Search Documents

By Philip B. Bucky

WITH the exhaustion of the sections of iron ore bodies amenable to opencut mining the iron ore miners raise the question: "How can we mine the extensions of these ore bodies in depth with the same costs as obtained in opencut work?" This question brings to the fore the relationship between mineral exploration and research on mining procedures. The iron miners must either find new de? posits amenable to their known methods of mining or develop new mining methods for deep deposits. It is understood that the oil companies will spend $30,000,000 next year in the search for new oil fields. How much the metal mining companies will spend in the search for new ore bodies is unknown, but without doubt the amount will run into several millions of dollars. If the mining companies that concern themselves with metals, nonmetallics, and fuels will set aside a substantial sum for fundamental and applied research in mining methods, they can not only lower their costs but increase their reserves thereby. Any increases in mining efficiency automatically result in increased ore reserves at no cost.

Jan 1, 1947

While SME is hosting its Annual Meeting at the Phoenix Convention Center, Feb. 28 to March 3, one of the finest collections of mining history will be on display just 15 blocks away at the Arizona Mining and Mineral Museum. Inside the museum, visitors will be treated to a treasure trove of minerals, gems, me¬teorites, rocks, fossils, mining artifacts, historical exhibits and interactive displays on modern mining. The museum is located at 1502 West Washington. For SME Annual Meeting attendees, this is a free, eight-minute Dash bus ride 15 blocks west of the Phoenix Convention Center.

Jan 1, 2010

By Foluke Salgado de Assis

Este trabalho visa apresentar os resultados obtidos através de ensaios balísticos realizados em sistemas de blindagem multicamada. Seguindo as especificações da norma americana NIJ 0101.06, foram realizados ensaios utilizando munição de calibre 7,62x 51 mm, que possui velocidade acima de 800 m/s. A blindagem multicamada utilizada possui como camada frontal uma pastilha hexagonal cerâmica (alumina dopada com 4% de nióbia), segunda camada de compósito de matriz poliéster reforçada com tecido de juta e como terceira camada uma placa de alumino 5052 H34. A utilização de compósitos poliméricos reforçados com fibras naturais em substituição às fibras de aramida é de grande interesse, pois além de desempenharem a mesma função no sistema de blindagem, possuem um valor de mercado bem menor. Os resultados de profundidade de indentação na plastilina foram satisfatórios visto que atenderam a norma NIJ 0101.06 e utilizando a técnica de microscopia eletrônica de varredura, verificou-se que o compósito poliéster-juta capturou os fragmentos através do mecanismo de incrustação mecânica.

Aug 17, 2017

By D. E. Hartman, J. M. Roberts

A detailed study of the temperature dependence of the critical stress, TB . necessary to cause a damping loss of 1.41 x 10-6 g mm per mm3 in pre-strained magnesium single crystals has been carried out in the temperature range 82" to 320°K. Tb is found to be linearly related to the reciprocal of the ahsol~cte temperature in this temperature range. The temperature dependence of the anelastic limit, TA, defined as the stress necessary to form open unidirectional stress-cycle damping loops has been measured between 82" to 320°K. ta is found to be independent of temperature in this range. It is suggested that TA is determined by the stress necessary to activate Frank-Read dislocation NUMEROUS studies1-9 have been reported concerning the details of yielding and microstrain near and below the generally discussed macroscopic flow stress. The work of Kramer and coworkers10-13 is helpful in determining certain qualitative facts. concerning preyield phenomena. The absence of a stress-dependent delay time in annealed copper and aluminum single crystals between 83" and 298 suggests that the preyield mechanism is temperature-independent in this range. This is not sources. The temperature and stress dependence of the effective activation volume (Veff) has been measured in the damping-loop region in prestrained magnesium single crystals. The data suggests that Veff/kT is approximately constant, equal to 2 4.5 sq mm per g in the temperature range 130°to 298°K, and that Veff is almost independent of stress at stress levels greater than 10 g per sq mm. A restricted model is developed to predict the stress (rb) necessary to cause a small fixed damping loss as a function of temperature, effective activation volume, and dislocation density. Various possible dislocation mechanisms controlling TB are discussed. true for zinc, p brass, and iron crystals in the same temperature range, however, since the existence of a stress-dependent delay time suggests a thermally activated preyield mechanism in these materials.10-13 The work by Vreeland et a1.14 confirms the work by Liu et al.ll on delayed yielding in zinc single crystals. A stress-dependent delay time between 82" and 298°K was found12 in prestrained aluminum and copper crystals. These results suggest that the preyield phenomena may be different between prestrained and unstrained or annealed crystals. The temperature dependence of the yield point at 2 x 10-8 plastic strain found by Rosenfield and Averbach3 in annealed copper and aluminum is not in agreement with the delay-time data, unless possibly the delayed yielding experiment only de-

