Search Documents

By L. Max Scott

[INTRODUCTION] The significance of gamma exposure to uranium miners has been recognized only in the last few years. Most ore deposits which have been underground mined, were 1% or less U308. Full-time mining of this grade ore can result in exposure exceeding 1 Rem per year. Several companies in Saskatchewan are planning to mine recently discovered ore bodies which contain ore pods in excess of 10% U308. The purpose of this paper is to present dose data which can be used to estimate gamma exposure from high-grade ore deposits, and to present mining techniques which will minimize miner exposure. [Dose Estimates] When one has a point source of radiation, the conventional laws of isotropic emission and the fall of dose with square of the distance, make dose calculations relatively easy. However, if one has an area source of infinite thickness, the assumption must be made that a uniform gamma flux is being emitted from all faces of the source (Figure 1). Dose from gamma emission would fall off only due to air attenuation up to such a distance at which the source can be considered to be a point source (usually 10 times the largest dimension of the source). For short distances, such as to the cab of ore-moving equipment, the dose reduction would be negligible. Assumptions: 1) Radium and gamma-emitting daughters are in secular equilibrium with uranium. 2) All gamma radiation is emitted from radium and its daughters. 3) Average gamma energy of 0.8 MeV. 4) Uranium ore has a linear attenuation coefficient of 0.212 cm-1, similar to that of Si02(sand). 5) Uranium ore density of 3.0 gm/cm3. 6) One curie of radium emits 6.84 x 1010 photon/sec(l). 7) One percent uranium ore contains 1 x 10-8 Ci/cm3 of radium. 8) Each MeV of 0.8 MeV photon results in a dose of 2.10[ ]10-3 mRem/hr. per MeV/cm2 -sec. 1) 9) Minimum ore depth 100 cm. 10) Linear attenuation coefficient instant for radium gamma of 0.374 cm -1 [ ] The photon flux from a radioactive slab is computed as follows: [Flux = photon/cm3 3(1) 2u S] [where, us is the linear absorption coefficient of s the source (uranium ore).] Thus, 1% uranium ore, in the form of an infinite slab, emits 1613 photon/cm2-sec, which results in a dose rate of 2.71 mRem/hr. Since the dose from an infinite slab is the same as a dose from an infinite radius right circular cylinder, the only correction needed from the above dose rate is for finite radius and point of dose above the end of the cylinder (Figure 2) [Dose = mRem/hr. {E2(bl) - E2(b3) - [(E2(b1sec[E] -E2(b3sec[E]]cos[O](1)]

Jan 1, 1981

By E. O. Binyone

"https://www.youtube.com/watch?v=PBPyGXjlBHIhttps://www.youtube.com/watch?v=3AbtiKOYg7Y&feature=push-fr&attr_tag=uKtVW3yq2ZngptnE%3A6https://www.youtube.com/watch?v=PR2THayf-N8https://www.youtube.com/watch?v=mF-BXiWocqIhttps://www.youtube.com/watch?v=TuesIw-OZA4https://www.youtube.com/watch?v=v2HP7sTIZgEhttps://www.youtube.com/watch?v=v2HP7sTIZgEINTRODUCTIONIn 1937 the Eureka Corporation, Ltd., of Canada obtained a lease on the mining property of the Richmond-Euroka Mining Co. in the Eureka mining district, Eureka County, Nevada. In 1910 the Richmond-Eureka Co. suspended all operations except small-scale leasing, but company and other geologists contended that the El Dorado dolomite would also carry ore in its continuation from fault block north and northeast of the productive old working. The company began to explore the fault block in 1923 by diamond drilling from the,900 level of the Locan shaft, but for various reasons the hole was drilled to a depth of only 2 feet and was then abandoned. Eureka Corporation, Ltd., planned an extensive diamond-drilling program, which included four deep diamond-drill holes, one designated ""A"" fig. if it is to be drilled from the surfaced, and three designated ""E"", ""C"" and ""D"" figs land to be drilled from the 900 level of the Locan shaft. Of these only B and C were completed by the company. Hole C was a contribution,of the hole started by the, started by the Richmond Eureka Co. The site for hole D (figs. 1 and 2) was prepared, but the hole was not drilled. Both B and C holes penetrated sulfide ore carrying good percentages of zinc, lead, gold, and silver. The ore bodies were 40 feet thick and were found approximately 1,400 feet below the 900 level of Locan shaft.On the basis of the very favorable results obtained from the drilling program, the Eureka Corporation planned extensive development of the property and in 1942 commenced sinking the Fad shaft (figs. 1 and 2). The shortage of equipment and materials brought on by the war and difficulties with water in the shaft greatly hindered progress. However, early in 1943 the Eureka Cor¬poration, Ltd., of Canada submitted to the War Production Board a proposal for developing the mine and milling 500 tons of zinc-lead ore a day. The proposal involved an expenditure of $2,890,750."

