Search Documents

By Paul J. Lewis

Estimation of the axial side shear resistance of drilled shaft rock sockets is directly related to the unconfined compressive strength of the bedrock. Commonly, the mean unconfined compressive strength value is calculated from a range of laboratory test results and is used to estimate the side shear of the bedrock. This paper presents the results from a full scale axial load test performed on an 8.5-feet-diameter drilled shaft rock socket, and compares measured side shear values to estimated values for two different rock strata. Measured side shear values correlated well with the design value calculated for the "strong" rock stratum, but did not correlate well with the design value calculated for the "weak" rock stratum. The mean unconfined compressive strength was used to calculate the side shear in both strata, but review of the laboratory data indicates that this value may not have been appropriate for the weak stratum due to a large variation in the laboratory test results. Also included in this paper is a discussion of the subsurface conditions, the laboratory test results, and the methodology used to design the drilled shaft rock sockets for axial and lateral resistance.

Jan 1, 2005

By Kazimierz Gwizdala

In recent years, in Poland the ATLAS piles have been successfully applied for some constructions near Gdansk. The piles have been used as foundations for housing and another areas of civil engineering, in delta Vistula geotechnical region, characterized by weak, highly compressible soils represented by mud and peat, lying in sub-surface layers, several meters thick. Usually below are dense sandy soils or gravel. In all cases, the base of ATLAS piles rested on sandy soils. The analysis of pile bearing capacity has been discussed and verified by static pile load tests (SPLT). The load-settlements characteristics obtained were satisfactory. In the paper, the results of geotechnical investigations as well as calculations and load tests are shown. The ecological aspects of ATLAS piles application within highly urban areas of the cities and complex geotechnical conditions are emphasized.

Jan 1, 2006

By J. L. Fuentes-Cantillana, Á. Rodríguez, P. Morillo

Evacuation operations from work places in the case of an emergency are the key to minimising the effects of catastrophic type accidents such as fires, explosions, cave-ins, floods, etc. The correct planning of these operations, having the necessary means for sounding alarms and communicating and suitable training of personnel are the key factors for guaranteeing successful evacuation. The article gives an analysis of the problem in the case of subterranean mining and various types of work developed by AITEMIN in this field, including the development of new alarm and communication means specially adapted to the characteristics of mining operations, development of tools for help in the preparation of emergency plans and experiences in the education and training of personnel.

Jan 1, 2003

The Bibliographic Data Base is the result of a literature search con-ducted as one task of the technology assessment of current and advanced logging techniques, sponsored by the United States Bureau of Mines. After compilation, the bibliography was converted to an automated form for ease of utilization, and to allow for maintaining and updating the data base. The data base covers articles, symposia, books, patents, corporate and government reports, and other literature concerned with some aspect of borehole logging from January 1969 through December 1975. Periodic up-dating will be necessary to keep the data base contents in step with developments in the rapidly advancing field of application of borehole logging to mining. Many bibliographic indexes were scanned for entries relating to the subject of interest, and those entries which were included in our data base contain a reference to the bibliographic index in which they were listed (see Section 2.4.7). With the aid of these indexes, a vast number of publications, including foreign reports and publications, have been scanned for works relevant to borehole logging technology.

Jan 1, 1976

By J. E. Conley

Available statistics show that the demands of the American chemical industry for sodium sulphate have been increasing slightly in recent years. The supply from domestic sources, particularly In the form of byproduct salt cake from the acid manufacturers, has been tending to decrease due to the growing manufacture of synthetic acid. Both hydrochloric and nitric acids are being synthesized from their elements. The natural result has been that a smaller amount of salt cake is available. Simultaneously, the expansion of the Kraft paper industry, especially in the South, has brought about greater demand for sodium sulphate in that section. This dean is being met by domestic byproduct salt cake, by imported German sodium sulphate made from potash waste liquors, and by favorable situated domestic deposits of Glauber salts and tile anhydrous salt, thenardite. No shortage of natural sodium sulphate exists in the United States, but usually such deposits occur in semiarid regions far removed from transportation facilities and from markets. Moreover, the major portion of the natural deposits is Glauber salt or mirabilite (Na2SO4 ? 10H20), which must be dried or dehydrated in order to meet consumer requirements. The water of hydration represents, roughly, 55 percent of tae total weight of the crude salts and therefore has a very important influence on transportation costs. In marry instances the cost of getting, even the dehydrated product to market is the deciding economic factor. Therefore, the recovery oil production of anhydrous sodium sulphate from plant-.waste liquors or from natural brines of suitable composition might be economically feasible. The U.S. Bureau of Mines, at its nonmetallic Minerals Experiment Station, New Brunswick, N. J., has, for a number of rears, been investigating the commercial possibilities of treating the complex saline mineral polyhalite (K2SO4?NgSO4?2CaSO4?2H20) for the recovery of potash and magnesia. Certain proposed processes (1, 2, 3, 4)4/ yield waste liquors that contain the bulk of the magnesium and sulphate originally combined as magnesium sulphate in the polyhalite molecule. Sodium chloride In limited concentrations is also present, as extensive beds of salt occur in strata overlying the polyhalite deposits. A typical waste liquor would contain:

