Search Documents

By Patrick R. Taylor

A non-transferred arc thermal plasma assisted cyclone reactor has been designed, built and operated to evaluate its use in vitrification of wastes. Simulated waste (liquid, slurry or fine particulate) is injected near the plasma flame, where nearly instantaneous dehydration and calcination reactions happen. A non-transferred arc plasma torch was attached tangentially to the cyclone and is utilized as both an enthalpy source and to provide the gas velocities required to generate the cyclonic gas flow patterns. The closed top cyclone flow sends the solid particulates to the wall, where they are captured by a thin film of molten glass that is injected as a powder at a position lower in the reactor. The molten glass is then collected in a crucible. The feasibility of simulant injection directly into the flame zone and its effect on electrode lifetimes has been studied. Several candidate refractory systems have been evaluated for their suitability for extended use under the demanding conditions present in the cyclone reactor.

Jan 1, 2002

By Heikki Tuovinen

The total utilization of raw materials and energy is the most important criterion when planning. industrial processes. The main goal is clearly to use the raw materials and energy as effectively as possible in order to make the desired products directly in the primary process itself', or to recycle unused materials and energy either as such, or after cleaning back into the process. However, few industrial processes are so straightforward. Most processes generate by-streams of materials and energy, which cannot be recycled directly and it is namely these by-streams which tend to remain as wastes. These by-streams are slags, dusts, vaporized metals, liquids, slurries, sludges, gases etc. Most base metal processes produce all these by-products. Waste water and gas emission controls and regulations are tightening all the time, so new processes must be developed to keep pace with these requirements. These processes generate more solid wastes, which must be utilized or at least processed into a harmless form landfilling. Municipal and hazardous wastes also contain valuable materials and energy, which must be used to minimize landfilling. The development of processes for these purposes places even greater demands on research and development. The same principles and methods developed for mining, ore dressing and metal refining processes can also be adapted for research and development work on processes for waste minimization. However, the problems encountered are much more complicated and less familiar, demanding more versatile and accurate tools and equipment. This paper presents principles, examples and some references of R & D work on processes for waste minimization.

Jan 1, 1992

By Joo Hyun Park, Soo Sang Park

The distribution behavior of Pb between molten copper and FetO-SiO2 (-CaO, Al2O3) slags was investigated at 1473 K (1200 oC) and p(O2)=10-10 atm in view of the reaction mechanism of Pb dissolution into the slag. The distribution ratio of Pb (LPb) decreases with increasing CaO content (~6 mass pct) irrespective of Fe/SiO2 ratio (1.4~1.7). However, the addition of alumina into a slag with Fe/SiO2=1.5 linearly decreases the LPb, whereas a minimum value is observed at about 4 mass pct Al2O3 at Fe/SiO2=1.3. The log LPb continuously decreases with increasing Fe/SiO2 ratio, and the addition of Al2O3 (5 to 15 mass pct) into the silica-saturated iron silicate slag (Fe/SiO2 < 1.0) yields the highest Pb distribution ratio. The log LPb linearly decreases by increasing the log (Fe3+/Fe2+) value. The Pb distribution ratio increases and the excess free energy of PbO decreases with increasing Cu2O content in the slag. However, from the viewpoint of copper loss into the slag, the silica-saturated system containing small amounts of alumina is strongly recommended to stabilize PbO in the slag phase at a low Cu2O content.