Dec 1, 1946

By James S. Redpath

"AbstractThis paper is an attempt. to outline the present status of underground mining contracting in Canada, and to present certain facts concerning the writing and administration of underground mining contracts which, hopefully, may be useful to those intending to engage a mining contractor . The paper is based on the author' s experience as a contractor and also as a consulting engineer advising others in the purchase of contractors' services.HistoryIN THE early days of mining contracting in Canada, the contractor was primarily a labour contractor. He was expected to bring a good crew of men that normally followed him, and to perform certain work under his own direct supervision. The owner usually looked after all other details including financing, payrolls, withholding taxes, etc , computing and paying the contractor his profit. In the pre-World-War II years, most work was done on this basis.Over the years, the contractor was called on to supply more in the way of services, and the present-day situation evolved.Labour contracts are still used, but now the contractor is expected to carry out his own administration. Most contracts now call for the supply of special tooling required to do the work. In most cases, some, if not all, supplies are the contractor 's responsibility and , in a growing number of cases, the contractor is responsible for such items as design and surveying. The ultimate in this direction is the execution of projects on a turnkey basis. Under this system , the contractor carries the project to a stage where it is turned over fully operational to the owner."

Jan 1, 1977

By Irina Chernyshova, Erik Larsen, Hanumantha Rao Kota, Vladislav Slabov, Garima Jain

The separation of fine mineral particles, especially using environmentally friendly approaches, is one of the main problems in the processing of low-grade ores and the re-processing of mining tailings. This work assesses the potential of biosurfactants as collectors in the flotation of ultrafine (smaller than 20 μm) particles of hematite and malachite. As biosurfactants, we test acetylated acidic (ac-ASL) and lactonic sophorolipids (ac-LSL). In addition, n-dodecyl-β-D-maltoside (DDM) is used as a model non-ionic alkyl disaccharide surfactant, and sodium oleate (NaOl) is used as a reference. The biosurfactants are characterized using surface tension and foam analysis. The interaction of the minerals with the surfactants is characterized using zeta potential, solubility, and single-mineral flotation. The collecting properties of the surfactants are compared for the ultrafine (− 20 μm) and coarser (38–90 μm) particle size in the two-mineral flotation of hematite and malachite against quartz. The ultrafine particle size improves the grade in the oleate flotation of hematite, as well as the grades in the DDM flotation of hematite and malachite, which is explained by the weak interactions of the metal oxides with fatty acids and DDM. At the same time, the flotation with ac-LSL and ac-ASL is highly tolerant to the ultrafine particle size. These results indicate that biosurfactants are an interesting alternative to conventional petroleum-based surfactants in the flotation of Fe and Cu oxides. Moreover, a proper selection of surfactants can help combat the problem of fines.

