Search Documents

By M. Huang

A conductivity-based sensor for on-line measurement of free acid was recently built. This sensor is suitable for high ionic strength solutions and its corrosion-free operation is based on induction currents. It has been tested against literature data and measurements made using a previous developed contact-type conductivity cell, with an average difference within 1%. The electrical conductivities of H2SO4?H2O, H2SO4?MgSO4?H2O and NaCl?Laterite-H2Osolutions at temperatures up to 250 °C were discussed. It was found that the solution conductivity depends on various factors, such as the electrolyte concentrations, the type of electrolytes, temperature and the amount of dispersions. A semi-empirical model was developed to account for all the factors discussed. This model was further tested on actual process solutions from the hydrometallurgy of nickel where sulphuric acid solutions containing a variety of metal sulphates and solids. The average difference between the estimated acid concentration from this model and the one from titration was generally less than 5%, which is excellent for industrial applications.

Jan 1, 2006

By M. Kawakami

In the blast furnace, the reduction of iron oxide and gasification of coke occur simultaneously. It is well accepted that the gasification reaction controls the simultaneous reaction. Therefore, it is important to develop highly reactive carbonaceous materials. It is also known that the reaction is accelerated catalytically with the addition of some materials. In the present work, the catalytic effect of iron, nickel and CaO on the gasification of graphite and coke was examined. The catalytic effect of iron, nickel and CaO on the reaction rate of graphite was noticed The effect was larger at lower temperature. At 1373 K, the effect almost vanished. The effect was larger in the order of CaO, iron and nickel. The reaction rate of de-ashed coke increased by the addition of iron and nickel. The effect of iron was larger than that of nickel. The effect was larger at higher temperature, which was contrary to the case of graphite. The reactive surface area increased also by the addition. Therefore, the catalytic effect on reaction rate might be attributable to the increase in the reactive surface area.

Jan 1, 2006

By Roberto Parra

The wear and corrosion phenomena in the furnace lining of the ferrous and non ferrous pyrometallurgical processes are complex problems where chemical, interfacial and mechanical phenomena are presents. The characteristics of the processes determine the conditions to which these materials are submitted, where the thermal conditions reached during the operation is one of the most important parameter. Assuming that all the degradation phenomena are thermal activated, the rate of the different steps of the wear mechanism will depend on the thermal field in the lining. In view to apply the independent physicochemical knowledge of degradation mechanisms to the analysis and design of furnace lining the methodology of the Nodal Wear Model (NWM) was done. It combines the mathematical modelling of the heat transfer in the lining with the physicochemical control equation for the wear-corrosion phenomena. The NWM has been applied to different examples: theoretical analysis, laboratory scale test and industrial applications. We present in this paper the theoretical background of the model and two examples of applications: the sole of an electric furnace and the earth of a blast furnace.

Jan 1, 2006

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006

By Roger Agnew

Sulphide ores mined by Inco Limited in the Sudbury District contain small quantities of cobalt. During beneficiation, cobalt distribution to various streams is similar to nickel. After smelting, nickel is selectively extracted by carbonyl refining and the cobalt remains in the carbonylation residue. This residue is processed in a specialized hydrometallurgical plant to produce precious metal residues, copper cathodes, and a nickel- cobalt carbonate intermediate product. The nickel-cobalt is shipped to Port Colborne where the cobalt is separated as cobaltic hydroxide and refined to metallic cobalt. This paper deals specifically with the recently constructed Electro Cobalt Refinery. The cobaltic hydroxide is dissolved and residual zinc, copper and nickel are removed by ion exchange and organics by a carbon column. The purified cobalt solution is fed to the electrowinning circuit where cobalt rounds are produced on stainless steel mandrels. In the design and construction of the refinery, special attention was directed to materials of construction both for the process equipment and the physical plant, operating control and flexibility, and the quality of the working environment. The end result is an efficient and clean operation which yields a product of excellent quality.

Jan 1, 1988

By Cameron Harris

With the consolidation of the copper industry in the second half of the 20th century resulting in fewer plants treating ever increasing quantities and qualities of feed, the enormous flexibility of the Noranda Process gives it significant advantages over many competing technologies for the production of matte. Toll smelting, recycling, and secondaries treatment will become the cornerstone of profitable operations for all but the lucky few who have large captive mines associated with the smelter. Consequently, the ability to respond to changing market conditions without significant metallurgical or operational upsets will be of considerable commercial advantage. The inherent stability of this bath-smelting process leads to tight matte grade control, while the bath turbulence leads to rapid consumption of feeds with widely varying physical characteristics. Low capital and operating costs combined with a layout suitable for retrofit into existing converter aisles makes it a sensible choice for parts of the world still experiencing the aforementioned consolidation, which is essentially complete in fully developed economies such as the United States of America and the European Union. This paper will discuss features of the Noranda process compared with other technologies and its place in the future global copper production industry, which is set to become increasingly competitive and aggressive.

