Search Documents

By Wentao Guo, Xuefeng She, Qingguo Xue, Jingsong Wang

By the coke gasified reaction device and online measurement high-temperature compressive strength apparatus, the variation of pore structures of coke after gasified reaction with CO2 and H2O was investigated. Research illuminating the influences of solution loss rate, temperature, and carbon species on compressive strength of coke was also carried out. The results showed that the total compressive strength was higher than for the reaction with CO2. The high-temperature compressive strength of coke decreased with the increasing of solution loss ratio or temperature after reacting with CO2 and H2O. At the same solution loss ratio, the damage of pore structure to coke strength after gasified reaction with H2O was relatively smaller and the deformation resistance was stronger when compared with that in CO2.

Jan 1, 2016

By Nils Eivind Kamfjord, Halvard Tveit, Ingeborg Solheim

"Because of its negative environmental effect the attention towards NO emissions increases. This again leads to new demands from the authorities for better surveillance and control of emissions. Earlier and recent industrial measurements towards FeSi- and Si-metal furnaces reveal quite high NO-emission. The NO is believed to be produced in the combustion zone above the furnace surface, mainly as thermal NO.In order to expand the knowledge on NO-formation in silicon metal production, a pilot scale experiment in a 440 kVA silicon furnace has been carried out. The experimental set-up was designed with a view to be able to copy and manipulate the formation mechanisms for NO by controlling the flow of false air into the off-gas system.The resulting NO-values corresponding to the different air inlet to the furnace top, show significantly differences between the different air inlet geometries.IntroductionNOx is the common notion for the two gases nitric oxide (NO) and nitrogen dioxide (NO2). Since combustion of fuels, such as gasoline, diesel, bio diesel, propane, coal, and ethanol, forms NOx the dominating contributors to NOx emissions are the on-/offshore transportation industry and power generation based on fossil fuels [1]."

Jan 1, 2012

By V. Gornitz

The Orphan mine uranium deposit, Grand Canyon, Arizona, is a cylindrical collapse-breccia pipe, 70 to 150 m in diameter and 500 m deep. Pipe fill was derived from the Supai Group, Hermit Shale, and the Coconino Sandstone. Uraninite, with Cu, Fe, Pb, Zn and Ni-Co sulfides is concentrated along the pipe boundary ring fracture (annular ring) and within the central porous sandstone matrix. There is some suggestion of vertical and lateral zonation of U with respect to Cu. Reduction of ferric oxide cement from red beds and recrystallization of carbonate, with formation of kaolinite preceded major ore deposition. Early Ni sulfides, arsenides and disseminated pyrite were followed by massive pyrite, and botryoidal uraninite, which in turn was suc-ceeded by Cu, Zn and Pb sulfides. A second, later generation of uraninite was closely intergrown with hematite and base metal sulfides. Oxidation of primary minerals may have been associated with Tertiary regional uplift. The paragenetic sequence closely resembles that of other Grand Canyon breccia pipes, except for the extensive development of the distinctive uraninite-hematite association. Mineral assemblages at the Orphan suggest possible mixing of the metal-bearing solution(s) with a more oxidized fluid, containing soluble uranyl complexes. Homogenization temperatures of fluid inclusions in calcite (GO-lIO?C) at the Orphan fall within the lower end of the range observed at other breccia pipes.

Jan 1, 1987

By Xingye Guo, Yeon-Gil Jung, James Knapp, Zhe Lu, Jing Zhang, Li Li

La2Zr2O7 is a promising thermal barrier coating material due to its low thermal conductivity and superior high temperature stability. In this work, Bilayer La2Zr2O7 and conventional 8 wt% yttria stabilized zirconia (8YSZ) coatings were deposited using plasma spray technique. Both singlelayer La2Zr2O7 and double-layer 8YSZ/La2Zr2O7 coating architectures were designed. Thermal cycling and thermal shock tests were used to evaluate coatings’ thermomechanical properties. All La2Zr2O7 coats were delaminated in the furnace cycle test in less than 20 cycles. This is because residual thermal stresses accumulated during thermal cycling. In the jet engine thermal shock (JETS) tests, the SCL La2Zr2O7 and DCL dense 8YSZ/La2Zr2O7 coatings were fully delaminated. In contrast, the DCL porous 8YSZ/La2Zr2O7 coating sample only partially delaminated on the edge. This is because of the porous 8YSZ layer provides strain compliance. The findings will help to propose efficient thermal barrier coating systems.