Jan 1, 1964

By Greaves M. C

X-ray fluorescence spectroscopy used for the analysis of mill samples results in improved control of flotation concentrators.Techniques and equipment for sampling pulp streams, filtration and drying, grinding, briquetting and X-ray fluorescence analysis of samples have been developed.The current methods in use permit the analysis for lead and zinc in six pulp samples within 30 min total elapsed from the start of sampling. The X-ray method gives a precision at least equal to the former routine wet-way assay methods.The equipment is used also for pilot plant control, as a means of solving complicated analytical problems and in the rapid qualitative analysis of exploration samples.INTRODUCTIONIn milling and concentrating operations, classical methods for the assay of lead and zinc have been mainly of use for accounting purposes and for the post-mortem examination of plant operations, but have been of little value for rapid mill control. Where attempts have been made to apply these methods to control assaying, it has been necessary to modify the procedures and introduce short cuts which have tended to reduce their reliability.Even with these shortened procedures, the time taken to obtain a limited amount of information rendered them of little value for the control of milling operations where sudden, large fluctuations can occur. In recent years, a number of new and rapid analytical techniques, based on physical rather than chemical principles, have been introduced.These include direct reading emission spectroscopy, x-ray fluorescence spectroscopy and atomic absorptionspectroscopy.

Jan 1, 1964

By Mark G. Lafontaine

Underground 802.11 wireless communications has become widely adopted for automation and communication purposes but maximizing the wireless signal presents many obstacles given the harsh environment as well as the presence of materials and conditions that can reduce signal propagation. Changes in elevations and curvatures in ramp to drift transitions also affect the wireless signal. Based on the requirements of wireless applications such as voice, data, or location tracking, the wireless site survey is the key tool for measuring and predicting signal strength and signal-to-noise ratio. These readings help determine the maximum distance between access points in order to sustain an overlapping wireless signal where required. This paper describes the methodology and tools used for measuring 802.11 wireless signal strength in an underground mine environment in Northern Ontario. The physical characteristics of the mine and the actual recorded wireless signal data will be presented in order for the audience to gain an understanding of the factors that affect signal throughput. Antenna selection used for the site survey will also be discussed as it played a key role in propagating the wireless signal.

May 1, 2013

By Jorge Meza

Uno de los objetivos principales del proyecto de la modernización de la Fundición SPCC es capturar y procesar el gas generado de la reacción exotérmica del proceso de fusión de los sulfuros del concentrado para transformarlo en un subproducto comercial que es el (ácido sulfúrico) H2SO4. En ese sentido, el presente texto señala el manejo de un sistema de control de gases a través de un proceso sofisticado para el enfriamiento, limpieza y manejo de este gas de dióxido de azufre, reduciendo los costos de operación, así como el tiempo de reacción de los equipos involucrados en el manejo y procesamiento de los gases.