Jan 1, 2014

By Masami Taguchi

"It is found that lead monoxide, PbO, has an ionic conductivity, and the all solid-state electrochemical cell using this oxide as an electrolyte has attracted the attention of battery researchers. In this study, thin film PbO2/PbO/Pb solid cells were produced on glass substrates and their discharge properties were investigated. The acti.ve material for the positive electrode, PbO2, was obtained by reactive sputtering of a Pb target in oxygen plasma. The PbO electrolyte and the active material for the negative electrode, Pb, were vacuum evaporated from /3 -PbO powder and a Pb block, respectively. The open-circuit voltage of the cell agreed with the theoretical value based on the thermodynamic data, and the close-circuit voltage was improved by the addition of a univalent impurity such as sodium or potassium to the PbO electrolyte. The connection of the cells in series and in parallel produced a higher electromotive force and a larger capacity. Also, the charge-discharge cycling test revealed that the cell could be charged and function as a storage battery.IntroductionGenerally, the ionic conductivity of a solid-state electrolyte is lower than that of a liquid electrolyte near room temperature. This has been a serious obstacle to using such electrolytes in an electrochemical cell. However, some solid-state electrolytes, which can preferentially pass a specified ion and have high ionic conductivity, have been found. Lead monoxide, PbO, which is an oxygen ion conductor, is such an example (1)(2). If a solid-state electrolyte is adopted for use in an electrochemical cell the problem associated with a liquid electrolyte such as leakage can be alleviated. The cell structure also can be simplified, because the electrolyte plays the role of separator to prevent the active materials from mixing. Thus, physical vapor deposition technology may make it possible to develop a very thin film cell, which consists of only solid phases (3)(4). In this study, the thin film PbO2/PbO/Pb solid cell with a thickness· of only a few micrometers, in which all the constituents were systematically deposited on a glass substrate by reactive sputtering and vacuum evaporation, has been produced and the charge-discharge properties were investigated. An attempt was made to improve the discharge properties by doping impurities such as Na2CO3 and Sb2O3 into the PbO electrolyte. Moreover, the connection of the cells in series and in parallel to get a higher electromotive force and a larger capacity, and the charge-discharge cycling test to determine its use as a storage battery were carried out."

Jan 1, 2000

By S. M. I Kytö, J .. K. Mäkinen, K. Saarhelo

"At the Outokumpu Oy Harjavalta Copper Smelter the control philosophy of the flash smelting process has been changed from the slow feed-back control to feed-forward control. This is important as the fluctuations in the flash smelting furnace matte grade and slag temperature are desired to be minimized.The system is based on a specially designed automatic sampling device and the Outokumpu Courier 20 on-stream X-ray fluorescence analyzer. A microcomputer-based Analyzer Operator Station (AOP) controls the system and calculates the process parameters for the furnace from the analyzed chemical composition and other existing data.A considerable reduction in the deviation of the matte grade and slag temperature has been gained. This has resulted in conservation of energy and refractories, lower copper losses and higher through-put in the flash smelting furnace and converters.1.0 IntroductionThe flash smelting technology for copper concentrates was developed at the Outokumpu Oy Harjavalta Smelter soon after the World War II. The incentive for this development was shortness and high price of any form of energy. The fact that smelting can be carried out autogenously, without external energy by utilizing the latent heat of sulfide combustion was known decades before, but Outokumpu Oy was the first company to take the advantage of this knowledge in practical operation. A further advantage of this technology was that the SO2 containing gases suited well for sulfuric acid production, thus minimizing the detrimental effects on the environment (1).The very heart of the flash smelting process is the reaction shaft of the flash smelting furnace (see Appendix I). Heating up of the dried feed mixture, dissociation of several compounds, ignition and oxidation of the feed take place very intensively in the reaction shaft during 2 - 3 seconds, which the fine grained particles reside in the reaction shaft. A very accurate control of the amounts of the feed materials as well as of oxidizing gases, fuel, etc. is of primary importance."

Jan 1, 1989

The U.S. Bureau of Mines investigated CaF2-assisted H2SO4 leaching to extract Mn from domestic silicate manganese resources. A pyroxmangite ((Mn,Fe)Sio3) ore containing, in pct, 34 Mn, 23 Si, 3 Ca, and 1 Fe was leached at 90° C for 3 h in a solution containing, in g/L, 12 Mn, 140 H2SO4, 130 (NH4)2SO4, and 5 CaFz. Manganese extraction of 92 pct was achieved. Manganese of greater than 99 pct purity was prepared by electrolyzing the purified pregnant solution at a current density of 50 mA/cm2. The current efficiency was 65 pct.

Jan 1, 1991

By Jiang Feng, Li Chuanhua, Zhang Libo, Peng Jinhui, Ju Shaohua

Solvent extraction of Cu2+ from the leaching liquor contain Cu and Fe use a microfluidic technology. Currently, the conventional copper extraction process has many problems such as long distance and small driving force of mass transfer. In order to solve the problems, studies are carried out on the extraction process of low grade copper leaching liquid using Lix984N as an extractant with a new microfluidic solvent extraction technology. The effects of flow rate on the separation and extraction efficiency between Cu and Fe are studied, and the results show that a steady liquid-liquid interface of laminar flow is form in the micro-extractor, and extraction efficiency is 78 % and 2.5 % for Cu and Fe at the contact times of 0.84s respectively. Besides, the separation coefficient between Cu and Fe is as high as 140.04. The studied microfluidic technology has the advantages like improving extraction efficiency and reducing reaction time and providing the potential application in the hydrometallurgy extraction of Cu.