Jan 1, 2002

By Jeffrey F. Adams

Gypsum fouling is a common problem in the hydrometallurgical industry. It is a particular problem in free sulphuric acid neutralization, or iron removal operations where sulphates are removed from aqueous solutions by the addition of calcium-containing bases. Previous work revealed a strong correlation between the degree of gypsum supersaturation in the reactor and the rate of scale growth indicating that scale formation and growth are primarily controlled by chemical phenomena. However, the chemical behaviour of gypsum is variable and unpredictable with solution chemistry and temperature. Many of the "rules of thumb" that are used to predict its behaviour (and avoid fouling) are in fact based on gypsum solubility in water, rather than on real mixed metal sulphate systems. However, despite this unconventional solubility behaviour, we have been able to accurately model it in Ni, Mg, and Zn containing solutions over a wide range of temperature (25°C-90°C) and solution concentration (0-6 m) using the OLI simulation software. Furthermore, by studying fouling rates in a simulated continuous neutralization reactor, the relationship between process conditions and fouling rates were explained for the first time. This has led to an understanding of how techniques for minimizing gypsum fouling work.

Jan 1, 2003

By Z. R. Llanos, W. G. Deering

Gulf Chemical and Metallurgical Corporation (GCMC) has been operating facility for treatment of spent catalysts in Freeport, Texas since 1974. Recently, GCMC expanded its operations with the addition of an electric furnace for the production of fused alumina and mixed alloys. GCMC and its affiliate Sadaci, started up a new pre-treatment facility in Ghent, Belgium in 1998. GCMC is also part owner of Bear Metallurgical Corporation, a major producer of ferroalloys in the United States. This paper reviews the processes at these facilities. Changes in the management of hydrotreating and hydrorefining spent catalysts are discussed in light of recently issued federal regulations that made the majority of spent catalysts a listed hazardous waste.

Jan 1, 2000

By R. R. Beebe

"Laboratory and pilot-scale tests are almost invariably required before metallurgical development can proceed. Difficulties with sampling, as well as with classical chemical and physical scaleups, are normally anticipated and relatively well-understood, but more subjective factors also come into play, including misunderstandings of the operating scheme chosen, wrong ""lessons"" learned from similar operations, failures to handle data appropriately, and even arbitrary intervention by management. The paper examines some of these subjective factors and suggests ways to guard against them. Several anecdotal case studies are used as examples, including when and where to heap leach or to mill specific types of gold ore.When the Romans first exploited the gold-rich gossans at Rio Tinto, they were guided by analyses and tests that delineated the ore deposits, identified the richer portions, and measured the gold recoveries achieved. There is little evidence, however, to suggest that test data were used to develop improved methods of metallurgical extraction. Indeed, it is likely that ores too difficult to treat were simply passed by, at least until improvements in full-scale operations could deal with them. For example, it is not difficult to imagine that an early metallurgist might test a tin ore by placing some in a fire; a smallscale emulation of the method actually used in practice."

Jan 1, 1997

By Oleg I. Platonov

The process for desulfurizing coke oven gas in a regenerative system ?scrubber-stripper?, with sour gas being fed to Sulfur Recovery Unit (SRU) and tail gas being recycled to raw coke gas scrubber, has been developed. A key problem of this process is the presence of elemental sulfur in the SRU off-gas, which may deposit on gas-blowing equipment, thus disrupting its operation. A new treatment technology for SRU off-gas that has been worked out for a Claus unit operated by «Russian Metallurgical Company» (RMC) in Magnitogorsk (Russia) is presented. It incorporates a catalytic hydrolysis/hydrogenation stage, where all sulfur-bearing species such as sulfur dioxide, carbonyl sulfide and elemental sulfur are converted to hydrogen sulfide. The SRU in Magnitogorsk comprises three main units: gas re-heater; catalytic hydrolysis reactor and waste gas cooler. Re-heater is required to increase temperature of the process gas up to a level of catalytic conversion (beyond 330-3500C). Oxygen utilized as an oxidizing agent reduces the volume of waste gas to a minimal possible value. The operational data garnered since 16.07.2004 clearly shows that the new technology allows high-level purification of Claus tail gas from elemental sulfur. Unlike SCOT ? process, this technology does not require separate stages for H2S removal and enrichment that tangibly simplifies its implementation at lower capital and operation expenditures.