Sep 19, 2006

By R. K. Ham, M. L. Wayman

TD-Nickel has been broken in tension and in fatigue at voom temperature. Rod specimens failed in tension by necking, with axial cracks attributed to voids elongated in the extrusion direction. Fatigue specimens failed in shear. Thin-film electron microscopy showed that the subgrain structure of TD-Nickel was very stable, and that particle-matrix detachment was very difficult, in tension and fatigue. TD-Nickel softened slightly during fatigue but had a high fatigue ratio (0.5at 10' cycles). Fractography suggested that Stage I fatigue crack propagation is greatly extended in TD-Nickel. Td-NICKEL* is a dispersion of 2 pct by volume of thoria (ThO2) in nickel, produced by powder-metallurgical methods including compaction, sintering, and extrusion. The spherical thoria particles, which may have a mean diameter of a few hundred angstroms, are dispersed with a mean planar spacing of a few thousand angstroms. By a combination of cold working and annealing, a subgrain or cell structure of dislocations intimately associated with the dispersion can be produced.' This gives the material useful tensile properties which are extremely resistant to exposure to high temperatures.'-= At the same time, the material shows considerable ductility.3'4 At the beginning of the present work, it was considered of great interest to investigate the mechanical stability of TD-Nickel under conditions of fatigue. On the one hand, materials which derive strength from a cold-worked structure are unstable in that they are susceptible to fatigue softening: in addition, the presence of discontinuities such as the particle-matrix interfaces might be expected to assist in the initiation and propagation of fatigue cracks, in that they may provide local concentrations of internal stress and sites for the initiation of voids." On the other hand, the substantial ductility of TD-Nickel suggests that if it obeys Coffin's relation8 (or the more refined form proposed by Manson9) it should have good fatigue resistance. The initial purpose of this investigation was to assess the importance of these factors. Also, relatively little fundamental work has been done on the mechanism of fatigue in dispersion-strengthened materials. Work on overaged A1-4 pct CU10-12 revealed a very large Bauschinger effect indicative of internal stresses at the particles, and very great fatigue hardening1' presumably due to the multiple slip stimulated by these internal stresses, followed by softening which was initially due to softening in the matrix, but later might have arisen from cracking at the particle-matrix interfaces. The study of overaged Al-4 pct Cu could not settle this latter point by the electron microscopy of thin films, since the dispersion is too coarse. A previous study of the fatigue of internally oxidized copper13 was complicated by inter granular failure, attributed to oxide particles at grain bouhdaries; internal oxidation of single crystals, however, improved their fatigue properties.'3 Investigations of SAP (sintered aluminum powder) are complicated by the complex particle shapes, and the possibility of continuous internal oxide films.14 It was hoped to avoid these difficulties with TD-Nickel, which had the further advantages that it was commercially available and suitable for study by the thin-film technique. 1) MATERIALS AND EXPERIMENTAL PROCEDURE TD-Nickel was purchased from the Driver-Harris Co. as 3/9-in.-diam rod which had been extruded, swaged, and "stress-relieved" (normally at 1010°C for 1 hr). Continuous-radius fatigue specimens with a minimum diameter of -0.1 in. were ground to shape and electropolished in 40 pct phosphoric, 35 pct sul-furic, 25 pct water at 25oC, with a stainless-steel cathode, at -6 v. Fatigue tests were carried out at room temperature with a Sonntag SF-1-U machine operating in push-pull at 1800 cycles per min, and in an Instron TT-C-L modified for reversed stressing at 26 cycles per min as described elsewhere.10 Round tensile specimens were ground with 0.85-in. gage lengths of 0.135 in, diam, electropolished, and tested in a Tinius Olsen hydraulic machine. The surfaces of fatigue specimens were examined with a Reichert metallograph. Discs for electron microscopy with a Siemens Elmiskop I were spark-cut 0.01 in. thick with a modified Servomet 11 employing a tool of moving molybdenum wire, cleaned in 50 pct acetic, 30 pct nitric, 10 pct phosphoric, and 10pctsul-furic at 85oC, and thinned by the window method in the electropolishing solution at -20°C and -6 v. Two-stage replicas (parlodion, then Pt-50 pct C self-shadowed at 40 deg) were taken from fatigue fracture surfaces for electron microscopy. Plane sections parallel to the specimen axis and containing the direction of fatigue crack propagation were polished, etched with Carapella's reagent, and examined optically. Transmission Laue X-ray photographs of as-received material electropolished to a point were used to determine preferred orientation. 2) RESULTS 2.1) The Structure of As-Received Material. Grains -1 µ diam and elongated 20 to 30 u in the direction of the rod axis were observed, With' elongated "intergran-ular" voids (-4 p diam and -90 µ long and identified as such using longitudinal and transverse sections and

