Search Documents

By Shubin Wang

Copper(II) and nickel(II) are often recovered from ammoniacal alkaline solutions by solvent extraction using hydroxyoxime extractants: both copper(II) and nickel(II) are extracted from ammoniacal alkaline solutions and, from the loaded organic phase, nickel(II) is selectively stripped with a dilute acid followed by copper(II) stripping with an acid of higher concentration. Since a small portion of ammonia is co-extracted with copper and nickel, the extracted ammonia should be scrubbed using a dilute acid before metal stripping. In the present study, a mechanistic model has been developed in order to support design and control of this process. The equilibrium distribution ratios of copper(II), nickel(II), and ammonia at 298 K using LIX® 84-I (active component, 2-hydroxy-5-nonylacetophenone oxime) as the extractant are successfully correlated by considering the relevant equilibria. Based on these results, quantitative prediction of equilibrium distribution ratios in the process has been made possible, and suitable conditions for the efficient separation of copper(II) and nickel(II) are discussed.

By Thomas F. Hagelien, Stein Tore Johansen, Svend Graadahl

"The dross appearing at the surface of an aluminium melt consists, in addition to aluminium, of mainly oxide films but also other non metallic inclusions. The inclusion particles are often poorly wetted by the metal and accumulate at the metal surface. However, in impeller stirred reactors for melt refining stirring may be exceedingly strong and inclusions accumulated at the metal surface may be entrained into the bulk metal. Concerning inclusion removal, such effects may deteriorate the effectiveness of melt refining.In this paper we investigate the surface entrainment of buoyant particles in a water model of an impeller stirred refining reactor. Under varying operating conditions the particle concentration in the bulk liquid is measured by laser light attenuation. The observed entrainment of particles is explained theoretically and metallurgical consequences of the findings are discussed.IntroductionIn the modern cast house continuos metal refining and casting is well established. One of the most distinct advances in metal refining has been the introduction of degassers which introduce bubbles into the metal. The bubbles act to remove dissolved elements together with nonmetallic inclusions. In the most efficient degassers stirring by different kind of rotors is applied to increase mass transfer and inclusion removal. However, it has been known from experience in the cast house that for violent stirring the concentration of some types of inclusions may increase from inlet to outlet of the reactor. This phenomenon has so far been attributed to production of dross in the reactor due to oxidation of metal. Due to removal of inclusions by bubbles the dross layer inside the reactor must be expected to increase in thickness by time. The removed inclusions and produced oxides due to strong stirring is removed at regular interval by the operators of the degasser. However, a fundamental understanding of the phenomena which take place in and below the dross layer is lacking. In the present work we add buoyant particles to the surface of a refining reactor and investigate how these particles may be entrained and dispersed into the liquid depending on the flow conditions. Similar investigations for gas stirred ladles have been performed by Taniguchi et al [1] who found that below a critical gas flow rate all particles are trapped at the surface. Above the critical gas flowrate the surface velocity are sufficiently high to entrain the particles. In this situation it looks like all particles are ready for the melt and a balance between terminal velocity and turbulent dispersion determine the concentration in the liquid."

Jan 1, 1999

By Michael A. Eamon

Magma Copper Company has operated its San Manuel SX-EW Plant facilities since 1986. The original plant facilities have a design capacity of 25,000 tons per year of electrowon copper cathode produced by processing pregnant leach solutions from an open pit/heap leach operation. In 1988, the plant was expanded to 50,000 tons per year to incorporate processing leach solutions from an insitu leaching operation. This paper presents a general overview of plant practices with particular emphasis on process innovations developed and implemented by Magma during construction and operation.

Jan 1, 1991

By Travis Knight

Mixed uranium and refractory metal carbide systems have been proposed for space nuclear power and propulsion applications. Solid-core space nuclear reactors could be utilized for low- earth-orbit (LEO) to geosynchronous-earth-orbit (GEO) transfers, manned missions to the moon or mars, and orbiter missions to the outer planets. However, these high performance space nuclear reactors present some challenging materials engineering requirements for operating in a high temperature, high radiation, and hot hydrogen environment. Since the RoverNERVA programs were concluded in 1973, significant advances in ultrahigh temperature materials technology have been made which can be applied to the development of an advanced solid-core nuclear fuel. Nuclear thermal propulsion (NTP) was first studied in the U.S. beginning in the mid-1950's during the RoverNERVA programs. During that time, about 20 rocket reactors were built and tested. More recently, Russian nuclear rocket reactor tests with pseudo-ternary carbide nuclear fuels (U, Zr, Nb)C and (U, Zr, Ta)C have been operated at temperatures as high as 3300 K for one hour. This study examined the processing parameters for fabricating the pseudo-ternary carbide, (U, Zr, Nb)C.

