Search Documents

By A. González

Arsenic is one of the main contaminants present in Chilean copper concentrates and its abatement represents a challenge for the process metallurgy, particularly under the strong environmental requirements in the global community. The possibility to form ferric arsenate directly from a gas phase by means of a heterogeneous reaction between an arsenic gas bearing and iron oxide was studied at laboratory scale. A thermodynamical analysis for the system Fe-As-O-S has been initially made, in order to obtain the stability conditions for the ferric arsenate or other FeAsyO2 type compounds. Experiments were made using an hematite sample suspended in a thermogravimetric device. AS4O6 gas generated from solid AS2O3 that was passed through the iron oxide sample and its instantaneous weight change was recorded directly. A kinetic study for the AS4O6 volatilization was made to control the gas composition. A chemical control between 300 and 600°C with an apparent activation energy of around 14 Kcal/mol As2O3 was determined. The samples after the reactions were chemically and XRD analysed. Arsenates detected corresponds to complex compounds. Results shows a dependence on temperature and oxygen content in the gas phase. The kinetics for iron arsenates formation is slow, reaching an arsenic capture of 6% after 80 minutes of reaction when an oxygen content of 50% is fed continuously at 800°C and 3,56% As in the gas. Experiences made at the same temperature but under higher oxygen content in a closed reactor, allowed arsenic capture close to 60%. For higher temperatures the capture is considerably lower.

Jan 1, 2003

By Ole Rud Bendixen

Topsoe has developed a Wet gas Sulphuric Acid (WSA) process which effectively recovers SO2 in off-gases from non-ferrous smelters and roosters. The product is concentrated sulphuric acid of typically more than 96 wt% irrespective of SO, concentration in off-gas. The process does not generate any waste products or waste water and does not use any absorbents or other chemicals. In the process, up to 99.3% of the SO2 is converted catalytically into SO3, which reacts with water in the gas, hereby forming gaseous sulphuric acid. The acid is condensed in a WSA condenser of proprietary design. Excellent heat economy and practically no sensitivity to the water balance mean that no extra sulphur burning is required at any S02 concentration, The process is especially well suited for treating off-gases where the SO2 content is lower than approx. 5-6%, and it is a good alternative to a complete renovation of a smelter. However, also off-gas from flash smelter may be treated. The process has found good use in both molybdenum and lead roosters. An example from a molybdenum roaster in Chile shows that 97-98wt% acid is produced from a 2.3 % S02 gas. This plant is situated in the outskirts of Santiago and represented a major local source of SO2. The plan was started in May 1993.

Jan 1, 1996

By Ejike Emmanuel, Nwoye Chukwuka, Ogwuegbu Martin, Asuwaji Ayuk, Onyedika Gerald

"Microwave pre-treatment of cassiterite ore prior to leaching was carried out in an attempt to obtain high grade of Sn02 and to conserve the total energy expended during processing. Microwave treatment was selected due to the presence of associated minerals which behaves differently to microwave energy. Studies in this work showed that microwave pretreatment of cassiterite ore can be applied to increase the recovery of tin oxide within 5 minutes of leaching. Microwave treatment of the ore resulted in mineral liberation at all particle sizes. Tin oxide was separated from the major impurities via leaching in potassium hydroxide solution and precipitation, resulting in 98% Sn02 at pH 7.IntroductionIn the nineties, the available techniques used for ore processing and analysis in Nigeria was the solution methods of either alkaline fusion or acid digestion [1,2]. A process in which cassiterite is made acid soluble by reduction to SnO2 , which stabilizes by glass formation and the tin was extracted by leaching the glass with sulphuric acid, followed by electrowinning was reported [3,4]. In another study, Baba et al [5] studied the dissolution kinetics of a Nigerian casiterite ore in hydrochloric acid solution. The effects of acid concentration,temperature, particle size and stirring speed were examined. It was found that the dissolution rates of cassiterite depends on hydrogen ion concentration, H+, stirring speed and ore particle dimensions. These were believed to report low data due to incomplete solubilization of the ore minerals in aqeous medium [6]. Analytical chemists have used microwave heating devices routinely for the dissolution of metals, minerals and various chemical products in chemical analysis [7,8]. It offers faster heating rate and consequently faster dissolution rate than conventional heating. The principle of the dissolution of analytical samples has been applied to the leaching of various minerals contained in an ore or concentrate sample. Some researchers [9, 10] conducted microwave assisted leaching of laterite ores containing oxides of nickel, cobalt, and iron. The metals of these mineral components were converted into their chlorides by microwave heating (1200 W, 2450 MHz, Nz atmosphere) a mixture of the ore and ammonium chloride between l 77°C and 312° C for 4-5 min, followed by water leaching at 80° C for 30 min. Nickel and cobalt extractions were 70% and 85%, and respectively, and are comparable with roasting at 300°C in a conventional rotary kiln for 2 hours."

