Search Documents

By H. Wilton Clark

"IntroductionTHE CANADIAN use of short-period delay-action detonators in coal shooting has been carried on for about two years, mostly in British Columbia, and this is a preliminary report on progress to date. Entire coal faces are being shot successfully with one application of electric current.The electric blasting cap came into use about the beginning of the century. The low-tension electric cap, the type most commonly used, consists essentially of a metal tube containing an initiating explosive. Two wires lead into the end of the cap and are connected inside the cap with a short 'bridge wire .of very high resistance. This •bridge wire is buried in a match-head of a readily ignitable powder composition. When current goes through the lead wires, the bridge wire becomes extremely hot and sets• off the match-head which, in turn, ignites the powder just below it in the tube. This explosion sets off the main charge of explosive. Thus, by connecting a group of caps to a source of electric .current, a number of charges could be exploded simultaneously. This immediately became of great value to mine and quarry operators. Explosives could now be used to break up large masses of material at one time, as against the older, slow method .of blasting small amounts with single charges.The next step was to develop a delay detonator which would allow charges of explosive to fire one after the other, one or two seconds apart. Such detonators allowed first blasts to relieve some rock burden before the next charge fired, giving the second charge an easier task in forcing out more rock, and so on for the rest of the series of charges."

Jan 1, 1953

By William R. Yernberg

The combined 76th Annual Minnesota Section of SME meeting and 64th Annual University of Minnesota Mining Symposium were held April 8and 9, 2003, in Duluth, MN. This year’s theme was “Stakeholders, Partners in Change.” The meeting included four keynote speakers, technical presentations and a tradeshow. Engineers, executives, mining managers and suppliers from throughout the United States and eastern Canada attended the meeting. Reflecting the theme of the meeting, all agreed that the mine owners, the government, the community and the employees are all “stakeholders.” They must be “partners in change” for the iron ore mining industry to survive in the region. Compared with past meetings, where improved technology was the primary focus, this year the focus was on the dramatic restructuring of the entire industry. As noted by several of the speakers, “This time, the change is not in technology.”

Jan 1, 2003

The Porgera Joint Venture commenced production during September 1990. A small tonnage underground mine extracts high grade gold ore using small scale stopes. Conventional drill and blast methods are used for development and production mining. Ground support is effected with Splitset anchors, grouted rebar bolts and grouted cable bolts. Splitsets and grouted rebar can be installed by mechanised means. Vertical crater retreat, slot and massfire, and modified VCR stoping tech- niques are used at Porgera. Stopes are backfilled with a relatively strong cemented rockf ill. Future stope sequences require recovery of pillars beside and under filled stopes.

Jan 1, 1991

By David E. Nicholson

The Bureau of Mines has constructed a special compression chamber for developing stress-strain relationships of mine backfill and simulating the high compressive ground pressures encountered in underground mines. A one-dimensional, or Earth-Pressure-at-Rest model is proposed for backfills subjected to these pressures. Results of the compression tests performed in the chamber indicate that reliable stress-strain relationships can be developed from these tests. The primary objective of the test series was to evaluate the effectiveness of compaction of common backfills in retarding ground closure. Analysis of the stress-strain data shows an eightfold reduction in relative strain in optimum well-graded, compacted backfills over poorly graded, loose backfill material. Analysis of the one-dimensional compression test data also indicates a significant retardation of transmitted stress in dense compacted samples of backfill and natural sands. Although not fully understood, a deformation mechanism is thought to occur at the intergranular contacts in cyclic fashion causing frictional heat loss and a reduction in transmitted stresses in the densely packed materials. The experimental values of transmitted stress are compared with theoretical values of effective stress calculated from the one-dimensional compression relationships developed by Hendron (4).3 These experimental values of transmitted stress compare very closely with the theoretical values of effective stress.

Jan 1, 1968

By J. Rogans

This paper discusses the comparative performances of the three activated carbon adsorption circuits at the West Wits operations of Anglogold. These circuits consist of two pump-cell circuits (at Two Plant, formerly Elandsrand and at Three plant) and a conventional counter-current adsorption circuit (at Mponeng plant). The implications of the improved performance of the pump-cell plants are discussed.

