Search Documents

By Peter Zhang

The immediate roof at the test site consisted of laminated clay shale that is likely to be susceptible to weathering. With seasonal dry-wet cycles in the mine ventilation air, the roof in the intake air would deteriorate and lose integrity over time. In many instances, the weathering-prone roof would gradually scale off piece by piece between bolts and over the entry corners. In some long-term entries, roof weathering could develop up to 2-3 ft deep with columns of bolted roof hanging under the upper intact roof. If wire mesh is used, the roof bags down and reduces the entry height, and the weight of the bagged roof tends to pull the bolts out and poses a safety hazard. An effective measure is always sought to support this type of weak roof that is sensitive to moisture degradation. One solution is to seal the roof shortly after entry development to prevent moisture penetration so that roof integrity can be maintained for the long term. In this application, a polymer-based sealing material was tested in the Rockspring mine for weathering protection and reinforcement. The material is a one-component polymer powder for spray application onto the roof and rib. The sealant material is mixed with water in the spraying nozzle to apply to the roof and rib as a paste. The product sets within 5-10 minutes and forms a membrane as thin as about 1/8-in. The membrane will quickly develop tensile and bonding strength within minutes and completely cure within a few days. Through sealing, bonding and lateral reinforcement, the integrity of the weak roof can be maintained. The material has been tried in a long-term evaluation over several months in a set of main entries in the Rockspring mine owned and operated by Rockspring Development, Inc., affiliate of Foundation Coal. Preliminary evaluation has shown that the material is an effective and economical solution to ensuring the long-term stability of weathering-prone roof.

Jan 1, 2009

By Michael Alber

Resin grouted rock bolts are the major support measure in coal mining. They are rather easy and foolproof to install, take immediately load and are the least time consuming support measure for controlling gateroad deformation. The use of only resin grouted bolts allows fast gateroad development which is essential for economical resource exploitation. The design of reinforcement / support systems for coal mining typically bases on empirical methods, which work fine when encountering known or usual ground conditions. However, coal mining approaches depths where little experience exists and numerical modeling is often the only method to estimate ground behavior. This paper discusses the geotechnical properties relevant to numerical model and focuses particularly on input values for modeling resin grouted rock bolts for safe gate design.

Jan 1, 2006

By Qingxiang Huang

Shallow seam coal field has the largest coal reserve in China. Mining in shallow depth causes serious problems. One of them is subsurface dewatering. In this paper, the physical simulating model was performed to study overburden movement and aquiclude stability in the shallow seam mining of Yushuwan coal field, China. According to the characteristic of clay aquiclude in the overburden, the proper simulation materials and proportions of mixture for simulating the plastic clay aquiclude layers and brittle bedrock layers were determined by the stress-strain tests. The physical simulating model was carried out to simulate the failure and caving process of the roof and overburden. Based on the simulating tests, it was found that the movement of clay aquiclude follows the movement of the underlying bedrock layers. The basic caving mechanism of the overburden roof strata was also presented. The tests also showed that the best way to control the stability of aquiclude is to reduce the subsiding gradient Ts. This research provides a foundation for further study on mining dewatering and water conservation.

Jan 1, 2006

By S. Yamashita

Recently in Japan, unexpected degradation (surface subsidence) at old underground quarry sites, such as 'Ohya-Ishi' (pumice tuff) pit field has often been occurred. At these quarry sites, the excavation was started 20 or 30 years ago with mechanical chain cutter and the Room and Pillar method, and stopped 7 or more years ago. Therefore, a reliable method has been required for an estimation of long term mechanical properties of the rock and for an observation of a stability of rock-pillars or structures. In this study, creep tests under uniaxial compressive load were carried out on the 'Ohya-Ishi', with the aim of estimating the long term stability of the rock. From these results, a creep mechanism of the rock was discussed using the failure mechanism hypothesis proposed by Bieniawski and by others. On this basis, critical time to failure was predicted by the relationship between the logarithm of life time and stress ratio of the sustained axial creep load. Additionally, outline of the monitoring system of AE/MS activity in the field, which have set by the Ohya Aria Consolidate Public Corporation and the others to predict or to prevent the degradation of those residual pillars, is to be reported. Key words : Ohya-ishi, Pumice tuff, Mine pillar, Long term stability, Creep, Critical time

Jan 1, 1996

By R. B. Alke

Request to Mine Beneath Bridge The Jabs Run Bridge is a reinforced portland concrete arch filled bridge located on WV Bouts 7 near Pentress, WV. The bridge has a span of 22.9 m (meters) and a height of 4 m above normal pool elevation to the underside of the center of the arch (See Pig 1). The bridge is a two lane structure with a width of 6.86 m. The structure is over 50 years old Wing been built in 1929 and is owned by the Department (WV Department of Highways).