Jan 1, 1999

By K. J. Murphy, A. R. Smith, A. P. Odorski

"The need for large quantities of oxygen for use in metallurgical processes was a major driving force in the commercialization of tonnage air separation plants. Oxygen, nitrogen and argon impact the quality, energy efficiency and environmental aspects of metals production. Cryogenic air separation processes have been used to supply most industrial requirements, however, newer technologies are available or under development to meet the needs of today's and tomorrow's metallurgical processes. This paper reviews the technical features and state of development of adsorption, chemical, cryogenic and membrane technologies. The technologies are compared in terms of plant size, oxygen purity and pressure, nitrogen and argon co-production, product use pattern and back-up requirements. Computer control systems are described that optimize operation over varying load patterns and ambient conditions; substantially lowering energy consumption. IntroductionOxygen production totalled 390 billion cubic feet in 1987. Although current production is lower than the peak of 455 billion cubic feet reached in 1979, oxygen remains the fifth leading chemical product manufactured in the u.s. (1) Metals manufacturing and fabrication accounts for sixty percent of the oxygen consumed in the u.s. Oxygen use in the steel industry consists of air enrichment for conversion of iron ore, purification of the iron in basic oxygen or other furnaces, and for cutting and welding the finished steel product. Nonferrous ores are smelted in oxygen enriched atmospheres to reduce energy consumption and increase capture of sulfur compounds to meet environmental requirements. In the future oxygen usage is expected to become even more important in metals production as energy costs increase, environmental standards become more stringent, and as new coal based processes become commercialized. Oxygen usage per ton of metal in the new direct reduction processes can be up to ten times higher than traditional steel making."

Jan 1, 1988

By Larry M. Southwick

Pneumatic converting (Bessemerizing) of iron revolutionized the steel industry. Bessemerizing of copper (conversion of copper sulfide matte to copper metal) was proposed at almost the same time, but it was slow in being accepted. The differences between iron and copper converting were great and technical problems were substantial. It took 25 years for the process to become viable and another 25 years before a truly economical solution was found. A major economical and productivity problem was the short life for converter refractory linings. The first converters had acid (silica) linings, which were quickly consumed since silica was a flux for the process. Converters had to be relined at least once per day, a laboriously expensive manual process with only the most rudimentary mechanical aids available to assist. The industry was revolutionized almost overnight when finally a viable basic (magnesite) lining was developed. This lasted 100's of days versus less than one, leading to converters that were easier to operate and which handled larger charges. This change occurred after W.H. Peirce and E.A.C. Smith, with support from the Guggenheim interests, successfully operated a basic lined converter in a copper refinery in Baltimore. While Peirce and Smith are generally given credit for the development and explosive acceptance of this idea, a Pittsburgh industrialist, Ralph M. Baggaley, working in an independent smelter in Butte, Montana, successfully built and operated a basic lined converter four years before they did. In fact, the early support for Peirce and Smith likely occurred because Guggenheim's staff were encouraged after thoroughly examining Baggaley on his earlier successes. The questions of technology primacy between Baggaley and Peirce/Smith are ironically similar to those between Wm. Kelly and Bessemer in converting iron to steel. This paper will review what Baggaley (and other early researchers) accomplished, examine why he (or they) did not receive credit equal to Peirce and Smith and explore what his (their) place should be in the development of successful basic linings. More suspects than a Victorian Whodunit.

Jan 1, 1999

By C. A. Natalie

Prediction of average residence times for different particle size intervals during sulfide roasting was investigated. Calculations were done to predict average residence times using a model which employs empirical correlations for elutriation constants. Experimental average residence times were determined using a continuous., six inch diameter,. fluid bed roaster and compared with calculated residence time values. Comparison of calculated and experimental data showed that geometry effects may have .been significant when attempting to apply elutriation data to this roaster.

