Search Documents

By Adelaide Ross Smith

Both history and physical examination are unreliable in the diagnosis of silicosis. In some studies 25 per cent of individuals with silicosis have been found to have no symptoms whatever. The positive physical findings that may be produced by this disease include diminished chest expansion, diminished lung resonance, distant and harsh breath sounds. However, many workmen of a short stocky type have diminished chest expansion without any lung disease. In a study of rockdrillers made by the author more than half of the men without silicosis were limited in chest expansion to 2 in. or less instead of the "normal" 6. In a study of stonecutters the average chest expansion in the negative group was found to be only 2.4 inches. Changes found upon physical examination of the lungs themselves are so inconstant as to be of little diagnostic value. In the studies of rockdrillers and stonecutters already referred to, approximately 25 per cent of those with advanced silicosis apparently had normal lungs. The usual functional tests of lung performance are likewise of little value because of marked individual variation. Average vital capacity will be reduced in a group of silicotics below what might be expected in a group of normals, but certain individuals of the former group may have an entirely vital capacity, giving no indication of the underlying presence of silicosis. It follows that the X-ray examination is absolutely indispensable in the diagnosis of this disease. X-ray findings characteristic of silicosis have been described innumerable times. They consist essentially of a mottling of the lung fields due to the presence of fibrous nodules which develop as a reaction to the presence of the irritant silica.

Jan 1, 1934

By B. F. Tillson

There is a dearth of information on the economic threat of silicosis. Even the insurance companies and rating bureaus are in a quandary, and the majority of them avoid any action that will stir up an awakened public consciousness of the serious nature of this industrial hazard. Individual claims for $100,000 are now common in silicosis lawsuits. Because of ('hidden costs," in lowered plant efficiency, the total cost of this disease to industry is probably four times its apparent direct cost. The direct costs vary with the labor policies of the employer and with the labor legislation in force. Direct costs may originate in three ways: (1) voluntary assumption by the employer of medical expenses and loss of earning power of stricken employees; (2) state enforcement of industrial disease compensation acts; and (3) awards or settlements after suits in common law. Examples are offered in the last two classifications. In the Rand, South Africa, compensation laws are in effect and in approximately 20 years prior to 1932 about $65,000,000 has been awarded for silicosis and an additional liability of $34,000,000 incurred, or an average of about t5,000,000 per year. During 1932 silicosis compensation on the Rand was about $6,000,000. No figures are available for the direct capital or operating costs for preventive measures there, nor for the additional "hidden costs." It might be reasonable to assume that silicosis has cost the gold-mining industry of South Africa twenty to twenty-five millions of dollars per year. It is estimated that common-law silicosis claims have, in the last few years, aggregated $50,000,000 in New York State alone and have exceeded $300,000,000 in the United States. Attention is called to the involved nature of the insurance situation for industrial diseases in contrast to accidents. The indeterminant, insidious nature of silicosis makes it particularly difficult to predict necessary insurance premiums and reserves. The serious hazard of this disease was not properly appreciated by either insurance companies or industrialists, so sufficient study has not been given its causation, prevention, detection, treatment, and compensation. Therefore legal difficul-

Jan 1, 1934

By W. B. Daly, A. S. Richardson

The application of artificial refrigeration, or air-conditioning, to the ventilation of deep, hot mines has long been a subject of interest to the operators of such properties. Artificial cooling of the air in theaters, railroad coaches, and various industrial plants has been so successful within recent years that it has been natural to assume that the adoption of similar methods would afford a ready solution to the difficult problem of mine ventilation. It should however, be obvious, that although there may be nothing technically impossible in the application of this process to mine ventilation there is a great economic distinction between the maintenance of a high standard of comfort for a large number of people in a relatively small space such as a theater and the cooling of air to improve working conditions for miners scattered throughout the extensive workings of a large mine. Many methods of air-conditioning have been considered by the management of the Anaconda Copper Mining Co. at various times, but until the development of the process to be described in this paper none has seemed economically practicable. The Ventilating Problem at Butte The main obstacle to satisfactory ventilation in the Butte mines is the normally high temperature of the granite country rock. In the present operating zone, rock temperatures as high as 120' F. have been noted, and in some parts of the district the rate of increase of temperature with depth has ranged as high as 3.5" F. per 100 ft. Other factors, such as the decay of mine timber and the oxidation of sulfide minerals in the ore bodies, contribute to raise the temperature of the air in the working places but, particularly in the development of the mines to greater depth, the naturally high temperature of the rock is of predominant importance. In few other places, probably, are the ordinary ventilating measures more hindered than at Butte. At an operating depth now exceeding 3000 ft., all of the air required for ventilation must pass through timbered shafts which, because of heavy ground, are of small size and offer great resistance to the flow of air. Shaft compartments are rarely more than 4.5 X 5 ft., and the shaft area open to the flow of air usually does not exceed 65 sq. ft.; in only two shafts is the area as great as 85 sq. feet.

