Search Documents

By Steven Derycke, Stephen C. Tadolini, Anand Bhagwat

"The tensile and shear strength of intrinsic bolting support systems has always been a major concern of designers. A comprehensive laboratory testing program was designed to evaluate the tensile and shear strength of individual wires and completely wound PC-strand cables. PC-strand cables with smooth wires and the recent anchorage enhancement innovation of indentation were evaluated and compared. The testing protocol detailed in ISO Standard 15630 utilizes a mandrel system that was investigated at 3 different diameters which alters the wire to mandrel ratio from 2:1 to 9:1. The results demonstrate that the difference between smooth and indented wires is statistically insignificant when larger diameter mandrels are used, and that indentation does not adversely affect strand properties and performance. Insight into the shearing mechanism and evaluation techniques are discussed with the introduction of triaxial loading to describe the PC-strand tensile and shearing mechanisms. Another important result indicates that the shear strength of PCstrand cable bolting systems has a greater shear strength value than traditional steel bar bolting systems.INTRODUCTIONPC-strand cable bolts have proven to be a global cost effective ground control solution in metal/non-metal and coal mines. The inherent strength to weight ratio of cable supports, combined with flexibility has been used in underground entries that range from 20 to less than 1.2 m in height (65 to 4 ft). In coal mining, the systems are used as primary and secondary support installed both passively or actively with installation tensions that range from 38 to over 178 kN (8,500 to 40,000 lbs) . While cable can be specified in several diameters, the most predominant sizes in the US remain 15.2mm (0.6 in) and 18mm (0.7 in). The capacity of the systems defined in the ASTM 432-13 is 90% of the minimum strand strengths of 260 kN (58,600 lbs) and 320 kN (72,000 lbs), respectively.Cables are not only suitable to support vertical loads, but are also often used to effectively support fractured and jointed materials and can be exposed to shear forces across the wound PC-strand structure. In fact, Goris et al. reported that cable bolts placed across jointed surfaces could more than double the shear resistance. These results were duplicated for both smooth and rough jointed surfaces (Goris et al., 1996). An example of tensioned cable bolts used to support a fractured and sliding roof in a longwall tailgate entry is shown in Figure 1."

Jan 1, 2015

By Winton Gale

"Rock and coal fractures and micro seismic vibration are common occurrences during development mining. It is very uncommon for coal and rock to be propelled into the roadway during normal mining operations. However, such occurrences do occur and appear to require significantly more energy than is available from strain energy release during coal cutting. The sources of energy, which can contribute to the propulsion of coal from the face or ribs, are typically strain energy from the surrounding ground, seismic energy from a rapid rupture of the ground in the vicinity, or rapid expansion of gas from within the burst source area.The aim of this paper is to briefly review the bursts that could be related to strain energy or seismic energy. However, the greatest emphasis is placed on the effect that gas within the coal could play in moderate to gassy mines.It has been found that the bursts related to the expansion of gas can occur in coal and stone. The volume of gas involved in coal bursts is typically lower than in gas outbursts; however, the process is generally similar.INTRODUCTIONA coal burst is defined as a rapid expulsion of coal (and potentially gas) from the boundary of the roadway. The volume of a burst can be variable, but volumes above 10-50m3 are noted and cause significant disruption to operations.Rock and coal fracturing is common about roadways, particularly under the influence of elevated stresses, either tectonic or related to mining abutment stress. Shear fracture is very common; however, it is very uncommon that the coal is propelled from the face or ribs as a result of fracture of the material. The nature of rock fracture about roadways under elevated stress is presented in Figure 1.A burst requires energy to propel the coal or rock from the rib or face of the roadway. The depth of material impacted may vary from 0.5m to greater than 3m inside the roadway boundary. The strength of the ground in this zone is variable depending on the nature of the coal seam (or surrounding material). Typically, this material has significant residual strength as confinement increases into the ribside.The energy required to propel this material is typically in addition to that which is associated with normal fracturing about the roadway."

