Search Documents

By K. B. McTaggart, G. Owusu, P. J. Merrin

"This study was conducted at Hudson Bay Mining and Smelting's zinc electrowinning tankhouse to determine the effects of varying levels of antimony and continuous gelatin addition on current efficiency. The levels of antimony and gelatin were varied from 0.012 to 0.030 mg/l and 0 to 10 mg/ll2 • 31 respectively, based on neutral ZnS04 electrolyte. A non-linear mathematical model relating current efficiency with antimony and gelatin was produced. The optimum operating point for gelatin was 6.5 mg/l. On the other hand the current efficiency increased with decreasing antimony levels. An interaction term between gelatin and antimony is present but is not significant enough to improve the ability of the tankhouse to handle purification upsets in antimony. Individually, the current efficiency was linear (decreasing) with antimony, and parabolic with gelatin concentration. However, at low antimony concentrations stripping of the cathode sheet was difficult. IntroductionThe zinc electrowinning tankhouse at Hudson Bay Mining and Smelting was designed in the 1930's and consists of 120 rows with each row containing ten cells. This system cascades acid from cell to cell In a row, with neutral zinc sulphate solution added to each cell through manually controlled spigots. Animal glue additions are made manually three times per day by operations personnel. The problem with this type of cell design and operation is that feed solution flows and composition can vary from cell to cell and from row to row due to the large number of manual control points. A new system which reduces the number of manual control points was designed and tested to determine if improvement in control of cell conditions would affect current efficiency. This system mixes spent acid, neutral ZnS04 electrolyte and reagents (gelatin, antimony and strontium carbonate) in a separate mix tank, ensuring that all cells receive a uniform feed solution. Gelatin was used in the test system instead of animal glue (which is presently used) because of the poor solubility and supply of industrial animal glue. The study reported here is the first in a series of experiments designed to justify the need to modify the present cascading cell feed system (Figure 1) to the proposed feed system (figure 2)."

Jan 1, 1997

By Aïda Espinola

This work is part of a research program concerning the study of heavy metal removal and selective recovery from electroplating waste waters in the Guanabara Bay ecosystem, preventing the potential noxious retarded effect of landfill, specially in a country of heavy rainfall. A flow-throw cell was employed to adapt to the limits established by the local legislation for disposal in rivers and seas. The cell design is presented and preliminary results show that this cell may be applicable for the decontamination from copper.

Jan 1, 1994

By Milance Mitovski, Milorad Cirkovic, Vlastimir Trujic, Dragana Živkovic

"In this article, it is analysed the possibilitis and the effects utility waste energy of process sulfuric acid production in the existing technical-technological conditions. The utility second process energy, reduction the fuels consumption, reduction environment pollution and its effects are shown, too. High heat quantity is produced as the result of exothermal reactions in the production process of sulfuric acid in Bor. A part of this heat is sufficient for the process development, and significant part of this heat presents low-temperature heat energy that is irretrievable lost. Investigations were carried out based on production of 485 t of monohydrate/day of sulfuric acid. By recovery of this heat quantity for heating purposes, about 20.000 – 25.000 t of coal/year would be saved, what would significantly improve the power efficiency of the smelter copper production. IntroductionTechnological process of copper production in RTB BOR (Serbia) produces a significant quantities of high temperature secondary (waste) heat energy that is uncontrolled “lost” in the vicinity. Secondary heat energy is produced in pyrometallurgical copper production in quantity of 1,621 kWth/kg of dry concentrate or existing heat (that presents a difference of heat at furnace outlet and heat at temperature over temperature of dew point of sulphuric acid gases) in quantity of 1,315 kWth/kg of dry concentrate. For designed capacity of Copper Smelter in Bor, the existing heat power of secondary energy is 92,111 MWt, what is an equivalent to the power of steam-turbo plant where the Rankine-Clausius heating cycle is done, and that is 28,334 MWe."