Jan 1, 2006

By Dan A. Mackie

Cyanide leaching operations have taken a beating from the press and the public at large for its seemingly haphazard approach to control of cyanide solutions and containment of tailings. Major spills in Colorado, Guyana, Spain, and more recently, Romania, have highlighted what had already been perceived to be a bad scene. Citizen initiatives and legislative actions are increasing. Whether these indictments are justified or not will not be debated in this paper. What this paper presents is that the technology to avoid these disasters and future ones has been around for more than ten years but has been ignored by the industry, despite demonstrated' cost effectiveness. It is time for miners to wakeup, and use emerging, instead of old, technologies.

Jan 1, 1998

By P. G. Schirk, D. J. Roth

ALTEK has developed a processing system that can receive large pieces of dross & bath, of various metal contents, and reduce and separate these highly metallic concentrates into oxides and non-metallics. This system achieves these results without grinding the metallics into fines. Its unique feature results in the preservation of metallic unit in its largest possible size, which allows for maximum .metal recoveries. The Tumbler, an ALTEK-Didion International joint development, and the ALTEK High Velocity Impacting System (HVIS) are the key elements to this process. This paper will explore the advantage of this cold cleaning system over the direct melting of the raw dross in the reduction of landfill waste. The system also works well for removal of the aluminum from bath from primary smelters.

Jan 1, 2000

By Ryuhei Masuda, Kenji Oosumi, Yasuhiko Watanabe, Yutaka Nagakura, Tomoya Ohzono

"In order to promote recycling of aluminum scrap, it is required to remove inclusions that have a remarkable influence upon the product quality. An internal filtration technology using a new filter, which is made by coating an adhesive on the surface of the conventional filter, has been developed as a new removing technology for inclusions.The technology has made it possible to remove inclusions as small as 10-20µm in the molten metal, which have been impossible to be removed by the surface filtration technology using conventional filter, An inclusion removal rate of up to 90% has been attained.The technology will contribute not only to recycling of aluminum products but also to the improvement in the quality of current products."

Jan 1, 2000

By Kazuya Koyama

The leaching of copper from a printed circuit board (PCB) and the electrodeposition of copper from a cuprous solution in ammoniacal alkaline solutions were examined in order to develop an energy-saving hydrometallurgical process for copper recovery from electronic scrap. In the leaching experiments, copper in the PCB was oxidized by Cu(II), and Cu(I)-ammine complex ions were formed. The copper(I)-ammine complex slightly depressed the leaching rate, while Cu(II)?ammine markedly enhanced it. During the electrodeposition experiments, the current efficiency of copper deposition was approximately 100% in the current density range of 200 to 1000 Am-2. The electrodeposition of copper from the Cu(I)-ammine complex solution favored the production of plates rather than powders.

Jan 1, 2003

By R. D. Prengaman

Lead usage in paint, anti-knock gasoline additives, pipes, seals, and solder has declined markedly over the past 30 years. Products utilizing the unique properties of lead and its ability to be recycled have survived and grown. These products include shielding, glass (particularly TV and computer screens), sheet for roofing, stabilizers for PVC, insoluble anodes for metal production, electronic solders and lead acid batteries. With the loss of markets many companies have decreased lead product development efforts. Much of the patent lead materials development is devoted to lead acid batteries. In the past 25 years, the automobile battery has been almost doubled in power and reduced in weight, leading to a nearly three-fold increase in performance. Corrosion-resistant lead alloys and improved battery designs have made battery lead usage more efficient. The same corrosion-resistant battery alloys are utilized to increase the life of electrowinning anodes. The challenge for lead product development is not only to maintain and improve the existing lead products, but also to develop the growing lead acid battery market for telecommunications, uninterruptive power sources, remote area power, hybrid and electric vehicles. Lead