Jan 1, 2018

By Dezhong Kong, Jaichen Wang, Shengli Yang

"The stability control of longwall coal face is the key technology of large-cutting-height mining method. Therefore, a systematic study of the factors that affect coal face stability and its control technology is required in the development of large-cutting-height mining method in China. After the practical field observation and years of study, it was found that the more than 95% of failure in coal face are shear failure. The shear failure analysis model of coal face has been established, that can perform systematic study among factors such as mining height, coal mass strength, roof load, support resistance, and face flipper protecting plate horizontal force. Meanwhile, sensitivity analysis of factors influencing coal face stability showed that improving support capacity, cohesion of coal mass and decreasing roof load of coal face are the key to improve coal face stability. Numerical simulation of the factors affecting coal face stability has been performed using UDEC software and the results are consistent with the theoretical analysis. The coal face reinforcement technology of largecutting- height mining method using the grouting combined with coir rope is presented. Laboratory tests have been carried out to verify its reinforcement effect and practical application has been implemented in several coal mines with good results. It has now become the main technology to reduce longwall coal face failure of large-cutting-height mining method.INTRODUCTIONLarge-cutting-height mining method of more than 3.5m mining height, is one of the main methods for thick-seam mining in China. Currently, the largest mining height is 7.3m and the support capacity is 1,800mt. Shendong and Jincheng mining area have the best use of large-cutting-height mining technology (Wang, 2009). Generally, the mining height ranges from 6.5m to 7m and the support capacity ranges from 1,000mt to 2,000mt, annual output of the panel is between 10 and 12 million tons and the highest are 15 million tons. The main goal of large-cutting-height mining technology is to achieve high yield and high efficiency by increasing the advancing speed of longwall face (Yuan, 2011- 2012). However, in certain geologic conditions, rib spalling and roof falls in the unsupported area often occur. Because of the large tonnage of large-cutting-height mining equipment, once the rib spalling and roof falls cause the equipment to be out of alignment, the face advancing speed could be affected seriously that in turn affects the output (Yang, 2012). Therefore, studying the failure mechanism and control technique of coal face in large-cuttingheight mining method is of great significance."

Jan 1, 2015

By Hamid Maleki

The U.S. Bureau of Mines implemented a monitoring program in a western U.S. coal mine for the evaluation of both conventional and alternative support systems. The conventional support consisted of 2.5-m-long vertical bolts installed in an 5.5-m-wide entry. The alternative system consisted of 2.5- and 3-m vertical and inclined bolts installed at a higher density during widening of a cut from 3.6 to 5.5 m. Roof deformation, roof stress, rib deformation, and bolt loads were monitored during the 2-month test period. In addition, roof failure patterns and lithology were characterized within the six-entry main test section. Results were analyzed using roof deformation and failure profiles, roof stress profiles. bolt loading and bending moment diagrams, and numerical models. The mechanics of roof deformation, failure, and support reaction in three zones in the mine roof were characterized. Significant improvements were shown in roof stability in the section using the alternative system. Results are encouraging and indicate the effectiveness of alternative support systems and excavation techniques for limiting inelastic deformation of roof in highly stressed underground mines.

Jan 1, 1994

By Michael Kelly

Current research in longwall mining in CSIRO Exploration & Mining is focused within five major projects and several minor projects. The major projects are: 1 3D Aspects of Longwall Geomechanics. This was reported to the conference last year and a final report will be available by mid-2001. 2 Mine Gas Control. This just completed project centred on Dartbrook Colliery which has a longwall gas make of more than 8 cubic metres per second. 3 Rapid Roadway Development This includes the construction of an autonomous conveying and bolting module (ACBM) that sits between the miner and haulage system. 4 Top Coal Caving In conjunction with the YanKuang group in China, CSIRO and the University of NSW are conducting a prefeasibility study of the Top Coal Caving method in Australian conditions. 5 Longwall Automation. In partnership with the Cooperative Research Centre for Mining Technology and Equipment (CMTE), the CSIRO has conducted a scoping study on this issue and will commence an initial three-year demonstration project in July this year. This paper describes these protects in more detail with particular focus on the last three in the above list.