Jan 1, 2015

By S. H. Castro

The El Teniente molybdenite plant (Chile), with a nominal capacity of 3,200 tpd of bulk Cu-Mo concentrate, produced approximately 3,385 metric tonnes of Mo during 1998 by using the phosphate Nokes process (LR-744 reagent). This is the only Chilean moly plant which traditionally has depressed copper and iron sulfides with LR 744 reagent, which is a hydrolysis product of P2S5 and NaOH. El Teniente&apos;s ore Mo grade is 0.02%Mo and is concentrated to 0.45%-0.50% Mo in bulk Cu-Mo flotation. Subsequently, molybdenite is floated by selective flotation to depress Cu and Fe sulfides, such as chalcopyrite, bornite, digenite and pyrite, to produce typically a 49%-50%Mo molybdenite concentrate. An optimisation program during the last two years was undertaken to improve molybdenite recoveries. Current molybdenite plant technology at El Teniente and use of phosphate Nokes in the process process is reported. Use of phosphate Nokes reagent has increased average Mo recovery from 70.5% in 1977 to a mean 74.7% for the first 4 months of 1999. The global Mo recovery, including bulk flotation, incresed from 42.3% in 1997 to 46.8% in 1998, with a projection of 55.5% for 1999. Mo production per year has increased from 3,181 tons in 1997 to 3,385 tons in 1998 and a projected 4,000 tons for 1999.

Jan 1, 1999

By Thomas Schuman, Jaan Kers, Lucas N. W. Damoah, Xiangjun Zuo, Lifeng Zhang

"Rapid technological innovation has propelled the use of electronic equipment leading to the generation of more and more waste electrical and electronic equipments (WEEE). Printed wiring board (PWB) is a component made of one or more layers of insulating material with electrical conductors. To investigate an environmentally friendly process to recycle PWBs, PWB samples with and without additives were pyrolyzed. Liquid, gas and solid products were achieved with different conversion fraction. Analysis of the exhaust gases from the experiments using GC-MS and MS showed that without CaCO3 additives poisonous gases such as C6H6 and HBr were produced which were adequately controlled if CaCO3 was added.IntroductionPyrolysis is one of the best methods for treating complex mixtures of waste polymers and to recover the material and energy content. The process consists of thermal decomposition at moderate temperatures in total absence or small amount of oxygen in which the structures of polymers break down into smaller intermediate products "". The decomposition temperature of a substance is the temperature at which the substance breaks up into smaller substances or into its constituent atoms 2). Thermal treatment of PWBs were reported using DC Arc Plasma furnace 3), and fixed bed reactor 4). One drawback in dealing with thermal treatment of PWB scraps is the likely production of super-toxic halogenated dibenzodioxins and dibenzofurans from the bromine containing structures. Pyrolysis of organic materials contained in waste PWBs leads to the formation of gases, oils, and chars which can be used as chemical feedstock or fuels ""'. Dehalogenation of the pyrolysis product of electronic scraps is essential to make it commercially acceptable. It would be obviously the most advantageous solution as pyrolysis and dehalogenation are carried out simultaneously. Reported pyrolysis investigations are at experimental stage and have been carried out in vacuum, molten salt, fluidized bed, rotary kiln, entrained, stationary, and moving bed reactors 7). Comparing to the incineration and combustion of PWBs, the pyrolysis process has several characteristics: 8'"">) 1). Converting the organic solid substance into fuel gas, fuel oil and carbon-black as storage energy; 2) Emitting toxic substances such as sulfur, bromine and heavy metals in wastes; and 3) Keeping metals from being oxidized. Although many researches into the pyrolysis of PWB wastes have been reported, most of the works have been carried out using analytical pyrolysis techniques or very small batch reactors ""~'5). Also, most of the works for the pyrolysis of PWBs haves concentrated on the composition of the organic products, particularly the brominated organics. The current study is to investigate the pyrolysis of PWB powders in a small TG-DTA scale and a 50-gram tube furnace scale."