Jan 1, 1936

By X. L. Huang

This paper deals with the experimental and theoretic study of the contact pressure beneath the deep foundation of Beijing International Hotel, The experiments have been carried out in project and in model footing 6.6m2. The result of measurements shows the contact pressure at the edge is greater than that at the center. The theoretic analysis on the base of elastic theorey is in good agreement with the test if the proposed assumption used.

Jan 1, 2010

By Otto Sandovel Zea

El compromiso de minería perfecta se limita no solo a la preservación del medio ambiente, sino a la prevención de riesgos por desprendimiento de rocas y aplastamiento en el interior de la mina. En ese sentido, el presente texto señala la factibilidad de minar a sección plena todos los tajeos a través de la simulación de las condiciones más favorables y desfavorables de la mina, determinando como la alternativa más viable la bóveda en arco. Dicha estructura otorga estabilidad a las labores de minado -en tanto da sostenimiento activo a través del (Shotcrete SFR y Pernos Hydrabolt), así como desarrolla mayor productividad y menores niveles de riesgo por desprendimiento de rocas, menores grados de sobre excavación y genera de vibraciones al haber implementado la voladura de Pre-corte en sus labores.

Sep 12, 2011

By M L. van Kampen

The Resource Management Act 1991 provides for activities to be classified as permitted, controlled, restricted discretionary, discretionary, non-complying or prohibited in district and regional plans. This paper looks at the use of the prohibited activity status to restrict, in particular, mining. Often the use of prohibited activity status for mining appears to have no basis other than the negative perceptions that the local community and/or the planner drafting the plan has toward mining and quarrying.   The paper will address the current appeal regarding the use of prohibited activity status now before the Court of Appeal, and the history to the litigation. The relevance of the outcome of the appeal to the minerals sector will also be explained.

Jan 1, 2007

By Gartrell H. W

During investigations of the treatment methods for ore from the Bird-in-Hand gold mine carried out at Kalgoorlie and at these laboratories, it was found that excess alkali caused a lowering of extraction by cyanide, the cause of this being attrIbuted to the presence of a small amount of oxidised lead compounds in the ore. The subject has been discussed by various writers,3 but no satisfactory explanation of existing facts has been put forward. The experiments described in this report have been carried out with the object of obtaining some insight into the chemical reactions underlying the effect of lead salts and alkalis in cyanidation.The formation of cyanide-insoluble coatings on gold during roasting with lead compounds is well known, but the adverse effect of alkalis in cyanidation of ore is *This paper represents work done under a co-operative agreement between the Commonwealth Council for Scientific and Industrial Research and the South Australian School of Mines and Industries.Published by permission of the Mining Advisory Committee, Commonwealth Council for Scientific and Industrial Research.

Jan 1, 1935

By P. Somasundaran, D. W. Fuerstenau

This article presents the results of an analysis of grinding of 1:1 mixtures of 4x8-mesh quartz and limestone in laboratory ball and rod mills. From these experiments, the amount of energy consumed in grinding each component of the mixture was determined. In the ball mill, limestone consumes slightly more energy than quartz in the initial stages of grinding, but as the grinding proceeds quartz begins to consume a slightly greater fraction of the energy. The postulate that the fraction of energy consumed by any material in a ball mill is proportional to its volume fraction has been shown to be approximately true. On the other hand, in a rod mill energy consumption by quartz and limestone is equal only in the initial stages of grinding, with energy consumption by quartz greatly exceeding that by limestone as rod milling proceeds. Preferential energy consumption in tumbling mills has been discussed in a number of papers. For example, from an analysis of the kinetics of comminu- tion in ball mills, Arbiter and Bhrany' obtained rate equations based on the postulate that only coarse particles are ground, indicating that fine particles are protected from the action of the balls by coarser particles. In rod mills this protective action is much more pronounced than in ball mills. Recent studies on the rod milling of limestone-quartz mixtures have shown that this protective action causes the mineral with the lowest grindability (quartz in this instance) to consume the greater fraction of energy. 2 However, in the ball milling of mixtures it has been postulated that the consumption of energy by one of the constituents is determined by its volume fraction within the mill. 3 Possibly this hypothesis may be a simplification of the ball milling of mixtures since the protective action suggested by Arbiter and Bhrany may result in some preferential energy consumption by one of the constituents of a mixture. The objective of this study has been to determine preferential energy consumption in laboratory ball and rod mills by analyzing size distributions of each material in the products obtained from grinding 1:l mixtures of quartz and limestone. MATERIALS AND METHOD The procedure for carrying out the tests on wet grinding quartz-limestone mixtures has already been described.'r3 In the present investigation, 1:l mix-