Jan 1, 2013

By Qingcai Liu

The effect of the TiC addition on corrosion resistance of the Al2O3-C refractories in smelting reduction melts has been studied by quasi-station immersion and rotary immersion. The corrosion rate of Al2O3-C refractories is decreased with the TiC addition. The corrosion mechanism of Al2O3-C refractories is oxidization of graphite carbon by the oxides of the melts and the formation of deteriorate layer.

Jan 1, 2006

By Anurag Tripathi, J. K. Saha, S. K. Ajmani, J. B. Singh

"The quality of steel is a major concern in the metallurgical industry. The control of liquid steel temperature can enhance the level of cleanliness in steel. Ladle is one of the major vessels used to transfer liquid steel between different stations. The heat transfer phenomenon taking place in this vessel needs to be monitored for controlling the liquid steel temperature. A CFD model was developed for prediction of liquid steel temperature during complete process cycle of ladles in direct heats. The model was validated with liquid steel temperature measured at on-line purging station and tundish during teeming from one of the actual steel plant. The accuracy of model was 96 %. The results obtained show insignificant effect of slag thickness, tapping temperature and ladle life on liquid steel temperature in the ladle. However, the importance of initial refractory temperature was noticed. The CFD model developed in present work can generate the thermal history of liquid steel and refractory walls of any ladle at any stage.1. IntroductionThe control of liquid steel temperature is desired to achieve required steel quality. The low casting temperature is detrimental and may result in nozzle blockages due to premature solidification in the tundish. The phenomenon of heat losses taking place in ladles needs to be understood for prediction of liquid steel temperature. The assessment of thermal profile of liquid steel from BOF converter to caster can be done through consideration of heat losses at all points. Hlinka and Miller [1] showed that the ladle pouring temperature varies due to heat losses from molten steel into surrounding refractory layers. The phenomenon of thermal stratification was numerically simulated by Ilegbusi and Szekeley [2]. The effects of slag cover on heat loss and liquid steel flow in ladle before and during teeming to a continuous casting tundish was numerically simulated by Chakraborty and Sahai [3]. Investigators also developed some simple models to predict the steel temperature for some of the processes taking place in ladles [4-9].The present work is an effort to generate the full information about the temperature drop taking place in any ladle throughout its process cycle. This information can be used to predict liquid steel temperature and to take decisions to minimize heat losses."