Jan 1, 2008

By P. R. Seidl, R. C. C. Ribeiro, J. C. G. Correia

"More than 95% of asphalt pavement materials consist of aggregates. The highway and construction industries consume a huge amount of aggregates annually causing considerable energy and environmental losses. The aggregates are usually produced from neighborhood aggregate quarries or form natural aggregate sources. The use of marble and granite wastes from quarries as aggregates might help meet the increasing demands and slow down any detrimental effects on the environment. Chemical and physical results showed that the use of marble and granite wastes from quarries in the asphalt production is quite fusible. Consequently, granite sawmills would perform a clean technology. This technology would also have an economical impact by not spending on basalt extraction.IntroductionThe granite fines generated from sawmills of ornamental rocks comes as a great problem and it lacks undeletable solutions. This problem involves the preservation of the environmental and constitutes one of the subjects more critical the point of view of social beneficiation of the population. The Cachoeiro de Itapemirim County, Espírito Santo State, Brazil is an example, of this problem. In this area, the granite and marble fines generation is around 15.000 ton/year.The problems generated by these residues affect with more emphasis the animals, such as the cattle, which inhaled the water content fines of granite and this residue accumulate in their lungs. Other great problem observed is the sanded of the river and the reduction of aquatic life.This problem is beginning to be set out due to performance of Center of Mineral Technology (CETEM), and of several other organisms of Rio de Janeiro State, aiding the sawmills owner’s. This help consists of teaching the best procedure of discard the residues and studies for its use, for instance the production of mortars, tiles, bricks and road pavements [1]."

Jan 1, 2008

By Srinath Viswanathan, Zhijing Zhang, Ramana G. Reddy

"The viscosity measurements were carried out on melts of 380 aluminum alloy containing 20 volume % SiC particulates under various shear rates at different temperatures using a Brookfield viscometer. Results showed that viscosities of the melts increased with decreasing temperature and decreased with increasing shear rate. These results were compared with those of 356 alloy and it was found that the temperature had a more significant effect on viscosity of 356 alloy than that of 380 alloy containing SiC particulates. Based on the present experimental data an empirical viscosity model, which considers the effects of both solid fractions in the melt and shear rate, is proposed.IntroductionDiscontinuously reinforced metal matrix composites materials (MMCs) such as aluminum alloy containing SiC particulates have considerable potential for applications in the automotive industry because of their superior stiffness, higher specific mechanical properties, better dimensional stability and strength retention at elevated temperatures when compared to their monolithic counterparts. They have a great advantage in the specificity of their properties, meaning that specific materials can be engineered for specific applications. With such freedom of design, materials engineers have to accumulate a very large database of mechanical properties. Among these properties, the viscosity of alloy slurries is very important for producing, casting and forming process of metal matrix composites materials because viscosity has a decisive influence on fluid flow. The understanding of the rheological behavior of alloy slurries is necessary for these materials to become economic reality. Therefore, a study was carried out to measure the viscosities of 380 aluminum alloy containing 20 volume % SiC particulates under various shear rates and temperatures. In addition, a viscosity model representing the primary features of the alloy slurries was developed."

Jan 1, 1999

"Silver is traditionally recovered in base metal smelters (lead and copper), or as a by-product of other precious metals (gold and/or PGM's). This paper presents the results of non-conventional techniques to recover silver from complex materials. The PLATSOL® process has been developed to recover, in one step and without the use of cyanide, base metals (copper, cobalt, nickel) and precious metals (gold, PGM's) from sulphide concentrates too low in grade to enter the mainstream extraction processes. Silver is only partially recovered in solution with gold and the PGM's during the PLATSOL® process. However, the silver minerals are transformed into silver chloride, which can then be recovered from the PLATSOL® residue using conventional techniques. Some South American silver concentrates contain levels of impurity (mostly arsenic) so elevated that the penalties incurred significantly affect the process economics. The present results have shown that a low temperature calcination process transforms the concentrate into a product well suited for traditional recovery treatments. Metallurgical details will be provided, as well as the results of mineralogical studies that helped clarify the process mechanisms.IntroductionSilver occurrences in nature are very diversified, and, therefore, primary silver is produced as a by-product of many base metal and precious metal operations [1], as well as a co-product of most gold ores. However, difficulties can arise when high temperature processes are used for refractory gold ores or copper concentrates, or when the silver concentrate contains impurity elements such as arsenic that trigger high penalties."