Jan 1, 2002

By Mingming Zhang, Marshall S. Coe, Marcelo W. Andrade

To supply iron units and flux burden in blast furnaces, sinter basicity is one of the vital parameters for sinter plants. The sinter basicity also plays an important role in sinter quality since it imparts the formation of different mineral phases in sinter. Pot-grate sintering tests were carried out with low and high basicity to investigate the effects of sinter basicity on sinter mineralogy, properties and productivity. It was found that with an increase in sinter basicity, both sinter productivity and reducibility (RI) increased. Tumbler index (TI) and low temperature degradation index (LTD) of high basicity sinter were comparable to low basicity sinter. Softening and melting tests showed that sinter with 3.5 C/S basicity had slightly higher softening temperature comparing to lower basicity sinter with C/S 2.6, acid and fluxed pellets. XRD analyses confirmed the formation of silico-ferrite of calcium and alumina (SFCA) and calcium ferrite (CF) in the tested sinter samples.

Jan 1, 2015

Traditionally, capital costs of major resource development projects have been estimated as a single amount to which a percentage accuracy has been assigned based on the method of preparation of the estimate, that is, on the amount of information available to develop the estimate.However, there is a growing recognition of the importance of a probabilistic approach to capital cost estimates, and of a more rigorous calculation of estimate accuracies and of the presentation thereof. Accuracies can be expressed with more certainty as a percentage of the estimate amount where the percentage represents one standard distribution on the probability curve for the capital cost of that specific project. Thus confidence levels can be stated for various estimated amounts - for example, it can be stated that there is an 85% chance that a stated amount will not be exceeded, or a 90% certainty that a (higher) amount will not be exceeded. Moreover, the right skewness of the probability distribution curve for most projects can be readily recognised and reflected in the evaluations. This enables senior executives and board members to have a clearer understanding of investment uncertainties, and the possible magnitude of commitments.

Jan 1, 1990

By P. Leo

The Al-Zn-Mg alloys (e.g. 7004, 7020) are employed for land transport and architectural applications whereas the Al-Zn-Mg-Cu alloys (e.g. 7075, 7050) provide the high strength aircraft alloys. The Cu gives rise to suitably sized and distributed precipitation but causes high quench sensitivity. Their hot work processing also has marked differences; the Cu-free alloys have good extrudability whereas the Cu-bearing alloys have low extrudability and are difficult in rolling as well. The behaviors of the two classes are described in terms of flow stresses and ductility over 300 - 500°C, along with constitutive contrasts. The ductility of the alloys with Cu is much reduced above 400°C by precipitation of a phase at the grain boundaries that can be avoided by suitable heating schedules. The high strength alloys are subject to de-lamination corrosion of sheared edges due to severely pancaked grains; this can be alleviated by holding between passes, in mid-rolling schedule. In torsion tests at 10-1 to 10 s-1/ 250 - 500°C, the stresses (ductilities) at 300°C/ 1s-1 and activation energy Q for 7004 were 118 MPa (2) and 262 kJ/mol. The 7075 was tested after several pretreatments: completely over-aged (softened): 107 MPa (5), Q=150 kJ/mol; whereas, solution and quick cooling to testing caused extraordinarily high peaks related to dynamic precipitation resulting in 160 MPa (1.2), Q=300 kJ/mol.

Jan 1, 2011

By M. A. Oskouei

Draglines are the main energy consumers in strip mines. Given the growing cost of energy and environmental concerns, it is important to properly understand dragline energy efficiency. The goal of current research at Missouri University of Science & Technology is to account for operator practice and operating conditions in modeling dragline energy efficiency. This paper presents preliminary correlation analysis and a framework for stochastic modeling of dragline energy efficiency. Thirteen operating parameters (including cycle times, payload, swing angle, and height of dump pile), operator working schedules, operating conditions, and drag, hoist, and swing energies were monitored for an 85 yd3 dragline. Operator effects were examined by two-sample t-tests. The relation between the parameters and energy consumption were assessed by correlation analysis and a stochastic modeling framework has been proposed for dragline energy efficiency. The results show that operator effects are significant (p< 0.05) and energy efficiency is correlated with operating parameters. The completed model will help the coal mines better predict energy consumption, with uncertainty, for different operating conditions.