Jan 1, 2012

By Zhucheng Huang, Lingyun Yi, Bin Chai, Tao Jiang

"A high iron content manganese ore was reduced at 900~1200°C and followed by a magnetic separation process. SEM and EDS analyzes were employed to examine the transformation of microstructure and phase in reduced sample and the mechanism was revealed. Results showed that elements enriched during reduction. Iron existed in the metal iron phase and most of oxygen formed compound with manganese. Consequently a clear distinguish between iron phase and manganese minerals formed, which was beneficial to the separation of iron and manganese. But the iron phase can not be monomer dissociation in grinding process and manganese compounds turned into magnetic product as package and mechanic inclusion due to the isomorphism of iron and manganese and the small particle size. And MnO could be found partially in iron phase, which hindered the further separation of manganese and iron.IntroductionManganese is widely used in industry. The amount of manganese used in steel industry is very huge and 90% manganese is used in steel industry. Manganese ore resources are rich in China, yet with fewer rich ore but more low-grade ore which accounts for 93.6% and fine refractory ore. The constitution of the ore is very complex and more than 73% of all the manganese ore contains iron[l,2]. With the increasing of consumption of steel, the demand for manganese is becoming larger and larger and the imported ore accounts for more than 50%. Therefore, how to use the manganese ore efficiently has very significant meaning. The main method is manganese residual, which is simple and stable. However, the development of the method is limited by the quality of manganese ore, the huge amount of manganese residual, the technology of blast furnace process and economics[3,4]. Chemical benefication which may pollute environment and is difficult to recover iron is still being researched[5,6]. The paper investigated the process in which anthracite coal was the reducing agent for coal-based direct reduction and magnetic separation of the ore, and SEM with EDS measurements were employed to examine the transformation of phase in reduced sample and the mechanism was revealed[7,8]."

Jan 1, 2013

By Jong-Oh Jo1

Thermodynamics of Ti, N and O in liquid iron was studied in order to establish a data base for the prediction of TiN and TiOx formation in liquid stainless steels containing various alloying elements including Cr, Ni and Si as a function of temperature. The interaction parameters of these elements on Ti and N were determined using the metal-nitride-gas equilibration technique. The TiN stability diagram for a commercial stainless steel grade was constructed from the measured thermodynamic parameters, and its validity was confirmed experimentally. The interaction parameters between Ti and O, and the equilibrium constants for Ti deoxidation reactions for the formation of Ti2O3 and Ti3O5 were also determined by the equilibration of the melts with those oxides identified by the XRD and the EPMA analyses.

Jan 1, 2006

By J. J. Talja

An investigation of oxidation of various nickel concentrates was carried out using differential scanning calorimetry (DSC). The aim of this study was to determine the ignition temperature and investigate other oxidation behavior of various sulfide-based nickel concentrates. Variables in the experiments were mineralogy, particle size and partial pressure of oxygen with temperature increasing linearly at 25 K/min from 323 to 1023 K (50-750 °C). The igni¬tion temperature was determined to represent the starting point of rapid oxidation. The reac¬tion enthalpies of the concentrates were determined and the amount of heat generated up to various time were used to calculate the extent of reaction. Mineralogical changes at various stages of oxidation were also investigated. For this purpose a second set of DSC-experiments were carried out in which each experiment was interrupted at a desired temperature between 673-873 K. From these tests the weight loss of samples were determined and changes in the individual constituent of sulfide minerals were analyzed. For pentlandite-based Ni-concentrates the ignition temperature was 705-710 K (approximately 435 °C). Pyrite was the first sulfide to oxidize. Reactivity of the violarite-based concentrate was greater than those of the pentlandite-based concentrates. The stoi-chiometry of pentlandite changed before ignition because of preferential oxidation of iron. Rapid oxidation of the pentlandite mineral occurred at about 823 K (550 °C). By 900 K about 90 % of the iron in pentlandite was converted to hematite, and NiS containing some iron was formed.

