Search Documents

By T. G. Madgwick, W. Calder

Production of petroleum increased again during 1929, thus maintaining the steady growth inaugurated by the bringing in of Royalite No. 4 in Turner Valley, Alberta, towards the end of 1924, prior to which a decline over a number of years had been experienced. The growth has been confined to the Province of Alberta, the older production in New Brunswick and Ontario showing declines, although in the latter case considerable activity in the search for new gas structures was maintained and during the last six months two wells were brought in, one at Howard in the Trenton at a depth of 1250 ft., giving 5,500,000 cu. ft., and the other at Tilbury in the Guelph or Salina at 750 ft. giving 9,000,000 cubic feet. As has been the case during the past five years, interest in the search for structure and in the following up and development of areas already recognized has centered in Alberta and adjacent portions of Saskatchewan. This was due in the first instance to the striking of wet gas in the Palaeozoic limestone (Madison) of Turner Valley, some 30 miles south of Calgary, in Royalite No. 4 in October, 1924. The bringing in of other wells of similar importance late in 1928 and in the spring of 1929 which extended the productive area 3 miles southwards led to greatly enhanced drilling activity throughout the structure and adjacent areas and in other parts of Alberta. As a result good strikes of heavy crude oil have been recorded during the year at Ribstone, Oyen, Skiff and Coutts, in each case at moderate depths and in sufficient quanitity to justify prolonged testing. The prospects of a satisfactory production of this grade of oil are very encouraging. Actual oil production in the west is still confined to the Province of Alberta and for all grades of oil totaled 997,359 bbl., which compared with previous years shows a gratifying increase. To this increase the naphtha obtained from the wet gas of Turner Valley has proved the principal contributant, heavy crude also showing an improvement, while the light crude, the product of the Cretaceo-Jurassic sands overlying the Paleozoic of Turner Valley, remains unchanged. This is largely owing to operators casing off these sands in their endeavor to reach the limestone, but, there is evidence that in future more attention will be paid to

Jan 1, 1930

By J. Th. Erb

The total crude oil production of these islands, which in 1928 amounted to nearly 5,000,000 metric tons—about 36,500,000 bb1.—has again increased in 1929. The figures for 1929 are as follows: Metric ToNs† North Sumatra........................................ 369,930 South Sumatra........................................ 1,236,510 Java and Ceram....................................... 678,787 Dutch Borneo (including Tarakan)....................... 2,793,326 Sarawak.............................................. 759,700 Total............................................... 5,838.253 †1 metric tor1 = 7.36 bbl. on the average. This production, as far as the Dutch Islands are concerned, is owned partly by the Bataafsche Petroleum Maatschappij, the producing subsidiary of the Royal Dutch Petroleum Concern, and partly by the Kolon-isle Petroleum Maatschappij (Standard Oil Co. of N. J.), while that of the British Protectorate Sarawak belongs to the Anglo-Saxon Petroleum Co., Ltd., of London. The increase in 1929 is due partly to more intensive drilling; the rotary system, which enables drilling to be done more quickly and to greater depths than was possible with the percussion system, has come into more general use. Further, considerable extensions have been made to some of the existing fields and several new pools have been discovered, which contributed in no small degree to the increase in production. Of particular interest is the fact that the ('Niam" (Nederlandsche Indische Aardolie Maatschappij), in which the Dutch Government has a large share and which company in 1928 was producing from only two fields in South Sumatra, has discovered a pool in North Sumatra and, moreover, has struck oil on the island of Poeloe Boenjoe near Tarakan (Eastern Borneo). The deepest well still drilling is in one of the fields of the "Niam" and has reached a depth of 2269 meters (7445 feet). Notwithstanding the tropical c1imate and the dense jungle in which most of the fields are situated, the most modern scientific methods are applied in exploration, in drilling, producing and refining.