Jan 1, 1968

By N. S. Stoloff, R. G. Davis

It is concluded from an X-ray stztdy that the formation of the hcp Mg3Cd superlattice is a nuclea-tion and growth reaction. A two-phase, ordered-plus-disordered, region is observed between 153" nnd 141"C. A maximum in the flow stress is observed both at temperature and in quenched specimens within the two-phase region. The peak arises fro112 the extra energy required to create antiphase boundary upon cutting the ordered regions. Hardening during isothermal annealing in Mg3Cd has been shown to be similar to the domain hardening in Cu3Au-type alloys in that up to the maximum the structure is ordered domains growing into a short range ordered matrix. The hardening is due to a combination of short range order strengthening and the strengthening produced when antiphase boundary has to be created. In a recent study1 of the effect of long-range order upon the mechanical properties and deformation modes of hcp Mg3Cd a comparison was made be- tween quenched (disordered) and slow-cooled (fully ordered) specimens. The most striking observations were that the disordered alloy yields at a much higher stress than the ordered alloy, and that there is a change in slip mode from primarily (_0001) ba_sal slip in the disordered state to (0001), {1010}, {1122}, and {l011} slip in the ordered state. The main purpose of the present work is to extend these observations to determine whether MgsCd exhibits a peak in flow stress at an intermediate degree of order, or at a critical domain size, as do other orderedstems. However, disagreement exists about the Mg3Cd order transformation with respect to: 1) the location of the critical temperature for order, 165°C or 153"~,' and 2) how the degree of order varies with temperature. Welber et a1.5 concluded from specific heat measurements that the formation of Mg3Cd is a second-order reaction with the degree of order a continuous function of temperature, while Moore and Raynor concluded that it is neither a first-order reaction, with the degree of order a discontinuous function of temperature, nor a second-order reaction. Consequently it was considered necessary to undertake an X-ray investigation into the change in degree of order and structure in the

Jan 1, 1964

By C. E. Birchenall, R. H. Condit

THREE surface activity procedures are in com--L mon use for the determination of diffusion coefficients in solids. In the oldest of these' the activity observed at the original surface is compared before and after diffusion, where all the activity is in a thin, plated layer on the surface before diffusion. Partial absorption of the radiations from active atoms which have diffused below the surface reduces the effective activity after diffusion. The formula employed to calculate the diffusion coefficient is where F, is the ratio of final to initial activity at the surface, measured with identical counting geometry; Z=u3Dt, where D is the diffusion coefficient; t is the diffusion time; and u is the absorption coefficient for the radiation in the solid as defined by Lambert's law. This absorption law implies that all the rays are parallel to each other and normal to the specimen surface. This assumption of a collimated beam used by Steigman, Shockley, and Nix has been adopted by all other investigators and, although it gives results which are approximately correct under restricted physical conditions, it does not represent many actual circumstances. It is the purpose of this paper to show the importance of the divergent rays and to indicate a procedure for taking them into account. In the residual activity method the activity is determined on a series of surfaces ground on the specimen at progressively greater depths in the diffusion layer parallel to the initial surface. Gruzin2 has de- rived a formula for this procedure, which may be put in the form where I is the ratio of the activity measured at a newly ground surface at distance k below the initial surface to the activity at the initial surface measured after diffusion, and K= k/2p Dt. A third procedure involves the autoradio-graphic determination of activity on a plane ground at a small angle to the initial interface through the penetration zone. Aut oradiography can be particularly sensitive to the oblique rays. Unlike most counters which detect essentially all ß particles or X-rays which enter the active volume as a single event, the photographic emulsion may be thin enough so that oblique rays with longer path length in the emulsion produce more darkening than rays which move normal to the film plane. Consider a plane containing a source of radiation uniformly spread over a circle and a point counter located on the perpendicular through the center of the circle. As the counter moves along this line, the total angle 6, at the counter subtended by the specimen will vary. For a fixed counter distance, let 6 be angle between the counter axis and the line connecting the counter to a point P on the active plane. If an absorber of thickness X is interposed parallel to the source between counter and source, the ray from point P to the counter will pass through an absorber thickness X secant 6. Exponential absorption is assumed to hold for all rays. If r, is the ratio of intensity at the counter with absorber to the intensity without absorber and a = pX, 1 00 The behavior of this integral, evaluated numerically,

