Search Documents

By A. J. Kroha, N. Wesis

Most copper mines produce both ore and low-grade "leach" rock or acid waters that contain recoverable copper. The sulfide ores pre¬dominate, and a portion that is too low grade for milling to produce concentrates for smelting, but has to be mined and trucked away anyhow, may be leached successfully with acid in dumps. Most of this leach material consists of sulfides and silicates or carbonates, and if the gangue is such that it consumes a high quantity of acid, this factor may rule out a leach operation. There are also valuable deposits that contain mostly acid-soluble copper, or occasional sulfide ores from which a sulfide concentrate can be roasted and acid-leached to produce a copper-bearing solution. Finally, there are milling ores in which the lesser part of the copper is acid-soluble and can be precipitated with iron or synthetic inorganic precipitants that produce metallic copper or copper sulfides that will float with the sulfides. Ordinarily, ores that contain copper associated with the sulfur ion, such as in the minerals chalcopyrite, chalcocite, bornite (and others), are milled to produce a 25-30% Cu concentrate for smelting, while a lesser amount of acid-soluble copper may be converted from solution to cement copper on iron scrap. A fast-growing percentage of such copper, however, is removed from solution with exchange resins or organic compounds in organic carriers such as kerosene (solvent extraction), then eluted with strong acid and subjected to electrolytic precipitation either in marketable form or as anodes that can be refined further. From the point of view of conventional copper smelting, copper flotation concentrates and cement copper are of chief interest in this chapter. Table I is a condensed open schedule for concentrates that generally run between 25 and 35% copper, and much less frequently as low as 12-15% or as high as 65-75% copper, the former being due to intimate relationship with pyrite (like the former United Verde Extension), and the latter representing such ores as the Bolivian Coro¬coro ore in which the copper is in the form of chalcocite in sandstone. These extremes are no longer common. When they occur, a special purchase schedule has to be negotiated. Included in Table 1, copper precipitates (cement copper) generally run from 70-85%a copper, and the same basic purchase schedule is used as with flotation concentrates. Sulfide Flotation Concentrates The sulfide copper concentrate produced in the mill as a flotation froth, with water then added for transportation of the heavy mineral particles from the flotation cells to thickeners, may run 60-80% water by weight, and the removal of water down to 25-50% by weight by means of thickeners, followed by further dewatering by continuous vacuum filters to 7-18% moisture by weight (depending on size of solids by screen analysis and also by content of clay) is a critical operation. Mill operators would like to produce a filter cake with 7-9% moisture content, but even with the help of steam on the filter this desirable condition is seldom realized when the concentrate is as fine as 80% -325 mesh. More commonly, the final concentrate is reground in pro- to produce best copper recovery and grade of concentrate (or molybdenite separation). In those cases, increasingly frequent, the filter product may not be a cake at all, but a mud that is hard to handle-even requiring a thermal dryer. Greater difficulty of form¬ing a manageable cake often comes from the copper-molybdenum separation by flotation, because the alkaline sulfides and hydrosulfides, or cyanide, or other similar reagents used for the separation, may leave the now relatively molybdenite-free copper concentrate even more difficult to filter. Handling a wet filter cake is difficult enough when its destination is only a short distance away-a matter of yards rather than miles. In those cases the filter cake may be thermally dried near the point of production, using rotary or multiple hearth, or fluidized-bed dryers. Alternatively, the concentrate may be pumped or carried in slurry form to the smelter and filtered there, or it may be spray-dried and compacted. For transportation to a smelter just a few miles to a few thousand miles away by ship or railroad other factors may be important, such as: in shipping by sea, avoidance of spontaneous combustion; in shipping by rail, losses by leakage if too wet or by wind and sun if too dry. It is the responsibility of the millman-usually the mill superinten¬dent-to make sure that his concentrates are in satisfactory condition when they leave the mill so that they meet these requirements: 1) They must have been accurately sampled and dry-weighed, the latter meaning that a moisture determination and gross weight must have been taken. 2) They must be dried sufficiently when necessary to prepare them for safe transportation. 3) They must arrive at the smelter with reasonable likelihood that they can be check-weighed and sampled fairly and equitably,