Jan 1, 1963

By Ervin E. Underwood

IT has been recognized for many years that dis-persed particles have great value in raising the creep resistance of metallic alloys. In fact, some of the most successful high-temperature alloys owe their superiority to this factor above all others. A recent observation by Glen1," indicates that even better high-temperature resistance to deformation results in alloys capable of two successive precipitation reactions. The ramifications of this finding are of great interest. Unfortunately, our understanding of the reasons for such notable improvements has not kept pace with technical developments. In an effort to uncover some of the basic facts governing strengthening by particles, a program was initiated at the Battelle Memorial Institute with the primary goal of comparing creep strengths in single-phase and two-phase (precipitating) alloys. The effects of precipitation from solid solution on the creep properties of alloys are generally such that the resistance to creep is increased. However, if alloys are heat treated to different degrees of hardness before creep testing, it is often found that those possessing the maximum hardness initially do not necessarily have the maximum creep resistance. Depending on the stresses and temperatures involved other structures may prove more desirable. Considerations of the above nature indicate the importance of defining the initial state of the alloy. Here, it was decided to start with quenched single- phase alloys in which precipitation and creep deformation proceed concurrently. Equipment and Experimental Procedures Preparation of the Specimens—Four 25 lb ingots were prepared from 99.999 pct Cu and 99.996 pct Al to compositions of 1, 2, 3, and 4 wt pct Cu. Spec-trographic and chemical analyses are listed in Table I. After heat treatments and intermediate reductions, the alloys were cold rolled to 1/8 in. thick sheet. The final cold reductions amounted to 50, 40, 20, and 10 pct for the 1, 2, 3, and 4 pct Cu alloys, respectively. The specimens for creep testing were machined into tensile flats 7 in. long, 3/4 in. wide (at the shoulders), and 1/8 in. thick. The reduced sections were 1/4 in. wide and 21/2 in. long. After heat treatments at 540°C to an ASTM grain size of 1 1, the specimens were quenched into water at room temperature, then electropolished in a glacial acetic acid and perchloric acid solution. The gage marks were Knoop impressions placed 2 in. apart on the reduced sections. Blanks of 1 x 1 in, were cut from the same sheets for the age hardening runs and were given the same grain size heat treatments. The specimens and blanks were stored in a refrigerator at —40°C until needed for testing. Creep Measurements—Creep tests were conducted in a constant temperature room which was maintained at 26° ±1°C. A split-type, hinged, vertical-tube furnace was mounted on a horizontal track so that the specimen could be enclosed suddenly. Thus, it took about 15 min for the specimen to come within 5°C of the test temperature. The temperature variation along the specimen was controlled to about

Jan 1, 1958

By Edmund S. Leaver, R. S. Dean, T. L. Joseph

The metallurgy of manganese has developed along the lines of iron metal¬ lurgy. Enough high-grade ore has Been available so that by reduction with carbon it could be turned into an iron-ma.nga.nese alloy and a slag containing some 9 to 15 percent manganese. More siliceous ores have been smelted in the blast furnace to form iron-silicon-manganese alloys called spiegel. When lower-grade ores came in for serious consideration, which lias only been since l°l4, two types of processes received the most consideration — hydrometallurgical processes to produce a concentrate which could be smelted like the higher-grade ore and processes involving concentration of the manga¬ nese from manganiferous iron ores by preferential reduction of the iron (184)1. Special chapters in this bulletin are devoted to the production of ferro¬ manganese from ore, the hydrometallurgy cf manganese, and the Bureau of Mines modification of the preferential reduction process. Other methods of producing manganese alloys from low-grade or refractory ores have been suggested and may find future application. Manganese has a very high affinity for sulphur and is particularly adaptable to concentration by matte smelting. According to Betts (26), manganese silicate may be smelted with pyrite to give manganese sulphide and iron silicate. This method would be applicable to concentration of either the silicate or carbonate ores. The sulphide, once obtained, could be roasted to oxide and reduced in the usual way. Another possibility for the production of manganese from silicate ores involves their reduction by silicon or manganese silicides. Swedish Patent 52290, February 25, 1925. covers the reduction of a slag rich in manganese by silicon-manganese alloy containing more than 10 percent silicon, Joseph H. Brennan (38.) describes the concentration of manganese iron ores by partial reduction with silicon. Beckett (7,4,19) describes the reduction of manganese dioxide with a manganese silicide for the production of standard ferromanganese. Beckett gives as a typical alloy, manganese 64.4, silicon 24.6, and as a typi¬ cal ore, 5S.5O manganese as MnO^. The product of the reaction between these two is 80.11 percent manganese and 1.22 percent silicon.