Jan 1, 1957

By P. R. Jones

A computer program was written for the design of a shell and tube heat exchanger on a price optimum basis for the following conditions: (1) Triangular pitch; (2) single or multiple pass; (3) heating or cooling; (4) no change in phase; and (5) inside pumping costs immaterial. Price optimum design was obtained for four standard tube sizes and standard pitch. The inside pressure drop was fixed and outside pressure drop was computed for the optimum baffle spacing and when the baffle spacing equaled the shell diameter. Standard shells whose areas equaled or exceeded the required area were also listed. The program was made adaptable to various fluids and to various tube sizes and pitch by reading in many of the required data such as physical properties of the fluids, tube data, and standard shell data in tabular form.

Jan 1, 1968

By Maria I. De Rosa

The major fire and fire injury findings for all metal/nonmetal mining categories for 1990-2001 are shown in tables 64-65. Table 66, partly illustrated in figure 22, shows the number of fires, fire injuries, fire fatalities, risk rates, employees' working hours, and lost workdays for all metal/nonmetal mining categories by time period. For all metal/nonmetal operations (including stone and sand and gravel), a total of 518 fires occurred during 1990-2001; 296 of those fires caused 308 injuries and 4 fatalities (Ewhr = 4,012 x 106 hr, In = 0.015, LWD = 36,204). Thirty fires and 26 injuries involved contractors. The greatest number of fires and fire injuries occurred at surface operations; the highest risk rate values were also calculated for surface operations. The number of fires increased during the first four 2-year time periods (1990-1991, 1992-1993, 1994-1995, and 1996-1997), then decreased during the last two periods (1998-1999 and 2000-2001). The number of injuries showed a decrease throughout the periods, accompanied by an increase in employees' working hours. Twenty-five firefighting interventions by mine rescue teams in underground mines and at least 30 interventions at surface operations were required to combat these fires. However, 45 fires destroyed or heavily damaged facilities and equipment (including 19 pieces of mobile equipment) because of failure of firefighting methods, late fire detection, undetected fires, or fire size. Ninety-seven fires were detected late, and 30 fires were undetected. The ignition sources that caused the greatest number of fires were flame cutting/welding spark/slag/flame (169 fires or 33% with 137 injuries), hydraulic fluid/fuel sprayed onto equipment hot surfaces (89 fires or 17% with 46 injuries and 3 fatalities), heat source/explosion and flammable liquids/ gas/refueling fuel on hot surfaces (98 fires or 19% with 73 injuries), electrical short/arcing (51 fires or 10% with 16 injuries), and spontaneous combustion/hot material (46 fires or 9% with 17 injuries). The flame cutting/welding spark/slag/flame source caused fires usually involving welders' clothing or oxyfuel/grease and other materials (including chute and dust collector liners, flammable liquids, belt material, crusher, hopper and shaker deck materials, washer plants, equipment mechanical components, stampler breaker, hydraulic fluid, rubber tires and hoses, gear boxes, bin feeder, dump rope cables, screen liner and screen panel, kiln and shaft material, pipelines, liquor pumps, wood pallets, electrical junction boxes, handrails, grease, refuse, shop and wood). The spontaneous combustion/hot material and electrical fires were usually detected late due to lack of combustion gas/smoke detection systems. At least 55 of the 89 mobile equipment hydraulic fluid/fuel fires became large fires (requiring 12 mine rescue team interventions in underground

Jan 1, 2004

By Tim Peterson

Factors Controlling Stability Stability of slopes in soft rock, waste dumps or soils is governed by three factors: ?Slope configuration ?Groundwater ?Shear strength