Jan 1, 1985

By MAURICE SUNKPAL, Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

In this study, various rib bolting scenarios were investigated to better understand the effectiveness of the support systems. A coal mass constitutive model is implemented to a distinct element method (DEM) code, and rib factor-of-safety (RibFOS) analyses were performed by applying strength reduction for the coal matrix and explicitly modeled face cleats. Ribs with various overburden depths and mining heights composed of solid banded bright coal were considered. Different scenarios such as rib bolt length and number of bolts were studied to quantify the effect of primary rib support density on rib stability. As a result of the unsupported coal rib analyses, a decaying exponential relationship is proposed between the mining height-overburden depth and the RibFOS. The developed coal rib models clearly show the coal-rib bolt interaction and illustrate how the addition of rib bolts restricts the movement of the coal rib. The results reveal that the strength-reduction method in DEM code with the coal-mass model can aid in the development of practical primary sup- port charts, which can help in the rib support design process.

Feb 1, 2024

By Hun-Joon Sohn

Chemical metathesis and electrochemical reductive conversion of chalcopyrite in the presence of cupric ions were studied in sulfuric acid solutions for temperatures up to 90°C. The process results in the displacement of iron in the chalcopyrite lattice by copper ions with rejection of ferrous ions to the aqueous phase. The rate of reaction was found to be very slow, requiring subsieve-sized particles for extensive reaction to occur. The reaction was insensitive to copper ion concentration. Stirred ball milling of chalcopyrite introduces lattice strain. The reaction rate with strained particles was markedly higher than with annealed chalcopyrite. The reaction rate was found to be diffusion-limited, showing two distinct reaction stages corresponding to the formation of CuS (covellite) followed by Cu1.8S (digenite). The experimental activation energy for the first stage was 102 J (24.4 kcal) and the second stage 123 3 (29.4 -kcal) per mole. The rate-controlling process is diffusion of lattice ions, probably iron. The enhanced rate after milling is attributed to a recrystallization process which provides new paths for diffusion along dislocations and grain boundaries.

Jan 1, 1984

By Nikolaos Syrtariotis, Mark Berger, Timothy O’Brien, Vojtech Gall

The Northeast Corridor Superconducting Maglev Project (SCMAGLEV) entails construction of a high-speed train system between Washington, DC and New York City, with the first leg between Washington and Baltimore, MD. This innovative project will shorten travel times between Washington DC and Baltimore to approximately 15 minutes, and connect Washington, DC to New York City in under an hour. In 2021 the draft EIS is expected to be issued for comment with a Final EIS/ROD anticipated by early 2022. This paper provides an update on the project as presented in Gall et al. (2020) and discusses the economic and environmental benefits, preferred alignment alternative, preliminary staging and launching of the TBMs for construction, and preliminary station design.

Jun 13, 2021

By J. Seifert, L. Hunter, P. W. Conrad, S. Rosenthal

"The goal of the protocol for reclaiming in-pit tailings ponds to exceed federal and state regulations was to develop a series of steps that can be followed to design, operate, and reclaim a tailings disposal pond that will develop into grazing land with a wetland for open pit sand mines in warm dry climates. By incorporating a wetland into the reclamation design, the post mining land use gives back to both the wildlife as a source of water as well as providing for a diverse range of post mining land use including but not limited to livestock grazing and ranch land use. An example design was completed using this protocol to demonstrate how the protocol can result in in a well-designed, reclaimed tailings disposal pond. BACKGROUND In an industry plagued with decaying historic mine sites, the public’s perception of mining appears to be poor. While modern mines are closely monitored and generally managed by ethical professionals, history still influences how the public perceives the mining industry. From collapsing abandoned underground workings to historic tailings dam failures, the failure to account for the environment in the past seems to affect public perspective on mining today. In a 2013 “Opinion Former Survey,” a survey conducted through interviews with a diverse range of stakeholders in various gold companies, it was noted that the most serious challenges facing the mining industry were environmental concerns and the permitting challenges associated with them (Council). In another article, this time focusing on Australian citizens and their perspectives of the mining industry, it was found that the majority of those surveyed had a big concern over the environmental impacts of mining especially when it comes to water quality and quantity (Scan). The statistics portrayed in these articles illustrate that today’s mining engineers needs to make more of an effort to change the public’s perspective of mining by being more environmentally aware. These engineers should be continuously asking themselves what they could be doing better from an environmental perspective to ensure that history is not repeated and that natural resources are used as efficiently as possible."

