were made from the new level to that above by two or more holes. It is doubtful that this method will be continued, as complications in the system, increased resistance to flow, and other difficulties undoubtedly will counterbalance any economies this provision may afford. During the early years of mining, when operations were at no great depth, all development headings were driven in the coal bed. As mining progressed downward, increased ground pressures slowed develop

Jan 1, 1942

By F. C. Sturges

For some time mining engineers have been interested in the possibility of using small diameter shafts, sunk by core drilling, as aids to ventilation and as emergency escapeways. The possibilities are interesting to contemplate, but new methods involve unknowns, and interest tends to remain passive until these unknowns are, solved. Recently we have completed two 36-in. diam core drilled shafts, and wish to make the data on these available to the industry. Both shafts were drilled for the McLain Fire Brick Co., one at its Buckeye mine and the other at its Colonial mine. Both mines are in the fireclay underlying the Lower Kittanning coal. Both mines have been in operation for a number of years and have required expensive maintenance work on return airways. It was decided that considerable savings could be effected by short-circuiting the air to the surface through small shafts. It was also realized that these holes, located near the present workings, would be of added value as emergency escapeways. Originally, 48-in. diam shafts were considered, but actual computations showed 36-in. diam shafts were more than ample at both mines. The shaft at the Buckeye mine is 240 ft deep, and that at the Colonial mine 258 ft deep. Both holes were started in the lower part of the Conemaugh formation and penetrated Conemaugh and Allegheny strata. The holes were started through the unconsolidated materials overlying bedrock by constructing a concrete collar with a wall thickness of 8 in. Then the shafts were drilled by the shot-core drill method. An annular groove was cut in the rock by the abrading action of chilled steel shot run under the shoe of the core barrel. The drilling was done in stages, the core barrel drilling the groove for a certain distance depending on conditions encountered, and then the cores broken off and taken out in sections. The core barrel had a 36-in. o.d. and the finished diameter of the shaft measured almost 37 in. The major questions that could not be answered until the completion of the first shaft were, (I) how much ground water would be encountered, how would it hinder the drilling, and how difficult would it be to seal off, and, (2) how would the walls of the hole stand up. The holes of course could .be cased or lined, but that is considerable added expense in any shaft.

Jan 1, 1949

By G. S. Jenkins

The statistics set forth by Professor Mitchell in a proceding paper very carefully brought out the points that indicate that a marked amount of consideration must be given to" the haulage problem to adapt it to local conditions as encountered. Professor Mitchell's paper showed a spread of from 10 tons per man to 50 tons per man on the production crews, which spread can be recognized as entirely too large when one considers that the product is being sold at a price within very close limits. While a portion of this spread may be explained by different methods in cost accounting as to what employees are applicable to the production crew, it cannot all be blamed on an accounting method. A good portion must be explained by the improper application of equipment to the needs incurred by the local conditions. It is in an endeavor to go into this phase that this paper is given. It will be necessary to qualify the points covered in order to keep the subject from becoming too wide in scope. Along this line, conditions will be only those involved in bituminous coal mine practices and only the haulage of coal that is loaded with mobile loading machines in seams 4 ft thick and better. Haulage Methods Employed The Consolidated Coal Co. (Illinois) has been operating on a modernized basis for about 20 yr. By modernized we mean the loading of coal with mobile loading equipment. In review of haulage methods, it must be remembered that the main line electric haulage locomotive has been in service for some 40 or jo years. To augment this main line haulage, the mule did a quite satisfactory job during hand-loading days, but was later replaced by the gathering locomotive, either battery or cable-reel operated. This type of haulage was the method in common use at the time the mechanical loading of coal became of major importance and the success or failure of loading machine installations may be largely accredited to haulage facilities in the early days; that is, in the period around 1930. The Consolidated Coal Co. had its struggle with this problem beginning in about 1927 or 1928. We were somewhat fortunate in that we were already using gathering locomotives powered by storage batteries at the time we introduced mechanical loading. This meant that we did not have to spend as much time training motormen and trip riders as many mines did that utilized only mules for their secondary haulage. This was all advantage, and our efforts could be focused on ways and means of providing adequate car service to the loading machine. Like most operations, we endeavored to gear the car service to the capacity of the machine, with a large crew endeavoring to load the maximum tonnage that the machine would handle. Toward that end our first move was to install switches

Jan 1, 1949

By Richard L. Ash, J. H. Kelley, W. H. McCracken, William Bellano, J. D. Morgan, D. R. Mitchell