May 1, 1934

By J. S. Duval

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). The compilation of the National Uranium Resource Evaluation aerial gamma-ray data to produce maps of the apparent surface concentrations of potassium, uranium and thorium for the conterminous USA has resulted in a reasonably accurate representation of the distribution of these elements in the surface rocks and soils. This claim is supported by the general agreement between the mapped geology and the patterns seen in the data

Jul 1, 1991

By D. A. Buckingham

Engineering and economic evaluations were performed by the Bureau of Mines on 14 Frasch sulfur, 1 native sulfur, and 21 metal sulfide operations in 11 market economy countries. The evaluation included discounted-cash-flow rate-of-return economic analyses at 15 pct to determine the average total cost of production of these two commodities and the potential availability of elemental sulfur (8) and pyrite concentrate. The Bureau evaluated the potential availability of elemental sulfur and pyrite concentrate. Approximately 279 million metric tons (Mmt) of pyrite concentrate at 46 pct 8 is potentially recoverable from 422 Mmt of in situ metal sulfide ore. Nearly 89 pct of the total pyrite concentrate is available at an average total cost of production below the January 1984 pyrite concentrate market price ($43/mt). About 185 Mmt 8 is potentially recoverable from 253 Mmt of in situ elemental sulfur. About 99 pct of this sulfur is available at an average total cost of production below its January 1984 market price ($131/mt).

Jan 1, 1986

By F. H. Edmunds

LLOYDMINSTER is the centre of a well developed agricultural area, lying on the Alberta-Saskatchewan interprovincial boundary in Township Fifty. The surrounding country is gently undulating, without any notable topographic features, but twenty-two miles to the north the North Saskatchewan river, and thirty miles to the south the Battle river, have cut deep valleys. In the spring of 1934, a wild-cat well (Lloydminster Gas Company's No. 1 well) was successful in striking a large flow of gas at a depth o 1,974 ? feet. The gas was piped into the town, a short distance south, and Lloyd-minster became the first Saskatchewan town to be served with natural gas. Following this discovery, other wells were sunk and, up to the present, thirteen wells have been drilled m what is here designated the Lloydminster area. Ten of these wells are in Saskatchewan and three in Alberta. Seven were successful in obtaining gas, three oil, and three have been unsuccessful. The area tested by this drilling is about eight thousand acres, six thousand of which can be considered as proved gas or oil land. To the south and west of Lloydminster, in the Province of Alberta, there are several areas in which oil and gas have been discovered. The Wainwright field lies nearly fifty miles to the southwest; Battleview, where recently gas has been discovered, is thirty miles west-southwest; and the Ribstone area is about thirty miles south and a little west. At Ribstone, a number of wells were drilled some years ago and there is a small production of oil. The data relating to the wells in the Lloydminster area that are recorded in this paper are taken from the records of the several companies operating in the field. The names of these companies are given on the map and on the type stratigraphic section (Figures 1 and 2). The author wishes to record his appreciation to Mr. R. H. Shaw and Mr. 0. C. Yates, both of Lloyd-minster, for much valuable information; also to Mr. E. Swain, of the Department of Natural Resources, Regina, with whom the writer has visited the field on several occasions, and who, by his enthusiasm and encouragement, has done much to forward the development of the area. The well samples were examined at Ottawa by officers of the Borings Division of the Geological Survey of Canada, who also made the interpretations of the logs. Frequent references will be made to the work of Dr. G. S. Hume, of the Geological Survey, and the writer would like to pay tribute here to his work.