Jan 1, 2012

By Daniel Kim, Ari Rantala

Efficient on-line monitoring of electrolytic cell performance in copper electro-refining has been challenging due to the need for complex electrical measurement systems and the management of the enormous volume of data. Based on Kennecott Utah Copper's innovation Outotec has developed a novel and innovative electrolytic cell monitoring system called CellSense™ System. As the system is based on self-powering from bus bars, wireless communication, on-line adaptive modeling and easy to access information and alarming, traditional obstacles of electrolytic cell monitoring are eliminated. With cell voltage and electrolyte temperature measurements, CellSense System enables real-time cell performance discovery and early reaction to critical production or quality disturbances such as short-circuiting, flow blockages, cold cathodes or electrolyte temperature excursions. During the past few years the system has been delivered to over 3500 commercial cells. In this paper the largest CellSense™ System ever delivered and recently adapted by Kennecott Utah Copper with 1412 cells monitored on-line for high tankhouse performance, cathode quality and optimized operator work flow is presented. Early results and benefits are discussed.

Jan 1, 2012

By Bo Yan, Jiaquan Zhang, Haibo Sun

"Based on the validation of steady-state isothermal mathematical model by a 0.4-scale water model for the single-strand slab casting tundish, the effect of varying pouring temperature on the flow, temperature field, and residence time distribution(RTD) of the liquid steel was studied by a transient hydrodynamic model. Due to the decreasing temperature of ladle stream over a casting period of 50 min, the direction of vortex flow at the downstream side of dam changes to clockwise from the anticlockwise at 4 min after the new teeming, and reverts to anticlockwise direction again at 43 min. Meanwhile, the melt flow state in the dam hole is also varying with time. For conventional isothermal water modeling, the RTD parameters obtained are much different as compared with the non-isothermal ones. For the flow control devices(FCD) design, however, the identical optimal scheme can be concluded from the point of view of isothermal modeling.IntroductionOriginally, tundish was adopted as a buffer and distributor to hold and allocate molten steel for sequence casting upon ladle exchange and to provide a desired steel flow rate to the mould below. With the increasing demand to strand quality, the tundish has become a critical metallurgical reactor to enhance inclusions removal, avoid reoxidation of molten steel, and prevent slag entrapment. The general trends to obtain these metallurgical effects are to optimize steel flow pattern and to extend the residence time of molten steel in the tundish through increasing the volume of tundish and/or using FCDs in the interior of the tundish."

Jan 1, 2012

By E. Almendras de Siegel

Pyrometallurgical processes have the thermodynamic capability of treating complex and dirty ores and concentrates to produce high purity metals and inert slags. Modem pyrometallurgical processes are environmentally sound and competitive with other processes. However, there is still a need for sensors and other practical tools that permit a rapid evaluation of the performance of these processes. In order to contribute to satisfying this fundamental requirement, the authors developed the IDENT.LA software that permits the automatic mineralogical analyses of inorganic materials, including the final and intermediate products of pyrometallurgical processes. The technique allows determining the grain size distribution of mineralized inclusions, the surface relations between metallic phases, and conducting modal analyses of the essential phases that are present in the samples. Three basic automatic operations are performed: creating a representative image of the sample; identifying the metallic and non-metallic phases; and measuring the features of the resulting image. The results are used to evaluate the performance of pyrometallurgical and other processes. In this paper, the authors discuss the application of the technique to a sample of slag from a slag cleaning process that uses a carbonaceous reductant. In this case, process performance impacts not only on the efficient reduction of the slag magnetite and on copper recovery but also on the quality of the process off-gas. The mineralogical analysis of the slag is a valuable tool in assessing process performance and in recommending changes of operating conditions.

Jan 1, 1999

By T. W. Gonzales

The BHP San Manuel Smelter operates an Outokumpu Oy flash furnace, conventional Peirce-Smith converters, anode casting facilities, and two double contact sulfuric acid plants. The flash furnace was commissioned in July 1988 and since then, the smelting capacity has been continuously increased to 30% above design. The converter operation was challenged to process larger amounts of matte with existing capacity. Utilization of industrial technological improvements and people technology transformed the Converter Department from a constraint to easily accommodate the new demonstrated flash furnace capacity. This technology also increased secondary consumption, converter campaign life, and reduced operating costs. This paper will describe the important Converter Department achievements in the past five years.