Jan 1, 1934

By Leonard Greenburg

The American literature in the field of dust sampling and analysis has been growing rapidly since 1915. Studies made since that time clearly indicate that there are three fundamental factors that determine the production of lung pathology due to dust inhalation. These are the duration of exposure, the chemical and mineralogic nature of the dust and the concentration of the potentially harmful dust. In the estimation of the amount of the potentially hazardous dust there are essentially three problems involved: (I) a determination of the size of the hazardous dust; (2) determination of the most satisfactory apparatus and technique of sampling, and (3) the most satisfactory method of analysis. A complete study of the literature shows that industrial dust varies ill size from ultramicroscopic particles to those larger than lop in diameter and that relatively few particles are found over 5u in diameter. Approximately 10 to 25 per cent are less than 0.811 in diameter and the median size as a rule is found to lie between 1.25 and 1.75 microns. From the point of view of lung pathology the particle sizes of most importance lie between 0.5 and 5u. Of all the instruments for sampling dust the Impinger apparatus is the only one that will sample a larger body of air satisfactorily with small control errors and high efficiency in both low and high concentrations of dust. The Owens apparatus has the advantage of being more portable and somewhat easier to use but it does riot permit of the sampling of large volumes of air. It has a low efficiency in high concentrations of dust and does not permit dust weights to be obtained. From the point of dust-counting technique the author points out that in 1922 considerable experimentation with dark field and oblique illumination resulted in the conclusion that such methods were not readily duplicated from day to day and therefore yielded somewhat erratic results. Changes in the amount of illumination produced variations of several hundred per cent in dust counts obtained with dark ground

Jan 1, 1934

By R. A. Brackett

The most effective means of controlling the dust in the drilling of rock has been found after careful investigation to be collection of this dust at the source. By direct collection, all the dust is collected at the collar of the drill hole and deposited into suitable containers. Equipment for handling this work can be either portable or stationary, depending upon the particular requirements and the application. For most work the portable unit is found most advantageous, and with a capacity capable of handling two drills operating simultaneously. Such a portable unit would consist of a metal cap, or hood, placed against the face of the rock through which the drill steel would be inserted. This hood is connected by a flexible rubber hose to a primary separator, where the bulk of the dust is collected. From here a second length of hose connects to the secondary stage of separation, where the fine particles of dust are collected and which is built in as an integral part of the vacuum producer. Hoods are adapted for vertical, horizontal or stope drilling, and mounted so as to become immediately effective when collaring the hole and remain in place continuously. Such dust collectors can be used with either wet or dry drilling. However, in view of the fact that when drilling dry and using the dust collector, the dust count can be maintained within safe limits, wet drilling becomes unnecessary. Furthermore, it has been found that when using the dust collector not only has the dust hazard been eliminated, but also increased footage can be obtained. Samples taken under a wide variation of conditions indicate that where the dust count required is below five million particles per cubic foot, dust collectors will be required. Opreators, in general, accept the use of this additional equipment favorably, and it is generally felt that such means of collecting the dust will soon be universally adopted. Tests made by the Connecticut Department of Health Bureau of Occupational Diseases show dust counts reduced from 203 million particles to 6.05 million by the use of the dust collector, when drilling dry.