Jan 1, 2001

By Rocky Wu

Rock bursts are one of the greatest challenges to ground control in the mining industry. With increasing mining depth and mining scale, there are more and more industry requirements on yielding rock support. Since 2008, Jennmar has been conducting large scale research and development works to develop a technically reliable and cost-effective yielding rock bolt. This paper introduces a new yielding rock support: the Yield-Lok bolt. The bolt is characterized by the designed yielding ability to produce 150?250 mm (6?10 in) of deflection at 8?10 metric tons (MT) (7.9?9.8 t) loads for every 16.4kJ (12,096 ft lb) energy input. The bolt?s performance characteristics are consistent through multiple and varying amplitude of impacts. In this paper, the design criteria of the bolt and the principle of performance are described; the dynamic testing results are discussed; and the features and application of the bolt are presented.

Jan 1, 2011

By Joel Bradley, Kot Unrug, Kyle Perry, Mark Klimek

"A West Kentucky mine operation in No. 11 seam, encountered floor heave, due to the localized increase of the thickness in the fireclay mine floor. Floor heave has overridden seals installed in two mined out panels. The third seal’s location was planned for isolating that area from the Mains. A plan of support has been developed to prevent repetition of the floor heave and related problems outby the seals. The applied ground control measures were successful. An attempt of a 3D numerical modeling was made, that it would match the observed behavior of the mine floor and could be used as a design tool in similar conditions. In the paper described are sequence of events, a mitigation ground control system applied, and the first stage of numerical modeling.IntroductionWest Kentucky coal mine operation in the No. 11 seam has approached an area where the fireclay floor thickness increases to about 5 ft. Delayed floor heave has been observed. In the first sealed area (Panel KK), floor heave has overridden the seals and has begun to progress outby. This could not be allowed at the new seal location PP described in this paper because such override would affect the mains. Previously numbers of standing support systems were used, but their effectiveness was not satisfactory as is illustrated in Figure 1, Figure 2, and Figure 3. Therefore, with sealing of the next area approaching, mine management was looking for a better solution that would eliminate the problem. In that stage, our team looked closely at the geology and strength of roof and floor, as well as the characteristics of ground failure around the seal at the first site. The technical literature has been searched as well Haramy et al. 1986 Hsiung and Peng 1987, Peng 2008, Santos & Bieniawski 1987. This led to the identification of factors responsible for the ground failure. It has been determined that increased fireclay thickness from typically less than 2 ft to about 5 ft, when compared to the previously mined parts of reserve, and the strong limestone strata just above the immediate roof composed of 2 ft of black shale, created conditions of failure. It appeared that, when pillars were punching into the mine floor, the strong roof did not break but was bending, exerting high pressure on outby pillars, causing rib failures and closure. This is a similar mechanism to a strong roof affecting longwall shields. The remedial action planned was additional support."