Rubber-tired shuttle cars are finding increased use as gathering units in under-ground mines. As the name implies, they shuttle back and forth between the loading machine and the section transportation system. In many mines their use has in-creased the efficiency of the loading and gathering operations, resulting in increased output per man employed and decreased costs per ton. A car motivated by cable reel is shown in Fig I, and a car with battery power in Fig 2. A brief chronological account of the development of rubber-tired haulage equip-ment follows: 1936. J. H. Fletcher1 installed his first unit for the Blue Bird Coal Co., Carrier Mills, Illinois. This unit consisted of a battery-powered industrial tractor and a trailer with drop-bottom doors. The coal was transported for short distances to a hopper for discharge into mine cars. 1938. A battery-powered self-contained shut-tle car with rubber-tired wheels was built by the Joy Manufacturing Co. Two units were installed for the Katherine Coal Co., Lumberport, West Virginia. The shuttle car consisted of a materials-receiving body with a conveyor in the bottom to move the coal forward during loading and to unload the coal at the discharge station. 1938. A cable-powered shuttle car with four-wheel drive and four-wheel steer was developed by A. L. Lee. Special wheels mounted on king pins on the car permitted all four wheels to be steered. The cable reel was driven by a torque motor to give the cable proper tension during the payout and uniform tension when rewound on the reel. 1940. A Joy shuttle car equipped with trolley poles and a cable reel was developed to operate on a double trolley-wire system.2 This unit was installed at a potash mine of the International Minerals and Chemicals Corporation at Carlsbad, New Mexico. It is believed to have been the first installation of its kind, and the first of shuttle cars for handling material other than coal. 1941. Truck haulage3 was introduced in the Tri State District by the Eagle-Picher Mining and Smelting Company. Storage battery electric trucks were rebuilt to handle a bottom-dump trailer. 1941—Joy shuttle cars were installed in a mine of the United States Gypsum Company, Oakfield, New York. 1943—Joy shuttle cars were installed in several bauxite mines.4,5 1945—Joy shuttle cars installed in a lime-stone mine. Because of the nature of bituminous coal beds trackless equipment has had its greatest application in bituminous coal mining. Usually a shuttle car is filled by a continuous type of loader. In Fig 3 is shown a continuous machine loading coal into a battery-powered shuttle car, 48-in. coal. However, intermittent types of load-

Jan 1, 1949

By W. A. Koehler, M. E. Hinkle

THE oxidation of pyrites and marcasite in coal-mine strata to produce discolored acid mine drainage has long been explained by chemical reactions occurring in three stages: 1. The iron sulphide minerals are oxidized by air in the presence of water to produce a nearly colorless solution of ferrous (iron) sulphate and some sulphuric acid. 2, The ferrous sulphate and part of the sulphuric acid combine with additional oxygen to form ferric (iron) sulphate. 3. The ferric sulphate hydrolyzes to form a reddish-brown precipitate and additional sulphuric acid. Nevertheless, chemical data alone are not sufficient to explain all observed facts. The first stage seems to proceed more slowly in the chemical laboratory than in nature. The second and third stages normally occur to a marked extent within a few days with raw mine water. However, the visible discoloration that characterizes these latter stages will not develop for months if the mine water is sterilized. By means of bacteriological techniques, two organisms have been isolated from acid coal-mine drainage. These are believed to have a part in promoting the chemical reactions summarized above. One organism is considered to be Thio-6aciZZus thiooxidans, which is known to be able to convert elementary sulphur or sodium thiosulphate to sulphuric acid. Its relation to the formation of acid mine drainage has not Yet been established. Apparently it does not Promote the oxidation of ferrous iron compounds in mine drainage to the ferric state. The second organism has not been identified by name but is described as " Gram negative, non-spore-forming rods approximately 0.4 micron wide by 0.8 to 1.0 micron long." A pure culture of this when added to sterile mine water will cause the latter to become amber and develop the typical rusty precipitate. However, it has not been found to convert sulphur compounds to sulphuric acid. Further research is planned to determine whether or not these microorganisms play a significant part in the first stage of oxidation whereby pyrites and marcasite minerals go into solution. Some of the conditions found in abandoned sections of coal mines, such as a reduced Percentage of Oxygen and increased percentage of carboll 'dioxide in the air, as well as the existing temperature and acidity ranges, will be tolerated by and may even be favorable to these organisms. Acid Coal Mine Drainage Acid coal mine drainage has been the concern of coal mine operators, industrialists, sportsmen and public officials for many years. The amount of acid flowing into our streams in the coal-producing areas varies considerably from mine to mine and from