Jan 1, 1934

By Leroy U. Gardner

The human respiratory tract is an apparatus for the interchange of gases between the air and the blood. An important part of it are mechanisms to prevent the apparatus from becoming clogged with dust particles that are inhaled with the air. These mechanisms are adequate to protect the organ against most dusts, but silica and at least one of the silicates, asbestos, are tissue poisons which initiate changes in the connective tissues of the lung, incompatible with function. Silica is concentrated by the phagocytes in contact with the connective tissues of the lymphatic drainage system. An overgrowth of connective tissue occurs which interferes with the function of this system. More dust that may be inhaled can no longer be effectively eliminated from the lung. It accumulates in the functioning part of the organ and excites the formation of characteristic fibrous nodules and bands. These changes seriously impair the respiratory function. The shadows of such changes cast upon an X-ray film of the lung are discussed. The reaction to silica in the lung produces a marked increased susceptibility to tuberculous infection. It can be reproduced and studied in the experimental animal and has been observed repeatedly in human beings. Asbestos dust also causes fibrosis in the lungs but the mechanism of its development is different. The fibrous dust settles along the irregular walls of the terminal bronchioles. In this location it excites the formation of cuffs of scar tissue. This contracts and shuts down the tubes, resulting in a collapse of the air spaces distal to the obstruction. Such a condition in itself is a cause of fibrosis. The two causes, immediate reaction to the dust and collapse of the finer air spaces, bring about a generalized diffuse fibrosis. This reaction is not so regularly associated with increased susceptibility to tuberculosis as with silicosis. The case against sericite as a cause of silicosis has not been proved. Experimentally, sericite-free quartz will produce nodular fibrosis. Silicon carbide and aluminum oxide are quite inert in the normal animals. The former apparently increases susceptibility to tuberculosis in animals but whether the same is true in human beings awaits demonstration.

Jan 1, 1934

By Ralph D. Parker

The Frood mine (Fig. 1) is 2½ miles north of Sudbury, at a general elevation of 1000 ft. above sea level. It includes the original Frood location, which was the No. 3 mine of the Canadian Copper Co., and the adjoining Frood Extension, which until 1929 belonged to the Mond Nickel Co. Mine Openings The mine is operated from two vertical shafts and one underground incline shaft. No. 3, for men, supplies and ore, is a vertical six-compartment shaft in the footwall of the south mining area and extends froin surface to a depth of 3045 ft. No. 4 is a vertical three-compartment shaft, 2500 ft. north of No. 3 and adjacent to the north mining area. It extends from surface to a depth of 3345 ft., and is used exclusively for hoisting ore. No. 5 shaft, inclined at 65' to the horizontal and of three compartments, is near No. 4 and extends from the 2600-ft. level to 77 ft. below the 3100 level. It is used for development below the 2800 level. The ventilation shaft, No. 1, with which this paper is directly concerned, will be described fully in the following pages. Mining Methods The orcbody is laid out in 80-ft. sections at right angles to the gcneral strike and numerically indicated from the southern extremity toward the north. Each section consists of a 45-ft. stope and a 35-ft. pillar, extending the full width of the orebody. Pillars and stopes are superimposed from level to level. The present mining territory is divided into two vertical areas, a north and a south area. Both areas have the same number of stopes on each level, the two areas being separated by 10 sections to be mined later. In a few instances, at the ends of the south area, where the orebody has narrowed, longitudinal stopes are used, of more than the usual 45-ft. width. It will thus be seen that mining operations hare been concentrated in two relatively small areas, offering