Jan 1, 2015

By Naj Aziz, Peter Craig

"Double shearing tests were carried out on the 28 mm (1 in) hollow strand Jennmar TG cable bolt to gain a better understanding of the shearing behavior of the cable. The first test was limited to a 50 mm (2 in) travel on the testing machine and produced a shear load of 900 kN (92 t) at the maximum 50 mm (2 in) displacement. The axial load generated on the cable bolt was 238 kN (24.3 t). In the second test, the machine travel was increased to 75 mm (3 in), and first strand failure of the cable, due to shear loading, occurred at 1,354 kN (138 t) vertical load at a vertical displacement of 59 mm (2.3 in). The cable axial load was in the order of 385 kN (39.3 t). Analysis of the failure mode and loads achieved showed that the cable strands bent and the concrete crushed along the shear plane; the shear loading across the concrete and grouted cable then reached the tensile strength of the steel wires.INTRODUCTIONCable bolts were introduced to the mining industry around 1970, initially to surface mining and underground metalliferous mining and then to coal mining in the early 1980s, mainly for roadway reinforcement as a secondary means of support. Cable bolts have since been used as both primary and secondary supports. As primary support, Fuller et al. (1994) described the application of cable bolts, known as FLEXIBOLT, for strata reinforcement in both Angus Place and Ellalong Collieries, in New South Wales (NSW), Australia. As secondary support, cable bolts have also been used as cable trusses, which act to support the immediate roof in a sling-like manner (Fabjanczyk and Tarrant, 1988; Fuller, et al., 1991; O'Grady and Fuller, 1992), and for reinforcement at higher stratification and beyond the rebar bolt length, mainly for anchoring lower strata layers immediately above the coal seam to the higher, competent bedding formation above. Initially cable bolt anchorage was by cementatious grouting and, since the 1990s, by chemical resin. The dominant type of cable bolts used for secondary support in Australian underground coal mines are 588 kN (60 t) capacity cables which are point anchored, pre-tensioned and post-grouted. Point anchored refers to a cable resin anchor. The cables are tensioned on the resin anchor; then the same cable is grouted by cementatious grout pumped to ·fin the annular gap around the cable from the collar of the hole to the resin anchor. Bulbs are located within the resin anchor section for mixing of the resin chemical components and efficient anchorage. The installation of these typically 8 m long cable bolts involves a lot of manual handling of the cables, lifting of heavy hydraulic tensioners, and exposure to resin grouts. Table 1 shows the specification of various cable bolts currently marketed and installed in Australian underground coal mines."

Jan 1, 2010

By Alan D. Smith

[A standardized checklist in a questionnaire format, was established to investigate selected factors associated with coal nips roof falls, as derived from an intensive review of the literature. A plot study was undertaken to aspect and explore possible statistical relationships that may exist with these parameters. the Purposes of toe study were to: 1. Study in a systematic and empirical fashion selected parameters that may be capable of differentiating characteristics of roof falls; 2. Obtain some predictive indices cased on selected physical and management related variables so that predictions of future problems associated with mine roof falls can be completed, prior to its actual occurrence. Accomplishment of these goals should result in valuable guides to the mining engineer in scheduling exploration work and 4 determining economic feasibility of certain ground control and .lining pro and practices. The parameters associated with mine roof failure that where included in the questionnaire are: working section, county, spar., orientation degrees), pillar dimensions width, length), seam thickness, roof fall dimensions (length, width, surface area, volume), shape of fall (arch, dome, laminar), thickness of thinnest immediate layer, lithology of the first four i.e.-diate roof layers, thickness of h e first four immediate roof layers, type of initial support systems before failure, type of resupport system after failure, length and spacing of bolts in use before failure, length and spacing of bolts planned after allure, presence of .cater, time failure after It coal excavation, distance t3rest ace, physical operation during, time of coo failure, location of the roof fall entry failure occurred ence of sloughing of ribs before failure, and presence of floor heave condition before failure. The typical roof fall had an average roof spar of 20.3 feet, -06 feet depth o coal seam, occurred 136 feet from nearest face, coal seam thickness of inches, p--ar :width off 45 feet surface area D' roof fall 1151 ft2, mainly lamin- shaped, previously rat fore fall between good to very good, little floor heave presence, usually cracks before the fall about 40 percent of reported cases, shales in most of the immediate layers, and usually located in an entry or intersection. in addition, multiple linear regression techniques were employed in the testing process of 18 major research hypotheses in a search for relationships among the various parameters studied of which were found to be significant, once corrected for multiple comparisons.]