Jan 1, 1999

By Shiwei Sun, Hongxu Li, Xiangxin Hao, Xie Yang

"Environmental impact assessment of copper metallurgical processes will soon become a compulsory activity in the future. The goal of this work is to analyses the copper metallurgical processes including pyro-metallurgy and hydrometallurgy based on the life cycle assessment method implemented in GaBi software. The evaluation indicators such as global warming potential (GWP), acidification potential (AP), photochemical ozone creation potential (POCP) and human toxic potential (HTP) are taken into account. The results show that the major environmental impact phase in pyro-metallurgy derives from beneficiation because of the largest material and energy consumption. It is also shown that copper hydrometallurgy has significantly lower environmental impact than pyro-metallurgy. Based on the evaluation results, some corresponding optimization methods are recommended to reduce environmental impact.IntroductionCopper is an important metal in modem society due to its wide variety of uses, including electrical wiring, heat exchangers, piping and roof construction and increasingly consumer electronics. Demand for copper has increased dramatically over the past decades, driving production rates almost exponentially. Annual production of copper was estimated to be 20 million tonnes in 2012 with Chinese production at about 6.06 million ton in 2012P1. The production process of copper has environment impacts that often go unnoticed by the producer. Higher production, coupled with declining ore grades, is placing increasing pressure on the natural environment.Sound environmental management helps producers improve their manufacturing technique. LCA is a well-established tool for assessing environmental impact potential and can be readily adapted to map impact potential over time, which can be used to quantify the environment impacts of a product or a process [21. This is achieved by creating an inventory of all the energy and material flows used in the process's life cycle. The results of an LCA can be used to improve the operation of a process so that they have less impact on the environment."

Jan 1, 2014

By Moo Eob Choi

A new process for converting sulfur dioxide to elemental sulfur by a cyclic process involving calcium sulfide and calcium sulfate without generating secondary pollutants was developed at the University of Utah. In this process, sulfur dioxide is reacted with calcium sulfide to produce elemental sulfur and calcium sulfate. The latter is reduced by hydrogen to regenerate calcium sulfide. In the present work, the effects of different pelletization conditions for the initial reactant calcium sulfate on the strength and reactivity of the pellets were determined. These conditions include the type, amount, and impregnation method of catalyst, binder amount, and sintering. Experiments were also performed to determine the effects of temperature in the range of 973-1173 K, pellet size, cycle repetition, and water vapor or carbon dioxide content in sulfur dioxide stream on the reaction rates of the cyclic process. Nickel-catalyzed fired pellets produced by the use of molasses or cement as a binder showed good reactivity as well as high compressive strength during the cyclic tests. The binder amount did not significantly affect the reaction rate.

Jan 1, 2006

By Kalyani Das Sarkar

"Steel Authority of India Limited, a Public Sector Undertaking with a production capacity of 14 million tones of crude steel, is India's largest steel maker and ranks among the leading steel producers in the world. SAIL owns and operates eight manufacturing plant – five integrated steel plants at Bhilai, Durgapur, Rourkela, Bokaro and Burnpur producing carbon steel, and three speciality steel plants. All integrated steel plants have hospitals of 650 – 750 bed capacity with modern facilities to serve it's employees and adjoining localities in a clean and sustainable environment.According to the Bio-Medical Waste(Management and Handling) Rules, 1998 and as amended to date, all Bio-Medical waste which is generated during the diagnosis, treatment or immunization of human beings or in research activities pertaining thereto or in the production or testing of biologicals are to be categorized and taken to any facility wherein treatment, disposal of this waste or processes incidental to such treatment or disposal is carried out.The hospital management has created adequate treatment facility for Sharp and Infectious Waste, Pathological Waste and Anatomical Waste through Autoclave, Shredding Machine and developing deep burial pits. Some of these hospitals is ISO 9000-14000 certified. Use of above said treatment facilities in these hospitals are discussed in this paper.INTRODUCTIONBio-Medical waste means any waste, which is generated during diagnosis, treatment or immunization of human beings or animals or in research activities pertaining to these or in the production or testing of biologicals.Steel Authority of India Limited, a Public Sector Undertaking with a production capacity of 14 million tones of crude steel, is India's largest steel maker and ranks among the leading steel producers in the world. SAIL owns and operates eight manufacturing plant – five integrated steel plants at Bhilai, Durgapur, Rourkela, Bokaro and Burnpur producing carbon steel, and three speciality steel plants. All integrated steel plants have hospitals of 650 – 750 bed capacity with modern facilities to serve it's employees and adjoining localities in a clean and sustainable environment."