Feb 23, 2023

By Jan C. Still

The Haines-Klukwan-Porcupine subarea of the Juneau Mining District (JMD) is located in the northern portion of the JMD and consists of the land between the Alaska-British Columbia boundary, the Chilkoot Valley, Glacier Bay National Park boundary, and extending south to the Davidson Glacier and the Chilkat Peninsula and Islands (fig A-I). This area was studied as part of the larger JMD study in a cooperative effort between the Alaska Division of Geological and Geophysical Surveys (ADGGS) and the Bureau during 1985 to 1988. Prior to this, during 1984, the ADGGS and the Bureau cooperated in a study of the Porcupine mining area and during 1981 to 1983 conducted separate studies in the area. Field work was conducted by foot, boat, truck, and helicopter. Figure A-I shows the Haines-Klukwan-Porcupine sub-area and shows the areas covered by previous Bureau and ADGGS studies. PHYSIOGRAPHY AND CLIMATE The physiography of the subarea ranges from gentle to rugged. Glaciers formed the major features in the sub-area and left "U" shaped steep walled valleys and rugged mountains. The Chilkat, Chilkoot, Klehini, Tsirku, and Takhin are the major rivers in the subarea. The higher mountains are glacier clad and some valleys still harbor glaciers that reach the valley floors. Lush forests and dense brush predominate up to timberline at about the 2,000-foot elevation. Low point in the subarea is at sea level in the area around Haines while the high point is 7,434 feet at: Mount Henry Clay in the Porcupine mining area.

Jan 1, 2012

By Patterson B. G

The small party of mining men who formed the original Mount Morgan Syndicate in 1882, commenced operations on the top of the mountain with what were practically nothing more than small hillside quarries, It was not until 1891 that underground stoping began, and open-cut mining therefore commenced with the commencement of operations. This hillside quarrying, however, seems to have been quite haphazard and unsystematic ; there is no trace or sign of any properly devised mining scheme. This can be seen plainly enough from an examination of old mine plans; for in less than five years after stoping was; adopted, the open-cut was down into the stoped-out ground. The following table, prepared from these old plans, shows the downward trend of the excavation in the past fiftyseven years:-

Jan 1, 1939

By Fabiana da Silva Santos

O presente estudo fez uso de uma liga de NiTi, rica em Ni, elaborada em um forno de fusão por indução a vácuo - VIM e posteriormente refundida em fornos de arco elétrico com eletrodo não consumível de tungstênio – VAR. Com base nos resultados de Calorimetria Diferencial de Varredura (DSC), Difração de Raios-X (DRX) e Microscopia Eletrônica de Varredura (MEV) / Espectroscopia de Energia Dispersiva de Raios-X (EDS), foi possível observar a heterogeneidade composicional/ típica de fundido por processo convencionais, as inclusões de TiC e Ti4Ni2O provenientes da fusão no forno VIM, e o refinamento microestrutural e manutenção da sua composição original com uso de cadinho de cobre e câmara/atmosfera dos fornos VAR.

Oct 30, 2017

By J. R. Thoenen

Up to 1914 almost all of the world's supply of potash came from Germany and Alsace. With the cessation of shipments from Germany during the World War the importance of a domestic supply was evident, During the past 15 years the United States has been working toward the establishment of a domestic potash industry which would end foreign dominance in this commodity. The Federal government has taken an active part in this program. As its share in the work, the Bureau of Mines has ascertained the potash resources in certain districts through core drilling and has engaged in a comprehensive program of research on the extraction of potash from its various minerals. Until the passage of the Winter bill (H. R. 496) by Congress in 1928 the Bureau of Mines had not been able to give any consideration to the western ores, wyomingite (leucite) and alunite. With the Passage of this bill, however, the ray was opened for the extension of the potash studies to cover these materials.

Jan 1, 1932

By D. C. Sisti

A technical evaluation of actual performance of the preparation facilities at Beaver Consolidated Coal Co.'s Stinson plant is presented, with special emphasis on sulfur reduction in 1-1/2 x 3/8 in., 3/8 in. x 28 mesh, and 28 mesh x 0 size fractions. Evaluation of the heavy medium section of the plant and the treatment of the 28 mesh x 0 coal is included. Design criteria considered for sizing and selection of equipment required to process 1-3/4 million tpy of raw coal on coals of divergent washability characteristics are summarized.