Jan 1, 2018

By K. E. Yassin, A. Yehia, M. Amar

Phosphate ores are the source of many commodities, such as phosphorus element, P2O5 and fertilizers. Discarding a large percentage of fine phosphate particles produced as slimes during phosphate ore processing represents a severe environmental problem, besides making the beneficiation process uneconomical. The phosphate industry is interested in a process that is efficient, with high grade and high recovery; ensures economical feasibility, with low operating cost; and is environmentally sound, with low toxicity. Numerous investigations have been conducted to try to find better processing techniques and reagents. However, reagent requirements and recovery limitations may be so high that the end does not justify the means. Reagents of biological origin are of special interest because they offer specific interactions with minerals, reduced operating costs, environmental acceptability and flexibility in adaptation. Recently, there has been a growing interest in using microorganisms as flocculants for mineral fines and as flotation collectors. 

By SIMON DIAZ-QUEZADA, HUMBERTO ESTAY

The heap-leaching process is widely used for recovering different metals. In Chile, copper production by heap leaching has been accounting for between 30 and 40 percent of annual copper production over the last 10 years. This level of production has been achieved through and supported by the use of a mathematical relation known as the leaching ratio (LR), which correlates operational parameters with metal extraction in a heap-leaching operation. In spite of the widespread industrial use of this relation, few scientific studies mention it. This disparity between industrial practice and scientific research could lead to operational decisions that lack substantial theoretical support and to scientific studies with limited industrial impact. This study describes the LR and its current uses and limitations.

By J. W. C. Wong, S. D. Miller, J. J. Jeffery

Pre-mining identification of acid forming mine and waste materials is of concern to the mining industry because of the potential for the generation of acid mine drainage, acid rock drainage, and soil acidity problems. Accurate identification of acid forming material is essential for developing appropriate waste management strategies to reduce environmental problems related to acid generation from sulphide containing wastes. The acid-base accounting procedure, in its various forms , is commonly used for pre-mining screening of mine and mine waste materials. The procedure is generally effective when used and applied correctly but is prone to incorrect interpretation of results which can have significant financial and environmental implications. This paper examines the acid-base accounting Procedure and the possibility of misuse of this method with special emphasis on the sampling method, the sulphide forms, the acid neutralization capacity, and the interpretation of results. Data from numerous coal, base metal, and gold mining operations are used to illustrate the application of the acid-base account. The data base indicates that overall, approximately 1/3 of all waste generated by mining and mineral processing is potentially acid forming indicating the need for correct identification and management. Problems associated with simple application of 'absolute' acid-base criteria for classifying acid forming material are highlighted and the need for developing site specific or 'relative' criteria is discussed and illustrated by case study.

Jan 1, 1991

By Jr. Zink

An economic and operational evaluation of the unrecovered metal, physical conditions, and chemical environment in a leach pad should be made prior to decommissioning. This evaluation will help determine the possibility and method of secondary and/or enhanced metal recovery and the method(s) to be used for detoxification and heap closure. The evaluation requires quantitative sample collection in a locally variable, yet grossly homogenous material. An assessment of a valley fill heap leach pad was made using a technique borrowed from placer technology called sonic drilling. The sonic drilling technique produced very satisfactory core recovery and sample quality. At this site, drilling results demonstrated that the method of heap construction produced expected features after extensive long term leaching. Rather than a uniformly homogenous pile of metallurgically depleted crushed ore, an assemblage of solution channels, un-oxidized sections, unleached areas, and compaction due to various factors, were found. These conditions are thought to represent a normal, rather than unique, situation for a valley fill heap leach. The lack of this information can have a significant impact on the economics and methods of heap re-handling and ultimate closure.