Feb 27, 2013

By M. Paczkowski

The use of inert gas systems to extinguish mine fires has been the subject of research for some time in the United States. In some European countries, it is an established practice. Tests were conducted with the CMI Inert Gas System (CMI), which is being used by the Polish mining industry. This system utilizes a modified jet aircraft engine and afterburner as a compact source of combustion products with a very low (less than one percent) oxygen content. Water injected into the combustion products stream provides evaporative cooling and forms a mist with a high cooling capacity. The CMI system was used under controlled conditions to extinguish coal pile fires at the U. S. Bureau of Mines Experimental Mine in Bruceton, Pennsylvania. The test results show that the CMI system can be used conveniently to extinguish fires quickly and to maintain an inert atmosphere in the fire zone to prevent re-ignition.

Jan 1, 1982

By L. G. Stolarczyk, Y. Luo, S. S. Peng

Detection and assessment of severe geological anomalies ahead of a longwall face greatly benefits the mining operation. Electromagnetic-based Radio Imaging Method (RIM) is one of the most promising geophysical methods for this task. Based on two decades of development, the latest RIM instrumentation (RIM-IV) has expanded its operational range up to 1,800ft.A site demonstration of the RIM-IV technology was recently conducted within a longwall panel. An extensive ground truth study was performed to evaluate the accuracy of the RIM survey results. This study compared the generated RIM tomograms of attenuation rate with the mapped geological anomalies. Three different approaches have been employed to examine the accuracy of the RIM results and to correlate the measured signal attenuation rates with physical properties of the coal seam. The study shows that the RIM-IV technology is able to identify and delineate those geological features that would severely affect the longwall mining operation.

Jan 1, 2004

By F. W. Glaser, Benjamin Post

A LTHOUGH most transition metals form a wide variety of boride compounds, the existence of only one zirconium boride, ZrB2, had been established prior to this investigation.&apos; The crystal structure and some properties of a hitherto unreported zirconium boride, ZrB12, are described in this paper. Only one other dodecaboride of a transition metal, UB12, has been reported up to the present.&apos; Chemical analysis of the new compound showed 44 pct Zr and 56 pct B, compared with 41 pct Zr and 59 pct B computed for ZrB12. The difference is within the range of error of the analytical method employed. ZrB12 shows marked metallic properties. It is obtained as a fine black powder. Measurements of electrical resistivity were made at —79°C, + 22°C and +64°C. At 22°C the electrical resistivity is approximately 60 microhm-cm. Over this range the temperature coefficient of resistivity is +0.00162. The thermal conductivity at room temperature is 0.122 watts per cm per "C. The product of the electrical resistivity and thermal conductivity is therefore 8.05, which is not far from the normal Wiedemann-Franz ratio (approximately 7.5 at room temperature). These measurements were made on hot pressed samples which were not always high density specimens. The hardness of ZrB12 on the Rockwell A scale varies between 92 and 92.5. Crystal Structure Determination Single crystals of ZrB12 of a size suitable for X-ray diffraction analysis could not be obtained and powder samples had to be used. Filtered Cu radiation was used throughout. Powder diagrams were indexed on the basis of a face-centered cubic unit cell. After correction for film shrinkage, a Bradley and Jay extrapolation³ to ? = 90" indicated that a, = 7.408 ±0.002A. The volume of the unit cell is 406.5A.V he assumption that there are four "molecules" of ZrB12 per unit cell leads to an X-ray density of 3.63 g per cc. The measured density is 3.7 g per cc (as measured by the immersion method). Relative intensities of reflections were determined by integrating the intensities of diffraction peaks using the count register of a North American Philips wide range spectrometer. Intensities measured in this way showed good agreement with photographic intensities estimated visually using multiple film techniques. The usual Lorentz, polarization, and multiplicity corrections were applied to the observed intensity measurements. There are striking similarities between ZrB12, and UB12. The unit cell of the latter is also face-centered cubic and contains four molecules. a, = 7.473, compared with 7.408 for ZrB12. The radius ratio rB/rU is 0.57; rB/rZr is 0.54. In both ZrB12, and UB12 the four metal atoms in each unit cell are in special positions; only the boron positions need be determined. The latter may be inferred from the extent to which diffraction of X-rays by the 48 boron atoms reinforces or weakens the diffraction by the metal atoms. This effect is relatively much greater in the case of the zirconium compound. In their determination of the crystal structure of UB12, Berthaut and Blum&apos; assumed holohedral symmetry (space group Oh5 , Fm3m) and reported that the U atoms are in positions 4(a): 000; 01/2 1/2; ½ 0 ½ ; ½ ½; the boron atoms were reported to be in positions 48(i) with x = 1/6: ½xx; ½xx; x½x; x½x; xx½; xx½; ½xx; ½xx; x½x; x½x; xx½; xx½