Jan 1, 1930

On the map of Europe the shield-shaped area included in the boundaries of Rumania appears too small to constitute a very important factor in the wold's oil production. The country has a total area of 122,000 square miles of territory, about one-fifth of 1 per cent. of the world's surface, from which about 21/2 per cent. of the world's oil was produced in 1929. This relatively small area also constitutes one of the known billion-barrel reserves of the world. Oil has been found in various localities in the foothills of the Carpathian Mountains, extending more than 100 miles in length at their base. It is rather unusual that, while the extent of prospective territory seems to be large, the area of the commercially productive pools is comparatively small. Oil accumulation in Rumania is closely associated with salt stocks. Shows of oil are encountered from the Pliocene down to the Cretaceous. Most of the production, however, comes from the Pliocene, the chief producing sands of which are the Dacic and the Meotic, although some oil is produced from the Levantic and the Pontic. The Meotic as a source of oil was known for many years, but the intensive output from this sand series is a comparatively recent development and accounts in a big measure for the steady increase in Rumanian production. In the early part of the summer of 1929 the Astra-Romano (Royal Dutch) completed a well at Moreni in what is thought by some to be a fourth Meotic sand (a new sand series) at a depth of 5200 ft. with an initial production of 2000 bbl. a day of 41" gravity oil. The development of this new horizon has been somewhat retarded by the disastrous fire which occurred at Romano-Americana's well No. 160 in Moreni, but its discovery adds materially to the future life of the Moreni area, one of the country's oldest fields. Rumania's production for 1929 is estimated at 35,556,000 bbl., a daily average of 97,400 bbl. This compares with the total of 31,542,000 bbl. for the previous year, a daily average of 86,180 bbl., or an increase of 12.73 per cent. Rumania now occupies seventh position in the world's oil picture, it having been replaced as the sixth in importance by the Dutch East Indies in 1929. Table 1 shows a comparison of production by districts and fields.

Jan 1, 1930

By Michael Shaughnessy, O&apos

The outstanding features of the Coloinbian situation for the year 1929 were legal and political. The passage of Law 84 and the promulgation of the Regulatory Decree 150 were recounted in the review for 1928, as was also the Presidential proclamation suspending this law and its accompanying decree until decision could be reached in the suits filed against them before the Supreme Court and the Council of State. Early this year the Minister of Industries, Jose Antonio Montalvo, announced the appointment of a commission of foreign experts to aid in drafting a new petroleum law. He requested all of the foreign experts employed not to consult with the oil company representatives in Bogota, and these experts were therefore shut off from receiving any suggestions from those who had actually operated in the country and knew the conditions under which operations would take place. It was to be expected that the provisions of a law suggested under such circumstances would not meet operating conditions satisfactorily. The specific objections are stated in O'Shaughnessy's South American Oil Reports (April, 1929). An especially qualified commentator observes that one of the curious provisions of the proposed law was the high royalty on gas—5c. per 1000 cu. ft. of gas produced. There was also a provision requiring 20 per cent. of the stock of the company operating in Colombia to be offered for sale to Colombians. The bill failed to pass Congress in the closing hours of the session. The Supreme Court, in the meantime, handed down its decision on Law 84 of the previous year and Regulation 150 covering the enforcement of that law. Contrary to expectation, the majority opinion of the Court practically affirmed the constitutionality of both the law and the regulatory decree, with the exception of Article 20 and parts of Article 21 of the decree which referred specifically to the registration of private properties. At the time the suit was filed against Law 84 and Decree 150 the operation of these measures was suspended by the Executive. Law 84 and its Regulatory Decree 150 still remain suspended as the Council of State has not yet brought in a decision upon the questions raised in the suits instituted by the various companies against the law and decree, and at the moment of this writing it appears unlikely that such a decision will be reached by that body.