Jan 1, 2016

By Patrick M. Eduafo, Brajendra Mishra, Mark L. Strauss

Direct acid leaching of rare earth metals (REMs) from waste lamp phosphors is non-selective, leading to co-dissolution of impurities mainly calcium, phosphorus, silicon, iron and zinc. Calcining the phosphor powder at different temperatures followed by leaching with HCl isn’t efficient for the extraction of all the chief rare earths especially cerium (Ce), lanthanum (La) and terbium (Tb). Therefore, multi-stage leaching operations are required for the separation of the REMs in phosphor dust. This paper will outline a new process for extracting Ce, La, Tb, Eu and Y from waste fluorescent lamps using a three-stage leaching and separation process. A flowsheet has been developed which shows this process is selective and efficient.

Jan 1, 2015

By Jackson Jenkins

The second survey of world copper SXEW plants has been completed. Solvent extraction and electrowinning data published in 1996 has been updated and leach data from seventeen plants is now included. The following pages list the results of the thirty- two plants that responded to the survey. Selected information is summarized in graphical form.

Jan 1, 1999

By A. J. Schindler, F-P Sawyer, T. Logan, M. L. Shutey-McCann, R. M. Perry

"Test work on biooxidation pretreatment of low-grade refractory gold ores has been ongoing at Newmont Gold Company since 1988, including laboratory testing and pilot biooxidation heaps (360 to 23,000 tonne). Metallurgical results of the biooxidation process utilizing Thiobacillus ferrooxidans (T. ferrooxiddans) have culminated in the design, construction, and operation of a biooxidation demonstration facility. The facility has processed 708,000 tonnes of refractory ore, using a batched process with separate pads for biooxidation and ammonium thiosulfate gold extraction. Siliceous sulfidic refractory (SSR) and carbonaceous sulfidic refractory (CSR) ores are treated separately during biooxidation pretreatment unit operation. Following biooxidation, the ores are neutralization with lime and placed on oxide leach pads or stacked on the ammonium thiosulfate leach pad. Gold is leached with either cyanide for SSR ores or ammonium thiosulfate for preg-robbing CSR ores.This paper will only address the biooxidation pretreatment process of the SSR and CSR ores.AcknowledgmentsThe authors appreciate the cooperation and approval of Newmont Gold Company Carlin Operations management for its support and permission to publish this paper. The paper draws on efforts and assistance of the following people and several others which are to many to list who participated over the past five years in bringing this project to its fruition: Dr. James A. Brierley, Chief Microbiologist, Newmont Metallurgical Services; Dr. Rong-Yu Wan, Metallurgical Manager, Newmont Metallurgical Services."

Jan 1, 1997

By John L. Watson

Many metals-based industrial processes experience limitations in their operations due to an inability to effectively separate solids and liquids where partidesizes are less than 25 microns. Steel plant sludges ,generated, from the cleaning of furnace off-gases represent a typical example of processing difficulties attributable to material characteristics, and recycling or even efficient disposal of these materials is often a major problem. The use of a magnetic field to augment the traditional mechanisms of vacuum dewatering has, been demonstrated in previous work to have significant value in separating solids and 'liquids, where the solids exhibit some magnetic character. Magnetic vacuum dewatering has been used with magnetite ores and with blast furnace sludges and magnetic fields have been incorporated successfully in drum and disk vacuum filters. The research described in this paper investigates the use of magnetic seed material and flocculants to extend the application of magnetic, vacuum filtration to non-magnetic pulps. It is shown that the addition of a flocculant can enhance the capacity of drum and disk magnetic fIlters when treating materials, such as steelmaking sludges, which are only partially magnetic. In addition, the use of seed magnetite with a flocculant is shown to improve the dewatering of fine hematite pulps in a drum magnetic filter. However the use of a flocculant and seed magnetite had only limited success in improving filtration in a disk magnetic filter with a fine quartz pulp. A disadvantage of magnetic vacuum filtration with seeding appears to bean increase in cake moisture due to water entrapment in the floes resulting from agglomeration and magnetic attraction.