Jan 1, 1984

By G. Skybey

The Directional Drill Monitor (DDM) is an advanced instrument for real time in hole surveying. It was developed by Du Pont (Australia) to suit Australian gassy coal mining conditions. The instrument consists of three units: i. Down hole transmitter ii. Acoustic transducer iii. Data receiver processor unit (i.e. up hole unit). This paper describes the function of each unit in detail and highlights the importance of the DDM in long hole drilling efficiency. Surveying is carried out independent of hole depth. Each survey takes 2-3 minutes to complete, the frequency of surveying to control borehole trajectory is determined by the accuracy required for a particular hole. The DDM is currently being used successfully for long hole drilling in a number of collieries. A high degree of directional control has been achieved. Borehole trajectories were controlled to within +l¬2m of the planned path with intersurvey distances varying between 6 to 18 metres over distances up to 700 metres.

Jan 1, 1992

By George Mishra

In mid-1979, J&L Steel Corporation experienced rapid failure of pillars after only two weeks' operation with a combination of full retreat and partial mining in the 154 Road Section of its Nemacolin Mine, Greene County. The rate of advance of the "squeeze line" was very rapid for the first 500 feet, but it slowed down considerably as it approached some large coal blocks and gas well barrier pillars. After moving all section equipment out tc a safe distance, all accessible headings and crosscuts were filled with cribs and tri-set posts to prevent further spread of the squeeze. At one time, there was great apprehension by mine management that without implementation of some immediate corrective measures the safety of #3 airshaft and the only haulage and access road to the 8 Road mining area would be in jeopardy. In September, 1979, the U.S. Bureau of Mines established convergence monitoring stations outby the squeeze area. Readings were taken at weekly intervals until January, 1980, and monthly thereafter. Mathematical calculations, plot- ting of contour maps, and graphing of total convergence at different stations were used to follow and analyze the progress of the squeeze and provide guidelines for mining plans in the adjoining areas.

Jan 1, 1981

By Sheng Zhang

The compressive strength of coal in Yanlong mine area of China is less than 3 MPa. Basically, it is powdery. The roof and floor rocks are mudstone. Therefore this coal seam is a typical ?three soft? coal seam. Roof bolting cannot be used due to the very soft strata. When the conventional U-steel support was used, roadways deformation exceeded 30% of its original dimensions in some sections one half month after development. The required repair work was huge, seriously affecting the daily mine production. This paper describes how to support the soft coal roadways. The deformation characteristics of soft coal roadway were investigated. The conventional U-steel support is not subjected to uniform load, so the whole supporting structure must be strengthened. In addition, drilling holes in the coal seam can transfer high stress from near the ribs to the deeper parts of the surrounding strata, which is beneficial to the stability of the roadway. This new support method is to combine the strengthened U-steel support with pressure-relieving drill holes, providing an economic and efficient way to support the very soft coal roadways.

Jan 1, 2013

By Kirk W. McCabe

RokLok binder is a two-component polyurethane system consisting of a polymeric isocyanate (Component A) and a polyol resin (Component B). The two chemicals are mixed and injected into the mine rock under pressure. The initial low viscosity enables the RokLok material to permeate many of the smallest fractures. About 3-5 minutes after injection, the reacting material begins to expand in the fractures; the reaction is completed after 1-2 hours, and the material sets to a mechanically strong binder which adheres tightly to the rock. The consolidated rack provides resistance to any further f movement w thin the strata. The RokLok binder injection system is fast becoming an important engineering tool for coping with adverse underground geological conditions. Two case histories discussed in this paper, a longwall mining problem and an entry-roof problem, demonstrate the effectiveness of using the RokLok binder system to help solve complex ground-control problems in a cost-effective manner.