Jan 1, 1985

By C. J. McKee

A gold-silver-lead-zinc deposit at Montana Tunnels, Jefferson County, Montana is located in a diatreme of middle Eocene age (45 to 50 m.y.). Sulfide minerals within the diatreme occur as disseminations, veinlets, and locally as breccia matrix. Principal sulfide minerals are pyrite, sphalerite, and galena. The diatreme is a matrix-rich quartz latitic breccia with a fine grained rather soft matrix and heterolithic clasts. The ore deposit contains approximately 50 million tons of ore at a grade of 0.025 oz/ton Au, 0.5 oz/ton Ag, 0.25 % Pb, and 0.65 % Zn. Mining is by open pit methods. The original process flowsheet included flotation and cyanide leaching. Problems with the leaching circuit led to a change to the straight flotation process which is presently in use. To maintain a reason-ably uniform feed material, blending of ore is required for grades of four metals as well as for ore hardness and oxidation.

Jan 1, 1988

By O. G. Rivera, R. D. Moser, P. G. Allison, W. R. Whittington, P. Rivera-Soto, Z. McClelland, D. Francis

This research examined the evolving microstructure of quasi-static and dynamically loaded fully annealed metastable 301 austenitic stainless steel (SS). Experiments were performed to an interrupted strain value of 20% and to failure using a tension Kolsky bar (1000/s) and an electromechanical load frame (0.001/s). Electron Backscatter Diffraction (EBSD) identified the microstructural evolution from the as-received condition to the 20% strain level for the high and low rate interrupted samples. This material achieved over 60% elongation to failure with increasing strength as strain rate increased, as expected. Fractography analysis using SEM showed particles in the microstructure and a ductile failure mode. The 301 SS exhibited a greater amount of phase transformation from parent austenite to -martensite at the dynamic strain rate when compared to the quasi-static strain rate during the interrupted experiments. This result is indicative of the increased propensity for austenite to -martensite phase transformations at the high strain rate.

Jan 1, 2016

By Jewel A. G. Gomes

Lead has long been an USEPA priority pollutant and an important environmental and health concern because of its toxicity at ppb levels. In light of health and exposure data for lead, the EPA has set standards for Maximum Contaminant Level (MCL) and a MCL Goal (MCLG) as 15 ppb and 0 ppb, respectively. An accurate and rapid measurement of lead in the field remains a technical challenge. In this work, a relatively new method of deploying a nanoband electrode system using anodic stripping voltammetry has been optimized by changing deposition potential, electrolyte, and plating time used for the measurement of Pb(II) in water samples. Green rust has been proven to be an efficient intermediate matrix for removal of lead contaminants. We also report here the removal efficiency of lead using green rust produced by electrocoagulation, both directly and indirectly. Lead containing floc was also characterized through XRD, SEM, and EDAX techniques.

Jan 1, 2008

Direct electrowinning is an electrochemical process which has been developed for the extractive recovery of copper from dilute, acidic leach solutions. In passing through a thin particulate coke cathode. copper is reduced and electrodeposited in a thin layer forming a solid copper-coke sheet. The product is melted in a furnace to separate the coke, then the molten copper is fire refined to produce a salable product. A description is given of a prototype unit which is designed to treat 20 gpm leach liquor and recover over 100 pounds of copper per day. Economic analyses show that in a commercial facility producing about 25.000 TPY copper.*the direct electrowinning process has lower overall cost than either conventional iron-cementation or the newer liquid ion exchange-electrowinning when the leach liquors contain less than 2 grams per liter of copper.

Jan 1, 1976

By Cui Wang, Qian Li, Kexin Jiao, Haibin Zuo, Jianliang Zhang

Abstract：A rational cooling water system is the assurance for long campaign life of blast furnace．In the paper, the heat transfer of different furnace period and different furnace condition based on the water quality characteristics were analysed, and the reason of the heat flux over the normal from the hydrodynamics was analysed. The results showed that, the vapour-film and scale existence significantly influenced the hearth heat transfer, which accelerated the brick lining erosion. The water dynamic characteristics of the parallel inner pipe or among the pipes were the main reason for the abnormal heat flux and film boiling. As to the reasonable cooling water flow, the gas film and the scale should be controlled and the energy saving should be considered.