Jan 1, 2011

By S. Neogy, M. Gupta, D. Srivastava, V. Kain, S. Roychowdhury, R. C. Prasad, G. K. Dey

"Austenitic stainless steels are an important material of construction for Boiling Water Reactors (BWR). These stainless steels are amenable to strengthening by strain hardening. Various deformation modes at different test temperatures and strain become active. In the present investigation type 304LN stainless steel was used in the annealed and strain hardened condition. Thin foils were prepared from gauge section for transmission electron microscope (TEM) investigation after tensile testing at room temperature and at 288°C. TEM investigation reveals that twinning is the major mode of deformation for the tests done at room temperature while dislocation cross-slip is the major mode of deformation at higher temperature. Stacking faults were also observed to a limited extent. The extent of twinning was much higher for the tests done using the rolled material. The formation of martensite in the stainless steel due to straining was investigated by the analysis of selected area diffraction patterns.IntroductionAustenitic stainless steels (type 300 series) are an important material of construction in Boiling Water Reactors (BWR). These stainless steels cannot be heat treated but can be strengthened by cold working [1]. Nitrogen alloying of these stainless steels result in high strain hardening rates and higher strength without any loss in toughness [1]. Stress Corrosion Cracking (SCC) in BWR of these types of stainless steels have been attributed to surface strain hardening and strain hardening ofregions adjacent to constrained weldment [2].The test temperature [3, 4], prestrain [5] and nitrogen level [5] has been reported to affect the deformation mechanism during tensile testing. Byun et al. [3] have reported the formation of martensite, dislocations, stacking faults and twinning during tensile deformation, the extent of each depending on the test temperature. Strain localisation has been reported to occur during tensile deformation in irradiated stainless steels [ 6]. The behaviour of rolled material during tensile testing is similar to that of irradiated material to a large extent [3]. Austenitic stainless steels are low stacking fault energy (SFE) materials in which various types of microstructures have been reported to form during tensile deformation and the strain is also highly heterogeneous in nature in these stainless steels which aides SCC in BWR environment to a large extent [7]. During cold working of austenitic stainless steels second order twinning has also been reported [8]. Knowledge about the deformation mechanisms operative in the strain hardened austenitic stainless steels during tensile testing at different temperatures is essential to understand the material deformation behavior and the present study aims at enhancing the existing understanding."

Jan 1, 2011

By Torma A. E.

Biotechnological processes are considered to be cost effective especially for situations where the recovery of metals from &apos;Very large volumes containing trace metal concentrations (less than 10 ppm) is concerned. Microorganisms, alive or dead, or their products can be highly efficient and selective biosorbents for metal concentration. It is important that the metal bound to the biosorbent can be stripped by suitable agent(s) and regenerated for repeated use. The stripped solution should be concentrated enough to be introduced into the common metal recovery circuit. The industrial acceptance of biosorption processes is dictated by increased competitive advantage over other processes. This paper reviews the pertinent literature?, regroups the information, and points out future possibilities for the mineral and metal processing industries.

Jan 1, 1992

By Joël P. T. Kapusta, Romeo U. Pagador, Noparut Wachgama, Chumnoom Khuankla

"Thai Copper Industries (TCI) is a custom copper smelter and refinery in Rayong, Thailand, with an annual capacity of 165,000 tons of cathodes. It employs the El Teniente Technology as the primary smelting reactor to produce white metal from copper concentrates. The white metal is further treated in Hoboken Siphon Converters to produce blister copper then refined in anode furnaces before being cast into anodes for electro-refining in the on-site tankhouse.Thai Copper Industries is the first copper smelter to install and successfully operate on a commercial scale with the Air Liquide Shrouded Injection (ALSI™) Technology in the Hokoben converters with sonic injection of oxygen enriched air and nitrogen for cooling of the injector tip areas. Following commissioning and the establishment of operating practices, the performance of the Hoboken converters with ALSI™ Technology produced outstanding results. The unique combination of an El Teniente and Hoboken siphon converters, both of which are bath smelting operations, offers very high blowing and oxygen efficiencies. As a consequence, reverts recycling was accelerated with minimal build up on the mouth, end-plates or even below the siphon that is typical in Hoboken converters.These outstanding results in the Hoboken Siphon Converters with ALSI™ Technology helped the TCI Plant reach a production of about 75% of its capacity within four months despite the fact that the TCI staff is quite young and its converter know-how and experience are not yet fully developed."