Jan 1, 1930

By B. B. Zavoico

Considerable progress has been made during the past year throughout the Russian petroleum industry. Perhaps the most remarkable achievement is the execution of the programs set out by the Central Planning Bureau of the Department of Commerce. These programs have been increased twice during the past operating year, necessitating drilling the richest reserves, instead of developing gradually as originally planned. The fulfillment of the set-out programs during the past few years makes therefore the present five-year plan of considerable importance to the international oil statisticians in approximating actual supply conditions up till 1933. The production of all Russian fields increased by 14,200,000 bbl. as compared with the 1927-1928 operating year, while the next year's program anticipates a further increase of 15,700,000 barrels. It appears therefore that production for 1932-33 will total 187,000,000 bbl., or approximately double that of the operating year just closed. It is also evident that the old fields are counted upon to produce only about 67 per cent. of the total, the new fields, not yet discovered, to furnish the balance of 33 per cent. The Soviet oil leaders therefore are hoping to have new fields discovered and developed by 1932-33. However, as in the past wildcatting

Jan 1, 1930

By Valentin R. Garfias

The world's petroleum production in 1929 is estimated at 1,479,335,-000 bbl., which represents an increase of about 157,000,000 over 1928, as compared with an increase of 61,000,000 bbl. in the previous year. During the present year a more definite policy of conservation has been seriously considered by the foremost executives of the companies controlling the bulk of domestic and foreign production, and the United States Government has taken an active interest in the development of this program. Definite steps have already been taken and the industry is gradually establishing a foundation for closer and more intelligent cooperation. The entire program, however, is still in a formative or experimental stage. Among other salient constructive steps may be mentioned the establishing of tentative agreements of unification in the price of oil products exported from the United States, the putting into effect of a gas conservation law in California, and the marked tendency towards consolidatlions of the various branches of the industry into larger units. The publication of the draft of the proposed petroleum law in Colombia and of the Mexican Labor Law, on the other hand, has created papre-hension and uncertainty. It is confidently expected, however, that these perliminary drafts will be materially modified before the laws arc promulgated, or otherwise they may destroy the interest they are intended to protect. United States Production in the United States, which remained stationary during 1927 and 1928, increased about 105,000,000 bbl., or 11.6 per cent. This increase is due primarily to deeper drilling in the California fields and to the discovery of new pools in Texas and Oklahoma. The progress of the conservation program was marked by the action of the Government in stopping further permits to drill on Government lands; by putting into effect early in September the California Gas Conservation Law, and by

Jan 1, 1930

By Walter Crafts, W. D. Forging, John J. Egan

Although many elements reduce the tendency to porosity in steel castings, manganese, silicon, aluminum, calcium, titanium and zirconium appear to be most generally suitable for the purpose. The manganese and silicon contents are usually maintained in a fairly constant range. Silicon-killed castings often are made to be sound with little or no addition of the stronger degasifiers. In many cases, however, it is more practical to utilize the stronger degasifying elements, aluminum, calcium, titanium and zirconium. Since they greatly modify the composition, shape, and distribution of the nonmetallic inclusions, and thereby the ductility, the strong deoxidizers must be used in such a way as to form the least harmful types of inclusions. As the reasons for failure always to obtain good results have not been obvious, an effort has been made to determine the mechanism of solidification of steels deoxidized to produce certain types of inclusions. Diagrams representsing the mechanism of their formation have been constructed from the appearance of the nonmetallic constituents and have not only illustrated the limiting features of specific deoxidizing treatments with respect to inclusion formation and ductility, but have also indicated a relation between inclusions and resistance to hot tearing. Three different types of deoxidation treatment have been used for obtaining sound castings with relatively high ductility. The first method is to make and cast the steel under such conditions that deoxidation with silicon and a small addition of a strong deoxidizer assures soundness. The effective addition that will promote soundness without causing the formation of intergranular inclusions varies with the furnace practice and composition, but may be limitled to about 0.025 per cent Al, Zr or Ti. Up to 8.10 per cent Ca and 0.15 per cent V are also used for this purpose. The inclusions in these steels are characteristically glassy silicates and round or irregular sulphides. As pointed out by Sims and Lillieqvist,1 the formation of fine intergranular inclusions, which are detrimental to ductility, limits the amount of strong deoxidizers that may be added.