Jan 1, 1981

By Wolfgang Schott

The propagation velocity of in-seam seismic (ISS ) waves depends on frequency which is also known as dispersion. This dispersion is not only determined by the thickness of the coal seam and its dirt hand content (i.e. thickness and position), but also by the rock type and its condition (soft or compact) above and below the coal. A coal panel completely surrounded by roadways was investigated using the in-seam seismic transmission survey technique. Along the roadways the immediate roof was either sandstone and shale- The seam thickness varied between 1.20 m (sandstone in the roof) and 1.40 m (shale in the roof) and a fault system (normal faults) crossed the panel with a total throw of about the seam thickness. Below this coal seam another coal scam with a thickness of about 80 cm exists. Its interval shown by exploratory drilling changes from about 60 cm to more than 6 m (scam splitting). Tomographic inversion was applied to the dispersion of the measured ISS waves and velocity distributions were calculated at frequencies found to he most sensitive to changes in the seam thickness and the distance to the coal seam below. By correlating the velocity distributions with known values along the roadways approximate distributions of the coal seam thickness and the seam splitting within the panel were produced. The mining of the coal panel had already been finished and comparison was made between the survey results and the actual situation as far as it was documented. Prediction by the seismic survey was partly in good agreement with the actual held conditions or showed at least the same trends.

Jan 1, 2003

By Liane J. Terrill

A 9O) ft (275 meter) section of a highly fractured beam of halite was mined from the roof of a supported thirteen year old drift at the Waste Isolation Pilot Plant (WIPP). The operation was conducted with a continuous miner and allowed the unique opportunity to collect spatial information on roof beam geology and to observe ground support conditions during the mining advance. Photographs and fracture maps of the mining face document the progress of the operation and the deteriorated condition of the strata. This case study details the drift's excavation and support sequences. the geomechanical response, and the conditions found in the exposed roof beam.

Jan 1, 1997

By David R. Hanson

Seismic tomographic imaging, based on the same principles as a medical CAT Scan (Computer-Aided-Tomography). has been used for many years in the oil industry for large-scale subsurface stratigraphic characterization. and has most recently been applied to various structure- and stress-related problems in the coal industry. New developments in signal processing have greatly enhanced the speed, resolution, and range of applications of topographic imaging in underground settings, and recent innovations in data acquisition hardware have further increased data reliability and repeatability. Whereas past structure mapping applications relied on Seismic velocity and/or attenuation tomopraphy within an enclosed seismic source gram receiver array, recent developments in "True Reflective Tomography- (TRT TM) have expanded the application of this technology considerably. For example, in-seam TRT TM seismic reflection tray now he used to image structure, and/or old workings from one general location in the mine face areas of mains and panel developments) well ahead of planned developments largely eliminating the need to probe-hole drill on regular intervals. This new reflective technology bas also been combined with traditional cross-hole seismic tomography-providing a comprehensive, powerful tool for velocity attenuation. and reflective imagine utilizing the same source/receiver array data sets (borehole-to-borehole. borehole-to-entry and entry-to-entry). These new developments in data acquisition and image processing have greatly expanded the variety of applications for tomographic site characterization allowing the mine operator considerable flexibility to cost-effectively characterize previously inaccessible areas of the property. This paper presents examples of 2-D and 3-D .seismic topographic imaging applied to (1) the location of old works in Appalachian room-and-pillar operations and (2) the identification of anomalous zones ahead of mining/tunneling developments these applications demonstrate the state-of-the-art in seismic ground imaging using velocity, attenuation. aril reflection techniques land combinations thereon, and further illustrate the flexibility of data acquisition from a variety of tinning arid tunneling settings. Recent examples are presented from projects in the United States and Europe.

Jan 1, 2000

By Axel Preusse

Due to a political decision, German hard coal mining will come to an end in the year 2018. By then, there will have been more than 150 years of industrial grade mining activities. Located in the western part of Germany is one of the most densely populated areas of Europe. Multiple coal seams have embossed the earth?s surface up to 20 meters (21.87 yards), as mining has subsided. The aftercare of hard coal mining will consist of three tasks: groundwater management, polder management, and groundwater treatment. The Ewigkeitslasten (cost in perpetuity) at the current groundwater level has been determined in the past. The actual cash value is calculated to be about 12.4 billion euros (approximately 16.5 billion dollars). The cost of groundwater management is directly related to the groundwater level. Rising groundwater levels will reduce the cost of pumping water. Known effects of rising groundwater are uplift of the surface, emission of methane gas at the surface, higher risk of cave-ins, and contamination of drinking water horizons. Each of those processes produces cost in order to prevent negative consequences (e.g., uncontrolled methane emissions) or to handle reparations (e.g., damages caused by surface uplifts). In the long run, it is the goal to minimize the Ewigkeitslast. As a first step, all cost-generating processes are specified, and a cost type based characterization is performed. The objective of this case study is to identify key parameters to determine the quality of a cost-generating process (proportional cost, fixed amount cost). Afterwards, it is intended to specify the quantitative impacts of each parameter and to set up an optimization model to minimize the overall cost. The quantitatively specified parameters will form the base out of which the optimization model is created.