Jan 1, 2009

By Yan Fu, Chuanlin Fan, Xiujing Zhai, Yongfeng Chang, Binchuan Li

"The mechanism of the selective chlorination of nickel and cobalt in reduced limonitic laterite was investigated. Reduced ores were obtained from the reduction roasting of a limonitic nickel laterite. The thermal decomposition of related chlorides and the selective chlorination of the reduced ore were carefully studied using Differential Thermal analysis - Thermogravimetry (DTA-TG), X-Ray Diffraction and chemical leaching methods. In the temperature range of 300 - 500 °C, aluminum chloride hexahydrate was chosen as chloride agent. During the selective chlorination, reduced ore was partly chlorinated by hydrogen chloride generated from the thermal decomposition of chloride agent. Then the oxydrolysis of ferrous chloride re-generated hydrogen chloride was used to further the chlorination. Finally, iron was mostly rejected as hematite, while nickel and cobalt were selectively chlorinated. More than 91 %Ni , 90%Co and about 4%Fe in the chlorinated ore was extracted using a water leaching method.IntroductionLimonitic nickel laterite is an important nickel reserve, which is rich in iron in the form of goethite and has low contents of magnesium, aluminum, silicon, and other elements. Goethite is the main nickel-bearing mineral in the laterite [1]. Nickel is generally present in goethite in three modes: (a) associated with amorphous or poorly crystalline goethite, (b) weakly adsorbed to the crystalline goethite surface, and ( c) as lattice substituents [2]. In addition, cobalt in limonite was found to be associated with a manganese phase rich also in nickel [3]. These results indicate that the extractions of nickel and cobalt are highly dependent upon the degree of the decomposition of the nickel, cobalt-bearing minerals.For the selective extraction of nickel and cobalt from limonitic laterite, the ore is usually processed by hydrometallurgical methods, including high pressure acid leaching (HPAL) [4] or reductive roasting - ammonia leaching (Caron process). However, there are still some disadvantages in these processes, such as the expense of autoclaves and scaling problems in HP AL [ 4, 5], and relatively low overall metal recovery, large energy and reagent requirements for the Caron process."

Jan 1, 2011

By Thomas J. O'Keefe, Pu Yu, George Houlachi, Xuewen Tang

"Impedance measurements were used to investigate the electrochemical characteristics of acidic zinc sulphate electrolytes containing Sb3+, gelatin and their mixtures. The data were correlated with cyclic voltammetry curves made using synthetic as well as industrial electrolytes. The cyclic voltammetry results were similar to those obtained in previous studies in that antimony caused a depolarizing effect while gelatin gave an increase in the potential for zinc nucleation on an aluminum substrate.The electrochemical impedance spectroscopy (ElS) evaluations were conducted on electrodeposited zinc at three overpotential values. The potentials were chosen to represent various current density regions in the zinc polarization curves. The antimony and gelatin gave characteristic impedance plots which correlated with expected behavior, particularly current efficiency. Both antimony and glue appear to modify the intermediate zinc reaction sequence, but in different ways. The data strongly suggest that film formation and stability are major factors in the zinc ion reduction mechanism.IntroductionThe zinc electrodeposition process is sensitive to the presence of a variety of organic and inorganic chemical species in the electrolyte [I]. Such components can produce either beneficial or harmful effects, depending on their relative concentrations and electrochemical behavior. Extensive investigations have been made to gain a better understanding of the changes occurring during zinc deposition in the presence of such additives. Techniques employed include microscopy, x-ray diffraction, dynamic voitammetry, current imd energy efficiency studies [2-5]. Ultimately, the objectives are to identify the factors which most affect the efficiency of the process and to provide a means to effectively control them.One of the most harmful impurities is antimony, which can be detrimental when present at concentrations as low as 10 to 20 parts per billion. Dramatic changes in zinc polarization behavior, deposition structure and current efficiency have been observed with antimony in the electrolyte. Antimony appears to lower the hydrogen overpotential by hydride formation or a similar catalytic mechanism, which allows an increase in localized corrosion and zinc dissolution [6-8]."