Jan 1, 1934

By Henry Seltz, Cyril Wells, Hugh J. MacDonald

Several investigators have measured the heat capacity of cementite, using different methods of attack, but the agreement between the values obtained cannot be considered good. Naeserl has made measurements of "average heat capacities" of iron carbide between 1026" and 85" K., using a water calorimeter. His computed true specific heat at 78.1" K. is 11.22 cal. per gram-formula mass, which, if correct, is much too high for any reasonably accurate extrapolation to 0" K. The cementitc used by Naeser was obtained from a steel containing 0.9 per cent carbon, by electrolytically dissolving out the iron in a neutral bath of ferrous chloride. The cementite remained as a coarse, crystalline, gray powder. Andes2 has measured the specific heat of iron carbide, from 102" to 323" K., as it exists in steel. The specific heats of several slugs of steel of known iron carbide content were determined, and the specific heat of the iron carbide (Fe3C) calculated by plotting specific heat versus percentage of carbon, and extrapolating to pure Fe3C (6.7 per cent C). The heat-capacity values for temperatures below 100" K. were obtained by comparing the temperature-specific heat curve for Fe3C to that of Fe. Since the two were very similar in the range examined experimentally and approach more closely at low temperatures, it was assumed that near the absolute zero the form of the curve for Fe3C would be similar to that of Fe. Andes calculates for the entropy of Fe3 C,S298 = 23.55 e.u. The heat of formation of Fe3C has been studied by several workers. Kelley3 has reviewed these measurements and calculations, and selects those of Roth* and Naeser6 as worthy of most consideration. Roth has given AH = 5400 cal. + 30 per cent as a result of his own and other work. Naeser has determined the heat of formation from Fe and different forms of carbon, and for graphite (0) he finds AH = 5600 cal. Kelley accepts the rounded figure AH = 5500 as the heat of formation at 298.1" K., but this value is quite uncertain.

Jan 1, 1940

By Henry Seltz, Hugh J. MacDonald, Cyril Wells

Several investigators have measured the heat capacity of cementite, using different methods of attack, but the agreement between the values obtained cannot be considered good. Naeserl has made measurements of "average heat capacities" of iron carbide between 1026" and 85" K., using a water calorimeter. His computed true specific heat at 78.1" K. is 11.22 cal. per gram-formula mass, which, if correct, is much too high for any reasonably accurate extrapolation to 0" K. The cementitc used by Naeser was obtained from a steel containing 0.9 per cent carbon, by electrolytically dissolving out the iron in a neutral bath of ferrous chloride. The cementite remained as a coarse, crystalline, gray powder. Andes2 has measured the specific heat of iron carbide, from 102" to 323" K., as it exists in steel. The specific heats of several slugs of steel of known iron carbide content were determined, and the specific heat of the iron carbide (Fe3C) calculated by plotting specific heat versus percentage of carbon, and extrapolating to pure Fe3C (6.7 per cent C). The heat-capacity values for temperatures below 100" K. were obtained by comparing the temperature-specific heat curve for Fe3C to that of Fe. Since the two were very similar in the range examined experimentally and approach more closely at low temperatures, it was assumed that near the absolute zero the form of the curve for Fe3C would be similar to that of Fe. Andes calculates for the entropy of Fe3 C,S298 = 23.55 e.u. The heat of formation of Fe3C has been studied by several workers. Kelley3 has reviewed these measurements and calculations, and selects those of Roth* and Naeser6 as worthy of most consideration. Roth has given AH = 5400 cal. + 30 per cent as a result of his own and other work. Naeser has determined the heat of formation from Fe and different forms of carbon, and for graphite (0) he finds AH = 5600 cal. Kelley accepts the rounded figure AH = 5500 as the heat of formation at 298.1" K., but this value is quite uncertain.

Jan 1, 1940

By D. Van Winkle, C. Zener, H. Nielsen

THe internal friction of metals has been studied frequently at elevated temperatures.1-4 In most cases it rises rapidly with increasing temperature. The notable exceptions are ferromagnetic materials, and lead.2 This paper describes an investigation of the general features of the high-temperature internal friction of 70-30 alpha brass. Experimental Method The internal friction of a metal is a measure of the rate at which it dissipates energy of vibration. The measure adopted here, I/Q, is (I/2p) times the specific damping capacity, a measure commonly used by engineers. In the measurements of this investigation, the stress level was kept so low that the observations were independent of the stress, The general method of making such measurements, and of observing temperature of a specimen during a measurement, has been described.5.6 The driver and detector coils were wound with wire insulated with glass thread, in order to withstand the high temperatures used. In previous work electrical eddy currents in the specimen served as the coupling between the mechanical vibration of the specimen and the electrical circuits of the driver and detector. The high values of the internal friction in the present investigation rendered this coupling insufficient. In order to increase this coupling, pole pieces cut from ordinary telephone diaphragms were attached to the specimen. A mixture of French chalk and water glass proved a satisfactory cement. All measurements were made at the fundamental frequency for transverse vibration, which lay between 600 and goo cycles per second. Specimens The measurements described herein were made upon a single cylindrical rod of brass, kindly furnished by Dr. Cyril Stanley Smith, of the American Brass Co. This rod was the specimen E of the set of alpha-brass rods described in an earlier paper.6 Successively larger grain sizes were obtained by annealing at .successively higher temperatures. A slice was cut off one end after each set of measurements. Grain counts were made on each slice by W. E. Lindlief, of the American Brass Co. Nine fields were viewed on each piece, located as shown in Fig. I. Results are given in Table I. The grain size is defined in the usual way; namely, Grain size = I/n1/2 where n is the mean number of grains per square millimeter. Experimental Results This paper is concerned exclusively with the part of the internal friction that be. comes dominant at high temperatures. It is thus desirable to separate this part of the internal friction from the part that is