Jan 1, 1976

By T. T. Tomimatsu

This? Bureau of Mines paper discusses the corporate structure dynamics, methods of financing, and financial assessment approaches that should be utilized to evaluate the economic health of the coal industry. It suggests rates of return and other measures of corporate economies necessary to attract capital required to finance emerging coal demand, plus impact of coal sales to total revenues. The study illuminates the activities of 30 selected coal-producing companies, including their subsidiaries or affiliates, that were responsible for approximately 60 percent of the total U.S. production in 1974. The selected firms are not all primary coal producers; many of the larger producer's are classified by the financial institutions as petroleum, metal, and steel producers, public utilities, or chemical industries. The bituminous coal industry is highly competitive as to price, service, and quality of pronuct and is subject to competition from other noncoal energy sources. The top 15 bituminous coal-producing companies mined about 46.6 per-cent of the Nation's total production in 1974, and the balance of approximately 3,885 companies were responsible for the rest of the production. Thus, the U.S. bituminous coal industry is not an oligopoly. Today, about 65 percent of the Nation's total coal production is consumed by electric power utilities and 26 percent by steel, space heating, and other industries; the balance of 9 percent is exported.

Jan 1, 1976

By Juan J. Monsalve, Mario Karfakis, AMAN SONI, Nino Ripepi, Jim Hazzard

Pillar collapses are events that due to their severe consequences can be classified as high risk. The design of pillars in underground room-and-pillar operations should migrate to risk-based design approaches. The authors of this work proposed a risk-based pillar design methodology that integrates stochastic discrete element modeling for pillar strength estimation, and stochastic finite volume modeling (FVM) for stress estimation. This paper focuses on the stochastic FVM component for stress estimation. The mining and geomechanical aspects of a case study mine (CSM) are described and pillar stresses are estimated by using three approaches: (1) analytical solutions, (2) 2D finite element modeling, and (3) 3D finite volume modeling. This operation extracts a 30° dipping deposit, which makes current underground stone mine design guidelines inapplicable for this CSM. This work compares results from each stress estimation approach and discusses uses the point estimate method as a simplified stochastic approach to evaluate the effect of rock mass elastic properties variability on pillar stress distribution. Results from this work show that the three estimation approaches lead to different estimations, possibly, due to the wide range of assumptions each estimation approach considers. It was also determined that the horizontal to vertical stress ratio has a significant impact on pillar stress magnitude. Therefore, it is recommended to perform in situ stress measurements, or assume worst-case-scenario values to account and reduce uncertainty due to this parameter. The stochastic stress estimation approach used in this paper provides results that can integrate a risk-based pillar design framework.

Sep 24, 2022

By Wm. O. Vanderburg

This paper describing the milling methods at the Hughesville concentrator of the St. Joseph Lead Co., Hughesville, Mont., is one of a series of similar papers being prepared by the U. S. Bureau of Mines on practices at the various mills in the United States. The writer expresses his thanks for the courtesies extended by the officials of the company while visiting the property and acknowledges the assistance and helpful suggestions given by R. H. Willcomb, general manager, and Carl Martin, mill superintendent, of the Hughesville Division f the St. Joseph Lead Co.; and E. D. Gardner, supervising engineer, U. S. Bureau f Mines, Southwest Experiment Station, Tucson, Ariz., in gathering and compiling the data herein presented.

Jan 1, 1931

Industrial minerals by definition are minerals used as part of an industrial process and usually are one of a number of components, eg finely ground Limestone is an extender in the manufacture of paint. They are normally non-metallic and non-fuel, but like all generalisations there are a number of exceptions. Take rutile û a source of titanium, a metal and also the raw material in the manufacture of titanium dioxide pigment. Industrial minerals under this general definition include construction and agricultural minerals. They are included in the same grouping, principally because their sources are similar and in many cases the raw material, example limestone, can be multi-functional. Calcium carbonate raw materials such as limestone, are used in a wide range of applications from industry as an inert filler, to agriculture as a 'lime' source and to construction and as an important component in the manufacture of cement. As far as this paper is concerned I will avoid discussing the agricultural or construction applications, including burnt lime production.