Jan 1, 1997

By C. G. Bastos Andrade, V. F. Justo, F. R. Valenzuela-Diaz, M. G. S. Valenzuela, C. M. Matos, C. Volzone

For industrial use, the smectite clays are usually treated with inorganic acid of high concentration at temperatures under boiling point, which provide the bentonite´s bleaching power. In the present paper, a sample of brown smectite from Paraiba, Brazil, was submitted to treatment under moderate conditions (90°C, reaction times of 1, 6, 12, 18 and 24hours in close reactor, concentration of the aqueous solution of hydrochloric acid 1.5M, clay/acid solution ratio of 1g/10mL), aiming to reduce impurities, responsible for the color of the clay, without causing significant changes in their structure. The samples were characterized by scanning electron microscopy (SEM), energy dispersive X-ray detector (EDS), stereomicroscopy, Cation Exchange Capacity (CEC), Thermal Analysis (TG/DTA), and X-ray diffraction (XRD). It was observed a bleaching in samples with time of 12h to 18h. With the DRX was possible to monitor the peak intensity of the clay structure and the sample with 12 hours of treatment was not significantly altered its crystalline structure, maintaining the peak clay at d(001). The most pronounced changes in the bleaching occurred within the first 12 hours of acid treatment. Thus, clay can be used in products with high added value.

Jan 1, 2015

By D. P. Cook, Jr. Jones, J. W. Evans

"It is well understood that the flow of liquid metal in the mold region of the caster can have a notable effect on the overall solidification behavior in aluminum casting. Previously our group has characterized the flow in this region in a water model, using particle imaging velocimetry. The flow is significantly effected by the specifics of the metal delivery system, i.e. size, geometry, used during the cast. Recently, a time-averaged 3D numerical model of the nozzle, combo bag and sump region has been developed and its validity has been tested against experimental data. Cases were run for different sized combo bags as well as bags that have been blocked. The results show satisfactory agreement between the physical and mathematical models.IntroductionFluid flow in the head of an electromagnetic (EM) and direct chill (DC) ingots has been shown to effect many important operational parameters in casting such as superheat removal, macrosegregation, and hot cracking. In most cases, the momentum from the nozzle is diverted through a delivery system, termed a bag, before entering the mold region. The specific geometries of the bags vary widely from operator to operator suggesting that there is still some question as to the optimum design. Several studies [1-4] have been carried out to understand the influence of the bag design on the solidification behavior in aluminum casters. However, few studies have included numerical prediction with experimental verification. Unfortunately, many simulations performed today still do not accurately account for flow in such devices.Recently, a significant amount of research into the flow resulting from the metal delivery systems has been performed [5-8]. The thrust of this research has been characterizing the flow patterns by a measurement technique called particle imaging velocimetry. The data suggest that the method of delivering the liquid metal into the mold region has a significant effect on the nature of the flow. With a detailed set of quantitative data from a water model, a numerical model can be built and tested to ensure a proper description of the flow field. The computational model used in these simulations is designed to represent a laboratory scale model of a caster in which ""combo"" bags were simulated. Such bags are mostly of a densely woven glass fiber material with low permeability to aluminum. ""Windows"", of a more open weave, permit aluminum to flow from the bag, see Fig. I. Two different sized combo bags were modeled, each subject to two different outflow window configurations. Furthermore, experimental measurements [9] were used to validate the model results."

Jan 1, 1999

By Malti Goel

"The cost-effective capture of carbon dioxide (CO2) from the point sources for its reduction the atmosphere offers many challenges in materials science. Novel CO2 capturing approaches using chemical, physical and biological methods are in the research stage and are aimed to minimize the cost. Appropriate materials development , which can withstand required temperature or pressure as the case may be for CO2 emanating from coal gas or industrial waste gases form the minimum condition. Other requirements are reclyclability of material and cost of separation. Nano-material composites can be more effective in selective capture of CO2 and can offer solutions for large-scale separation process. Nano-porous material catalysis can enhance the reaction rate of CO2 with other chemicals and thus help in capture of CO2 and convert it into value added products. This paper reviews recent industrial scale developments. In the Indian context, R&D priority areas in CO2 capture process development with a focus on energy industry are presented.IntroductionScience of Climate Change is growing at an enormous pace. With the ultimate goal of stabilization of greenhouse gases in the atmosphere, new scientific approaches are being researched worldwide. A shift in policies from low carbon and no carbon energy sources to fossil fuel sources with capture of carbon and its permanent storage is taking place. The process of carbon capture is both energy and materials intensive and the cost of power generation may increase up to 40% when carbon capture and storage (CCS) technology is implemented. Development of cost effective R&D technology therefore remains the greatest challenge before the scientific community."