Jan 1, 2000

By Takayuki Ichikawa

Hydrogen storage properties of ballmilled mixtures composed of the hydrogenated nano-structured carbon (CnanoHx) and lithium hydride (LiH) were examined by thermal and optical spectroscopic analyses. LiH needs higher temperature than 600°C for hydrogen desorption even under vacuum condition, while CnanoHx, which was mechanochemically synthesized from graphite powder by ballmilling under hydrogen atmosphere, reveals hydrogen and hydrocarbons desorption in wide temperature range from 300 to 800°C. Nevertheless, the composite of CnanoHxand LiH prepared by ballmilling desorbs hydrogen in relatively lower temperature range from 150 to 450°C. These phenomena indicate that the thermally liberated hydrocarbon radicals immediately react with LiH and release hydrogen instead of hydrocarbons emission, because CnanoHx contains hydrocarbon groups at the edge of nano-meter sized graphenes, which are recognized as IR active C-H stretching mode, and LiH is well-known as an ionic crystal. Furthermore, it is of interest that a nanostructural feature persists in this composite even after annealing at 350°C, which shows excellent cycle properties as hydrogen storage media.

Jan 1, 2006

By Ashish Kumar

Comminution is an essential mineral processing operation to liberate the minerals from the ore. This however, is an energy intensive step in mineral processing industries. This work highlights the possibility of saving in grinding energy for ore comminution reducing work index of the ore by effective utilization of microwave energy. This reduced work index results in increased throughput of the grinding circuit in mineral beneficiation plant in order not to shift the product size. The fundamental principle behind this application remains the ability of microwave to heat individual phases within the ore matrix. The constituents of the ore typically having different thermal and mechanical properties develop stress of sufficient magnitude to create intergranular and transgranular fractures during heating and subsequent quenching of the ore. The experiments conducted with the ore samples of Zawar Mines and Rampura Agucha Mine of Hindustan Zinc Limited, India (A member of Vedanta Resources Plc) reflect a substantial up-shift in cumulative weight percentage passing in finer sieve fractions under quenched conditions. Further, the experiments carried out on Rampura Agucha ore reveal 20-30% reduction in work index, which result in decreased milling time or saving in grinding energy. The simulation studies estimates a 2-4% increase in plant throughput. Moreover, preliminary flotation studies indicated a significant increment in total metal recovery and concentrate grade for the desired grade and recovery values respectively. This paper is a technical note on the laboratory investigations carried out at Central Research & Development Laboratory of Hindustan Zinc Limited. Results have been encouraging to progress the work further. It is also proposed to carry out modeling work for simulation so as to predict the changes in minerals.

Jan 1, 2006

By Jannie S. J. van Deventer

Geopolymers are novel engineering materials with the potential to play a highly significant role in the transformation of the construction materials and building products industry in the push towards sustainable development. These materials are formed by activation of industrial aluminosilicate waste materials such as coal ash or blast furnace slag with alkaline solutions. Geopolymers derived from coal ash can exhibit superior mechanical properties and chemical stability when compared to ordinary Portland cement (OPC). The use of waste-based geopolymers can also result in significant (up to 90%) reduction in carbon dioxide emissions when used in cement replacement applications. In addition to the formation of conventional pre-cast products, these high performance mineral binders are ideally suited to use in the encapsulation of mine tailings, immobilization of heavy metals and back-filling of mines due to their chemical stability and resistance to acid attack. A key attribute of geopolymer technology is the robustness and versatility of the manufacturing process; it enables products to be tailor-made from a range of raw material sources (waste and/or virgin) with specific properties for a given application at a competitive cost. Despite these key technical and environmental attributes, it is the ability to add significant value to coal ash or and/ or metallurgical slag waste streams which drives the commercial development and uptake of the technology.

Jan 1, 2006

By Helena Byrdziak

KGHM Polska Miedz SA, in existence since nineteen seventies, operates three underground mines and three smelters with total production of over 400 000 mtpy of electrolytic copper. Its impact on the environment, very serious in the past, has been gradually reduced. While in general emissions into the air and water have been brought under control, attention recently has shifted to the disposal of wastes and residues. The main streams of wastes are flotation tailings, slags and dust captured from the dedusting systems. Much effort has already been expended and is still being spent to utilize this waste for by-products production or to dispose of it within the process by recycling. The most effective measures taken up thus far, as well as present activities directed at tailings disposal, are presented.

Jan 1, 1997

By James A. Warren

The phase field method has been successfully employed as both a tool to model heterogeneous materials and as numerical method for calculating the motion of interfaces and phase boundaries without explicitly tracking those interfaces. The method has been used to model a diverse suite of problems describing the microstructural evolution in materials. These models are derived from thermodynamic arguments and symmetry principles, and usually guarantee positive local entropy production for systems out of equilibrium. Descriptions of how phase field methods can be applied to the problems of solidification, grain growth, and electroplating will be presented.

Jan 1, 2001