Jan 1, 1992

By William F. Stowasser

The United States has traditionally been the world's largest producer and net exporter of phosphate rock and related fertilizer products with the exception of rock exports from Morocco. In recent years, however, U.S. producers have faced increasing competition from operations in foreign countries, leaving the future position of the U.S. phosphate .industry as a leader in the world markets somewhat less certain. This paper will review the U.S. phosphate rock industry in relation to its known demonstrated reserves, its historical and present production and export levels, and its future mining potential. The paper will include an analysis of the availability of phosphate rock in the United States represented by cost-tonnage relationships. The U.S. phosphate rock industry has for decades provided raw materials at reasonable costs to the phosphate fertilizer industry, and the fertilizer products have been made available to both domestic and international markets. Natural soils normally contain low quantities of phosphorus, and cultivation exhausts the available phosphorus through the removal of harvested products. Yields diminish, and it becomes necessary to apply phosphorus to the soil in an amount at least sufficient to compensate for removal. Raising the level of phosphorus also permits nitrogen and potash fertilizer nutrients to be effective and sustain the high crop yields necessary to support increasing food demands. In only a few areas of the world are soils, climate, rainfall, and low-cost phosphate fertilizer available to assure high agricultural yields in successive years. One of these areas is the central United States and south central Canada. By contrast, in the Soviet Union, the weather conditions in farming areas frequently cause crops to either bake or drown in the field. To attempt to counter the effect of weather on production, the U.S.S.R. has increased use of fertilizer and equipment in recent years. The effect of fertilizer on various crops has been documented, and in all cases, improvements in yield and plant development were noted, as was the ability of fertilizer to mitigate the effects of unfavorable climatic conditions. Phosphate resources can be classified as either identified or undiscovered. In the identified classification, we are principally concerned with demonstrated phosphate resources, or those that have been measured or indicated. In the southeastern United States, the phosphate mining areas of Florida and the Carolinas have been explored and drilled extensively in attempts to locate new deposits. The exploration programs indicate that another Florida Bone Valley Formation or North Carolina Pamlico River Deposit is unlikely to be discovered in the southeastern U.S. coastal plain. Phosphate rock deposits of commercial interest in the western United States are located in Montana, western Wyoming, northern Utah, and southeastern Idaho. The deposits are in the Permian Phosphoria Formation with most of the mining activity occurring in Idaho. Although substantial demonstrated resources have been identified, recovery costs and the field's isolation from markets have restricted growth of the industry in the west. The phosphate rock deposits in Tennessee are well known, and it is estimated that about 29 million metric tons1 are potentially recoverable. Undiscovered deposits of brown rock in Tennessee would likely be quite small.

Jan 1, 1985

By L. Alagha, M. Khodakarami

"This work focuses on the extraction of rare earth metals (REE) from aqueous solutions using stimuli-responsive polymers. Various parameters affecting the adsorption capacity of the polymer, including pH, polymer concentration and REE concentration were studied. The interfacial behavior of REE in aqueous phase before and after polymer addition and the mechanism of the formation of metal-polymer complexes and their properties were investigated using UV/VIS spectroscopy. Results obtained would help to test the feasibility of employing stimuli responsive polymers in pre-concentration of rare earth elements associated with other elements in mineral aqueous streams prior to solvent extraction. The pre-concentration step would reduce the amount of organic solvents used for extraction and striping compared to conventional extraction processes. INTRODUCTION Rare earth elements (REEs) have become the foundation for several technologies and have been used extensively in many industries such as modern electronics, green energy, health care and transportation and defense [1-4]. As these industry sectors are growing, the global consumption of REEs is going to increase dramatically. The current global REEs demand is estimated to be 105,000 tons of rare earth oxides per annum with an expected annual growth of 5.6% [5-6]. Rare earth elements are produced from different sources (primary and secondary). China is considered as the largest producer of REE in the world, providing about 90% of the world’s mine production while the United States is second with 4% of the mine production [7]. High global demand for rare earth materials results in shortage of such materials in the near future. It should be considered that the term ‘‘rare’’ earth is not an accurate term, since they are abundant in some extent in the Earth’s crust, but are typically finely dispersed. Thus, nowadays looking for more efficient and cheaper methods for extraction, separation and purification of low concentrated REE ores and exploring secondary sources are essential. Rare earth materials are found in raw condition and require treatment that involves several processes, which can consume money and time. Recent improvements in extraction and recycling technology have made the extraction of rare earth elements from rare earth sources more feasible in terms of cost and time [8-10]. Physical and pyrometallurgical methods require high-energy and thus high costs. Moreover, due to environmental problems, environmental protection systems are required, and they are not as adaptable as chemical processes [11, 12]."

Jan 1, 2016

By E. J. Wade

My subject is gold price forecasting and monitoring as an important aspect of gold marketing. While I 'm specifically addressing gold, it is understandable that many other commodities could be readily substituted. Gold marketing must be studied as three distinct processes, and it is my intention to cover each of these processes in turn. First I?ll cover the process of gold price monitoring and forecasting in some detail. In order to select a method, or combination of methods, to be used to sell gold a determination of the future price profile is essential. The profitability of the sales effort will be determined, to a large extent, by how accurately the future price behavior of the gold market has been forecast.