Jan 1, 1940

By John J. Egan, W. D. Forging, Walter Crafts

Although many elements reduce the tendency to porosity in steel castings, manganese, silicon, aluminum, calcium, titanium and zirconium appear to be most generally suitable for the purpose. The manganese and silicon contents are usually maintained in a fairly constant range. Silicon-killed castings often are made to be sound with little or no addition of the stronger degasifiers. In many cases, however, it is more practical to utilize the stronger degasifying elements, aluminum, calcium, titanium and zirconium. Since they greatly modify the composition, shape, and distribution of the nonmetallic inclusions, and thereby the ductility, the strong deoxidizers must be used in such a way as to form the least harmful types of inclusions. As the reasons for failure always to obtain good results have not been obvious, an effort has been made to determine the mechanism of solidification of steels deoxidized to produce certain types of inclusions. Diagrams representsing the mechanism of their formation have been constructed from the appearance of the nonmetallic constituents and have not only illustrated the limiting features of specific deoxidizing treatments with respect to inclusion formation and ductility, but have also indicated a relation between inclusions and resistance to hot tearing. Three different types of deoxidation treatment have been used for obtaining sound castings with relatively high ductility. The first method is to make and cast the steel under such conditions that deoxidation with silicon and a small addition of a strong deoxidizer assures soundness. The effective addition that will promote soundness without causing the formation of intergranular inclusions varies with the furnace practice and composition, but may be limitled to about 0.025 per cent Al, Zr or Ti. Up to 8.10 per cent Ca and 0.15 per cent V are also used for this purpose. The inclusions in these steels are characteristically glassy silicates and round or irregular sulphides. As pointed out by Sims and Lillieqvist,1 the formation of fine intergranular inclusions, which are detrimental to ductility, limits the amount of strong deoxidizers that may be added.

Jan 1, 1940

By M. A. Scheil, S. L. Hoyt

About three years ago eight standard steels were prepared for the cooperative investigation of methods for oxygen analysis, sponsored by the Iron and Steel Division of the American Institute of Mining and Metallurgical Engineers and by the National Bureau of Standards. A preliminary report of the results was made at the annual meeting of the A.I.M.E. in February, 1936. † This report showed the reliability of vacuum-fusion methods and further brought out certain advantages of the fractional vacuum-fusion method. The results obtained by the authors with the latter method will be discussed here, with some comments on the procedure for those who are interested in determinations of gases in steel. Some additional comments are offered on the use of the polarizing microscope for identifying the inclusions in the steel to check and amplify the findings of the fractional vacuum-fusion analysis. For details of the fractional method, see the paper by L. Reeve1. Degassing the Crucible One of the sources of error in vacuum-fusion methods has been the blank gases evolved from the graphite crucible after preliminary out-gassing. We have used 1750" C. as the outgassing temperature. This gives a base pressure at that temperature of less than 0.030 mm. after one hour and of 0.004 mm. on dropping the temperature to 1575" C. At lower extraction temperatures the base pressure is 0.001 mm. at 1050" C., 0.002 mm. at 1170" and 0.003 mm. at 1320' C. Because of the size of our induction coil we are limited to this temperature, although it 'would be advantageous to use 1950" to 2000" C. Hamilton2, after outgassing at 1850" C. for 100 min., was able to reach a base pressure of 0.001 mm. for a temperature of 1700' to 1725" C. This would give a blank corresponding to less than 0.00015 per cent 02 and 0.00005 per cent H2. Chipman and Marshall outgas at 2000" C. for one hour by using a special construction