Jan 1, 1984

By D. J. Reddish

An understanding of the mechanisms that cause large seismic events in a deep mine provides a foundation for designing effective measures to reduce the incidence of these events, as well as reduce the potential for damage arising from these events. The work described in this paper focuses analytical efforts on major recognizable and controllable factors that influence mining-induced seismicity and serves to screen out many of the more random aspects of individual events. Information used in this study was developed in the course of a long-standing rock burst research program conducted by the U. S. Bureau of Mines in cooperation with mines in the Coeur d'Alene Mining District and regional universities. Information was collected on 39 seismic events having local magnitudes greater than 2.5 that occurred between 1989 and 1994. Five major types of events were developed from these data that describe all but two of the 39 large events. The characteristic mechanisms, tint-motion pattern, damage pattern, and relationships to mining and major geologic structures were defined for each type of event. This information provides a foundation for assessing whether or not changes in mining activity aimed at reducing one type of rock burst will increase the incidence of other types.

Jan 1, 1996

By A. MacG. Robertson

A cone penetrometer has been used to assess the level of stress existing in hydraulically placed mine backill. The test apparatus was fabricated at the mine and consisted of a steel cone, connector rods and a hydraulic jack. Testing was carried out from a manway passing through the centre of the stope. The cone was pushed horizontally into the fill, both at right angles and parallel to the orientation of the stope walls, and the resistance to penetration was measured. Corrections were made to allow for friction along the rods. In a cohesionless sand, such as mine fill, the point resistance should be directly related to the in situ stress. The stresses in mine backfill are due to o the self weight of the fill o convergence of the footwall and hangingwall of the stope. Silo theory was used to estimate that component of the in situ stress due to the self weight of the fill. The difference between the stress predicted by silo theory and the stress estimated from the cone resistance was assumed to be due to convergence of the stope walls.

Jan 1, 1986

By Rebecca Hardy

The escalating demand for coal, in addition to the steady depletion of reserves, has produced increasingly difficult mining conditions for coal mining companies within the United States, resulting in mining above or below previously mined areas. The safe and productive extraction of coal in a multiple seam environment requires specific design technology for effective mine planning. Presently, one of the most useful design approaches for multiple-seam feasibility analysis is using numerical modeling techniques. Therefore, numerical modeling programs LaModel 2.1 and Lam2D were used to determine the feasibility of mining the Herrin (No. 6) coal seam over an existing room-and-pillar mine in the Springfield (No. 5) coal seam in the Illinois Basin.

Jan 1, 2006

By Axel Studeny

Geomechanical-numerical methods are an established tool for planning of underground excavations worldwide. By describing the interaction between heterogeneous layered strata and support elements it is possible to determine their suitability. The German hard coal mining industry has more than twenty years experience in investigation and using these parameters to carry out numerical calculations. Today, nearly all excavations (shafts, pit bottoms areas, bunkers, coal faces, development drivages, gate roads etc.) are calculated by geomechanical-numerical tools in combination with empirical planning methods. A high accuracy of planning results, which is a special requirement in the German coal industry with its deep-level longwalls, bedded and weak surrounding strata and multiple seam mining layouts, depends on the extensive calibration of the numerical models, which is achieved by: 1) Taking a large number of underground measurements with empirical evaluation. 2) Carrying out physical modeling. 3) Using the characteristic features of the installed support elements. This paper compares the planning approach used for multiple and single seam mining and presents the advantages of this planning tool. The main focus is on the feasibility of rockbolting as the sole means of roadway support for multiple seam mining operations, though the paper will also look at how the costs can be improved by using a low bolting density in single seam layouts.

Jan 1, 2007

By Stephen C. Tadolini

The U.S. Bureau of Mines, in cooperation with the Cyprus- Plateau Mining Company, has conducted research to provide an alternative to traditional secondary support systems in a two-entry, yield pillar gate road. As recent as two years ago, it was impossible to imagine a gate road supported solely with internal high-strength resin-grouted cable supports that would virtually eliminate the necessity for crib or concrete external supports. The support system evaluated consisted of 1.6-m (5-ft) full-column resin-grouted bolts and 4.8-m (164) long cable supports installed in conjunction with wire mesh and "monster-mats." Cable loading and roof deformations were monitored to evaluate the behavior of the immediate and main roofs during first and second panel extractions. The stress and loading histories for the panels and yield pillar were monitored to evaluate the stress transfer and pillar performance in conjunction with the roof and floor behavior. The test results indicated that the designed support system successfully maintained the roof during the extraction of two longwall panels and dramatically reduced the cost of secondary support. This paper will describe the theory of a cribless support system, the advantages of cable supports, and present the pillar, roof, and floor measurements made to assess the support performance during longwall retreat mining.