Jan 1, 2009

By Reza Ghomashchi

Casting is the most economical route to transfer raw materials into readily usable components. The economics of casting would be more pronounced and better realized, if there are no or limited necessary post fabrication treatments. Therefore, there is an urge towards near or net-shaped casting as there are significant advantages over conventional casting including reduction of component weight, excellent surface finish, higher strength and integrity of the as-cast parts, closer tolerance, and the ability to produce pore-free parts by controlling the solidification shrinkage. The concept of near or net-shaped casting is currently employed for both semi-finished products such as strip-casting and finished shaped casting, as in case of high pressure die casting or squeeze casting. The full potential of this process yet to be explored and is expected to be realized within the next 10 years, especially in case of strip casting. The current article discusses different near or net-shaped casting routes currently employed for fabrication of high integrity finished products with main emphasis on aluminum-silicon alloys. In this regard, attempts will be made to identify the key parameters during fabrication and highlight the importance of process control and optimization in fabricating premium quality cast products. Keywords: Near Net Shape casting, Solidification, die casting, squeeze casting, rheocasting, thixocasting

Jan 1, 2003

By Daniel Adolfsson, Ryan Robinson, Fenwei Su, Jelena Blagojevic

"Cold bonded briquetting of steel plant by-products has proven to be a viable recycling alternative concerning technology, economy and environment in both the traditional blast furnace route and the direct reduction process. A critical parameter in cold bonded briquettes is the type and amount of binder used during production. The binder material must meet certain quality requirements concerning low and high temperature strength, chemistry and economy. Currently, SSAB Tunnplåt uses ordinary Portland cement (OPC) as binder in their cold bonded briquettes. In order to improve binder quality and possibly decrease OPC dependency, a binder feasibility study has been conducted concerning an internal by-product, ladle slag, as a supplement and/or partial substitute for OPC. Several characterization techniques have been used to study the behaviour of ladle slag, these include: XRD, XRF, SEM, glass content analysis, calorimetric analysis, particle size distribution and thermochemical stability considerations concerning the CaO-Al2O3-SiO2 system.IntroductionRecently, a project was initiated at SSAB Tunnplåt AB, in Sweden, which aimed at reducing the amount of ordinary Portland cement (OPC) as hydraulic binder in cold bonded briquettes by partly replacing it with ladle slag. OPC is traditionally used within civil engineering, and widely accepted as a hydraulic binder in a number of different applications. OPC consists of four major crystalline phases, i.e. C3S, C2S, C3A and C4AF. Tricalcium aluminate as well as the ferrite phase in OPC reacts very quickly with water, for this reason gypsum is added to the clinker in order to retard these reactions. The fact that gypsum is present in the system limits the recycling of briquettes to the BOF, since the presence of gypsum during steelmaking results in a significant amount of sulphur emissions. The latter along with the expense that follows, makes it worthwhile to consider alternatives for OPC as binder in cold bonded briquettes."

Jan 1, 2008

By P. Tim Johnson

Relentless increases in demand for nickel and vanadium for uses such as steelmaking, catalysts and battery materials, plus the growing financial and environmental costs of their primary extraction, have led to much interest in potential secondary sources of these metals. The presence of such metals in heavy fuel oils, bitumen and related materials offers both opportunities and challenges for potential extraction methods, especially with the growing production and importance of metal-rich fossil fuels around the world. For several decades, Tetronics’ DC plasma smelting technology has been used for the recovery of metals such as nickel and chromium from stainless steel melt dusts and other wastes in compact, environmentally-friendly and efficient plants. This paper explores the suitability of DC plasma smelting as part of a wider flowsheet with feed preparation and aluminothermic reduction techniques for smaller-scale extraction operations based on this important niche secondary source of these key metals.