Jan 1, 1994

By Eulogio Velasco, Jose Nino, Marcos Cardoso

"Recycling of aluminum scrap for production of secondary alloys used for automotive applications is increasing continuously. Automotive alloys require a strict control to remove alloy impurities, inclusions and excess of magnesium. The advantage of aluminum is its recyclability with large energy and emission savings with minimal loss in material properties. The aim of this work is to study the magnesium removal from recycled aluminum by chlorine injection in a reverberatory furnace, and removal by an oxidation process at high temperature in an industrial rotary furnace.The magnesium removal by gas injection is carried out by the reaction between chlorine and magnesium, with its efficiency associated to kinetic factors. In the rotary rapid oxidation of aluminum and magnesium elements at high temperature is characterized by the formation of surface films composed of magnesium oxide. Additionally this work reviews the benefits of an efficient demagging process.IntroductionThe advantages of using light alloys for automotive applications include fuel economy improvement, greenhouse gas reductions and polluting emissions. These characteristics makes the aluminum alloys an attractive option for automotive components such as powertrain products and other critical parts like cylinder heads and blocks. [1]Aluminum alloys coming from recycled automotive components, used beverage cans (UBC) and wrought alloys have positive effects in the energy savings and current environmental trends. Producing a scrap recycled aluminum ingot consumes approximately 5% of the energy required to produce a primary aluminum ingot from bauxite ore. [2]"

Jan 1, 2011

By C. Ek

In bismuth metallurgy, low-copper high-sodium mattes are by-produced. Different charges containing mixtures- of crude mattes, oxidized matte, and/or copper sulfide concentrate and/or copper silicate ore have been smelted to give a rich matte and a disposable slag, then converted to obtain blister copper with high recovery and a rich slag to be recycled.

Jan 1, 1983

By Ray Y. Lin

This study explores the formation of sodium pyrosulfate in molten sodium sulfate resulting from dissolution of SO3 at temperatures between 1160 and 1250 K. Solubility of SO3 in Na2SO4 melts at temperatures between 1160 and 1250 K under gas mixtures of SO2, O2 and argon was investigated applying a thermogravemetric analysis (TGA) technique. The activity of Na2O in the melt was determined with a high temperature electrochemical cell (ECC). Results showed that the SO3 solubility in molten Na2SO4 increases with decreasing temperatures and increasing SO3 partial pressures. Enthalpy of SO3 dissolution in molten Na2SO4 was calculated to be -119 kJ/mol for infinite dilute solutions. Thermochemistry of Na2SO4-Na2S2O7 melts was analyzed based on information obtained from both TGA and ECC techniques. Detailed examinations of the earlier low temperature measurements in the Na2SO4-Na2S2O7 system along with data from this study reveal that the solution behavior between Na2SO4 and Na2S2O7 can be satisfactorily treated as regular with the interaction parameter, , being 2.7 kJ/mol. The phase diagram and the field of SO3 partial pressure has been generated with the thermodynamic calculation using a regular solution approach.

Jan 1, 2006

By D. K. Panda

The behavior of single drops with gas evolution at the interface is of interest because this is one of the important reactions that occur in oxygen steelmaking vessels, where a large amount of iron-carbon drops are dispersed in an oxidizing slag. The carbon dissolved in these drops, reacts with the slag to form CO, which is evolved as a gaseous phase. A room- temperature model was used to study the nature of this type of reaction including the effect of various factors such as viscosity and the presence of surface active impurities. Experiments were done for reacting drops over a wide size range to observe various regimes of behavior. Large single drops were levitated in a counter current flow to produce a sufficiently long residence time to allow the study of the various stages in the reaction. The emphasis of this work was to obtain photographic evidence of a high quality to describe all possible modes of behavior, and so a lot of effort was given to developing and perfecting experimental techniques.