Jan 1, 1937

By E. R. Parker, R. H. Thielemann

The conventional short-time tensile test provides a reliable means of predicting the sustained load-carrying capacity of steels only when the temperature is such that continuous plastic flow does not occur. At elevated temperatures, stresses considerably less than the short-time rupture value may produce continuous flow, with fracture occurring only after long periods of time. The amount of flow or creep accompanying failure varies for different steels, and depends, to a large extent, on the temperature and the duration of the test. Service records of cracking stills, steam superheaters and high-temperature boilers have shown that brittle fractures sometimes occur with little or no warning. In installations of this type, localized stresses are often encountered, and steels must be capable of withstanding a certain amount of deformation without fracture. The sustained-load rupture test determines the expected life and corresponding ductility of steels at various stresses and temperatures. It also yields additional information regarding the effect of micro-structure and metallurgical stability on the high-temperature properties. Present Status of Sustained-load Rupture Test The sustained-load rupture test conducted at elevated temperatures is not entirely new. Dr. Zay Jeffriesl presented in 1919 the results of a large number of rupture tests made on copper, iron and tungsten. These tests were made with various strain rates and at temperatures ranging from the boiling point of liquid air to 1000° C. At that time he observed the interesting phenomenon characteristic of metals, that a temperature exists below which a metal is ductile and breaks with a transcrystalline fracture (through the grain) and above which the metal is brittle and breaks with an intergranular fracture (through the grain boundaries). He observed that this temperature varied with the testing speed, and that a minimum temperature, slightly above the recrystallization temperature, existed at which the cohesion of the grains themselves was

Jan 1, 1939

By R. H. Thielemann, E. R. Parker

The conventional short-time tensile test provides a reliable means of predicting the sustained load-carrying capacity of steels only when the temperature is such that continuous plastic flow does not occur. At elevated temperatures, stresses considerably less than the short-time rupture value may produce continuous flow, with fracture occurring only after long periods of time. The amount of flow or creep accompanying failure varies for different steels, and depends, to a large extent, on the temperature and the duration of the test. Service records of cracking stills, steam superheaters and high-temperature boilers have shown that brittle fractures sometimes occur with little or no warning. In installations of this type, localized stresses are often encountered, and steels must be capable of withstanding a certain amount of deformation without fracture. The sustained-load rupture test determines the expected life and corresponding ductility of steels at various stresses and temperatures. It also yields additional information regarding the effect of micro-structure and metallurgical stability on the high-temperature properties. Present Status of Sustained-load Rupture Test The sustained-load rupture test conducted at elevated temperatures is not entirely new. Dr. Zay Jeffriesl presented in 1919 the results of a large number of rupture tests made on copper, iron and tungsten. These tests were made with various strain rates and at temperatures ranging from the boiling point of liquid air to 1000° C. At that time he observed the interesting phenomenon characteristic of metals, that a temperature exists below which a metal is ductile and breaks with a transcrystalline fracture (through the grain) and above which the metal is brittle and breaks with an intergranular fracture (through the grain boundaries). He observed that this temperature varied with the testing speed, and that a minimum temperature, slightly above the recrystallization temperature, existed at which the cohesion of the grains themselves was

Jan 1, 1939

By Harry Seltz, J. C. DeHaven

InteRmetallic compounds are formed in many binary metal systems. Some compounds are stable to their melting points, and others decompose at lower transition temperatures. Even those of the first class are dissociated in the liquid state, as indicated by the continuous form of their solubility curves at their melting points1. While the lattice structures of some of these compounds have been determined, their thermodynamic properties have not been investigated. In this paper is described the determination of the free energy and heat of formation of the compound CdSb, which is of the first class mentioned above, melting congruently at 455' C. This compound shows a rhombic structure, and the lengths of the edges of the elementary cell containing four molecules are: a = 6.52, b = 8.60, c = 4.16 A.' There are three possible methods of determining the free energy of formation of a compound of this type. The first method, applying the third law of thermodynamics, requires the measurement of its heat capacity preferably to liquid hydrogen temperatures, and a calorimetric determination of its heat of formation. The second method involves the study of the equilibrium of the compound in some gas reaction, such as: CdSb + CO² = CdO + CO + Sb From the known free energies of formation of CdO, CO² and CO the free energy of formation of CdSb could be calculated. The third method measures the electromotive force of a galvanic cell in which the cell reaction is the reversible formation of the compound from the elements. The first method is generally applicable, but requires elaborate experimental equipment. The second method can not be used for compounds melting at low temperatures, owing to the difficulty in establishing equilibrium. The electromotive force method, therefore, seemed to offer