Jan 1, 2008

By Yong Hack Lee

Nonferrous smelting processes have been through a rapid transformation since the beginning of 1980. The copper smelting technology has changed from the conventional Blast Furnace process to the Flash Smelting and MIB process. In the field of lead smelting, the technology has changed from the Blast Furnace Smelting to the Direct Smelting such as QSL and KIVCET. In 1992, Onsan Refinery successfully commissioned Direct Smelting QSL technology for lead. The QSL could produce more than 160,000 ton per year of lead bullion from lead concentrate and various residues. Moreover, since the year 2000, the TSL (Top Submerged Lance) Technology utilizing the same Direct Smelting process has been successfully commissioned to treat lead concentrate as well as lead sulfate residue produced from a hydrometallurgical zinc plant. This paper presents and compares the energy flows of lead smelting processes such as a conventional process and the Direct Smelting Processes plotted on the Pb-O-S phase diagram. The oxygen potential diagram suggests how to control the oxygen potential in the furnace. Also, it describes the recent operational experience in the TSL plant of Onsan Refinery with necessary mass balance of key elements.

Jan 1, 2003

By Michel G. Drouet

Dross, a major by-product of all processes involving molten aluminum, forms at the surface of the molten metal as the latter reacts with the furnace atmosphere. It generally represents 1 to 5 wt% of the melt, depending on the process, and contains on average about 50% free aluminum dispersed in an oxide layer. Since aluminum production is highly energy-intensive, dross recycling is very attractive from both the energy and the economic standpoints. The conventional recycling process using salt rotary furnaces is thermally inefficient and environmentally non-acceptable because of the production of salt slags. Hydro-Quebec has developed and patented a new salt-free technology using a rotary furnace heated by an electric arc between two graphite electrodes, called DROSCAR®. A 600-kW pilot plant in operation at LTEE is in use to demonstrate the process. This process provides aluminum recovery rates over 90%, using a highly energy efficient, environmentally sound production method. In 1994, 400 tonnes of aluminum dross were treated in this facility and several tests on various types of dross have also been conducted in early 1995. A report on the results will be presented.

Jan 1, 1995

By Milorad Cirkovic, Mile Bugarin, Vlastimir Trujic

"Industrial scale testing was performed in the plant-site of Bor Company. Charging sample was from 4-5 tons for each particular test. All operations in industrial scale investigations were carried out in one furnace. For the aim of successful realization of experiments, and primarily for safety and prevention the risk of toxic contamination the working environment, a plant was designed and constructed for cooling and wet dedusting of gases formed during smelting process, zinc removal and flame refinement of molten metal. For the requirements of industrial investigations a complete plant for cooling and wet dedusting of gases has been constructed for brass scrap processing. In this plant, the original ultra-sonic water spraying devices have been installed. The efficiency of such simplified system for gas treatment has been 98,6%. Introduction Permanent development of techniques and technology causes formation the considerable quantities of secondary raw materials that are much more relevant as the raw material base for many metals. Due to a fact that large quantities of metal, are concentrated in the waste materials, large consideration is given to this topic, and numerous technologies for this waste recycling are developed in the world nowadays. High energz price and permanent increase of metal price on the world market have made that secondary raw material tretament, for the aim of various metals production, becomes more and more relevant in the world. In comparison of metal production using enrichment and metallurgical treatment of primary raw materials, the non-ferrous metals production from secondary raw materials has a range of advantages, as well as: - Low level of capital investments, - High technological recovery of qualitative secondary raw materils, - Considerably low consumption of energetic resources regarding to the treatment of primary raw materials (ore and concentrate), - Reduced consumption of unrecoverable mineral resources, - Reduced enviroment pollution [1,6]."