Jan 1, 1995

By Alan A. Campoli

The U.S Bureau of Mines is conducting research to develop improved guidelines for selecting the type and pattern of roof support in different geologic environments (Mucho, et al., 1995). As a part of this wider research effort, a multifaceted ground control investigation was conducted at the Diamond TB Mine of RoxCoal, Inc. The study included statistical analysis of mine-wide roof bolt performance, instrumented bolt test areas, stress damage mapping, and pillar design analysis. The mine employs state-of-the-art continuous miner technology, including mobile roof supports and continuous haulage, to retreat mine the Lower Kittanning Coalbed. A herringbone section design makes the stability of the center belt entry critical to efficient retreat mining. Roof cutters formed during section development sometimes set up unstable immediate roof conditions in advance of the belt entry mobile roof supports during retreat mining.

Jan 1, 1996

By Theresa M. Bodus

The strength of roof shales is, in part, a function of the preferred orientation of clay minerals within them. Therefore, analysis of clay fabric under both air-dried and hydrated conditions should be helpful in understanding roof shale failure. Core samples were collected from the Energy, Anna, and Lawson shales, which are locally present as roof shales of the Herrin No. 6 coal of southern Illinois. The Clay Fabric Index (CFI) was measured for thirty core samples, using X-ray diffractomtry, to investigate the relationship between clay fabric and roof collapse in coal mines. Greater CFI values indicate a weaker preferred orientation among clay minerals, which generally results in a weaker inter-grain bond. Average CFI values for air-dried samples were: 0.15 for Anna shale; 0.20 for Energy shale; and 0.37 for Lawson shale, .After the introduction of water, average CFI values increased to: 0.28 for Anna shale; 0.22 for Energy shale; and 0.43 for Lawson shale. The laboratory results indicate the following: [l] under air-dried conditions, Anna shale is the most stable, followed by Energy and Lawson shales; and 121 under hydrous (mine) conditions, Energy shale is the most stable, followed by Anna and Lawson shales. In mine environments where roof failures involving Energy shale have occurred, planar trends delineated by a relatively high density of small (0.2-4 cm diameter) iron concretions have been reported along the failure surface. Radial cracks have been observed around unsealed anchor bolt holes in the Anna shale. Instability of the Lawson shale is ubiquitous in coal mines. In the laboratory, similar physical changes were noted in the shale samples after the introduction of water, including [l] increased hydration around the perimeter of iron concretions in Energy shale, [2] radial extension cracks in Anna shale, and 131 extreme slaking of Lawson shale. Measured increases in the CFI reflect the observed physical changes of the samples upon the introduction of water, which probably reflect changes in strength that may result in roof failures in hydrated mine environments.

Jan 1, 1989

By Zach Agioutantis, Christopher Mark

"Thirty years ago, the Analysis of Longwall Pillar Stability (ALPS) inaugurated a new era in coal pillar design. ALPS was the first empirical pillar design technique to consider the abutment loads that arise from full extraction, and the first to be calibrated using an extensive database of mining case histories. ALPS was followed by the Analysis of Retreat Mining Stability (ARMPS) and the Analysis of Multiple Seam Stability (AMSS). These methods incorporated other innovations, including the Coal Mine Roof Rating (CMRR), the Mark-Bieniawski pillar strength formula, and the pressure arch loading model. They also built upon ever larger case history databases and employed more sophisticated statistical methods.Today, these empirical methods are used in nearly every underground coal mine in the US. However, the piecemeal manner in which these methods have evolved resulted in some weaknesses. For example, in certain situations, it may not be obvious which program is the best to use. Other times the results from the different programs are not entirely consistent with each other. The programs have also not been updated for several years, and some changes were necessary to keep pace with new developments in mining practice.The Analysis of Coal Pillar Stability (ACPS) now integrates all three of the older software packages into a single pillar design framework. ACPS also incorporates the latest research findings in the field of pillar design, including an expanded multiple seam case history data base and a new method to evaluate room and pillar panels containing multiple rows of pillars left in place during pillar recovery. ACPS also includes updated guidance and warnings for users and features upgraded help files and graphics.INTRODUCTIONPillar design is one of the fundamental elements of mining engineering. Pillars are necessary to control the great weight of the overburden during all phases of underground mining. Without stable pillars, ground control is impossible."