Jan 1, 1935

By J. C. DeHaven, Harry Seltz

InteRmetallic compounds are formed in many binary metal systems. Some compounds are stable to their melting points, and others decompose at lower transition temperatures. Even those of the first class are dissociated in the liquid state, as indicated by the continuous form of their solubility curves at their melting points1. While the lattice structures of some of these compounds have been determined, their thermodynamic properties have not been investigated. In this paper is described the determination of the free energy and heat of formation of the compound CdSb, which is of the first class mentioned above, melting congruently at 455' C. This compound shows a rhombic structure, and the lengths of the edges of the elementary cell containing four molecules are: a = 6.52, b = 8.60, c = 4.16 A.' There are three possible methods of determining the free energy of formation of a compound of this type. The first method, applying the third law of thermodynamics, requires the measurement of its heat capacity preferably to liquid hydrogen temperatures, and a calorimetric determination of its heat of formation. The second method involves the study of the equilibrium of the compound in some gas reaction, such as: CdSb + CO² = CdO + CO + Sb From the known free energies of formation of CdO, CO² and CO the free energy of formation of CdSb could be calculated. The third method measures the electromotive force of a galvanic cell in which the cell reaction is the reversible formation of the compound from the elements. The first method is generally applicable, but requires elaborate experimental equipment. The second method can not be used for compounds melting at low temperatures, owing to the difficulty in establishing equilibrium. The electromotive force method, therefore, seemed to offer

Jan 1, 1935

By Alfred Boyles

"Heredity"1 in cast iron has been a subject of much discussion. Numerous experimenters have found that the properties of gray iron may vary greatly without corresponding variations in composition or thermal treatment. The main structural difference in such cases is in the size and distribution of the graphite flakes and the explanations given usually attribute this difference to some chemical element not shown by ordinary analysis or to some physical factor, such as inclusions in the melt. It cannot be said that any of these theories is completely satisfactory. Much remains to be learned about cast iron and for this reason a study of the material was undertaken as a part of the program of fundamental research at Battelle Memorial Institute. A review of the literature indicated that very little systematic work had been done on the mechanism of freezing in cast iron. The experiments described below are largely concerned with that problem. Normal and "Dendritic" Cast Iron As examples of variation in type of structure, photomicrographs of two test bars of cast iron are shown (Figs. 1 and 2) and the composition and properties are given in Table 1. Both are common, unalloyed gray iron. Test bar No. 13 has normal graphite flakes while No. 49 has very fine, lacy graphite arranged in a dendritic pattern, the matrix in both being pearlite. These two types of cast iron are well known to foundry-men and need no detailed description.

Jan 1, 1937

By Henry Mulryan

Diatoms are microscopic aquatic plants of the order Bacillariaceae. They are unicellular plants with skelctons made up of amorphous opaline silica. The skeletons show highly ornate, complicated geometrical designs. Diatoms live in water virtually everywhere. They are found in clean sea water, brackish water, and fresh-water lakes and ponds. When conditions are right, diatoms propagate by subdivision in huge numbers. Alkalinity, temperature, and the presence of high concentrations of silica in the water largely control diatom life. When the diatoms die the skeletons drop to the bottom of their habitat to form oozes of varying thicknesses. Diatomites Diatomite, or diatomaceous earth, is composed essentially of the siliceous remains of the diatoms, although other organic skeletons are also present, especially in sea-water deposits where radiolaria, sponges and silico-flagellates are common. Impurities are generally carbonaceous material, fine-grained silt, volcanic ash and dust, and occasional coarse grains of sand. Diatomites are marine, brackish, or fresh-water, depending upon types of diatoms and their method of deposition. Diatoms More than 8000 species of diatoms have been named and classified. Some are definitely classified as to their habitat; some are so well recognized as to their living conditions that they can be stated to be diagnostic types, and when encountered in a deposit determine the origin of the deposit. Some of the commoner types of diatoms found in the freshwater diatomites on the Pacific Coast are: Cymbella lanceolata Agardh Fragilaria virescens Ralfs Encyonema prostratum Ralfs Diatoma vulgare Dory Surirella biseriata Brebison Eunotia major Ehrenberg Amphipleura pellucida Kützing Stictodiscus niagarac Ehrenberg Gomphonema geminatum Lynberg Melosira granulata Ehrenberg Epithemia turgida Kützing