Jan 1, 1942

By C. Zener, H. Nielsen, D. Van Winkle

THe internal friction of metals has been studied frequently at elevated temperatures.1-4 In most cases it rises rapidly with increasing temperature. The notable exceptions are ferromagnetic materials, and lead.2 This paper describes an investigation of the general features of the high-temperature internal friction of 70-30 alpha brass. Experimental Method The internal friction of a metal is a measure of the rate at which it dissipates energy of vibration. The measure adopted here, I/Q, is (I/2p) times the specific damping capacity, a measure commonly used by engineers. In the measurements of this investigation, the stress level was kept so low that the observations were independent of the stress, The general method of making such measurements, and of observing temperature of a specimen during a measurement, has been described.5.6 The driver and detector coils were wound with wire insulated with glass thread, in order to withstand the high temperatures used. In previous work electrical eddy currents in the specimen served as the coupling between the mechanical vibration of the specimen and the electrical circuits of the driver and detector. The high values of the internal friction in the present investigation rendered this coupling insufficient. In order to increase this coupling, pole pieces cut from ordinary telephone diaphragms were attached to the specimen. A mixture of French chalk and water glass proved a satisfactory cement. All measurements were made at the fundamental frequency for transverse vibration, which lay between 600 and goo cycles per second. Specimens The measurements described herein were made upon a single cylindrical rod of brass, kindly furnished by Dr. Cyril Stanley Smith, of the American Brass Co. This rod was the specimen E of the set of alpha-brass rods described in an earlier paper.6 Successively larger grain sizes were obtained by annealing at .successively higher temperatures. A slice was cut off one end after each set of measurements. Grain counts were made on each slice by W. E. Lindlief, of the American Brass Co. Nine fields were viewed on each piece, located as shown in Fig. I. Results are given in Table I. The grain size is defined in the usual way; namely, Grain size = I/n1/2 where n is the mean number of grains per square millimeter. Experimental Results This paper is concerned exclusively with the part of the internal friction that be. comes dominant at high temperatures. It is thus desirable to separate this part of the internal friction from the part that is

Jan 1, 1942

By C. F. Park

Hog Mountain is in the north central part of Tallapoosa County, Alabama, about 13 miles northeast from Alexander City. The Hog Mountain Mining and Milling Co. controls 1658 acres of land and is the only company operating in the district. The principal mine workings are in sections 10 and 15, T.24N., R.22E. The region has been visited by geologists many times, has been briefly described in several papers,' and mentioned in many others. No detailed map of the mine or vicinity has been published. The field work for this report was started in March, 1934, as part of the Public Works reemployment program. About a month and a half was spent mapping both the surface and underground geology. The mine owners and operators have cooperated in every way possible to facilitate the work. N. 0. Johnson, the mine engineer, E. W. Ellsworth, J. E. McCoy and J. G. Englebert have acted as assistants for part of the work. The University of Alabama and the State Geologist's office have aided materially by permitting free use of their libraries and laboratory equipment. Geography Hog Mountain forms a conspicuous ridge that rises to a height of a little more than 1000 ft. above sea level, and about 400 to 500 ft. above the adjacent country. The ridge is composed of granitoid intrusive rock and silicified schist that are more resistant to erosion than the surrounding softer schist. The topography of the area around the ridge is gently rolling and is typical of the subdued forms of the deeply eroded Southern