Jan 1, 2013

By André Zingano

Pillar collapses have been studied for several years and can be classified into two types: nonviolent squeeze or violent pillar collapse, i.e., controlled or uncontrolled pillar collapse. Underground coal mines in Brazil are considered shallow mines, because the overburden thickness varies between 20 and 400 meters. For this reason, the coal pillars should be designed as permanent pillars to avoid subsidence and groundwater problems. In the last two years, various pillar collapses occurred, one being a violent collapse and the others being squeeze collapses. All these collapses were considered massive pillar collapses because many pillars were involved. In the violent pillar collapse case, the width¬to-height (w/h) ratio was less than three; although, the pillar safety factor (SF) was more than 1.3. There was a collapse of about 100 pillars in less than three hours. The objective of this study is to determine the mechanism of pillar collapse for this violent pillar collapse. Convergence monitoring and numerical modeling were applied to combine field data and theory to simulate the pillar collapse. Convergence field measurements introduce the arc-effect behavior for the roof. The results showed that other factors besides pillar geometry caused the pillar failure. Other parameters, mainly dip of the coal seam and presence of fractures and faults may affect the strength and failure mechanism of a pillar.

Jan 1, 2004

By George J. Karabin

The Roof Control Division of the Pittsburgh Safety and Health Technology Center, MS HA, is routinely involved in the evaluation of ground conditions in underground coal mines. Assessing the stability of mined areas and the compatibility of mining plans with existing conditions are essential elements in assuring a safe working environment at a given site. Since 1985, the Roof Control Division has successfully used the Boundary Element Method of Numerical Modeling as a tool to aid in the resolution of complex ground control problems. This paper will present an overview of the modeling methodology established and details of techniques currently used to generate coal seam, rock mass, and gob backfill input data. A summary of coal and rock properties used in numerous successful evaluations throughout the country will be included and a set of Deterioration Indices that can aid in the quantification of in-mine ground conditions and verification of model accuracy will be introduced. Finally, a case study will be detailed that typifies the complexity of mining situations analyzed and illustrates various techniques that can be used to evaluate prospective design alternatives.

Jan 1, 1994

The objective of extensive underground experimentation on three longwall coal faces was to improve the stability of mechanised longwall faces through investigation of the relations between support resistance and convergence and resultant deformation of roof and face strata. In particular the influence of high setting and yield pressures on several strata and support parameters was studied in great depth. Increased setting pressures resulting in an increase in setting load densities from 0.15 MN/m2 to O.45 MN/m2 were shown to reduce convergence, face spalling roof flaking, lateral movement of roof and floor, extrusion of the face wall and progressive failure of the coal wall ahead of the face. This was shown to result mainly from the change in roof strata deformation from a wedge shaped compression zone with tension at the face edge to an even beam shaped compression zone over the face area. Debris thickness above the support canopy and below the base was observed to be the one of the most variable parameters which influenced the support characteristics particularly the rate of load acceptance by supports and the roof to floor convergence. A setting load density of 0.4 MN/m2 to 0.5 MN/m2 was found to be optimum under soft to moderately strong sandstone roofs. The authors demonstrated that use of guaranteed set valves with powered supports contribute to good strata control, reduce face down-time and increase face productivity.

Jan 1, 1984