Jan 1, 1994

By Stephen Northey, Nawshad Haque, Terry Norgate

"Life cycle assessment (LCA) is a recognized tool to evaluate various processing routes for metal production. Declining ore grades and higher specific energy requirements for primary metal production put greater emphasis on recycling. Greenhouse gas (GHG) emissions of steel and aluminium metal production were quantified with recycling scenarios using material recovery facility (MRF) data from the database of SimaPro LCA software. The GHG footprint of the MRF is relatively minor compared with that of associated transport during collection (i.e. 10 times more than MRF) of curbside recyclable material. Additionally, if the bulk recyclable material is sent overseas (i.e. Australia to China) from the MRF for further processing, the GHG footprint of shipping can significantly be larger compared with the sum of the collection and MRF (assuming electricity is from same source). Thus opportunities exist for reducing GHG emissions from secondary metal production if it is processed close to the MRF.IntroductionIt is a challenge to recycle metals significantly, although theoretically infinite recycling is possible due to their elemental nature. Leaks from the metal stocks in society occur through corrosion, wear and dispersive uses, or via land filling or similar activities that return metals to the earth. In order to provide a technically sound and transparent assessment of metal recycling, a methodology such as life cycle assessment (LCA) should be used. By taking a life cycle perspective, the beneficial recycling properties of metals can be evaluated in a manner that enables appropriate comparisons with other materials or product systems that do not have recycling loops. In practice, mixtures of primary and secondary metals are often used in new products, and also at the end-of-life various processing methods are used for recycling.The difficulty of introducing recycling into LCA is to set the right boundaries for the different flows ending in different product systems. It is a question of which observed material flow belongs to the first product system and which one to the second or subsequent systems. Recycling can be part of any product LCA. However, it is often a complex issue which requires specific considerations. As pointed out by Yellishetty et al. and Birat et al. [l, 2], LCA practitioners are left with much freedom in allocation of environmental burdens to account for recycling, thus making subjective judgments on recycling and allocation of credits to recycling. This often makes it difficult to compare the results of LCA studies conducted by two different practitioners even on the same processes. As LCA is often used to define policy in government, business and society circles, it should be based on a sound, objective and unbiased description of recycling."

Jan 1, 2014

By Ivo André

Sorption of copper ions from aqueous solutions by dried biomass of the aquatic plant Potamogeton luscens was studied at laboratory scale. The aquatic plant was collected in water resources in Brazil, washed, dried at 60°C and ground in a bladed mixer. Sorption experiments were conducted in agitated flasks and in a packed bed column. Maximum copper removal was obtained between pH 5.0 and 6.6 when copper was present in the ionic form Cu'. Sorption followed the Langmuir isotherm with saturation attained at 35 mg/g. Free energy of sorption was found, to be of the order of -25 kJ/mol. Sorption kinetics data were better described by a second order reaction and rate constants were calculated in 0.030 1/(min.mg) for - 4.0 mm particles and 0.081 1/(min.mg) for - 0.59 mm particles. Removal of metal ions in a packed bed column showed that Potamogeton luscens biomass can be used in several sorption/dessorption cycles. After sorbent saturation, copper ions can be recovered from the loaded biomass by elution-with H2SO4, solution. Main mechanism responsible for heavy metal uptake was found to be ion exchange. Results are discussed in terms of the surface properties of the biomaterial, solution chemistry of copper ions and thermodynamics parameters.