Jan 1, 1940

By Peter Grundy

La eficiencia de los recursos en los procesos transparentes de gestión de las empresas permite aumentar el valor de los accionistas. En ese sentido, el presente texto señala el uso de la RCM como estrategia en el funcionamiento de un equipo que se centra en la confiabilidad. RCM es un proceso lógico que involucra aspectos técnicos y de negocio, capaz de producir resultados a muy corto plazo. Este proceso concluye con una recopilación de documentos fiables y totalmente óptimos para el desarrollo de las funciones de mantenimiento. Su uso correcto en la evaluación de los requisitos de mantenimiento de los equipos existentes, genera un mantenimiento menos costoso, confiable y eficaz. Asimismo se disminuye los costos de mantenimiento y se relaciona los aspectos ambientales y de seguridad.

Jul 17, 2000

By Emad Iskander

The seepage forces generated around pressurized water tunnels in rock are investigated using the analysis tools of geomechanics. The theoretical background of the two-phase material behavior is explained and the equations of motion and continuity are presented. Applications on two case studies typically occurring in practice deal with the required minimum rock cover for a pressurized tunnel and the separation between two tunnels carrying different heads. The rock mass behavior as described by the Mohr-Coulomb and Hoek-Brown material models is investigated by numerical analyses and the results are compared. The effect of key material parameters on the safety factors and the associated modes of failure is discussed.

Jan 1, 2008

By Luiz Alberto dos Santos, Rayander Martins Pimenta, Gláucia Domingues, Rafael Humberto Mota de Siqueira

Neste trabalho, amostras de NiTi com a composição de 50,9% at. Ni passaram por um tratamento superficial a laser Nd:YAG. O objetivo desde trabalho foi de modificar a superfície das amostras para comparar o parâmetro de rugosidade média (Ra) entre as amostras que sofreram interação do pulso do laser e a amostra que não passou pelo tratamento superficial a laser, já que para algumas aplicações biomédicas a superfície do material precisa ser rugosa. Para tanto, o laser foi utilizado em condições de velocidades de avanço diferentes. A amostra tratada com a menor velocidade de avanço laser, de 12,5 cm.s-1, apresentou uma maior rugosidade (Ra de 210 nm) devido ao maior tempo de contato do feixe com a superfície da amostra e, além disso, observou-se a formação de óxidos na superfície da amostra.

Oct 17, 2019

By L. Sturkey

Quantitative X-ray diffraction studies of the precipitation of thorium in a Mg + 3.3 Th + 0.51 Zr alloy (HK31A) in both the as-cast and cold-worked states show that the precipitation may be described by f = 1 - e(t/T)1/2 over most of the aging period. The effects of cold work and temperature changes are determined. The precipitation of tile equilibrium Mg-Th compotund is Preceded by the formation of a transition phase of higher thorium content, with the cowposition Mg2Th and with a Laves-phase structure. Thorium-containing alloys of magnesium have assumed considerable commercial importance, especially for applications requiring exposures to temperatures greater than 500°F for appreciable lengths of time. The principal commercial wrought alloys in this system are HK31A, containing nominally 3 pet by weight thorium and about 0.7 pet by weight zirconium: and HM21A. containing 2 pet by weight thorium and 1 pet by weight manganese. These two alloys retain a high level of properties even after exposures of 100 hr at 600°F, while the more common alloys containing aluminum and zinc are badly overaged by these conditions. Therefore, in order to obtain some insight into the mechanism by which thorium produces high temperature stability in these wrought alloys, it seems desirable to investi- gate the effect of temperature and mechanical working on the precipitation processes involving thorium. Since the scattering power of a thorium atom for CuKa X-ray radiation is about ten times that for a magnesium atom, the magnesium alloys containing about 3 pet by weight thorium are ideal for quantitative measurements by X-ray diffraction of the amount of Mg-Th compound present at any time. Such quantitative measurements should be of theoretical importance in the study of the effects of time, temperature, and deformation on precipitation and precipitation hardening. Of the two commercial alloys, HM21A and HK31A, the latter is certainly the most suitable for study: In the Mg-Th-Zr2 system, only Mg-Th compounds need be considered, since no ternary compounds or binary Th-Zr3 and Mg-Zr4 compounds exist. The Zr is added to this alloy as a grain refining agent and probably plays a secondary role in precipitation. On the other hand. thorium and manganese form many

Jan 1, 1961

Keywords: Pyrometallurgy, Pretoria University Substantial research in pyrometallurgy at the University of Pretoria started in 1980 with the appointment of Rian Dippenaar to the Iscor Chair, a position that he held until 1996, when Chris Pistorius became the leader of this pyrometallurgy group. This paper reviews the main research themes over the quarter-century from 1980 to 2005, as well as some of the industrial developments that have shaped the research approach. The main topics have been the use of electrochemical sensors for equilibrium measurements, ilmenite smelting, steel processing, and reduction.

Jan 1, 2006