Jan 1, 1985

By James Parkes

"The proposed Baltimore Red Line light rail system includes a 3.4 mile downtown tunnel (DTT) with five underground stations. The design of the underground stations involved overcoming several challenges, including limited right-of-way, high groundwater and uplift pressures, and metamorphic rock within the station depths. An innovative design was developed to maximize the internal station space while minimizing cost. The station designs use slurry walls for temporary and permanent support and groundwater control. Depths within rock are supported with cast-in-place concrete walls, the thickness of which are minimized through the use of permanent rock anchors for support of the rock mass and slurry wall toes. Permanent tiedown anchors are used for uplift resistance, which minimizes the station depths, volume of rock excavation, and the volume of deadweight concrete. Design considerations regarding individual elements and overall integration of the slurry walls, CIP walls, and multiple anchor types are presented.INTRODUCTION The Baltimore Red Line (BRL) project is a proposed light rail transit line for the Maryland Transit Administration (MTA) that runs east to west through Baltimore City and County. The project includes the Downtown Tunnel (DTT) consisting of 3.0 miles of twin running tunnels, two portals, five underground stations, and a pedestrian tunnel, as shown in Figure 1. The tunnels have an outside diameter of 21.8 feet and are designed to be mined using pressurized face tunnel boring machines (TBMs). The stations, portals, and the pedestrian tunnel are designed as cut-and-cover structures using slurry walls (concrete diaphragm walls) for both temporary support of excavation (SOE) and permanent structural walls. The dimensions of the five underground stations are summarized in Table 1. Design challenges included limited right-of-way (ROW), challenging soils conditions, strong metamorphic rock within the station depths, and high groundwater conditions. The final station designs included innovative use of slurry walls, tieback anchors, rock anchors, and tiedown anchors."

Jan 1, 2016

By III Westbrook

Although calcium sulfate dihydrate, commonly referred to as gypsum, has been utilized for some time in fiberglass reinforced polyester (FRP) applications, it does not have the fire retardant filler recognition of ATH. Gypsum is more commonly known for application in cement, soil and water treatment, plaster, and wall-board. Inherent characteristics of gypsum limit its use to low temperature and, until recently, non-aqueous applications. However, as a plentiful, naturally occurring hydrated mineral, the cost effectiveness of calcium sulfate dihydrate has prompted development and yielded success in the areas of FRP spray-up and latex carpet backing.

Jan 1, 1993

By Ramazan Comakli, Cemal Balci, Nuh Bilgin, Hanifi Copur, Can Polat, Deniz Tumac

"Application of mechanical excavators for rock excavation in both civil construction and mining engineering fields has increased significantly in recent years. Prediction of the excavation performance of any mechanical excavators – tunnel boring machines, roadheaders, impact hammers, continuous miners and shearers for any geological formation is one of the main concerns in determining the economics of a mechanized mining and/or tunneling operation. A new portable linear rock cutting (PLCM) device was developed in the Mining Engineering Department of Istanbul Technical University and supported by The Scientific and Technological Research Council of Turkey (TUBITAK-112M859). The PLCM is used for cutting small core or block rock samples by a real-life mini disc cutter. The results from the PLCM are compared with the results obtained from the full scale rock cutting tests and theoretical model. It is found that there is reliable correlation between test results obtained from both cutting tests and theoretical model. 1. INTRODUCTION Mechanical excavators are currently the only alternatives to drill and blast due to higher production rate, increased safety, uniform muck size, less roof support, easier ventilation, continuous rather than cyclical operation, and possibilities for automatic control. The most of large civil tunneling and some mining projects are now carried out by mechanical excavators rather than drill and blast methods. Mechanical excavators can be categorized into two main groups: full-face and partial-face machines. Full-face machines such as tunnel boring machines excavate the face in one mode at the size of the cutterhead. Due to their cutting mode, the shape of the face profile by the full-face machines can only be circular. As for partial-face machines, the cutterhead is attached at the end of a boom. The face profile excavated by the partial-face machines can be from circular to horseshoe shape due to the cutting mode of the boom."