Jan 1, 1995

By Vinod K. Sikka, René Cooper

"Cohoes, New York 12047 Intermetallics are an attractive class of advanced materials. The aluminide intermetallics offer advantages including: (1) lower density, (2) oxidation resistance, (3) carburization resistance, and (4) interesting mechanical properties because of their ordered crystal structure. Even though the attractive properties of the aluminides and other intermetallics have been known for nearly four decades, their practical applications have not been developed for two reasons: (1) the poor ductility (in some cases, both ambient and high temperatures) and (2) the lack of processability into meaningful components. Recent advances such as ductilization of Ni3Al by small additions of boron and the knowledge that environmental effects are the major cause of poor ductility in Fe3Al and FeAl systems have brought the intelmetallics into the forefront of research and their commercial applications. This paper has described a method for melting Ni3AI-based alloys that successfully utilize the exotherrn for the formation of NiAl from the elemental materials. The reaction-synthesis method has also been utilized for the production of NiAI and NiAI-based alloy powders from the elemental powders. The reaction-synthesized powders of NiAI and NiAI-based alloys were consolidated by hot extrusion and evaluated for tensile properties over a temperature range from room temperature to 1050ºC. The powder-processing conditions have been found to have more influence on the ductile-to-brittle transition temperature of NiAI than the powder-production method.IntroductionIntermetallics are an attractive class of advanced materials [1-11]. The alum in ide interrnetallics offer advantages including: (1) lower density, (2) oxidation resistance, (3) carburization resistance, and (4) interesting mechanical properties because of their ordered crystal structure. Even though the attractive properties of the aluminides and other interrnetallics have been known for nearly four decades, their practical applications have not been developed for two reasons: (I) the poor ductility (in some cases, both ambient and high temperatures) and (2) the lack of processability into meaningful components. Recent advances such as ductilization of Ni3Al by small additions of boron and the knowledge that environmental effects are the major cause of poor ductility in Fe3Al and FeAl systems have brought the intermetallics into the forefront of research and their commercial applications. The paper will briefly review the processing techniques being pursued for the commercial applications of Ni3Al-based intermetallics. The major emphasis of the paper will deal with synthesis of Ni3Al and NiAI intelmetallics."

Jan 1, 1994

By D. W. Lawler

Prior to the manufacture of sulphuric acid in metallurgical plants, the SO2 rich gas from the smelter, roaster, or furnace must be cleaned to removed particulates, volatile contaminants, SO3, and water. Cleaning is accomplished by contacting the. gas with cooled weak acid. The system is designed so that all the contaminants, originally in the gas are captured in the weak acid, which then becomes an effluent from the plant. Historically, the entire weak acid effluent stream has been treated for disposal, with no attempt to recycle or recover any part if it. This is becoming increasingly environmentally unacceptable, and operators must consider better methods of treatment and recovery. In this paper, Kvaerner Chemetics discuss a number of options that allow the contaminants to 'be separated from the acid' value. This will result in an acid byproduct that can be sold or used elsewhere, and will minimize the volume of hazardous byproducts that must be discharged.

Jan 1, 1998

By Grant E. Casley

Since 1970 Mount Isa fines Limited has made a significant increase in blister copper production from approximately 100,000 to 155,000 mt per annum and in fact 161,040 mt were produced in the calendar year 1974. Flowsheet developments including fluidised bed roasting and converter slag flotation are discussed, particularly their contributions to minimising major equipment changes in smelting and converting. The use of model- ling and simulation techniques for such an exercise is mentioned. The paper reports the alterations made to both equipment and operating techniques in the reverberatory furnace and converter sections to achieve the regular production of 250 mt of blister per converter day from a 41% Cu matte grade. The effects of flux composition on converting performance are highlighted. The air quality control programme is discussed in relation to its restriction of blister copper production.

Jan 1, 1976

By Rzyman Michal, Nakamura Takashi, Shibata Etsuro, Grabda Mariusz, Oleszek-Kudlak Sylwia