Jan 1, 1985

By Adam Chrzanowski, Eugene E. Derenyi, Peter Wilson

"The rapid growth of the mining industry in Canada necessitates a reevaluation of existing mining surveying techniques and the development of new methods. In this connection, the Department of Surveying Engineering at the University of New Brunswick initiated a research program, and the major points of investigation conducted to date are as follows: 1. Based on practical experience and theoretical studies, all factors influencing classical shaft-plumbing procedures were analyzed. Refined methods were developed to increase accuracy. 2. The performance of electronic and optical distance-measuring instruments in underground conditions were investigated. In this connection, test measurements were made in various mines, employing four types of Tellurometers, two models of Geodimeters and a proto-type optical range-finder. 3. Tests were conducted and methods developed for the mapping of large underground chambers by photo-grammetric means. The aforementioned points are discussed at some length in the paper. The authors have also indicated areas where further research is needed and suggested ways and means to improve and modernize mining surveying as a whole throughout Canada."

Jan 1, 1967

By Jay A. Carpenter

THIS preliminary report from the Committee to Study Relations Between Students and the Institute is submitted to our member- ship for consideration and discussion before the general subject comes up for action at the Annual Meeting in February. At present, the A. I. M. E. has a dual relationship with mining students, each relationship in no may connected with the other. To the individual student the Institute offers for $2 a year a Student Associateship in the Institute which carries with it a subscription to MINING AND METAL- 'LURGY, a watch fob, and the privilege of becoming a Junior Member after graduation without payment of the -first year's dues, if one's application is accepted. To the student's college society it offers the privilege, upon application, of becoming 'an Affiliated 'Society, which brings with it no specific supervision or aid, and in turn requires no specific conditions as to membership, fees, or rules. This Affiliated Society is distinctly a school organization which Student Associateship in the Institute can he given special status or ignored, is the local .society sees fit.

Jan 1, 1934

By R. A. Hill, J. D. Pitts

"Long distance slurry pipeline systems have been successfully trans-porting steam coal, iron concentrates, copper concentrates and limestone for an aggregate of nearly 60 years and nearly three billion ton-miles annually. A phosphate concentrate pipeline is nearing start-up and systems for coking coal, lead/zinc concentrates and fly ash are planned. The solids pipeline concept, first patented in the early 1900's and commercialized in the 1950's, is now a proven technology providing an economic, environmentally pleasing and safe method for long distance bulk transport.The challenge for larger tonnage and longer distance movements of solids, for traversing increasingly rugged terrain in grass roots mineral developments, for transporting untried materials and for shipping more economic forms of proven materials still remains. This has necessitated continued refinements and optimization of the technology. The economic and environmental incentives for slurry pipelines when compared to other transport alternatives has justified substantial activity in this area. The scope of planned systems in coal, iron and other minerals is indicative of the firm place slurry pipelines will have in worldwide mineral development.In this presentation, the state-of-the-art in long distance slurry pipelines is reviewed with a focus on major systems of interest to the mineral processing industry. An overview of new developments in the application of this concept is presented, and finally, a projection of the future of pipelines in mineral development both worldwide and in Canada is discussed."

Jan 1, 1978

By S. N. Monteiro, J. Alexandre, N. Cerqueira, B. C. Mendes, A. R. G. Azevedo, G. C. Xavier

Brazilian civil construction generates a huge amount of waste in different stages of construction, mainly due to the work methodology used in construction sites. The objective of this work is to study the inclusion of the residual of the civil construction in the sand mass in 0, 10 and 20%, with mortars used to cover masonry. For this study, the beneficiation of the material in crusher was obtained so that it obtained granulometry similar to sand and the most recurrent technological tests in mortars for this purpose, as the mechanical resistance (compression and flexion), water absorption and determination of the coefficient of Capillarity beyond the index of consistency, according to Brazilian norms, that define parameters of execution the technological tests. The results showed that the mortars after the incorporation presented value within the norm except the consistency and capillarity to the 20% that presented problems of fluidity and durability, hindering its use.