Jan 1, 2004

By D. Eastick, S. Hardcastle

"Over the last few years, a multi-faceted feasibility study has been evaluating the introduction of hydrogen fuel cell-powered equipment into underground mines to replaced diesel engine-powered equipment. The analysis has shown that under normal operating conditions fuel cells could at the very least be an environmental and health benefit by eliminating combustion engines and their unwanted by-products. However, they could also generate significant reductions in the amount of ventilation a mine needs to supply when compared to dieselized operations; this would further decrease a mine’s energy consumption, its associated greenhouse gas impact, and also reduce a mine’s significant ventilation-associated costs. Fuel cell-powered equipment also has the advantage of lower noise and heat production compared to its equivalent diesel-powered counterpart.The degree to which fuel cells can generate ventilation benefits in underground mines depends upon a number of operational parameters and mine specific qualifiers such as current ventilation control or management, mine depth, inherent dust conditions, and minimum velocity requirements.However, another major consideration in the introduction of fuel cells in underground mines will be the safety requirements associated with diluting and removing the potentially explosive hydrogen in the event of a gas leak. In outside surface applications, it is possible to use dispersion, buoyancy, time, and lack of ignition sources as mitigating factors in deriving a low risk of an explosion. However, in underground operations, these factors change, and dispersion and buoyancy are limited; time may not be available and, in non-coal mines, ignition sources are not typically controlled. When a hydrogen leak occurs, the availability of sufficient ventilation to dilute and effectively remove the gas will be critical. Consequently, ventilation may be the prime risk controlling factor. In this paper, the authors evaluate the potential benefits of replacing diesel engines with fuel cells in powered production equipment, discuss the mitigating qualifiers that could limit ventilation savings, and evaluate solutions to retain and maintain an additional ventilation capacity in the event of an emergency situation, such as a hydrogen leak from the fuel cell stack or its distribution system."

Jan 1, 2007

By John Jonkman

The cost of equipment maintenance is the largest single expense at many mines and processing plants. It is not unusual for a maintenance and repair budget to be larger than 50% of the punt's total budget. Generally, in the mining industry, 400-60% of the work force in a plant reports to the maintenance department. Studies have shown that many plant maintenance workers are only 33 to 40% productive, working 2.6 to 3.7 hours of every 8-hour day. In recent years, many companies have begun to recognize that- productivity improvements and cost reductions can he achieved by upgrading maintenance methods. This paper discusses ten common causes of low maintenance productivity and how recent advancements in computing technology can be utilized to address these causes for low productivity.

Jan 1, 1986

By Y. Q. Zhang, S. S. Peng

Numerical modeling was used to design the pillars and bolting plan for a mine with weak roof and multi-seam stress condition. Previous mining experience, pillar/roof yielding and in-situ horizontal stress were considered in the models. By modeling the upper seam yielding and vertical stress transfer, a multi-seam influence zone was obtained. Appropriate pillar sizes were designed for conditions with and without upper seam stress influences. Roof support for the track and belt entries, using fully-grouted resin bolts and cable bolts, was proposed and implemented in the model. The bolting plan was evaluated under the weak roof condition.

Jan 1, 2004

By R. K. Singhal

Canada is a world class producer and exporter of minerals and mineral products. Today's highly mechanized Canadian open pits use state-of-the-art equipment and support technology. They are taking advantage of larger equipment, including in pit crushing and conveying, truck dispatch systems and electronic management tools. Mine planning is computerized. Environmental issues are dealt with in all phases of planning, and equipment modifications are pursued to keep them functioning in the hostile Canadian north. In 1991, Canada's mineral production (excluding fuels but including coal) totaled $C 16.9 billion, a decline of 13.8% from the 1990 total of $C19.6 billion. It is a major producer of nickel, zinc, asbestos, potash, molybdenum and uranium. Canada is also an important source of copper and iron ore (Fig. 1).