"Tetrabromobisphenol A (TBBPA) and many systems based on the synergistic effect of brominated organic compounds with Sb2O3 are extensively used as effective brominated flame retardants (BFRs) in many materials such as plastics and textiles. Thermal degradation of BFR containing plastics leads to the formation of hydrocarbons and gaseous compounds such as HBr and SbBr3. Our thermodynamic considerations indicate that these gases can act as bromination agents for metallic oxides such as ZnO, Cu2O, CuO, PbO and FeO. Moreover, these metallic oxides have the thermodynamic tendency to brominate easier than does Sb2O3. The aim of this study was to investigate experimentally the reactivity of ZnO with 1) HBr originating from the thermal decomposition of TBBPA and 2) SbBr3, which is formed during thermal degradation of brominated flame retardant plastics. The thermal treatments of the mixture of compounds of interest were investigated by thermogravimetry coupled with mass spectrometry.IntroductionTetrabromobisphenol A (TBBPA) and many systems based on the synergistic effect of brominated organic compounds with Sb2O3 are extensively used as effective brominated flame retardants (BFRs) in materials such as plastics and textiles. For instance, 4.5 million tons of flame retardant plastics containing BFRs are produced in Japan each year. Thus, in thermal treatments such as the incineration and melting of solid wastes, BFR containing plastics are intentionally or unintentionally included in the wastes. Thermal degradation of BFR-containing plastics leads to the formation of hydrocarbons and gaseous compounds such as HBr and SbBr3 [1-5]. Our thermodynamic considerations [6] indicate that heavy metal oxides such as ZnO, Cu2O, CuO, PbO and FeO should easily react with HBr prior to Sb2O3 and also with SbBr3, the main gaseous product in the thermal decomposition of TBBPA, forming low boiling point metallic bromides suitable for the volatile separation of heavy metals. The metal oxides are also expected to qualitatively and quantitatively affect debromination and decomposition of the flame retardant."

Jan 1, 2008

By I. C. Howard, E. J. Palmiere

"Heat transfer and friction in hot flat rolling have traditionally been characterised by an average heat transfer coefficient (h) and an average friction coefficient (p.). However, the presence of oxide scales and asperities at the interface question the use of such averages. The apparent irregularity and lack of pattern of interactions at the interface has prompted this present investigation to move away from averaged h and 11 values, and to study their local evolution based on probabilistic rules. The approach is based on the probability of finding the workpiece surface in a specific configuration at a particular instance of time in the roll gap. These rules are based on observations of surface phenomena such as scale behaviour during hot rolling. The model is implemented using user-subroutines integrated with the commercially available finite element program ABAQUS™. The results show the strong dependence of h and u on the local scale interactions. In particular, the effect of scale thickness, material behaviour and processing conditions on the evolution of hand 11 are discussed. Finally, the development of a Cellular Automata based Finite Element (CAFE) model is proposed to model the combined interfacial phenomenon of friction and heat transfer at the tool-work piece interface.IntroductionIntricate interactions between process variables in hot rolling of steels make it a challenge to the modelling community. For a given material and geometry combination, reducing interfacial power losses can increase the efficiency of the rolling process. The roll-strip interface, therefore, forms the critical zone and is currently the domain of intense investigation, especially to characterize interfacial frictionl • 2 and heat transfer3 • 4 . These interfacial phenomena are inter-related and cannot be studied in isolation. However, very few mathematical models4 • 5 combine an analysis of friction and heat transfer and deformation of the strip-roll interface taking into account the role of asperities and oxide scales."

Jan 1, 2001

By Bin Zhu, Mingmei Zhu, Hong Zhou, Xiaofei Dou, Bin Xie, Yu Wang, Tiancheng Lin

In this study, the formation of 2CaO·SiO2 and 3CaO·P2O5 solid solution (nC2S-C3P) in hot metal dephosphorization process is discussed. The variations of CaO and SiO2 mass, both in nC2S-C3P solid solution phase and liquid slag phase with increasing P2O5 mass in CaO-SiO2-FetO-P2O5 slags were calculated using Factsage software. CaO-SiO2-FeOt-P2O5 slag containing up to 18 % P2O5 was melted at 1823 K then cooled to 1673 K. The contents of CaO and SiO2 both in the solid solution phase and liquid slag phase of quenched samples were observed and analyzed by SEM/EDS. Both the calculated and experimental results show that the contents of CaO and SiO2 in the solid solution phase decreased, just opposite in the liquid slag phase, with increasing P2O5 content in the slags. Formation mechanism of nC2S-C3P solid solution in the slags was derived based on the ionic structure theory of molten slag. The SiO4 4- in the nC2S-C3P solid solution can be replaced by PO4 3- in the liquid phase resulting in the increasing of free Ca2+ and SiO4 4- in liquid phase.

Jan 1, 2015