Jan 1, 2015

By H. Y. Sohn, Haitao Wang, Moo Eob Choi

"A novel ironmaking technology is under development at the University of Utah. This technology produces iron directly from iron ore concentrate by gas-solid suspension reduction. Hydrogen is the main reducing agent for high reactivity and for the elimination of carbon dioxide release in this ironmaking process. The direct use of concentrates allows bypassing the problematic pelletization/sintering and cokemaking steps in the steel industry.Intrinsic kinetics of the suspension reduction of magnetite concentrate particles by hydrogen has been measured. Experiments were carried out in the temperature range of 1423-1673 K, other experimental variable being hydrogen partial pressure, the amount of excess hydrogen and particle size. Under most experimental conditions, 95% reduction was attained within several seconds, which presents sufficiently rapid kinetics for a suspension reduction process. The reaction kinetics followed the nucleation-and-growth equation, and a rate equation that contains all the effects of the experimental parameters has been obtained.IntroductionWith the rapid increase in steel production, it is critical to control CO2 emissions which is the main greenhouse gas. It is inevitable to release a huge amount of CO2 when coke and/or coal are used as the main reducing agent in producing iron. As one of the methods to reduce the CO2 emission from ironmaking, the utilization of the gaseous reducing agents and fuels, including hydrogen, has been investigated [1-6]. The use of such gases forms the basis for a new ironmaking technology under development for producing iron directly from fine concentrates by a gas-solid suspension technology. This technology would reduce energy consumption by about 40% of the amount required by the blast furnace and drastically lower environmental pollution, especially CO2 emission, from the steel industry [4]. This is accomplished by adopting H2-based reductant and bypassing pelletization/sintering and cokemaking steps. Unlike other gas-based alternative ironmaking processes using shaft furnaces or fluidized-bed reactors, the suspension reduction technology is a high-intensity process because it will not suffer from the problems that other processes do when operated at high temperatures mainly from the sticking and fusion of particles."

Jan 1, 2011

By D. J. Wang

Based on the thermodynamic arid kinectic aspects, the vaccum distillation processes for the separation and recovery of metals from wastes are analyzed. As to the separation criteria, The separation coefficient and equilibrium composition relation between vapor phase and liquid phase are the bases of recovery of metals by vacuum distillation, The vaporization rates and condensation mechanisms are also discussed. Some experimental results which deal with metals-containing wastes are described and the performances of a new kind of horizontal vacuum furnace are introduced, which demonstrate that , vacuum distillation may be a prospective technique for circulation and regeneration of some non-ferrous metals from industrial wastes.

Jan 1, 1996

By Eugene Jak

Copper sulphide processing technologies face increasing pressures associated with decreasing concentrate grade leading to increasing thermal inefficiency and lower productivity. Impurity concentrations are on average increasing, creating potential environmental risk and additional treatment costs. In copper flash smelters dust, partially oxidised materials and fume formed from the condensation of volatile impurities, are routinely recycled to the feed. In the converting stage the heat balance is maintained by charging anode reverts and other inert materials. In both cases, the thermal energy available from sulphide oxidation is not fully utilised or optimised. The productivities of both smelter and converter stages can be potentially increased through the addition of a high copper, low iron, low impurity precipitated copper product. Calculations are carried out for fayalite smelter and calcium ferrite converter slags using an optimised FactSage thermodynamic database. The potential for significant increases in smelter and converter productivities using existing technologies are predicted.

By Takashi Yoshida

"This paper will discuss the recent situation and future of the zinc industry from the technical point of view. It includes recent problems faced by the zinc industry and technological developments. One of the biggest problems of the zinc industry is raw materials. Traditional zinc concentrate becomes much complicated with respect to its chemical and physical properties. Thus, each process faced various problems. Also, secondary resources, generating so called recycling processes, become much more important. Recycling is, of course, a very important aspect for sustainable development of society. Secondary raw material also includes a great variety of impurities not included or very low levels in traditional zinc concentrate. Some problems are caused by these impurities. To overcome these problems some technological challenges have been taking place. Details will be discussed in the symposium.IntroductionZinc is a very useful metal based on its elechtro-chemical, chemical and physical properties. The most important usage is galvernizing of steel which is used for automobile, construction and a very wide range of other indutries. Also, zinc is used for dicasting and other alloys such as brass. Smelting of zinc is different from other metal because of its electro-chemical properties. Many parameters should be controled compared with other metals such as iron and copper. Typical zinc smelting processes are the Imperial Smelting Process (ISP) and the electlolytic process. The ISP process is a pyro-metallurgical process using a blast furnace. The electrolytic process is a hydrometallurgical process. Both processes are energy intensive, and the smelting process cost is increasing because of higher energy costs. The situation of the ISP is very severe because of higher coke prices. Recently, many ISP plants have been shut down because of economic reasons"