Jan 1, 2008

By A. M. Alfantazi, M. Boissoneault, D. B. Dreisinger, J. Synnott

Acid mist generation is a major concern in zinc, copper and nickel electrowinning industries and there is a strong environmental drive to control its emission into the work environment. Foaming reagents are typically added to the electrolyte to alleviate this problem. In zinc electrowinning, Licorice and Saponin are examples of foaming reagents used for this purpose. In order for the foaming reagent to be effective, its foaming behavior must be determined. In this work, a test procedure was developed to study the foaming characteristics of various surfactants for use as foaming agents to control acid mist in aqueous metal electrowinning. This new test was termed as "mini-flotation test" and it was used to study the foaming behavior of a large number of reagents in an industrial zinc sulfate electrolyte under simulated zinc electrowinning conditions (gas sparging). In addition, the influence of important process parameters such as current density, electrolyte temperature, reagent addition level and sulfuric acid concentration on the foaming characteristics of the electrolyte for each surfactant were investigated. The results of this study have identified the most important factors that influence foam formation, growth and stability. This method could be used as a process control for reagent addition in the cellhouse by generating a calibration curve for the optimum electrolyte conditions.

Jan 1, 1997

By D. N. Collins

A sampling program was conducted in which both spoon and isokinetic sampling techniques were used to collect samples from the reaction shaft. The samples were then characterised by chemical, XRD and mineralogical analysis. Further information was acquired by measuring the oxygen potential and temperature at the bottom of the shaft using disposable probes. Comparison of the results of the two sampling methods showed that the spoon samples were devoid of material less than 25 m. Sulfur analyses on the samples provided information on the extent of reaction, plume shape and recirculation patterns. Disposable probe measurements showed the measurable particle temperatures ranged from 1150 to 1700 °C and that the material falling into the bath had a normalised oxygen potential similar to the slag. These latter measurements combined with the sulphur elimination and mineralogical analyses provided further information on the extent of reaction and enabled the reaction sequence to be ascertained.

Jan 1, 1999

By P. Regan

Following the introduction of the Contilanod process over 10 years ago at Copper Range and IMI Refiners, significant changes and advances have been made to this pioneering anode production technique. A new radial flow metal feeding concept has been developed that allows a substantial increase in casting rates on the Hazelett® twin-belt caster. To cut the 45 mm thick continuous anode plate into shaped anodes at rates of 100 t/h or more, a filly moving hydraulic shear designed by Mannesmann Demag has replaced the slower speed plasma cutting torch. Details of the.new caster and shear are presented along with operating results from the new lines starting up in 1999 at the Gresik smelter/refinery in Indonesia and the completely revitalized Mansfelder Kupfer und Messing complex in Germany.

Jan 1, 1999

By D. P. Cook, M. I. Bloch, J. A. Dantzig

"In this article, we describe a combined experimental and computational program to study the filling of automotive wheels during low pressure die casting. Experiments are performed by placing thermocouples into the mold walls of a production caster for the Ford F 113 wheel to measure the temperature profiles in the die during processing, and to infer the filling pattern. Computational models are also developed using a 36° section of the wheel pattern, taken directly from CAD data files. We use these models to simulate the filling and heat transfer processes. Comparison between experimental and computational results are presented, demonstrating the viability of this procedure.IntroductionAutomotive companies are using increasing amounts of aluminum in production vehicles: While the main driving force is improved fuel economy through weight reduction, replacing steel wheels by aluminum also offers the potential for improved vehicle performance by reducing unsprung mass. For these reasons, many new vehicles are now supplied with cast aluminum alloy wheels, and the aftermarket for these wheels continues to grow.The most common production process for these wheels is low pressure die casting. The process is subject to numerous defects, including microporosity, cold shuts, cold folds, misruns and inclusions. Scrap rates at the caster of the order of 10% are not uncommon. Many wheels also have large production runs, into the hundreds of thousands of wheels per year. Thus, the cost savings from even small reductions in scrap rate have the potential to be quite significant.Most of the defects are associated with the filling and solidification processes in the mold. The molds are air cooled, and the placement and sizing of cooling passages is currently as much art as science. The ultimate goal of this project is to improve that situation, by implementing simulation procedures that enable engineering design methods to be used in die and process specification."

Jan 1, 2000