Jan 1, 2016

Factors which cause thiourea consumption in gold-leaching systems include adsorption by gangue mineral particles, complexation with base metal ions, thermal degradation, and oxidation by air/ferric iron. Of these factors oxidation by ferric iron is the most significant factor. Of course, ferric sulfate is desired as an oxidant for the gold leaching reaction, but an excess of ferric sulfate leads to high thiourea consumption. In this regard, the rate of gold leaching by thiourea must be balanced against the rate of thiourea decomposition. It is important to note that the thiourea decomposition reaction in ferric sulfate solution is relatively slow in pure solutions and has been found to be first order with respect to both thiourea concentration and total ferric iron concentration. However, when mineral particles from gold-bearing ores or concentrates are present, the decomposition rate can become quite significant. As might be expected, the catalytic activity of mineral surfaces varies with particle composition and size. Experimental results are discussed with respect to the consumption of thiourea.

Jan 1, 1997

By B. G. Stone

"INTRODUCTION “Sampling is the process of taking a small portion of an article such that the consistency of the portion shall be representative of the whole” (Baxter and Parks, 1939) “An orebody is a mixture of minerals in proportions that vary in different parts of the mass. As a consequence the proportion of contained metals also varies from place to place. Therefore, a single sample taken in any particular place would not contain the same proportion of metals as does the orebody as a whole except by a highly improbable coincidence. The probable error, which would be very large if only one sample were taken, decreases with the number of samples, but it never disappears completely unless the samples are so numerous and so large that their aggregate is equal to the orebody itself, in which case the orebody would be completely used up in the process of sampling. Since carrying sampling to such an extreme would defeat its own purpose, some probable error is always present in actual cases and the practical objective is to reduce this probable error to allowable limits. This means balancing the number of samples against the desired accuracy; if there are not enough samples the result is unreliable; if there are too many, the time and expense of taking them is excessive.” (McKinstry, et al., 1948). In an actual orebody, the accuracy of sampling depends not alone on the number of samples but also on proper distribution of them throughout the orebody, for it would obviously be incorrect to take all of the samples either in a rich part or a lean part. Therefore it is important to select the places in such a way that all parts of the orebody will be represented. “For those who cultivate land which is alike arid, heavy , and barren, and in which they sow seeds, do not make so great a harvest as those who cultivate a fertile and mellow soil and sow their grain in that. And since by far the greater number of miners are unskilled rather than skilled in the art, it follows that mining is a profitable occupation to very few men, and a source of loss to many more.” (Georgius Agricola page 5 Book 1 as translated by H.C. Hoover and Lou Henry Hoover, 1950)“It is evident that mining is very profitable to those who give it care and attention”"

Jan 1, 2015

By G. V. Sullivan

As part of its program to conserve domestic mineral resources through advancing mineral resources technology, the U.S. Department of the Interior, Bureau of Mines, conducted investigations to determine the feasibility of recovering high-grade barite concentrates, suitable for use as well-drilling mud, from current and old waste pond materials and materials bypassed in present mining operations. Flotation studies of waste pond samples from Missouri and Nevada yielded barite concentrates containing over 95 percent BaSO4 with recoveries of 86 percent and 96 percent, respectively, of the barite in the flotation feed. Flotation studies of a hard-rock sample from Georgia, currently bypassed in mining, yielded a barite concentrate containing 97 percent BaSO4 with an attendant recovery of 97 percent of the barite.

Jan 1, 1980

By Yeonuk Choi, Patrick R. Taylor, Lyle Cunningham

Laboratory experiments have been performed to evaluate the potential for metal removal and recovery from river bed tailings by ferric chloride leaching. The lead, zinc, silver and other metals in the river bed occur due to the old method of dumping mill tailings into rivers. This was practiced prior to the introduction of tailings impoundments. The effects of the leaching method, leaching time, pulp density, ferric chloride concentration, and leaching temperature on the rates and recoveries of lead, zinc and silver were studied. The effects of pulp density and leaching temperature were significant on the extraction rates of lead, zinc and silver. The lead content in the leached tailing was reduced to 0.023 percent, when using an 353O K leaching temperature and 0.384 g of FeC13/1 g of sample.

Jan 1, 1992

By J. C. Haptonstall

Stoping methods at the Homestake Gold Mine through 1978 had been traditional overhand cut-and-fill, shrinkage or square set. High costs, low-productivity and safety concerns prompted the mine to search for and adopt a "bulk mining" technique as a primary stoping method. Blasthole stoping had been successful but it is very development intensive, and was not suitable for the mine's accelerated mining program. Vertical Crater Retreat stoping was selected, and today accounts for over 50% of ore production. Case histories representing both the successes and failures of VCR stoping in the mine are discussed.

Jan 1, 1986