Jan 1, 1935

By C. F. Park

Hog Mountain is in the north central part of Tallapoosa County, Alabama, about 13 miles northeast from Alexander City. The Hog Mountain Mining and Milling Co. controls 1658 acres of land and is the only company operating in the district. The principal mine workings are in sections 10 and 15, T.24N., R.22E. The region has been visited by geologists many times, has been briefly described in several papers,' and mentioned in many others. No detailed map of the mine or vicinity has been published. The field work for this report was started in March, 1934, as part of the Public Works reemployment program. About a month and a half was spent mapping both the surface and underground geology. The mine owners and operators have cooperated in every way possible to facilitate the work. N. 0. Johnson, the mine engineer, E. W. Ellsworth, J. E. McCoy and J. G. Englebert have acted as assistants for part of the work. The University of Alabama and the State Geologist's office have aided materially by permitting free use of their libraries and laboratory equipment. Geography Hog Mountain forms a conspicuous ridge that rises to a height of a little more than 1000 ft. above sea level, and about 400 to 500 ft. above the adjacent country. The ridge is composed of granitoid intrusive rock and silicified schist that are more resistant to erosion than the surrounding softer schist. The topography of the area around the ridge is gently rolling and is typical of the subdued forms of the deeply eroded Southern

Jan 1, 1935

Hog Mountain is in the north central part of Tallapoosa County, Alabama, about 13 miles northeast from Alexander City. The Hog Mountain Mining and Milling Co. controls 1658 acres of land and is the only company operating in the district. The principal mine workings are in sections 10 and 15, T.24N., R.22E. The region has been visited by geologists many times, has been briefly described in several papers,' and mentioned in many others. No detailed map of the mine or vicinity has been published. The field work for this report was started in March, 1934, as part of the Public Works reemployment program. About a month and a half was spent mapping both the surface and underground geology. The mine owners and operators have cooperated in every way possible to facilitate the work. N. 0. Johnson, the mine engineer, E. W. Ellsworth, J. E. McCoy and J. G. Englebert have acted as assistants for part of the work. The University of Alabama and the State Geologist's office have aided materially by permitting free use of their libraries and laboratory equipment. Geography Hog Mountain forms a conspicuous ridge that rises to a height of a little more than 1000 ft. above sea level, and about 400 to 500 ft. above the adjacent country. The ridge is composed of granitoid intrusive rock and silicified schist that are more resistant to erosion than the surrounding softer schist. The topography of the area around the ridge is gently rolling and is typical of the subdued forms of the deeply eroded Southern

Jan 1, 1935

By C. F. Park

Hog Mountain is in the north central part of Tallapoosa County, Alabama, about 13 miles northeast from Alexander City. The Hog Mountain Mining and Milling Co. controls 1658 acres of land and is the only company operating in the district. The principal mine workings are in sections 10 and 15, T.24N., R.22E. The region has been visited by geologists many times, has been briefly described in several papers,' and mentioned in many others. No detailed map of the mine or vicinity has been published. The field work for this report was started in March, 1934, as part of the Public Works reemployment program. About a month and a half was spent mapping both the surface and underground geology. The mine owners and operators have cooperated in every way possible to facilitate the work. N. 0. Johnson, the mine engineer, E. W. Ellsworth, J. E. McCoy and J. G. Englebert have acted as assistants for part of the work. The University of Alabama and the State Geologist's office have aided materially by permitting free use of their libraries and laboratory equipment. Geography Hog Mountain forms a conspicuous ridge that rises to a height of a little more than 1000 ft. above sea level, and about 400 to 500 ft. above the adjacent country. The ridge is composed of granitoid intrusive rock and silicified schist that are more resistant to erosion than the surrounding softer schist. The topography of the area around the ridge is gently rolling and is typical of the subdued forms of the deeply eroded Southern