Jan 1, 1942

By Henry Mulryan

Diatoms are microscopic aquatic plants of the order Bacillariaceae. They are unicellular plants with skelctons made up of amorphous opaline silica. The skeletons show highly ornate, complicated geometrical designs. Diatoms live in water virtually everywhere. They are found in clean sea water, brackish water, and fresh-water lakes and ponds. When conditions are right, diatoms propagate by subdivision in huge numbers. Alkalinity, temperature, and the presence of high concentrations of silica in the water largely control diatom life. When the diatoms die the skeletons drop to the bottom of their habitat to form oozes of varying thicknesses. Diatomites Diatomite, or diatomaceous earth, is composed essentially of the siliceous remains of the diatoms, although other organic skeletons are also present, especially in sea-water deposits where radiolaria, sponges and silico-flagellates are common. Impurities are generally carbonaceous material, fine-grained silt, volcanic ash and dust, and occasional coarse grains of sand. Diatomites are marine, brackish, or fresh-water, depending upon types of diatoms and their method of deposition. Diatoms More than 8000 species of diatoms have been named and classified. Some are definitely classified as to their habitat; some are so well recognized as to their living conditions that they can be stated to be diagnostic types, and when encountered in a deposit determine the origin of the deposit. Some of the commoner types of diatoms found in the freshwater diatomites on the Pacific Coast are: Cymbella lanceolata Agardh Fragilaria virescens Ralfs Encyonema prostratum Ralfs Diatoma vulgare Dory Surirella biseriata Brebison Eunotia major Ehrenberg Amphipleura pellucida Kützing Stictodiscus niagarac Ehrenberg Gomphonema geminatum Lynberg Melosira granulata Ehrenberg Epithemia turgida Kützing

Jan 1, 1942

By David R. Mitchell, H. E. Oehler, Henry Emmett Gross

The production of fluorspar is one of the smaller nonmetallic industries in the United States with a capital investment—about $10,000,000. Shipments from United States mines1 in 1936 totaled 176,231 short tons valued at $3,111,268, an average price of $17.65 per ton. The United States produces about 40 per cent of the world's fluorspar, of which about 90 per cent comes from the Illinois and Kentucky deposits along the Ohio River.2 Further detailed information on the fluorspar industry in the United States is given by Hatmaker and Davis.28 The concentration of the coarser sizes presents relatively little difficulty, good recoveries being obtained with jigs and tables. However, sizes smaller than about 10 mesh cannot be successfully treated by ordinary gravity separation methods and so have been accumulating as

Jan 1, 1939

By Henry Emmett Gross, David R. Mitchell, H. E. Oehler

The production of fluorspar is one of the smaller nonmetallic industries in the United States with a capital investment—about $10,000,000. Shipments from United States mines1 in 1936 totaled 176,231 short tons valued at $3,111,268, an average price of $17.65 per ton. The United States produces about 40 per cent of the world's fluorspar, of which about 90 per cent comes from the Illinois and Kentucky deposits along the Ohio River.2 Further detailed information on the fluorspar industry in the United States is given by Hatmaker and Davis.28 The concentration of the coarser sizes presents relatively little difficulty, good recoveries being obtained with jigs and tables. However, sizes smaller than about 10 mesh cannot be successfully treated by ordinary gravity separation methods and so have been accumulating as