Jan 1, 1999

By Hao Deng, Hongmin Zhu, Jichao Li, Kai Huang

"Silicon and silicon carbide mixing micropowders obtained from the saw cutting industry of polycrystalline silicon ingot is separated by a simple sequential sedimentation. The Zeta potentials of the powders in the aqueous suspension are adjusted by varying the pHs with dilute acid or alkaline reagents. The dispersion and aggregation content of the microparticles is significantly influenced by pHs, and so their settlement velocity in the same hydraulic conditions are quite different, and silicon powders tend to suspend in the upper section of the suspension for its finer size and smaller density under the stronger Zeta potential repulsion force. The original content of the cutting powders with 30%wt silicon are separated into the Si-rich and SiC-rich powder respectively, and 62%wt Si-rich powder can be obtained after 4 times of sedimentation under pH = 8.0, showing the great potential for Si and SiC powder separation and recovery in a cost-effective way.IntroductionWith the fast development of photovoltaic (PV) technology these years, the market demand for the solar-grade high pure silicon material significantly increased, making the silicon recycling and recovery from the wire sawing slurry profitable and attractive[1]. Waste silicon slurry was produced in the multi-wire sawing process of a silicon ingot by using an ethylene glycol-based solution and silicon carbide abrasives as the slicing system. During this slicing process, about 30% of the silicon ingot will become the waste as the fine particles suspended in the slurry, which mainly consists of silicon kerf-loss particles, SiC fragmental particles, tiny iron fragments from the worn sawing wire and ethylene glycol-based solution [2]. The separation of above individual component is usually easy except for Si and SiC fine particles for their quite similar properties. So the biggest challenge for the effective recovery and recycling of silicon particles from the wire sawing slurry actually lies in the mutual separation of silicon and silicon carbide particles."

Jan 1, 2012

By Alex Probst

With low metal prices and increasing value placed on plant water and tailings disposal areas, it is becoming essential to maximize the efficiency of solid-liquid separation processes. Since its inception over 25 years ago, the use of flocculants has grown exponentially. While flocculants play a crucial role in the sedimentation process, they are also a major operating cost. Recent innovations are revolutionizing the industry once again. New thickener designs are doubling thickener-loading rates while reducing flocculant consumption. The feedwell, as the heart of the thickener, is undergoing many significant metamorphoses. With CFD and other advanced computational analysis, feedwell technology is being examined more thoroughly than ever before, The result is that the thickener previously thought of, as a "Black Box" is now being mapped and controlled with state-of-the-art technology. This paper will examine recent design improvements in all aspects of thickeners in order to project the look of the thickener of tomorrow.

Jan 1, 1999

By Yuan Lu, Yiming Rong, Richard D. Sisson Jr

With the development of quench technology, there is a trend of using gas quench to replace liquid quench for less distortion and residual stress. The fundamental difference between the liquid and gas quench is the heat transfer coefficient, not only the values but also the shape of the curve as a function of temperature. The equivalent heat transfer coefficient for the liquid and gas quench is analyzed by simulations and experiments. Even it may result in the same hardness in the liquid and gas quench, the steel microstructure may be different because of the different cooling processes, and therefore other steel properties, such as toughness, may be different. The cooling process, microstructures and properties such as hardness and toughness should be examined when designing the liquid or gas quench processes.

Jan 1, 2015

By Chai Liyuan

This paper focused on the preparation of porous ceramic pellets for microorganism carriers. A new method for the process was developed using simple gel-casting and bubble-in-water-in-oil type of multiphase double emulsion. The globules, consisting of a foamed sepiolite slurry suspension, were dispersed and consolidated in spherical shape in liquid paraffin as gelation progressed. The green pellets were sintered at 1100°C. The influence of surfactants, extension ratio and impeller revolution rate on the process and characteristics of the pellets was investigated. The pellet size was in the range of 1~4mm and determined directly by impeller revolution rate. The fine cell diameter of porous ceramic was in the range of 100~500m and the micropore diameter was less than 5m. The inner macropores were interconnected and extend to the external surface. It is impossible to analyze a result by SEM micrographs and digital camera.