Jan 1, 1949

By A. T. Beckwith

This paper concerns measurements of low-velocity air currents and investigations on mine ventilation by means of chemical smoke. The chemical smoke used is produced without flame and at ordinary mine temperatures, and therefore presents no ignition hazard in gaseous mines. Mining men who have worked in open-light mines are familiar with the use of tobacco smoke in determining the direction of air travel and approximately measuring low-velocity air currents. The use of chemical smoke is merely a refinement on the use of tobacco smoke and the flameless low-temperature source of chemical smoke has the additional advantage that it can be used in gaseous mines. Ventilation smoke apparatus, Fig I, is a simple device for producing dense white smoke. The apparatus as shown consists of a rubber aspirator bulb which is used to force air through a glass "smoke tube" containing a chemical substance that produces a dense white smoke on contact with air. The apparatus was developed by engineers of the U. S. Bureau of Mines.' It is inexpensive, weighs less than 3 oz, is easily carried in a pocket, and requires no skill to operate. Smoke apparatus is invaluable in practical mine ventilation work for: (I) measuring low-velocity air currents, (2) detecting air leakage, (3) observing airflow characteristics. This paper is written to show the merits of the apparatus, and is based upon findings through its extensive use, during the past six years, in mines operated by the Lehigh Navigation Coal Co. Inc. The Apparatus Certain chemicals, such as stannic chloride (SnCl4) and pyrosulphuric acid (H2S2O7) produce "white smoke" when exposed to air. Stannic chloride gives off vapors which on contact with moist air cause the formation of solid hydrates, of which SnCl4.5H20 is the most important. Pyrosulphuric acid decomposes when exposed to air with the evolution of sulphur trioxide (SO3) fumes, which become white upon contacting moisture in the air. A chemical, such as one of the above, is the active substance in a smoke tube. The glass tubes are hermetically sealed during manufacture, and are made ready for use by merely breaking off the tips at the conveniently located file cuts. When the smoke tube is connected to the aspirator, depressing the aspirator bulb forces air into contact with the chemical, and smoke discharges from the open end of the tube. A white solid (a hydrate if stannic chloride is used, or sulphur trioxide if pyrosulphuric acid is used) may occasionally form a cake in the outlet opening of a smoke tube. A small wire such as an ordinary paper clip can be conveniently employed to dislodge the cake should it seal the tube. When the assembled apparatus is not

Jan 1, 1949

By John E. Conley

The slate industry of the United States has shown a marked decline in value of products made annually since the peak year 1925, although there has been moderate improvement over the lean years 1932 to 1934. In 1940, the value of all slate products sold was approximately 5¾ million dollars for a total output of 473,450 short tons. The quantity sold was a little less and the value a great deal lower than the annual averages for the past two decades. Enormous quantities of waste materials result from the quarrying, splitting and milling of slate. Obviously, utilization of such waste material is desirable, not only from the viewpoint of economical operation but also for the purpose of conserving natural resources. One possible use is to produce expanded or puffed lightweight aggregate for use in concretes. Such concretes are strong enough for specific uses, and the advantage of lightness could be obtained in such structures as the walls and roofs of buildings, suspension-bridge roadways and various other applications where weight is a factor. Conceivably, these uses could consume an appreciable annual tonnage. Use of Waste Slates for Making Aggregates The lightweight-aggregate industry has been discussed elsewhere4,5 and need not be covered in detail in this paper. The materials commonly utilized are naturally occurring aggregates such as volcanic cinder, tuff and pumice; by-product materials, such as ordinary cinders and air-cooled slags; and the specially manufactured products, including Haydite, Pottsco, Gravelite, Cel-seal, Superock and Waylite. Slates, however, have not been given the consideration they merit, especially in the United States. In the British Isles, some work has been done3 on certain Welsh slates by the Building Research Station to stimulate the use of these wastes. Requirements for Raw Materials As pointed out by Hughes,4 the lightweight-aggregate industry is segregated in regions adjacent to large cities in order to localize the market and avoid the necessity of long freight haulage. Waste slate from the deposits of eastern Pennsylvania, northern Maryland, and Virginia would meet the basic requirement of ally low-priced structural raw material. One apparent advantage is attained when slate waste, normally discarded, is utilized in the manufacture of a by-product. Mining or quarrying costs usually have been assessed against the main product. Some additional grinding might be desirable, but this operation would be relatively cheap, as most slates grind easily. It is believed that virtually all slates, when properly heated, will expand to some degree. However, types that will expand from 3 to 7 times their original volume are preferred. Fig, I illustratcs the expansion of a Pennsylvania slate. The cube originally

Jan 1, 1942