Jan 1, 2018

By Gerald L. Stolarczyk

Safe and efficient coal extraction requires advanced radar subsystems that can be mounted on cutting drums of coal cutting machines. A look-ahead radar (LAR) must solve the radio geophysics problem of transmitting an electromagnetic (EM) wave through at least 20 feet (6.1 meters) of coal to an air- or water-filled void. The reflected EM wave must be processed in the radar electronics to determine the physical distance to the void. Horizon sensing enables selective cutting near the undulating sedimentary rock boundaries of the coal bed to address coal quality and ground control issues. Both sensors require subsystems for dynamic electric power generation, real-time measurement of drum rotation angle, detection of reflected EM waves, and processing to determine distance through coal and RF modem transmission of measured data to the mining machine. This paper describes the development of the subsystems and field test results.

Jan 1, 2006

By Yi Luo

In dealing with various subsidence cases, accurate predictions of mining induced subsidence are the basis for correct assessment of subsidence influences and subsequent mitigation efforts. There is a good demand for a reliable tool to perform the subsidence predictions and related tasks. A comprehensive and integrated subsidence prediction model, CISPM, developed by the senior authors in the later 1980?s and early 1990?s (Peng and Luo, 1992) is one of such tools. Built on solid mathematical models and calibrated by a large number of collected subsidence cases, CISPM provides a rich set of features needed in subsidence engineering and research works. Its reliability and usefulness have been proven by numerous field applications. This upgrade of CISPM will not only preserve its original features and reliability but also provide some new needed features and a more user-friendly working environment.

Jan 1, 2008

By Yemi Akinkugbe

Underground coal mining under massive sandstone can present significant challenges if the roof behavior is not well understood. This paper presents a classic cantilever bending/flexing behavior of a longwall tailgate roof caused by the weighting of structurally massive sandstone strata. Nineteen crosscuts of a longwall tailgate under massive sandstone were instrumented with position transducers connected to a data-logger to monitor roof convergence as the longwall face approached. During the monitoring program, an unusual tailgate roof divergence (uplift) was recorded. This roof behavior contradicts expected norm of roof convergence when the longwall is influenced by periodic weighting. The recorded roof movement data indicated that the roof divergence started well ahead of the longwall face. The most inby position transducer started recording progressive roof divergence when the longwall face was approximately 643 feet away. Very gradual roof convergence did not begin until the longwall face got to within 300 feet of the transducer. Recording of accelerated convergence only started after a massive caving event with the face within 280 feet of the recording transducer.

Jan 1, 2007

By R. D. Yancich

A case study of longwall mining surface subsidence was performed at a mine in Southwestern Pennsylvania. The mine operated in the Pittsburgh coal seam which averaged 70-72 inches with 6-8 inches draw slate in the longwall location. The average overburden depth ranged from 625 8eet to 660 feet. Three adjacent longwall panels were studied and classified as Panel 1, Panel 2, and Panel 3. The following is information on each and can be seen on the General Mine Map (Fig. 1).

Jan 1, 1984

By D. S. Choi

This paper describes an improved source location technique for microseismic events related to coal mining. A system of non- linear distance equations is solved with the use of the Newton-Raphson method. This computational method is- advantageous when the number of geophones is limited. In addition, this paper includes the results of the analysis of data from several instruments which characterize both mine seismicity and environmental noise such as vehicle traffic. Analysis of the mine seismicity has contributed to a better understanding of caving above a longwall gob and of what constitutes stable ground conditions.

Jan 1, 1990

By Thomas M. Barczak

The intent of this paper is to make mine operators and engineers aware of parameters which affect the loading behavior of passive roof support systems. The strength of a passive roof support element alone is not a meaningful measure of support performance. Passive roof support elements and the surrounding strata act as a system, responding to changes in the physical mine environment due to the extraction of coal and associated redistribution of stresses. The load- ing of a passive roof support element is a function of the stiffness of the roof support structure; a stiffer structure will react a higher load to a converging mine roof than will a more flexible structure. If the stiffness if the support structure is not properly designed, excessive loading will result due to the displacement of the mine roof, causing premature failure of the support. Ideally, the yield strength of a passive support needs to be no greater than that required to support the dead weight of the immediate mine roof, providing the post yield characteristics of the support are compatible with the irresistible convergence of the overburden strata and the support system continues to provide this resistance after reaching its yield load. Idealized design considerations for passive roof support systems in terms load-displacement characteristics discussed. The stiffness and yield characteristics of wood concrete cribbing, as determined controlled tests in the Bureau's Roof Simulator, are compared preliminary recommendations passive roof support utilization also provided.

Jan 1, 1987

By J. Willan

This paper addresses the problem of designing a destress blasting procedure to reduce the incidence of rockbursting in hard rock mines. A review is made of the developed theory and practice of destress blasting in rockburst-prone ground. Specific reference is made to a recent survey of past and current practice with particular reference to Ontario mining operations. The need is identified for a more scientific basis for destress blast design and monitoring. Reference to developments in blasting technology as well as rock mechanics are then made to support a proposed, integrated design procedure and research strategy.

Jan 1, 1984