Jan 1, 2012

By Xiao-hui Fan, Xu-ling Chen, Xiao-xian Huang, Gui-ming Yang

Grate-kiln-cooler is a predominant process of producing iron ore pellets in China. Since this process is of multi-variant, strong coupling and large hysteresis characteristics, a reliable performance monitoring is thus essential to ensure product quality and economic benefits. Aiming to efficiently monitor the pellet induration within this process, this study proposed an approach that combines statistical analysis and quality soft-measurement. Soft-measurement of pellet quality was accomplished based on the predicted time-temperature profile, and the soft-measured indices were on-line monitored using statistical control charts. Based on the proposed approach, a monitoring system for grate-kiln-cooler thermal process was developed for a domestic pelletizing plant. Running results demonstrate that our system can assist in the detection or diagnosis of abnormal thermal state and finally helps to stabilize the pellet production.

Jan 1, 2016

By John L. Sundstrom

Complete systems were designed -and are in operation to recycle the effluent streams and to remove impurities from tankhouse. electrolyte, Heavy em¬phasis was placed on making usable products from as many streams as poss¬ible at minimum capital and operating costs. Almost complete recycling: and reuse of water and sulfuric acid were paramount. Techniques used in-clude solvent extraction - electrowinning, evaporation - crystallization and filtration.

Jan 1, 1992

By Jun Iwai, Osamu Takai, Yasushi Inoue, Hiroyuki Sugimura

"Infrared reflection absorption measurement was performed during plasma-enhanced chemical vapor deposition of silicon dioxide films at room temperature. Hydrocarbon contaminants adsorbed onto growing film surface are oxidized by oxygen radicals in plasma resulting functional groups which include C=O and C-O bondings. These groups exist only near the surface and are hydrolyzed rapidly after exposure to air.IntroductionRecently low-temperature silicon dioxide (SiO2) deposition has been in a growing industrial demand in pa1ticular, polymelic substrates such as polycarbonate and polyethylene telephthalate, which have poor heat resistance, need low process temperature (near room temperature) in coating of SiO2 which is a suitable material to improve optical and mechanical properties of polymenc products. Plasma enhanced chemical vapor deposition (PECVD) using organosilicon reactants is one of the most promising technique for lowering process temperature, so that it has been extensively studied1-12. In the present; however, hydrocarbon contaminants and a plenty of Si-OH termination in Si-O-Si networks tend to exist in the films, which degrade mechanical, optical and electrical properties of the films. It is necessary to understand the deposition mechanism at, low temperature in order to solve the problems. We have studied the low-temperature PECVD of Si02 by spectroscopic diagnosing techniques such as optical emission and mass analysis6-7, 11- 12Infrared reflection absorption spectroscopy (IR-RAS) has been a well-established technique for characterization of thin films on metals as· well as on semiconductors and insulators13-17. In this paper, we report on' the surface reaction of room-temperature PECVD of Si02by using in situ IR-RAS."

Jan 1, 2000

By R. D. Osmanson

A series of batch roasting tests was performed on minus 1/2 inch gold bearing refractory samples from the Gold Acres deposit, and 67 select particles were polished and the sulfide alterations were examined microscopically. The suite of specimens represents two hour batch roast treatments at 600°C, 700°C, 725°C, 750°c, 800°C, and 900°C. Auriferous pyrites were found to alter sequencially to pyrrhotite, magnetite and finally to hematite. It was found that the decrease in cyanidation extraction with high temperature roasting is likely due to the increas ing stability of magnetite and more crystalline hematite, and the decrease in porosity with these phases which occlude the gold. Gold has been noted to occur very early in the mineralizing sequence, with gold being found in quartz and in clay/carbonate rock matrix. No gold was found in the two pyrite phases, but numerous gold grains were found in pyrrhotite after pyrite and in subsequent iron oxides. Gold mineralization had apparently ended by the time base metals were introduced into the deposit.

Jan 1, 1987