Mar 1, 2018

By van der Walt TJ, van Deventer JSJ, Reuter MA

Owing to their complexity, many metallurgical processes are difficult to model fundamentally, and as a result more attention has been focused on the use of artificial intelligence techniques to simulate these processes. In this paper recent advances in the use of neural nets to model processes not amenable to conventional methods are discussed. These include the application of a new modelling methodology based on the use of neural nets for the dynamic simulation of metallurgical processes, the use of conventional techniques in conjunction with neural nets to simulate gravity separation circuits, as well as the detection of gross errors in variable measurements by means of a neural net representation of the relation between measurement and constraint residuals.

Jan 1, 1993

By Kerry Spickelmier

The only nickel smelter and the only active nickel mine in the United States is Glenbrook Nickel Co., a joint venture (50% each) of Cominco Resources International Ltd. and Cominco Ltd. In 1989, with the nickel price riding high between $2.30 and $2.70/kg ($5 and $6/lb), Glenbrook seized the opportunity to purchase and recommission a southwestern Oregon ferronickel smelter and the adjacent nickel-ore mine. This Douglas County site is only about 97 km (60 miles) due east of the Pacific Ocean, and California's border lies a similar distance to the south. Hanna Mining Co. had closed the operation in 1987. And the following year, the equipment had been largely stripped for salvage value. From November 1990 through August 1992, the mine supplied an average 5 kt/d (5500 wet stpd) of ore. Currently, with import ore supplying 40% of the smelter feed, the mine's daily tonnage averages 4.2 kt (4600 wet st). From November 1990 through August 1993, the mine has delivered 2.1 Mt (2.3 million st) of ore grading 1.22% nickel with an average moisture content of 26%. Buffaloed nickel? A nickel is not worth what it was in 1989 and neither is ferronickel, with recent prices hovering around $1.13/kg ($2.50/lb). To survive, Glenbrook has focused on increasing smelter production to lower its operating costs. And this strategy has triggered several bold moves: • a new, $30 million, port facility and • a 10-year importation contract for ore from New Caledonia, an island approximately 1000 km (625 miles) east of Australia. For a Glenbrook update, a May 25, 1993 visit was made to the company's Oregon operations - the mine and smelter near Riddle plus its new Coos Bay port facility. Unfortunately, as the rain came down that day, so did news of another temporary shutdown. The previous suspension had lasted from Dec. 20, 1992 until Feb. 22, 1993. Barely three months back to work on a wet May afternoon, more than 250 of Glenbrook's approximately 300 employees contemplated yet another shutdown, effective July 31, 1993.

Jan 1, 1993

By Oliver Bowles

Accidental explosions in coal mines are due to various causes, but many of them can be directly attributed to coal dust; others that probably in no way depend on dust as a primary cause are propagated, greatly intensified, and made more disastrous by the presence of coal dust. The fact that coal dust in a bituminous mine will explode as a result of a fire-damp explosion has been generally accepted for many years, but the belief has also been held by many that coal dust is not in itself dangerous when unmixed with an explosive gas. Therefore, in past years little attention was given to dust in mines free from fire damp, and many disastrous explosions have resulted from lack of knowledge of the danger from coal dust. In the explosives gallery and experimental mine of the Bureau of Mines experiment station, Pittsburgh, Pa., it has been proved repeatedly and conclusively that coal dust will explode violently when no inflammable gas is present. PROPAGATION OF DUST EXPLOSIONS A coal-dust explosion is an extremely rapid burning or combustion of the coal particles. Their burning consists essentially of the combination of the hydrocarbons in the coal with the oxygen of the air, a process that generates heat and flame and produces hot gases and water vapor. These gases and vapors have a volume many times that of the original coal particles; thus they exert an outward motion and pressure which constitute the explosive wave. When fine particles of coal are suspended in the air, each particle is surrounded by the oxygen of the air, and thus is well placed to oxidize or burn rapidly whenever the temperature is high enough. If some particles are ignited from any cause they will fire others, and the combustion will extend from particle to particle with extreme rapidity wherever enough coal dust of sufficient purity is present.

Jan 1, 1925