Jan 1, 1953

By Walter Valery, Kristy Duffy, Alex Jankovic, Peter Holtham

Hatch’s Mine to Process Optimization projects integrate mining and processing strategies, minimizing operating costs and maximizing overall profit. The methodology involves ore characterization, blast audits, plant surveys, analysis of historical data, and integrated modelling and simulation of mining and processing. Blast designs are tailored according to ore type and the downstream process is optimized for the changed feed. This approach has increased throughput and minimized costs for many operations worldwide. The implementation of this methodology at an iron ore operation that faced challenges with increasing mining strip ratio and ore body mineralogy changes is presented in this paper. The larger stripping ratio increased mining costs and constrained the run-of-mine (ROM) delivery to the process plant. Process performance was affected as the ore mineralogy shifted from predominantly hematite to include greater proportions of magnetite. The project objective was to minimize overall cost per ton mined and processed and maximize profit. Tailoring the blast designs according to ore type and process optimization increased the throughput of all process lines. This provided the potential to shut down one of the five processing line, aligning the mine and plant capacity and significantly reducing the processing costs.

Oct 3, 2019

By Arthur Knapp

Oil-well depletion curves, to be of value, should show when a well or lease may no longer be operated at a profit. The difference, at any time, between the total expenditures and the total income of a lease or well may be called the lease status. Plotting this lease status against time will give a curve subject to more accurate and different interpretations than the barrels-time curves. According to the hypothetical barrels-time curves shown in Fig. 1, well A, at the end of 16 mo., is producing twice as much oil as well B and will continue to produce for another year whereas well B will cease producing in about 6 months. Data fob Lease Status-time or Dollars-timb Curve Time Lease Months Status Lease purchased for $3000.............................. 0 — $ 3,000 No expenses chargeable to lease for 3 mo................. 2 — 3,000 Well A is started; cost of drilling for month is $16,000..... 3 — 19,000 Well is completed at additional cost of $10,000............ 4 - 29,000 Well A is brought in and flows 10,000 bbl. first month (we Fig. 1). Necessary to invest in tanks, boilers, pipe lines, etc.; difference between expenditures and receipts gives profit for month of $5,000............................ 5 — 24,000 Investment is small, cost of operating well A is small, so profits are $15,000................................... 6 — 9,000 Well ceases to flow so there is additional investment for pumping equipment and additional operating expense; net earnings from 6,000 bbl. of oil produced is $4,000. 7 ... Lease operation nor becomes normal and curve becomes smooth........................................... 8 — 500 9 2,000 10 4,500 11 6,000 12 7,700 13 8,700 14 9,000 15 9,500 16 10,000 A hypothetical lease status-time, or dollars-time, curve of this lease is shown in Fig. 2. At zero time, the lease is purchased for $3000, which is plotted below the zero dollar line, All subsequent entries are plotted

Jan 1, 1921

By S A. Myers, T Klein

The Yanacocha mining district is located in the northern Andes of Peru. The project is within the Cajamarca province, 20 km north of the town of Cajamarca and 600 km north of Lima, the capital of Peru (Figure 1). The district encompasses an area of 120 km 2 and is centred on the 78030&apos;west longitude and 7000&apos; south latitude. The project lies at an elevation of 3400 to 4200 masl.

Jan 1, 1999

The theme of the conference is "excellence", an epithet of special significance in tertiary education. It appears in the mission statements, goals and plans to achieve them of most, and quite possibly all, tertiary institutions in Australia. In the context of excellence, this paper examines the current statue of professional education in the principal mining industry related discipline of Mining Engineering. It furthermore, identifies and discusses a number of special problems in mining education that the tertiary sector has long endured. Some of these problems are becoming acute, and solutions will have to be found soon in order for the industry to be assured of the supply of well motivated and appropriately qualified young engineers and scientists necessary to achieve and maintain the excellent to which it aspires.