Jan 1, 2006

By Khosrow Nikkhah

Increasingly ion exchange systems are being included in design of hydrometallurgical plants for metal extraction or impurity removal. Because such systems operate sequentially and are based on resins that exchange one ion for another, store it temporarily and release it to a regenerating solution, the usual steady state heat and mass balancing tools and spreadsheets cannot be used to design them successfully. This paper outlines the role of dynamic simulation in design of ion exchange systems. Examples are given for use of dynamic simulation in design and investigation of equipment based on consideration of the effect of input criteria such as expected ion loading and elution profiles. The methodology for dynamic modeling using IDEAS in design of multi column ion exchange trains operating in parallel is presented. Results shown include the non-steady state distribution of extracted metal and limitations imposed on operating conditions. These conditions include proposed sequencing of columns for loading and elution cycles, loading, elution and recycle flow rates as well as size and choice of related ion exchange plant equipment.

Jan 1, 2003

By Ben Q. Li

An efficient numerical algorithm for solving steady state heat transfer and solidification problems is described. The algorithm is of boundary integral type and is based on the formulation of the field variables along the boundary of the domain of interest. Compared with the familiar domain-based methods, such as the finite element and finite difference (or finite volume) methods, this boundary-based method has an advantage of solving fewer unknowns and hence has a potential for reducing computational time significantly. Another and yet more important advantage of the present algorithm is that it is a stable scheme and is not prone to numerical oscillations resulting from convective effects, as often encountered in the domain-based methods. Therefore, no numerical or artificial diffusion (such as streamline upwinding) is necessary. Numerical examples are presented that are drawn from processing systems for producing aluminum-based materials.

Jan 1, 1994

By Reimers. Jan H.

Practically all the world's lead is produced by sintering and blast furnace smelting, or the Imperial Smelting Process which is a variant of the blast furnace process. Increased coke and labour costs and strict lead emission limits have, however, made blast furnace smelting undesirable in most countries. A change-over to other lead smelting processes providing better working conditions and lower emissions is, therefore,. expected to occur once economic conditions improve and the necessary capital expenditures can be justified. The need for new lead smelting processes has long been evident and a number of new processes have been proposed 'and advanced to various stages of development. One of the new processes is already proven on commercial scale, while several others are still being tested on pilot plant scale.

Jan 1, 1983

By C. Lupi

Electric arc furnace dust generated during the production of steels is regarded as hazardous waste because of the presence of leachable elements such as Cr, Pb, Cd .... Different processes are available according to the management policy chosen by the steelmaker: disposal. recycle and/or recovery. The feasibility of an hydrometallurgical Zn recovery process on fumes generated during the pyrometallurgical treatment of EAF dust has been investigated. The recovery of metallic iron, chromium and nickel as molten metal provides fumes very rich in zinc oxide ( 63.1% ) and poor in zinc ferrite. This secondary dust is still an hazardous waste and represents the raw material for the recovery of Zn and Pb. The waste material is first leached in 1.5 M sulphuric acid at 30°C to provide a Zn, Fe and Mn rich aqueous solution and a Pb and Ca sulphate rich sludge. The iron is eliminated by precipitation because is harmful to the following electrowinning process. The ftltered and purified leached solution is acidified in order to obtain good electrowinning conditions. A pure cathodic deposit of zinc is then produced in an electrolytic cell at laboratory scale.

Jan 1, 1996

By Kikuo Okuyama, I. Wuled Lenggoro, Manabu Shimada

"Aerosol processing of materials such as (i) gas-to-particle conversion process (e.g., Chemical Vapor Deposition (CVD) method) and (ii) liquid (or droplet)-to-particle conversion process (e.g., spray pyrolysis) has become of major interest to produce novel submicron- or nanometer-sized particulate material used in electronic and chemical industries. After reviewing recent theoretical and experimental researches on the evaluation of properties and morphology of fine particles by the CVD and spray pyrolysis methods, the importance of the process engineering approach· for aerosol processing of materials and the use of advanced aerosol measurement technology have been pointed out.IntroductionMaterial synthesis via aerosol processing offers a route to producing nanometer-sized and submicrometer-sized particles of high purity with specifically tailored chemical and physical properties. Especially, single nanometer-sized particles (nanoparticle materials) are considered to play an important role in the synthesis of nanostructured materials as well as in nanotechnology in 21st century due to their quantum effect and so on.However, the transformation of gaseous or liquid precursors to the final functional particulate matters consists of various complex chemical and physical processes. In order to control the size distribution and morphology of produced particles, it is important to analyze and model various phenomena, such as gas-phase or liquid-phase chemical reaction, nucleation, condensation, agglomeration and sintering that occur simultaneously in aerosol material processing. By introducing the Aerosol Science and Materials Science, the authors have been trying to model the changes in particle properties and morphology by gas-to-particle conversion and droplet-to-particle conversion processes. The authors have also been trying to obtain the experimental data on the particles properties as accurate as possible."