Jan 1, 1935

By Oscar E. Harder, H. A. Grove

It is now just a quarter of a century since Fred W. Taylor§(23) pub-lished his classical paper On the Art of Cutting Metals, describing his researches in which he, in cooperation with Maunsel White, had developed what is essentially the modern method of heat-treatring high-speed steels. Regarding this research, Dr. Sauveur,(22) in his address on Steel Wizards, Past and Present, at the annual banquet of the American Society for Steel Treating in Philadelphia in 1920 said, "The discovery of high-speed steel, or if you prefer, of the treatment imparting high-speed properties to certain steels by Taylor and Maunsel White I am inclined to consider as our one epoch-making contribution to the metallurgy of steel." It was at about that same time (1900) that Taylor exhibited high-speed steels, heat-treated by the improved process, at the World's Exposition in Paris and attracted much attention by showing that the steels would operate at such feeds and speeds that the tips of the tools were visibly red hot. This observation must have started metallurgists to wondering regarding the relative hardness of the various steels at red-heat temperatures. Considerable work has indeed been done in an effort to measure the hardness of high-speed steels and related materials in the red-heat range, using various methods. The result's, however, have been only partly satisfactory, owing to experimental difficulties. The present investigation had as it's immediate inception an address by J. V. Emmons, of the Cleveland Twist Drill Co., to the Columbus Chapter of the American Society for Steel Treating in 1931, in which he deplored the fact that comparatively little was known with regard to the hardness of high-speed steels at elevated temperatures, in spite

Jan 1, 1933

By Robert C. Berggan

The hot-milling process for reconditioning rock-drill bits is not new. It has been employed by a few mines for years and in the past decade it has been widely adopted, as its advantages have become better known. Because of the extensive commercial development in England and Canada of machines to operate on this principle, general acceptance has been largely in the British possessions and until recently has been chiefly in the field of conventional steel. In the past two years there has been a definite trend toward hot-milling of detachable bits in Canada, but only in the past year has any considerable attempt been made to build special machines for this type of work. Generally a machine designed for conventional steel has been used and special holders employed to manipulate the bit. As early as 1934 at least one operator in the United States had adapted hot-milling to conventional steel with a substantial saving in resharpening costs.1 Several other operators have taken it up but there has been no widespread adoption of the method in this country by users of conventional steel. This may be partly explained by the fact that until recently no American manufacturer produced this equipment and operators have been obliged to build their own hot-millers or import them. Several years ago a few machines were built in Seattle, Washington, and operated in some mines in the northwest, but, for reasons not generally known, the effort was abandoned. The Process Hot-milling performs the function of re-dressing the bit at a forging temperature of about 1650°F., by the removal of metal from the flutes with a milling cutter, followed by a similar cut from the bit gauge. Conventional bits are thus treated following the usual forging operation in a sharpener, and usually in the same heat.

Jan 1, 1940

By Robert C. Berggan

The hot-milling process for reconditioning rock-drill bits is not new. It has been employed by a few mines for years and in the past decade it has been widely adopted, as its advantages have become better known. Because of the extensive commercial development in England and Canada of machines to operate on this principle, general acceptance has been largely in the British possessions and until recently has been chiefly in the field of conventional steel. In the past two years there has been a definite trend toward hot-milling of detachable bits in Canada, but only in the past year has any considerable attempt been made to build special machines for this type of work. Generally a machine designed for conventional steel has been used and special holders employed to manipulate the bit. As early as 1934 at least one operator in the United States had adapted hot-milling to conventional steel with a substantial saving in resharpening costs.1 Several other operators have taken it up but there has been no widespread adoption of the method in this country by users of conventional steel. This may be partly explained by the fact that until recently no American manufacturer produced this equipment and operators have been obliged to build their own hot-millers or import them. Several years ago a few machines were built in Seattle, Washington, and operated in some mines in the northwest, but, for reasons not generally known, the effort was abandoned. The Process Hot-milling performs the function of re-dressing the bit at a forging temperature of about 1650°F., by the removal of metal from the flutes with a milling cutter, followed by a similar cut from the bit gauge. Conventional bits are thus treated following the usual forging operation in a sharpener, and usually in the same heat.