Jan 1, 1989

Very little has been written about the discovery and early history of prospecting of ironstone deposits in the Iron Knob-Middleback Range area of South Australia, the main source of supply of ironstone (hematite) for the Australian steel industry, and scanty though the record is, much of it is wrong or misleading.With the help of several people, to whom acknowledgement is made at the end of the paper, the writer has unravelled some of the story, but not the whole story. It is hoped that publication of this paper will stimulate interest in others, who may be able to supplement this account from family records, from the files of newspapers, or from archives.

Jan 1, 1969

By Krogerus. H., P. Jokinen, T. Lintumaa

Keywords: Pyrometallurgy, furnace, coke, smelting charge, optimization, ferrochrome The main consumer of ferrochrome is stainless steel production. Stainless steel must maintain a reasonable price against other competitive materials. Therefore, the ferrochrome price must be low enough and profitable for the producers of stainless steel. The investment and operational costs of ferrochrome production are greatly dependent on the availability of the process and the production rate. Thus the furnace size and production rate in submerged electric arc furnaces will be greatly increased in the near future. The ferrochrome production per furnace, e.g. at Outokumpu?s Tornio Works, increased from 30 000 t/a to 165 000 t/a in about 35 years. The same trend will continue globally but now much more quickly. The Outokumpu ferrochrome process at Tornio Works uses sintered chromite pellets and upgraded lumpy ore as a chromite source. Metallurgical coke is used as a reductant. Reliable smelting in a large furnace demands the correct charge composition and well-known characteristics of the charge components. The quality and electrical conductivity of cokes (normally used) has the most important role for the electrical conductivity of the smelting charge. The results of the measured electrical conductivity of different cokes and the smelting charge with many controlling factors are presented here. These measurements were performed over the years for our own purposes at the laboratory of Outokumpu Research Oy (ORC), in Pori, Finland.

Jan 1, 2006

By J J. McEwan

Silver tarnishes readily in common atmospheres and is accelerated in humid atmospheres. Tarnish is the formation of silver sulphide on the surface of silver when it is exposed to a wide range of sulphur-containing atmospheres. Tarnish is unattractive and highly undesirable, and can be removed either with a silver polish or a chemical dip. Dips are generally only recommended when heavy black tarnish cannot be removed with a polish, and care must be taken during cleaning because these can contain aggressive chemicals and give off hazardous and unpleasant smelling fumes. Polishes work best for large areas of plain undecorated silver, and form part of a regular cleaning programme. Some polishes contain chemicals that inhibit tarnishing, but these generally only have a short life. Several methods have been developed to reduce tarnish formation on Silver; these include alloying, surface treatment, and coatings. The authors evaluated a range of self-assembled monolayer (SAM) surface treatments and coatings in earlier research. Four treatments/coatings increased the time to noticeable tarnish by more than ten fold, and the results were reported at the International Corrosion Congress (ICC) in 2005, and at the Mint Directors Conference (MDC) in 2006. SAM treatment using 95% 1-hexadecanethiol (C16H34S) was found to give good anti-tarnish performance and showed potential for the commercial treatment of Sterling silver. Therefore research was performed to optimise the methods of application of this type of coating to provide an easier, faster, and more-user friendly technique to provide an anti-tarnish treatment. Keywords: silver, tarnish resistant coatings.

Jan 1, 2006

By Luis Valdivia

Dado que el objetivo principal de un departamento de Geología de exploraciones es el de estimar recursos minerales en nuevos blancos de exploración identificados a través del análisis e interpretación de información geológica proveniente de diversas fuentes. En ese sentido, el presente texto señala la sistematización de los datos geológicos como el uso de las imágenes satelitales, fotografías aéreas, geofísica, geoquímica, cartografiado geológico, sondajes diamantinos, catastro minero, datos geográficos y políticos, etc. a través de un servidor que integre dichas estructuras lógicas de conocimiento, de manera que todos puedan acceder a ella de manera fácil y dinámica. Asimismo, para los datos de carácter numérico llámense muestras, sondajes, leyes, se utiliza la plataforma Access como gestor de base de datos, mientras que para la información grafica superficial, el software ArcGis.

Sep 24, 2008