Jan 1, 2000

By Olga A. Gomon, Alexey N. Lozhko

The technology of heat treatment for metal frequently includes multiple fast heating and cooling of the products surface. If the product is heavy-weight or long-size, its moving from a zone of cooling to a zone of heating and return require a long time. Other important condition of ensuring qualitative surface at heat treatment is intensification of cooling phase. It is known that turbulization of a flow activates heat exchange and increases efficacy of cooling without increasing volume flow rate of water. Additional difficulty is to ensure the regularity of heating and cooling on length of a product. The technology of cyclic heat treatment of rolling products, at which mobile zone of turbulent heat exchange is formed on the surface of a product, was developed and realized. The submission of water occurs through to face spray systems. Each of the systems has six long-range atomizers, which are located circularly. Two flows of water move towards one another along a surface of a product. When they collide, the right zone of turbulent heat exchange creates heat transfer in this zone of 10-15 time more intensive than on other surface of a product. The effect of moving turbulent zone on length of a product is reached by changing the proportion of volume flow rate of water, which is created by face sprays. The speed of movement for turbulent zone along a surface of a product is chosen so, that the cooling takes place on a small depth only. Then after passing the turbulent zone over a determined site of a surface, its temperature recovers fast owing to hot internal layers. The parameters of process were determined by mathematical simulation of cooling in an installation. The equations for dynamics of movement of collision point of flows, which were received this way, are interesting supplementary products of research. The experiments show that frequency of movement of turbulent zone is an important technological parameter. It defines mechanical properties of a surface and should be chosen depending on a profile of product and metal grade. The results of comparison of mechanical properties of a surface of various rolling products, which were received by developed and conventional technologies, are described in this report. Dependence of regularity of mechanical properties on frequency of movement of turbulent zone is adduced.

Jan 1, 1998

By R. D. Pehlke

The history and present status of continuous casting of steel are reviewed, including a genera 1 description of current processes. Plant layout, process development and elements of machine component design are outlined, and key steps in integration into a stee-1 production system are detailed. Recent productivity advances and improvements in quality are described. Process developments are reviewed, and some future avenues for this technology are considered.

Jan 1, 1985

By Jyri Talja, Shaolong Chen, Hannu Mansikkaviita

"For optimum smelting results, proper treatment of the feed is needed to ensure favourable conditions for ignition characteristics, heat balance, mass balance with tolerable impurity levels, and overall process economics. Feed preparation consists of physical treatments before drying (blending), chemical treatments before drying, (roasting, if required), drying itself and physical treatments after drying (fractioning, if required).Effects of fluctuation on mineralogy and moisture should be minimized by blending the concentrates in a bedding plant prior to drying. As an alternative to drying, additional treatments such as roasting for impurity removal may be needed for part of the concentrate.Sustainability, energy efficiency, utilization of waste energy, low gas and dust emissions, product quality, availability and occupational exposure reduction are decisive criteria in drying today. These criteria are best met by the Kumera steam dryer, which has the best energy efficiency, zero CO2 emission, lowest operational and maintenance expenses, and superior availability and product quality.IntroductionFeed preparation plays a crucial role in having a smooth smelting operation and also the overall smelting economics in metal production. Therefore, it is of significant importance for all copper, nickel and lead smelter operations in which sulphide concentrates are fed to the primary smelting furnace. Generally speaking, the higher the metal content in the matte after primary smelting, the more important the feed preparation. This is of particular importance in the direct blister (DB) process for copper production and direct oxygen nickel (DON) for nickel production.Bedding is the first stage in feed preparation. This is very important for the sake of smoothing the mineralogical fluctuation in the feed for better smelting control. Its importance increases as the number of concentrates available for the feed mix decreases."

Jan 1, 2012