Jan 1, 1939

By A. W. Gauger

It is with some trepidation that I approach my subject, for I know that I shall at once incur the suspicion of the mechanical engineer, with his concern for boiler tests and efficiencies; of the mining engineer, with his mechanization problems; and of the chemical engineer with his unit processes. Nevertheless, it must be recognized that the technology of fuels, the systematic body of knowledge relating to the production, processing and utilization of mineral fuels, has grown to such proportions and involves so many widely diverse applications of fundamental science and engineering that it behooves us to stop and consider just what its status is in relation to other technologies, as well as in relation to the present and future needs of the social order. The time has come when technologists, applied scientists and engineers must consider the possible effects that their achievements may have on Society. The development of a machine to - -replace -several hundred men is a fine achievement when considered solely from the point of view of creative endeavor. But what of the men who are displaced by the machine! Does not the responsibility for the development of this machine embrace as well the consequences of obsolescence and technological unemployment resulting from such development? I believe that it does and that we must recognize this fact in our practice of engineering and tech- nology as well as in the training of future engineers and technologists. Magnitude of the Fuels Industry Fuel technology is the body of knowledge that relates to the mineral fuels. The fuels industry is by far the most important of all Our mineral industries. The chart in Fig. I, reprinted from U. S. Bureau of Mines Information Circular No. 6643, indicates the compartive values of metals, fuels and other nonmetallic minerals for the year 1929. Of the grand total of 13¼ billions of dollars in value of minerals at the mines, the mineral fuels contributed 48 per cent. Coal, with 34.4 Per cent, exceeded the value of any other single mineral. In fact, the value of the production of the Pennsylvania anthracite mines alone anand exceeds the value of the gold production of the entire world. Petroleum and natural gas in 1929 contributed 14.3 per cent and 3.3 per cent, respectively, of the total value of world mineral production. So much for the world picture; let us now look at the situation in the United States. Over the 60-year period 1880 to '939, $46,409,727,000 of metal1ic products, $80,788,852,000 of fuels (coal, petroleum, natural gas, natural gasoline) and $27,871,-ooo,ooo of nonmetallic minerals other than fuels were produced. The mineral fuels have contributed 52.7 per cent of the entire mineral wealth produced over this period that has seen such tremendous industrial development in our Our As a matter of fact, our present industrial civilization has been made possible through the use of the

Jan 1, 1942

By A. W. Gauger

It is with some trepidation that I approach my subject, for I know that I shall at once incur the suspicion of the mechanical engineer, with his concern for boiler tests and efficiencies; of the mining engineer, with his mechanization problems; and of the chemical engineer with his unit processes. Nevertheless, it must be recognized that the technology of fuels, the systematic body of knowledge relating to the production, processing and utilization of mineral fuels, has grown to such proportions and involves so many widely diverse applications of fundamental science and engineering that it behooves us to stop and consider just what its status is in relation to other technologies, as well as in relation to the present and future needs of the social order. The time has come when technologists, applied scientists and engineers must consider the possible effects that their achievements may have on Society. The development of a machine to - -replace -several hundred men is a fine achievement when considered solely from the point of view of creative endeavor. But what of the men who are displaced by the machine! Does not the responsibility for the development of this machine embrace as well the consequences of obsolescence and technological unemployment resulting from such development? I believe that it does and that we must recognize this fact in our practice of engineering and tech- nology as well as in the training of future engineers and technologists. Magnitude of the Fuels Industry Fuel technology is the body of knowledge that relates to the mineral fuels. The fuels industry is by far the most important of all Our mineral industries. The chart in Fig. I, reprinted from U. S. Bureau of Mines Information Circular No. 6643, indicates the compartive values of metals, fuels and other nonmetallic minerals for the year 1929. Of the grand total of 13¼ billions of dollars in value of minerals at the mines, the mineral fuels contributed 48 per cent. Coal, with 34.4 Per cent, exceeded the value of any other single mineral. In fact, the value of the production of the Pennsylvania anthracite mines alone anand exceeds the value of the gold production of the entire world. Petroleum and natural gas in 1929 contributed 14.3 per cent and 3.3 per cent, respectively, of the total value of world mineral production. So much for the world picture; let us now look at the situation in the United States. Over the 60-year period 1880 to '939, $46,409,727,000 of metal1ic products, $80,788,852,000 of fuels (coal, petroleum, natural gas, natural gasoline) and $27,871,-ooo,ooo of nonmetallic minerals other than fuels were produced. The mineral fuels have contributed 52.7 per cent of the entire mineral wealth produced over this period that has seen such tremendous industrial development in our Our As a matter of fact, our present industrial civilization has been made possible through the use of the

Jan 1, 1942