Jan 1, 1995

By Carlos Alberto Perim

Durante o lingotamento contínuo de placas de aço, muitas vezes ocorre uma queda acentuada de temperatura ao longo do processo. Fatores como o tempo de lingotamento, o superaquecimento inicial da panela de aço, a presença de cascão na panela, entre outros, podem alterar significativamente a taxa de queda de temperatura, levando muitas vezes à interrupção prematura do lingotamento. Neste trabalho, será mostrado o desenvolvimento de um modelo de predição de temperatura ao final do lingotamento de uma panela de aço. Este modelo permite antecipar, com razoável nível de incerteza, a temperatura final do aço no distribuidor durante trocas de panela, de forma que forneça subsídios para a tomada de decisão sobre a interrupção do lingotamento, ou a antecipação de abertura de panela com retorno de aço. Desta forma, o índice de trabalho das Máquinas de Lingotamento Contínuo (MLC’s) da ArcelorMittal Aços Planos América do Sul seria maximizado, e com possível melhoria no Rendimento de Aço. O modelo se encontra em fase de implantação e validação na MLC#3, onde foram definidos parâmetros com critérios de decisão de interrupção/antecipação de troca de panela.

Aug 17, 2017

By Timothy F. McConachy

Between April 2000 and April 2002, the Commonwealth Scientific and Industrial Research Organization (CSIRO) Division of Exploration and Mining has led 6 research expeditions totalling 160 days ship time in waters of Papua New Guinea, Vanuatu, Solomon Islands, Indonesia and Australia. Five expeditions were undertaken aboard the Australian research vessel Franklin following successful competitive research proposals, and the sixth used the Indonesian vessel Baruna Jaya VIII (see Table 1). In addition, two CSIRO participants joined JOIDES Resolution for the Ocean Drilling Program Leg 193 in the Manus Basin of PNG. The major scientific objective underpinning these expeditions was to locate and study present-day seafloor and sub-seafloor hydrothermal ore-forming activity in order to develop improved methods of exploring for ancient mineral deposits on land that originally formed by similar processes. The research has been supported financially by a number of Australian-based mineral companies, by Australian international aid agencies, and by appropriation funds from CSIRO, and was conducted in collaboration with researchers from Australia, Indonesia, Portugal, New Zealand, United States of America, South Korea, and the host nations. Building upon earlier successes in the 1986-1997 PACLARK-PACMANUS programs in the Woodlark and Manus Basins of PNG, we have sought to examine a wider range of geological settings in which ancient orebodies are inferred to have formed, including both volcanic and sediment-hosted environments. We have now visited volcanic arcs, fore-arc and triple-junction related submarine volcanoes, and back arc basins associated with convergent plate margins in the SW Pacific and SE Asia, as well as conceptual Mississippi-Valley-type targets associated with warm seeps at passive margins in the Great Australian Bight (see Figure 1). Surveys ranged from northern Sulawesi via far western Bismarck volcanic arc near PNG-Indonesia border, through the eastern Manus Basin and the Tabar-Lihir-Tanga-Feni chain in PNG, the western Solomon Islands festoon, the San Cristobal arc, parts of the Vitiaz arc, to the northern and southern New Hebrides arc in the Solomons and Vanuatu.

Jan 1, 2002

By Paul Zinner

Efforts to win an enriched manganiferous product from the Missouri Valley deposits of South Dakota have included an application of most known ore-dressing devices and have been largely unsuccessful. At least two methods showed some promise of success and were the subjects of detailed Investigation by the Bureau of Mines during the period from July 1945 to August 1947. A series of mining and beneficiation tests were undertaken to determine conditions under which the most feasible concentration methods could be employed and to define the limits of such applications in terms of the character of the final beneficiated product. In the absence of a significant current market for any conceivable product of beneficiation, the extent to which applied methods might be considered successful was measured in terms of ratios of recoveries to grade, regardless of the adaptability of such beneficiated products to further metallurgical or direct usage. The results of all investigations show that production of a shale-free, concretionary, manganese-bearing product by any known method requires great sacrifices in manganese recovery. Products of beneficiation, with specifications permitting some inclusion of shale, can probably be most effectively produced by methods employing specialized jigging equipment as the principal functional unit of a process.

Jan 1, 1949