Jan 1, 1940

By J. T. Mackenzie

Henry Marion Howe, in whose memory we are gathered together, was one of the great thinkers who develop from time to time to whom is given the rare gift of synthesis. Analysis is given to few, but synthesis, the ability to show the relation of all parts to each other and thus to give a clear picture of the whole, is reserved for the very few. Analysis can be achieved by honesty, intelligence, and industry, but synthesis is only given to genius. Professor Howe's crowning achievement is the picture of the whole iron-carbon series shown in Fig. I, which places steel, malleable, gray iron, mottled and chilled irons in their proper relation to each other and shows the essential unity of the series. Perhaps his best statement of the case is found on page go of the Metallography of Steel and Cast Iron in these words: " Each member of the gray cast-iron series consists of the metallic matrix approximately equivalent to that member of the steel-white-cast-iron series to which it corresponds in percentage of combined carbon with its continuity broken up—by masses of graphite ..." Apparently he had taken considerable interest in this idea around the turn of the century, for he refers to a discussion at the Franklin Institute in I900 in which he said: "Though many others had probably conceived this relation between the steels and cast irons, it was here enunciated for the first time, so far as I know. It was received with great incredulity." The concept was explained in some detail in a paper on "The Constitution of Cast Iron" presented before the A.S.T.M. in 1902 when Professor Howe was retiring president of that young society. In the discussion Dr. Sauveur stated that he was "very well acquainted with Professor Howe's theory of the constitution of cast iron," and went on to say that while he "shared it to the fullest extent, some foundrymen . . . claim cast iron is a metal entirely different from steel . . . that steel and cast iron have very little in common, and that therefore the knowledge gained in the study of steel is of little or no value in the study of cast iron." Dr. Moldenke, in discussing the same paper, said he had been working on the same theory for 12 years but he laid no claim to publication. Discussing the difference in the micro-structure of the metallic matrix, Professor Howe pointed out that "such minor structural differences are indeed to be expected, because of the difference in the conditions under which these constituents are generated. "One difference in these conditions is that the steel of most micrographs has been either forged or at least treated thermally in such a way as to give a new structure radically different from that which formed during the initial solidification, whereas the cast irons have not. Hence what we see in the steels is a transformation structure, but in the cast irons a solidification structure. By giving the cast

Jan 1, 1944

By J. T. Mackenzie

Henry Marion Howe, in whose memory we are gathered together, was one of the great thinkers who develop from time to time to whom is given the rare gift of synthesis. Analysis is given to few, but synthesis, the ability to show the relation of all parts to each other and thus to give a clear picture of the whole, is reserved for the very few. Analysis can be achieved by honesty, intelligence, and industry, but synthesis is only given to genius. Professor Howe's crowning achievement is the picture of the whole iron-carbon series shown in Fig. I, which places steel, malleable, gray iron, mottled and chilled irons in their proper relation to each other and shows the essential unity of the series. Perhaps his best statement of the case is found on page go of the Metallography of Steel and Cast Iron in these words: " Each member of the gray cast-iron series consists of the metallic matrix approximately equivalent to that member of the steel-white-cast-iron series to which it corresponds in percentage of combined carbon with its continuity broken up—by masses of graphite ..." Apparently he had taken considerable interest in this idea around the turn of the century, for he refers to a discussion at the Franklin Institute in I900 in which he said: "Though many others had probably conceived this relation between the steels and cast irons, it was here enunciated for the first time, so far as I know. It was received with great incredulity." The concept was explained in some detail in a paper on "The Constitution of Cast Iron" presented before the A.S.T.M. in 1902 when Professor Howe was retiring president of that young society. In the discussion Dr. Sauveur stated that he was "very well acquainted with Professor Howe's theory of the constitution of cast iron," and went on to say that while he "shared it to the fullest extent, some foundrymen . . . claim cast iron is a metal entirely different from steel . . . that steel and cast iron have very little in common, and that therefore the knowledge gained in the study of steel is of little or no value in the study of cast iron." Dr. Moldenke, in discussing the same paper, said he had been working on the same theory for 12 years but he laid no claim to publication. Discussing the difference in the micro-structure of the metallic matrix, Professor Howe pointed out that "such minor structural differences are indeed to be expected, because of the difference in the conditions under which these constituents are generated. "One difference in these conditions is that the steel of most micrographs has been either forged or at least treated thermally in such a way as to give a new structure radically different from that which formed during the initial solidification, whereas the cast irons have not. Hence what we see in the steels is a transformation structure, but in the cast irons a solidification structure. By giving the cast

Jan 1, 1944